pvrusb2: Remove use of volatile for command sequencer; these variables
are set by interrupt-context code and we check their state in such a
manner that there should be no race conditions. This had originally
been done out of paranoia, and I have since been convinced that the
paranoia is not required.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds a default video standard setting to the pvr2_device_desc
structure for describing device types. With this change it is
possible to set a reasonable default standard based on device type.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changeset allows the pvrusb2 driver to operate a new device type
("GOTVIEW USB2.0 DVD2"). Changes amount to defining a new routing
scheme for the device and adding appropriate table entries into
pvrusb2-devattr.c.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver has been successfully recovering from a crashed
encoder now for over 2 years. I think it's time to reduce the
perceived severity of the warning message. While I'd still very much
like to stop these crashes, the recovery logic is solid enough that
the problem is effectively benign. No point in panicing the users
over it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For Hauppauge 24xxx devices, the IR receiver is a custom piece of
logic that is very specific to the device. The pvrusb2 driver can
virtualize this to make it look like a more normal IR receiver found
in other Hauppauge devices. The decision of whether or not to enable
this virtualization however is a device-specific attribute, thus this
changeset.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The exact routing of video and audio signals within a device is a
device-specific attribute. Hauppauge devices do it one way; other
types of device may route things differently. Unfortunately it is
rather impractical to define chip-specific routing at the device
attribute level, so instead what happens here is that "schemes" are
defined. Each chip level interface implements its part of a given
scheme and the scheme as a whole is made into a device specific
attribute controlled via a table entry in pvrusb2-devattr.c. The only
scheme defined here is for Hauppauge devices, but clearly this opens
the door for other possibilities to follow.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Arrange so that the pvrusb2 driver can optionally work without a
Hauppauge ROM being present - which is fairly important for devices
that happen to not come from Hauppauge. The expected existence of a
Hauppauge ROM is now a device attribute. The tuner type is now also a
device attribute, which is consulted if there is no ROM.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correctly mark when a tuner type is set. Report more faithfully
information about known supported device video standards.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement additional pvrusb2 device info table entries for a device
identifier and a device description. Export this information via the
driver's internal API. Make this information available via the sysfs
driver interface. Also propagate this information into the v4l2
capability structure. An app can now retrieve and report a
descriptive string about the particular type of hardware device it is
operating.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Device-specific driver behavior is now defined by generic device
characteristics rather than by specific device model information.
With this change, the hardware type field can go away, thus this
change.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver currently supports two variants of the Hauppauge
PVR USB2. However there are other hardware types potentially
supportable, but the driver at the moment is not structured to make it
easy to describe these minor variations. This changeset is the first
set of changes to make such additional device support possible.
Device attributes are held in several tables all contained within
pvrusb2-devattr.c; all other device-specific driver behavior now
derives from these tables.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a new implementation for video pipeline control within the
pvrusb2 driver. Actual start/stop of the pipeline is moved to the
driver's kernel thread. Pipeline stages are controlled autonomously
based on surrounding pipeline or application control state. Kernel
thread management is also cleaned up and moved into the internal
control structure of the driver, solving a set up / tear down race
along the way. Better failure recovery is implemented with this new
control strategy. Also with this change comes better control of the
cx23416 encoder, building on additional information learned about the
peculiarities of controlling this part (this information was the
original trigger for this rework). With this change, overall encoder
stability should be considerably improved. Yes, this is a large
change for this driver, but due to the nature of the feature being
worked on, the changes are fairly pervasive and would be difficult to
break into smaller pieces with any semblence of step-wise stability.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the saa7134 chips only have mute support for the TV input.
Cards with mute from external audio muxes are already fine on the
other inputs and some recent tuners mute at least the radio on exit.
But these mostly hybrid tuners are not fully backward compatible, since
they must power down and mute regardless.
For some included above, the MD7134 knows several, to switch on mute/automute
to the TV input is functional and backward compatible for the applications,
except that the tuners with tda9887 always mute on exit.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
DVB-S is not supported. Also, there are some QAM6 firmwares for xc3028, but it
is reported that this doesn't work fine.
