Adds a consistency check to avoid OOPS, if tuner_callback priv argument is
NULL. Also, simplifies callback codes on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ISL6405 LNB supply is used on several Creatix / Medion cards. But only
the MD8800 needs its second section. So don't start it unless it is needed.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes reported problems when trying to add a 9th device into a
system.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner refactoring broke support of tuners with LNA configurations 1 and 2
for both, analog TV and DVB-T.
Additionally, this patch initializes the saa713x gpios defined by the gpiomask
at driver init to avoid undefined stated at dvb.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some restrictions:
- The 2nd DVB-S section will only work if the 1st is configured for DVB-S too.
so "options saa7134-dvb use_frontend=0,1" won't work.
- Currently it is not possible to set the higher LNB supply voltages, so
14V instead of 13V in the 2nd section.
- It is not possibe to turn off the 2nd LNB supply independently.
This comes from the problem that the 2nd section can't access the i2c interface
of the LNB supply chip.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the case of an access error to the high latency registers of
the audio DSP, the interface needs to be cleared, otherwise a cascade
of errors occurs.
This patch is closely modeled after a proposal by Mirek Slugen
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TUNER_PHILIPS_ATSC is an ambiguous name for a tuner. Rename it to
TUNER_PHILIPS_FCV1236D to be more descriptive.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner-xc2028 needs to know when a DVB module is sharing the same analog tuner.
This is done by comparing a magic number that needs to be the same on analog
and on digital. To make easier, this magic number is a pointer to some data
struct.
With the previous code, two different pointers were using, causing a
miss-detection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the following saa7134 xc3028 based boards:
132 -> AVerMedia Cardbus TV/Radio (E506R) [1461:f436]
133 -> AVerMedia Hybrid TV/Radio (A16D) [1461:f936]
134 -> Avermedia M115 [1461:a836]
135 -> Compro VideoMate T750 [185b:c900]
This is based on a original patch thanks to Markus Rechberger that added xc3028
gpio init code for the above boards.
This patch moves saa7134_tuner_callback to saa7134-cards, originally used only
by tda8290 DVB-S boards. The callback was made more generic to support other
tuners.
Currently, it supports both tda8290 and xc2028/xc3028 tuners. Added also the
basis for xc5000 tuner callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf-dma-sg does not need to depend on PCI. Switch it to using generic
DMA API, convert all affected drivers, relax Kconfig restriction, improve
compile-time type checking, fix some Coding Style violations while at it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The I2C bus interface of the LNB supply sits behind the i2c gate of the
tda10086, so wrappers were necessary for the set_voltage functions.
For the time being, the board will show up as MD8800
Many thanks to Hermann Pitton for his help
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support is not complete yet and untested.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are several parts of saa7134_board_init2() that calls tuner modules. We
should first load tuner, otherwise, the commands will fail.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This also has some coding style fixes.
Signed-off-by: Yuri Funduryan <yurifun@mail.ru>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cards need the diseqc signal modulated, while some just need
the envelope to control the LNB supply.
This fixes Bug 9887
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf functions at close() method already locks videobuf. It makes no sense
to keep the locking at empress close() method.
There is also a lock at open() method. I'm not sure if it is safe to remove the
locking there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134-dvb: add missing dvb_attach around tda10046_attach
This patch adds a possibly missing dvb_attach for tda10046_attach.
This removes the hard dependency of saa7134-dvb on tda1004x module.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Angelo Lisco for his initial patch we missed and to
Ahmet Dogan Ugurel confirming such a device functional.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for analog inputs and DVB-T.
Good sensitivity for DVB-T currently needs to use analog TV first.
DVB-S support is not yet completed, but is on the way.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It also enumerates now the separate composite input at first
and adds mute ability to radio and external audio-in.
Many thanks to Daftcho Tabakov for reporting the flaws and testing.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
S-Video is unconfirmed, but likely correct.
The remote is not yet investigated.
Thanks go to Sioux for providing code and asking to fix the auto
detection.
