Add support for X-ES single-board computers based on the Freescale
MPC85xx processors.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following series implements basic board support for
the kmeter1 board from keymile, based on a MPC8360.
This series provides the following functionality:
- The board can boot with a serial console on UART1
- Ethernet:
UCC1 in RGMII mode
UCC2 in RGMII mode
UCC4 in RMII mode
UCC5 in RMII mode
UCC6 in RMII mode
UCC7 in RMII mode
UCC8 in RMII mode
following patch is necessary for working UCC in RMII mode:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070804.html
- Flash accessed via MTD layer
On this hardware there is an Intel P30 flash, following patch
series is necessary for working with this hardware:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/070624.html
- I2C using I2C Bus 1 from the MPC8360 cpu
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.
The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..
mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.
Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the platform-specific code for enabling SWIOTLB if needed on P2020DS,
MPC85xx DS, and MPC85xx MDS boards as they are capable of having >4G of
memory.
We determine if we need to enable swiotlb based on how much memory is in
the board and if it exceeds 4G or what we can map via PCI inbound
windows.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is the final bit of code to allow enabling swiotlb on
mpc86xx. The platform-specific code is very small and consists
of enabling SWIOTLB in the config file, registering the
swiotlb_setup_bus_notifier initcall, and setting pci_dma_ops
to point to swiotlb_pci_dma_ops if we have more memory than
can be mapped by the inbound PCI windows.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently the FLASH database is updated by the kernel using file operations,
meant for userspace only. While this works for us because copy_{from,to}_user()
on powerpc can handle kernel pointers, this is unportable and a bad example.
Replace the file operations by callbacks, registered by the ps3flash driver.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
They were never intended to be exported using EXPORT_SYMBOL() anyway
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It reports the failure of a call to lv1_put_iopte(), not
lv1_map_device_dma_region().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
signal_vsp_instruction() is currently only used if CONFIG_PROC_FS
is enabled. However logically it has nothing to do with PROC_FS,
so rather than making it depend on that mark it as maybe unused.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If CONFIG_BLK_DEV_INITRD is unset dt_prop_u64() is unused, which
causes a warning. We don't really want to tie the definition to
BLK_DEV_INITRD, so mark it as maybe unused.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Axon MSI driver incorrectly uses platform_data, rather than
the proper accessors for driver_data.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Both arch/powerpc/platforms/cell/iommu.c and arch/powerpc/platforms/ps3/mm.c
contain the same Cell IOMMU page table entry definitions. Extract them and move
them to <asm/iommu.h>, while adding a CBE_ prefix.
This also allows them to be used by drivers.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 45db924089 ("powerpc/spufs: Remove
double check for non-negative dentry") removed the only user of the
out_dput label, so remove it and the code following it.
Gets rid of this warning:
arch/powerpc/platforms/cell/spufs/inode.c: In function 'spufs_create':
arch/powerpc/platforms/cell/spufs/inode.c:647: warning: label 'out_dput' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
resource_size_t is 64 bits on pseries
Gets rid of these warnings:
arch/powerpc/platforms/pseries/iommu.c: In function 'pci_dma_bus_setup_pSeries':
arch/powerpc/platforms/pseries/iommu.c:391: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
arch/powerpc/platforms/pseries/iommu.c:417: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch introduce a new Kconfig option, CONFIG_PPC_BOOK3S
that represents processors that are compliant with the "classic"
(aka "server") variant of the PowerPC architecture.
It replaces CONFIG_6xx on 32-bit (though the symbol is still
defined for compatibility) and encompass all currently supported
64-bit processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the Xilinx plbv46-pci-1.03.a PCI host
bridge IPcore.
Signed-off-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This cleans up the kilauea/halekala board ports to use the ppc40x_simple
platform support.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This cleans up the makalu board port to use the ppc40x_simple platform
support.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
RTAS event scan has to run across all cpus. Right now we use a kernel
thread and set_cpus_allowed but in doing so we wake up the previous cpu
unnecessarily.