Thanks to Manu Abraham, Michael Krufky and Patrick Boettcher for their
insights.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Force tuner init after attach, then sleep until use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A previous patch implemented support for non-OFDM digital TV. However, the
previous bandwidth ofdm parameter were left at the code by mistake.
Thanks to Michael Krufky and Patrick Boettcher for noticing this mistake.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
s-code tables are related to IF frequency used for video demodulation.
The s-codes for analog are automatically loaded, according with video standard.
However, for digital, they will depend on the IF of the demoduler chip. IF of
the demoduler.
Before this patch, only a few IF's where possible to use. This patch allows
selecting any IF defined at firmware file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since check_firmware is called via analog or digital set freq routines, move
type selection to those routines. This avoids having several if's at the code,
and simplifies the source code.
A sideback effect is that implementing radio and other dvb types will become
simpler.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move some tv-audio initialization code out of tvaudio thread,
and call it on resume too.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First the saa7134_initdev waits between saa7134_hwinit1
and saa7134_hwinit2 , thus it is probably wise to do the same in saa7134_resume
some hardware probably needs this.
Call saa7134_irq_video_signalchange in .resume like in saa7134_resume to make
saa7134_resume mirror perfectly the saa7134_initdev although
this call isn't strictly necessary in the saa7134_initdev,
but it won't harm anyway.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*dev->insuspend = 1 should be set before synchronize_irq
*ACK interrupts after synchronize_irq, to make sure there aren't
pending interrupts.
*Add barrier before we restart interrupts so the handler will 100%
see the dev->insuspend
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pci_save_state should be called before pci_set_power_state
and pci_restore_state after pci_set_power_state
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes a few remainders of the VID_HARDWARE_* removal.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
643d01fb38b6f376cced035549f4e193018776e7
On some cases, xc2028/xc3028 wents into "turn off" mode. It seems that this
happens when very weak signals are tuned. To solve this, specific standard
reaload were done previously. Christopher patches changed this behavior to a
complete firmware reload.
This patch removes the hack. A much cleaner solution for this trouble is just
to sent a xc2028/3028 software reset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
xc3028 can be used on some DTV only designs (for example, DVB-S boards). Before
this patch, a DTV only board would need to call set_tuner_config callback.
This patch allows to optionally pass a xc3028_ctrl parameter, via xc3028_config
struct, fully initializing the driver for DTV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Xc2028.3028 has two type of firmwares: audio-standard specific ones and
baseband MTS firmwares. MTS firmwares provide stereo decoding for 6 MHz
BTSC/EIAJ and for monoaural audio decoding on 8 MHz firmwares.
It seems that the option to use MTS or a standard-specific audio decoding
depends on the way xc2028/3028 is connected.
Instead of wasting 32 (or 64 bits) to signalize if the driver needs to use MTS
firmware, this patch converts it to a bitfield that can be shared with other
proprieties of xc2028/3028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some drivers call set_frequency before selecting the video standard. Before
this patch, an invalid standard ID could be assumed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When loading init1 firmware, there may not be an 8MHz specific version.
Load the non-8MHz version if it exists.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When searching for standard-specific analog firmware, only certain
type bits are valid, much like for DTV. Mask them off when finding
the firmware to load.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When loading BASE firmware, we must use std = 0.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add sleep method to enable putting the tuner into standby mode.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In practice, the tuner occasionally fails to respond correctly after a
firmware load. Retry the firmware load if the firmware/hardware version
we read back from the tuner after programming does not match what we
expect.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define a list of valid "firmware types" for each combination of BASE,
DTV and SCODEs. By masking the appropriate firmware bits off we can
just use one "type" for the firmware searching and also flag when we
are looking for a BASE, DTV or SCODE type firmware. This makes it
much easier to track if we need to change device modes or flash an
individual firmware part.
Add a structure to remember what firmware properties we have. This
contains the currently loaded/wanted base firmware (type), video std
(id), video std requested (std_req), scode file and number in use.
Incorporate said structure into the tuner private data.
When checking whether the current firmware needs to be reloaded, first
figure out exactly what "type" of firmware we want (base, std and
scode), and then proceed to load the appropriate matching base,
std-specific and scode records iff there are any changes required.