Signed-off-by: sioux <sioux_it@libero.it>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Thanks go to Mark Schultz for the initial contribution and to
Dean Hilkewich for testing it again.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134: remove the Avermedia Super 007 from eeprom detection
The card made it into the Philips' Tigers eeprom detection and falls through.
Since it has attracted already others to follow, which are wrongly identified
as TIGER_S then, move it to the usual analog initialization.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As in the past, we should not allow to auto detect like this,
since all saa7130 and saa7134 cards without eeprom will be detected
as such Beholder cards then.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch updates cardlist for Beholder TV tuners:
old models (with GPIO ir) 401, 403, 405, 407, 409, 505, 507
and add support for 607, 609, M6 cards with new i2c-ir.
Signed-off-by: Igor Kuznetsov <igk72@yandex.ru>
Signed-off-by: Andrey J. Melnikov <temnota@kmv.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Those newer functions are used by saa7134-empress. Adds export for them:
+EXPORT_SYMBOL_GPL(saa7134_g_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_s_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_queryctrl);
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134 were converted to video_ioctl2, but saa7134_empress weren't. This broke
saa7134-empress, since it were dependent of saa7134_common_ioctl.
With the conversion, the module had a size decrease of 436 bytes on x86_64:
text data bss dec hex filename
5196 4912 4 10112 2780 old/saa7134-empress.ko
4760 4912 4 9676 25cc new/saa7134-empress.ko
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VBI were broken, since there weren't any function handlers for it. This patch
fixes it, by removing the vbi_template, using, instead video_template.
This also saves some space at the data segment.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some functions are used also by saa7134-empress, and need to be exported. To
avoid namespace confusion, rename all of them to saa7134_
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch enabled the IR remote control for the Avermedia M102 (card=110),
which appears to be the same IR as the already supported device on the
Avermedia AVerTV GO 007 FM (card=57) model, the code is two one liners which
enable the IR for this device (subsystem: 1461:f31e)
Signed-off-by: Albert Graham <agraham@g-b.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After this patch, the order of the functions will be the same as before the
patch converting the driver to user video_ioctl2. This makes easier to diff
between the previous version and the newer one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the saa7134 chips only have mute support for the TV input.
Cards with mute from external audio muxes are already fine on the
other inputs and some recent tuners mute at least the radio on exit.
But these mostly hybrid tuners are not fully backward compatible, since
they must power down and mute regardless.
For some included above, the MD7134 knows several, to switch on mute/automute
to the TV input is functional and backward compatible for the applications,
except that the tuners with tda9887 always mute on exit.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move some tv-audio initialization code out of tvaudio thread,
and call it on resume too.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First the saa7134_initdev waits between saa7134_hwinit1
and saa7134_hwinit2 , thus it is probably wise to do the same in saa7134_resume
some hardware probably needs this.
Call saa7134_irq_video_signalchange in .resume like in saa7134_resume to make
saa7134_resume mirror perfectly the saa7134_initdev although
this call isn't strictly necessary in the saa7134_initdev,
but it won't harm anyway.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*dev->insuspend = 1 should be set before synchronize_irq
*ACK interrupts after synchronize_irq, to make sure there aren't
pending interrupts.
*Add barrier before we restart interrupts so the handler will 100%
see the dev->insuspend
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pci_save_state should be called before pci_set_power_state
and pci_restore_state after pci_set_power_state
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134-oss is deprecated for quite some time, it's the only remaining OSS
user outside of sound/oss/, and considering how few and what kind of
soundcards are left supported by OSS I hardly see any use cases left.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ability to read Hauppauge eeprom's was recently added to saa7134,
so we must build the tveeprom module.
Thanks to Matthias Schwarzott for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Increased size of dev->eedata from 128 to 256, since the Hauppauge data begins
at byte 128. This has been tested on boards with smaller eeproms, and caused
no problems.
Added comments to distinguish between the various versions of the HVR1110.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134_buffer_requeue() and set_tvnorm() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the only tuner-specific device that allows special
configurations is tda9887. However, tea5767 also may require some
special configurations (for example, to specify a different Xtal freq).