Some ftrace output shows this:
previous cpu (2):
[002] 7.022331: sched_switch: task swapper:0 [140] ==> rtasd:194 [120]
[002] 7.022338: sched_switch: task rtasd:194 [120] ==> migration/2:9 [0]
[002] 7.022344: sched_switch: task migration/2:9 [0] ==> swapper:0 [140]
next cpu (3):
[003] 7.022345: sched_switch: task swapper:0 [140] ==> rtasd:194 [120]
[003] 7.022371: sched_switch: task rtasd:194 [120] ==> swapper:0 [140]
We can use schedule_delayed_work_on and avoid the unnecessary wakeup.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can compile and boot with NR_CPUS=8192, so make this the max. 1024
was an arbitrary decision anyway.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
arch/mips/sibyte/bcm1480/irq.c
arch/mips/sibyte/sb1250/irq.c
Merge reason: we gathered a few conflicts plus update to latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: merge almost-rc8 into perfcounters/core, which was -rc6
based - to pick up the latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Something in the HW or FW setup is busted and MSIs aren't working with
IPR on Bimini, so until we figure out exaxtly what's up, we quirk them
out
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the device node. We should
be calling pci_device_to_OF_node().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch removes an unnecessary double check if the dentry returned by
lookup_create() is actually non-negative. Since lookup_create() itself returns
an error in this case just remove the check.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There doesn't appear to be any specific reason that we need to setup the
pseries specific notifier in generic arch pci code. Move it into pseries
land.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the device node to just
go get the pci_controller. We can call pci_bus_to_host() for this
purpose.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the device node but call
pci_bus_to_OF_node() for this purpose.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't call __do_IRQ() directly in gatwick_action(), use
generic_handle_irq().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ps3 has 4 ipis per cpu and can use the new smp_request_message_ipi to
reduce path length when receiving an ipi.
This has the side effect of setting IRQF_PERCPU.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds support for the "unused" page hint which can be used in shared
memory partitions to flag pages not in use, which will then be stolen
before active pages by the hypervisor when memory needs to be moved to
LPARs in need of additional memory. Failure to mark pages as 'unused'
makes the LPAR slower to give up unused memory to other partitions.
This adds the kernel parameter 'cmo_free_hint' to disable this
functionality.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that leds-gpio is a proper OF platform driver, the Warp can use
the leds-gpio driver rather than the old out-of-kernel driver.
One side-effect is the leds-gpio driver always turns the leds off
while the old driver left them alone. So we have to set them back to
the correct settings.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8569 is similiar to the MPC8568. It doubles the number of
QUICC Engine RISC cores from 2 to 4. Removes eTSECs, TLU and adds
the eSDHC controller.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Keep an unique machine def for the MPC8568 MDS board to handle some
subtle differences between the future MDS board. Also set the bcsrs in
setup_arch() only for mpc8568_mds because other mds has different bcsr
settings.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the need for asm/mpc86xx.h as it was only used in mpc86xx_smp.c
and just moved the defines it cared about into there. Also fixed up
the ioremap to only map the one 4k page we need access to and to iounmap
when we are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor the check to determine if the quirk is applicable to the boards
into one inline function so we only have to change one place to add more
boards that the quirks might be applicable to.
Also removed a warning related to unused temp variable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Revert "mm: add /proc controls for pdflush threads"
viocd: needs to depend on BLOCK
block: fix the bio_vec array index out-of-bounds test
There have been a series of checkstops on QS21 related to
ptcal being set up incorrectly. On systems that only
have memory on a single node, ptcal fails when it gets
a pointer to memory on the remote node.
Moreover, agressive prefetching in memcpy and other
functions may accidentally touch the first cache line
of the page that we reserve for ptcal, which causes
an ECC checkstop.
We now allocate pages only from the specified node, moves the
ptcal area into the middle of the allocated page to avoid
potential prefetch problems and prints the address of the
ptcal area to facilitate diagnostics.
Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