This removes guesswork from the process because we no longer need to
individually code a check for every tuning parameter's interactions.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a bit to select D2633 DTV firmware to struct xc2028_ctrl, so that it can
be enabled via .set_config.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When validating and loading SCODE firmware we need to take into account the
two-byte size header before each entry.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than picking the first video standard firmware that supports any of
the standards that the user has requested, try to select one that supports
as many of them as possible. This improves the likelihood that the firmware
we select will support the user's desired TV standard.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is no need to duplicate the max_len field from the ctrl structure
in the private data. If we use it directly from priv->ctrl, we can memcpy
the structure (apart from strings) to reduce maintenance as it grows.
Enforce a minimum max_len length of 8 data bytes (+ 1 address byte) as seems
to be required by the tuner.
Also, use kstrdup instead of open coding the string duplication.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
7MHz bandwidth DVB-T needs an adjusted offset at the PLL to ensure the IF
output is correctly centered.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We were using priv->bandwidth to select the base firmware to load, not the
requested bandwidth value, oops. Also, 7MHz Digital TV needs 8MHz base
firmware loaded.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The frequency divisor should only be four bytes long. Also, display the
frequency and divisor correctly in the debug output.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hold the private lock over set_config and set priv->firm_size to 0 after a
failed firmware load to prevent firmware accidentally being freed on us.
Clean up the firmware load/error messages somewhat and rename priv->version
to priv->firm_version to make it clear which "version" it is.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add break to stop us from following the default failure path even upon success.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Protect refcount changes and modifications to xc2028_list with a mutex.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cast v4l2_std_id variables to unsigned long long so they will printk properly.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix some missing spaces in errors that may be emitted during attach failure.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Issuing register reads as a separate address write and data read transactions
means that other I2C activity could occur in between and state could get out
of sync. Issue both the write and read in a single transaction so that the
i2c layer can prevent other users accessing the bus until we are complete.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The I2C macros have side effects and send_seq could cause a return from
a function with a mutex held. Change them to behave like real functions.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134-oss is deprecated for quite some time, it's the only remaining OSS
user outside of sound/oss/, and considering how few and what kind of
soundcards are left supported by OSS I hardly see any use cases left.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ability to read Hauppauge eeprom's was recently added to saa7134,
so we must build the tveeprom module.
Thanks to Matthias Schwarzott for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The HVR-900 requires the MTS version of the xc3028 firmware in order
to get any sound. The below patch selects this firmware variant on
HVR-900 cards, as well as splitting the HVR-950 into its own entry
(since I don't know if it uses the MTS variant and it will have to be
split off eventually anyway).
Signed-off-by: Aidan Thornton <makosoft@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TM5600/TM6000 needs clock reset during firmware load. This patch adds the
capability of caling a callback method for this.
Also, avoids uneeded firmware loads.
Signed-off-by: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removes uneeded parameters and adds an structure for passing the parameters
This patch is co-authored by Mauro Carvalho Chehab.
Signed-off-by: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Increased size of dev->eedata from 128 to 256, since the Hauppauge data begins
at byte 128. This has been tested on boards with smaller eeproms, and caused
no problems.
Added comments to distinguish between the various versions of the HVR1110.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While there's no public API to define audio standard, adds a hack option for
select them. This is needed only for NICAM and A2 firmwares, since AM, BTSC and
EAIJ are already properly handled, on firmware version 2.7.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make the driver less verbose by default. It adds a debug parameter to make the
driver more verbose.
Also, error messages were using KERN_ERR level, instead of KERN_INFO.
A few printk messages were reviewed to make them more clear.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some tuners, like xc3028, need to print error messages. Instead of declaring
local macros, create a tuner global macro for printing tuner errors.
To preserve CodingStyle on all tuner_macros, a few CodingStyle violations were
fixed at the other macros:
- lines with more than 80 columns
- two statements at the same line
The patch also removes the CodingStyle violation of having emacs declarations
inside de source code (CodingStyle chapter 18).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Xceive 2028/3028 has a concept of scode/dcode.
Scode is a table of 16 values (each with 12 bytes i2c sequence).
Dcode is the entry of Scode table that should be used, given a certain
frequency.