This patch replaces TDA9887_SET_CONFIG by a more generic internal ioctl
(TUNER_SET_CONFIG). The newer one allows specifying what tuner is
appliable to a configuration set, and allows an arbitrary configuration
struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correct wrong sized spinlock flags, form int to unsigned long.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks to Hermann Pitton for noticing that this was missing.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are several months my hvr1110 stop working.
This is very simple to fix, for my card revision at least, by setting a
missing field to the hauppauge_hvr_1110_config.
Signed-off-by: Benoit Istin <beistin@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134 video driver starts dropping frames when used together with the
saa7134-alsa driver. Frames are dropped because when an audio event is waiting
the driver simply ignores the interrupt and passes it on to the saa7134-alsa
interrupt handler. The alsa interrupt handler in turn acknowledges all types
of events thus clearing the pending video events as well. Fix by only masking
out the audio event in the video interrupt handler and by only acknowledging
the audio event in the alsa driver.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vmux for composite over s-video input was wrong.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The period handling in saa7134-alsa is broken in two ways. First, the
minimum number of periods of two does not work, because the dma is setup
two periods ahead in the irq handler. Fix the minimum to four periods.
Second, the code assumes that the number of periods is divisible by two,
which isn't always the case on ALSA. Fix by adding a constraint.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drivers were using cookie cutter code for stopping the read/stream. Use the
new videobuf_stop function which is lock safe.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho wrote:
> I do not think the saa7134-alsa driver supports mmap. The cx88-alsa driver
> also claimed to support mmap, but it never worked until I fixed it. It's
> pretty clear that the code in saa7134-alsa was based on the same code as
> cx88-alsa, so it's likely it has the same bug.
You are right. The patch below (based on your cx88 patch, but I don't
really understand it) fixes mmap support in saa7134-alsa for me.
Recording via mmap (arecord -M -f S16_LE -c 2 -r 32000 -D hw:1) didn't
work at all before, works now, tested for at least 20 minutes (but,
unfortunately, with one overrun at least 0.719 ms long).
Signed-off-by: Alexander E. Patrakov <patrakov@ums.usu.ru>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All of these drivers select VIDEO_IR, which uses the input subsystem,
so they should also depend on INPUT.
Problem examples:
drivers/built-in.o: In function `ir_input_key_event':
ir-functions.c:(.text+0x10849a): undefined reference to `input_event'
ir-functions.c:(.text+0x1084ac): undefined reference to `input_event'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11cc0a): undefined reference to `get_key_pinnacle_color'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11cc4f): undefined reference to `get_key_pinnacle_grey'
drivers/built-in.o: In function `saa7134_input_fini':
(.text+0x11cd8b): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d1fa): undefined reference to `input_allocate_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d317): undefined reference to `input_register_device'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11d6ca): undefined reference to `input_free_device'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c3f3): undefined reference to `ir_codes_hauppauge_new'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c450): undefined reference to `ir_codes_pinnacle_color'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c480): undefined reference to `ir_codes_purpletv'
drivers/built-in.o: In function `saa7134_set_i2c_ir':
(.text+0x11c495): undefined reference to `ir_codes_pinnacle_grey'
drivers/built-in.o: In function `saa7134_ir_start':
(.text+0x11c622): undefined reference to `ir_rc5_timer_end'
drivers/built-in.o: In function `saa7134_ir_start':
(.text+0x11c637): undefined reference to `ir_rc5_timer_keyup'
drivers/built-in.o: In function `build_key':
saa7134-input.c:(.text+0x11c769): undefined reference to `ir_extract_bits'
saa7134-input.c:(.text+0x11c7ad): undefined reference to `ir_input_keydown'
saa7134-input.c:(.text+0x11c7f0): undefined reference to `ir_input_keydown'
saa7134-input.c:(.text+0x11c7f9): undefined reference to `ir_input_nokey'
saa7134-input.c:(.text+0x11c806): undefined reference to `ir_input_nokey'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ca07): undefined reference to `ir_codes_encore_enltv'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11caf6): undefined reference to `ir_input_init'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cbf2): undefined reference to `ir_codes_avermedia'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc24): undefined reference to `ir_codes_pctv_sedna'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc53): undefined reference to `ir_codes_flydvb'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cc85): undefined reference to `ir_codes_videomate_tv_pvr'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ccb7): undefined reference to `ir_codes_pixelview'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cce9): undefined reference to `ir_codes_eztv'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cd1b): undefined reference to `ir_codes_manli'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cda8): undefined reference to `ir_codes_cinergy'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cdd7): undefined reference to `ir_codes_flyvideo'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ce06): undefined reference to `ir_codes_asus_pc39'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11ce7d): undefined reference to `ir_codes_gotview7135'
drivers/built-in.o: In function `saa7134_input_init1':
(.text+0x11cee1): undefined reference to `ir_codes_proteus_2309'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134: fix analog audio in on medion md8800 quadro, aka CTX944
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Calling saa7134_ir_stop at suspend is no good idea
for saa7134 cards without remote control.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
improve GoTView PCI7135 remote control working under linux.
Acked-by: Hermann Pitton <hermann-pitton@arcor.de>
Acked-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Eugene M. Roginskii <roginovicci@nm.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
make tvaudio thread freezeable, and add proper support for that
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes few more problems I found in my saa7134 resume code:
* Race between IRQ handler and .suspend()/.resume() functions
* Removes timeout timers on active buffers - those
buffers will be recaptured after resume
* Adds suspend/resume for IR code - probably
necessary if using polling mode
* Adds #ifdef CONFIG_PM overs suspend code
* Runs a quirk in set_tvnorm in suspend/resume too
* Rearranges the order of calls in saa7134_resume to
be exactly as in saa7134_initdev thus the card is
initialized in exactly the same way
* Since DMA audio capture suspend/resume isn't yet supported,
avoid re-enabling it on resume for now
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the obsolete VIDIOC_G_MPEGCOMP and VIDIOC_S_MPEGCOMP ioctls from
the V4L2 API as per the removal schedule (October 2007).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
struct video_device used to define a .hardware field. While
initialized on severl drivers, this field is never used inside V4L.
However, drivers using it need to include the old V4L1 header.
This seems to cause compilation troubles with some random configs.
Better just to remove it from all drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This removes NOP implementations of i2c_algorithm.algo_control.
With this change, there are no implementations of this hook in
the kernel.org tree ... that hook seems about ripe to remove.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A couple loops weren't changed because they expected the loop iterator
to be left as NULL if the list was empty. Maybe the code should just
check for that first, then loop?
Adjust some of the loop logic to be simpler.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*Disable DMA explictly on suspend
*Enable DMA on resume, after all buffers were configured
*Disable overlay on resume - apps should enable it when X is resumed
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Recognize the KWorld ATSC115 PCI ID as a hardware clone of the ATSC110.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CONFIG_VIDEO_BUF_DVB became CONFIG_VIDEOBUF_DVB.
But in these cases, it makes more sense to use CONFIG_VIDEO_SAA7134_DVB
or CONFIG_VIDEO_CX88_DVB_MODULE depending on the driver.
The reference in cx23885.h should just be removed, as the code there needs to
be included if DVB is on or off. I do not think you can even compile the
cx23885 driver without DVB. It's clearly just leftover from when the file was
obvious copied from the cx88 driver (which is not mentioned in the copyright
BTW).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
By "capturing interlaced video" I mean that card ensures that top field
is really top and vice versa (I think it takes the filed ID from signal)
Properly turn on/off that support depending on signal state
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for suspend/resume for core of saa7134
Should fix bug#7220
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When user sets dev->ctl_invert, driver writes negative values to
SAA7134_DEC_LUMA_CONTRAST and SAA7134_DEC_CHROMA_SATURATION,
but general code that initializes decorder ignores that
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
set_tvnorm can sleep in saa7134_i2c_xfer
(it will be called through tuner code)
but code calls it under spinlock. Fix that
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
PCI-dependent videobuf_foo methods were renamed as videobuf_pci_foo.