The idea is that, depending on what frequency is selected, and according with a
country-based (or standard-based?) table, the Xceive should be "hacked" to
fine-tune that specific frequency.
By default, Scode=0 is used, for undefined frequencies. Also, Scode=0 seems to
be the most used value.
This patch adds the capability of selecting a scode. However, extra work will
be needed to allow auto-selecting the proper scode, for a given set of
frequencies.
I'm not sure what would be the proper way for implementing the dcode selection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Firmware version 2.7 has other firmware types. This patch adds the capability
for the driver to work with those newer types.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds a new image sensor to the sn9c102 driver.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the conversion to the vidio_ioctl2, tvnorms array is not required anymore.
Also, removed some code from V4L1 time (VIDEO_MODE_foo), specied at the
non-used video_decoder.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were some vestiges of an old V4L1 I2C driver that were called by em28xx.
This patch removes this dead code, and replaces videodev.h to videodev2.h
Now, this driver doesn't require V4L1 anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Uses the newer ioctl handler at videodev. This patch also cleans up some
bad logic at the driver and do CodingStyle and other cleanups at the
resulting driver.
Also, since VIDIOCMBUF were not working, the V4L1 compat code were removed.
The compat code will eventually be re-inserted, if we find a clean way for
implementing compatibility with the old API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On some situations, closing an streaming application and re-opening were
returning -EBUSY.
Uses the same locking schema also present on cx88.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allows shared access support for em28xx. Just one userspace application is
allowed to get stream. The other(s) application(s) can change V4L2 controls,
set video standards, etc.
This patch were splited from Markus Rechberger's tree and backported to 2.6.17
by Pádraig Brady.
The original patch were ported to the latest em28xx version and had CodingStyle
corrected to solve the issues pointed by scripts/checkpatch.pl.
Thanks to Pádraig Brady <P@draigBrady.com> for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L: Int if: Set slave's master before attach, remove master argument
The master also now gets its own pointer from slave's structure.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions in
et61x251_core.c static:
- et61x251_read_reg()
- et61x251_i2c_try_read()
- et61x251_i2c_try_write()
- et61x251_i2c_read()
- et61x251_i2c_write()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions static:
- cx8802_init_common()
- cx8802_fini_common()
- cx8802_suspend_common()
- cx8802_resume_common()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Trent Piepho for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hauppauge firmwares can be decoded using tveeprom. This patch adds HVR-900 as
a tveeprom client. It also adds xc3028 tuner entry to tveeprom.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The status registers require a dword for setting register. Fix it on all
occurrences, and at xc3028_get_reg. Also, improves the hardware/firmware
detection printk.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default_mode_mask global is replaced by a list of tuner structs. The
tuner driver now walks that list to see which radio and/or tv tuner
devices are registered to a given i2c adapter.
The default_mode_mask global had to go since this is no longer supported
with the new bus-based I2C API.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To ensure prevention of detecting a tda9885/6/7 as a tda8290 or tda8295, we
will rule out the tda988x before testing the tda8290 / tda8295 id registers.
We read 8 bytes from the chip. If they are all equal, then it is not a
tda829x, or some other error has occurred.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
From: Mauro Carvalho Chehab <mchehab@infradead.org>
In file included from drivers/media/video/em28xx/em28xx-i2c.c:31:
drivers/media/video/tuner-xc2028.h:10:26: error: dvb_frontend.h: No such file or directory
In file included from drivers/media/video/em28xx/em28xx-i2c.c:31:
drivers/media/video/tuner-xc2028.h:32: warning: 'struct dvb_frontend' declared inside parameter list
drivers/media/video/tuner-xc2028.h:32: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
From: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/tda8290.c:27:21: error: tda827x.h: No such file or directory
drivers/media/video/tda8290.c:28:22: error: tda18271.h: No such file or directory
drivers/media/video/tda8290.c:52: error: field 'cfg' has incomplete type
drivers/media/video/tda8290.c: In function 'tda829x_find_tuner':
drivers/media/video/tda8290.c:590: error: implicit declaration of function 'tda18271_attach'
drivers/media/video/tda8290.c:598: error: implicit declaration of function 'tda827x_attach'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