Also, videobuf_dmabuf is now part of videobuf-dma-sg private struct.
So, to access it, a subroutine call is needed.
This patch renames all occurences of those function calls to be
consistent with the video-buf split.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
http://thread.gmane.org/gmane.comp.video.video4linux/34978/focus=34981
Reviewed-by: Ricardo Cerqueira <v4l@cerqueira.org>
AverTV Studio 307 has only one composite input.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Acked-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix SVideo input on KWorld DVB-T 220 boards. Without this patch, the
luma pin on the SVideo input is treated as a composite in, and the
chroma pin is ignored.
Also, fix the radio, and provide a second composite input for people who
are used to the existing composite on SVideo connector behaviour.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were many instances of 7-space indents spread throughout
the v4l-dvb tree.
This patch replaces the 7-space indents with tabs. The whitespace cleaner
script doesn't catch these, because it assumes that all indents are 8-space.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This
patch removes all occurences of moduleparm.h from drivers/media files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add DVB-T support for Avermedia Super 007
Analog television is untested. The device lacks input adapters for radio,
svideo & composite -- seems to be a DVB-T ONLY device.
Signed-off-by: Edgar Simo <bobbens@gmail.com>
Acked-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a simple whitespace cleanup.
Signed-off-by: Edgar Simo <bobbens@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Right now the composite sound input doesn't work on AverTV 307 because of
the wrong mux setup. The composite sound is routed via an external
4channel multiplexer controlled by GPIO, while the code assumes an internal
multiplexer instead.
Presumably this was a copy/paste error, and noone have ever tested the
functionality.
With the attached patch it works properly, which gives me an ability to
finally watch the cable TV under linux.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It has been confirmed that the FlyDVB IR codes currently in the kernel
work with the LifeView FlyDVB-S LR300. This one line addition adds it
to the list of supported cards.
Signed-off-by: James Le Cuirot <chewi@aura-online.co.uk>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes all static dependencies on the dvb-pll module.
All exported dvb_pll_desc's have been UNexported, and the caller
will reference the individual dvb_pll_desc by it's index in the
pll_list array.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sound recording doesn't work for this card because ACNI and ACPF
are not set before snd_card_saa7134_capture_prepare(). As a result
timeout occurs. These registers aren't poked because thread
never gets wake up signal. ACNI initialization is done in the
thread.
Sound is muted when capture stops. Shouldn't be because it may
be used during TV playback.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In preparation for struct class_device -> struct device input
core conversion switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor at mail.ru>
Acked-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Enhance the dvb-pll definition of the fmd1216 tuner by adding an init sequence
and a sleep sequence.
The init sequence sets the AGC control register to 0xa0, selecting the fast
time constant and 112 dBuV take-over point. This the recommended value for
DVB-T operation.
The sleep sequence sets bit P4 (which is believed to turn the analog
demodulator on), turns off the tuning voltage, and sets the AGC control
register to 0x60 (external AGC voltage, the recommended value for analog
operation).
The existing dvb-pll users in the cx88 driver, listed below, will gain these
init and sleep sequences.
CX88_BOARD_HAUPPAUGE_HVR1100 Hauppauge WinTV-HVR1100 DVB-T/Hybrid
CX88_BOARD_HAUPPAUGE_HVR1100LP Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profi
CX88_BOARD_WINFAST_DTV2000H WinFast DTV2000 H
CX88_BOARD_HAUPPAUGE_HVR3000 Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DV
CX88_BOARD_HAUPPAUGE_HVR1300 Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encod
This non-dvb-pll user in the cx88 driver should only gain the sleep sequence,
as it already had an equivalent init sequence. The non-dvb-pll code for this
user is removed.
X88_BOARD_DNTV_LIVE_DVB_T_PRO digitalnow DNTV Live! DVB-T Pro
In these saa7134 driver, these non-dvb-pll users are converted to use dvb-pll:
SAA7134_BOARD_MD7134 Medion 7134
SAA7134_BOARD_ASUS_EUROPA2_HYBRID Asus Europa2 OEM
The saa7134 functions philips_fmd1216_tuner_init(),
philips_fmd1216_tuner_sleep(), and philips_fmd1216_tuner_set_params() are
deleted and the dvb-pll versions are used.
This should result in equivalent sleep, init, and tuning sequences being sent
to the tuner.
For the cxusb driver, only one board is effected:
USB_PID_MEDION_MD95700 Medion MD95700
This board used dvb_usb_tuner_init_i2c() and dvb_usb_tuner_set_params_i2c()
for init and tuning, respectively. These functions are effectively the same
as the dvb-pll versions. They call a tuner pass control function defined at
the dvb-usb level, but this does not matter, as this card does not have a
tuner pass control function (only the dib3000mb does). This board will gain
the sleep sequence, while init and tuning should be unchanged.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Using Encore's key codes, we needn't add any additional key table.
Signed-off-by: Tony Wan <wankai@sjtu.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support the 10moons TM300 TV card (so called TV Master 3), which is a
10moons saa7130 based board. Here not include features for the
IR-remote.
It has been tested using TVTIME. The card was auto-detected and all the
input sources worked correct with sound.
Signed-off-by: Tony Wan <wankai@sjtu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes duplicate code from cx88-dvb and saa7134-dvb that handles
rf input switching for the TUV1236d tuner.
The functionality is added to dvb-pll, where all the other code that
handles the TUV1236d is kept.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.
In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the test for the thread pid from >= 0 to > 0.
When the saa8134 driver initialization fails after a certain point, it goes
through the complete shutdown process for the driver. Part of shutting it
down includes tearing down the thread for tv audio.
The test for tearing down the thread tests for >= 0. Since the dev
structure is kzalloc'd, the test will always be true if we haven't tried to
start the thread yet. We end up waiting on pid 0 to complete, which will
never happen, so we lock up.
This bug was observed in Novell Bugzilla 284718, when request_irq() failed.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maintainer's notice: I needed to re-number the board, since the board
number conflicted with a patch committed previously.
Signed-off-by: James T Klaas <jklaas@appalachian.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the "Elitegroup ECS TVP3XP FM1246", the "KWorld DVB-T
210", and the Animation Technologies LR214 Rev F onwards (SAA7131) to
the saa7134 driver.
Also rename the LR214WF to the LR214 Rev E or ealier (SAA7135), to match
what we've seen on boards in the field.
Changed the comment on the Lifeview cards to indicate Rev E and earlier
versus Rev F and later, together with a chip indicator, following
feedback from Peter Missel <peter.missel@onlinehome.de>.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch just defines the remote control type.
Signed-off-by: Ed Vipas <epvipas@gmail.com>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the tuner is attached, the tda10046 is not initilized yet, so it
is searching for its firmware. If the tuner is attached to the tda10046
silent i2c port, a bus collision can occur. Now the version is probed
during the first init or sleep call.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The new name fits to what it is and what is on the box.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are 2 new entries for p7131 boards and one correction for a board
with LNA.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Static locals should not be changed - the original contents gets lost.
Thanks to Trent Piepho for pointing me to this.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Besides power saving, this puts the AGC output of the tda8290
to tristate. This is necessary for some hybrid boards which
don't use a multiplexer for the AGC
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the following compile error with CONFIG_MODULES=n:
CC drivers/media/video/saa7134/saa7134-core.o
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c:979:24: error: macro "request_submodules" passed 1 arguments, but takes just 0
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c: In function 'saa7134_initdev':
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c:979: error: 'request_submodules' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c:979: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c:979: error: for each function it appears in.)
make[5]: *** [drivers/media/video/saa7134/saa7134-core.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change some debug messages from printk() to dprintk().
Add KERN_WARNING and KERN_ERR level indicators to other printk()s that
lacked them.
Format printk lines with consistent ("%s/dvb: ", dev->name) prefix.
Fixed dprintk macro, which had an if with no else that wasn't protected
with a do {} while(0) block. That leads to "if(...) dprintk(); else" not
doing what one would expect.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The i2c data buffer in tda827xa_set_params was 1 byte too short
- saa7134-dvb now gives an error mesage if tda827x could not be attached
- coding style fix in tda1004x.c
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is a Lifeview Duo with a different ID
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change supplies a more generic version of the tuner callback.
The tuner struct now has a function pointer
int (*tuner_callback) (void *dev, int command, int arg)
additionally to a int config parameter.
both can be set through the TUNER_SET_TYPE_ADDR client call.
Note that the meaning of the parameters depend on the tuner type.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is for better consistency with other drivers
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The hardware is completely initialized afterwards, especially the
tda10046 has its firmware - which is also necessary in analog mode
of some hybrid boards.
Calling the sleep function afterwards saves power and definitely puts
hybrid boards into analog mode without additional code elsewere.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
During tuner attach, the pointers to host dev structure
are not set yet, so the I2c adapter needs to be accessed differently.
This patch also does some minor cleanup in the saa7134-dvb module.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch moves the tda827x dvb tuning code to a separate module
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are card variants supporting FM radio through tda8275.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains
- new tuning code for the tda827xa silicon tuner.
- controls the preamplifier of some boards with this tuner.
- support for the Philips Tiger S hybrid DVB-T reference design.
- reworked the saa7134-dvb modulue to get rid of most of the
small board specific functions.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These entries mainly are to support configurations of the tda827x
silicon tuner with a preamplifier.
The values can be set throgh the attach inform or through
the extended TUNER_SET_TYPE_ADDR client call. The function pointer
will only be updated if the parameter is not NULL.
Since a typecast is necessary to set the pointer, i added a typedef for
this pointer (tuner_gpio_func_t) in tuner.h
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This function allows to set, clear and tristate the GPIO ports.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are the following changes:
- separate configuration of IF and GPIOs.
- set GPIOs before firmware load. This helps to avoid I2C address
collisions.
- if desired invert GPIOs at sleep (automatic return to analog mode of card).
- added 3 tuner configuration bytes to config stuct.
- added i2c gate address to config struct.
- moved _state struct declaration to header file to make it accessible
on board layer.
- added "conf_probed" to the state struct to allow i.e. probing for correct
tuner version.
- changed firmware load mechanism to always:
+ check if already loaded
+ try to boot from eeprom
+ try downlad from host
- corrected name of tda10046 firmware image (backward compatible).
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The out of tree v4l-dvb build system didn't always override the kernel's
configuration settings with v4l-dvb's settings correctly. To work around
this, makefiles would define some new macro based on the setting of a
config variable. e.g. the pwc Makefile would define CONFIG_PWC_DEBUG if
CONFIG_USB_PWC_DEBUG (which is defined via Kconfig) was set.
The v4l-dvb build system should now always override correctly, and this
is no longer necessary. This patch gets ride of these extra defines and
just uses the CONFIG_* settings directly.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Terratec Cinergy HT PCI
Signed-off-by: Giorgio Moscardi <software@sukkology.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the following compile error:
<-- snip -->
...
LD drivers/media/video/built-in.o
drivers/media/video/saa7134/built-in.o:(.data+0x85ec): multiple definition of `ir_rc5_remote_gap'
drivers/media/video/bt8xx/built-in.o:(.data+0x734c): first defined here
drivers/media/video/saa7134/built-in.o:(.data+0x85f0): multiple definition of `ir_rc5_key_timeout'
drivers/media/video/bt8xx/built-in.o:(.data+0x7350): first defined here
make[4]: *** [drivers/media/video/built-in.o] Error 1
<-- snip -->
Since this variables were needlessly global, this patch implements the
trivial fix of making them static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a board definition for the Encore ENL-TV card, and
adds its PCI subdevice to the ID table.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This makes a second CVBS input available.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Besides adding the board specific code, this patch moves
the RC5 decoding code from bt8xx to ir-functions.c to make it available
for all drivers.
Signed-off-by: Marc Fargas <telenieko.telenieko.com>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
