* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
[IPCONFIG]: The kernel gets no IP from some DHCP servers
b43legacy: Fix module init message
rndis_wlan: fix broken data copy
libertas: compare the current command with response
libertas: fix sanity check on sequence number in command response
p54: fix eeprom parser length sanity checks
p54: fix EEPROM structure endianness
ssb: Add pcibios_enable_device() return value check
rc80211-pid: fix rate adjustment
[ESP]: Add select on AUTHENC
[TCP]: Improve ipv4 established hash function.
[NETPOLL]: Revert two bogus cleanups that broke netconsole.
[PPPOL2TP]: Add missing sock_put() in pppol2tp_tunnel_closeall()
Subject: [PPPOL2TP] add missing sock_put() in pppol2tp_recv_dequeue()
[BLUETOOTH]: l2cap info_timer delete fix in hci_conn_del
[NET]: Fix race in generic address resolution.
iucv: fix build error on !SMP
[TCP]: Must count fack_count also when skipping
[TUN]: Fix RTNL-locking in tun/tap driver
[SCTP]: Use proc_create to setup de->proc_fops.
...
This fixes the module init message to tell that the legacy
driver loaded. This makes it less confusing, in case both drivers are loaded.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace broken code that attempted to copy 6 byte array to 64-bit
integer. Due to missing cast to 64-bit integer, left shift operation
were 32-bit and lead to bytes been copied over each other. New code
uses simple memcpy, for greater readability and efficiency.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Slightly more useful if we compare it against the sequence number of the
command we have outstanding, rather than comparing the reply with itself.
Doh. Pointed out by Sebastian Siewior
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I called p54_parse_eeprom() on a hand-coded structure
I managed to make a small mistake with wrap->len which caused
a segfault a few lines down when trying to read entry->len.
This patch changes the validation code to avoid such problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the EEPROM structure is read from hardware, it is
always little endian, annotate that in the struct and
make sure to convert where applicable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FEC driver has a common interrupt handler for all interrupt event
types. It is raised on a number of distinct interrupt vectors.
This handler can't be re-entered while processing an interrupt, so
make sure all requested vectors are flagged as IRQF_DISABLED.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Every skb removed from session->reorder_q needs sock_put().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every skb removed from session->reorder_q needs sock_put().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current tun/tap driver sets also net device's hw address when asked to
change character device's hw address. This is a good idea, but it
misses RTLN-locking, resulting following error message in 2.6.25-rc3's
inetdev_event() function:
RTNL: assertion failed at net/ipv4/devinet.c (1050)
Attached patch fixes this problem.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several endianity corrections in start_xmit()
Fixed TSO bug where packets were missing the TCP flags.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit traffic through an internal queue to prevent overflow.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed locking between fastpath and slowpath operations.
Corrected order of traffic disabling to prevent race when going down
under traffic.
- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC
Got rid of in_reset_task.
Remove_one() and friends would deference a null pointer if init_one
failed.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the HW attentions, used to indicate an error were not properly
acked.
This will cause the driver to endlessly receive interrupts when such
an error happens.
Had to break the code into smaller chunks because it got too nested.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata A0.158 workaround.
Running in INT#A mode after running with MSI-X fails due to a PCI core
bug.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errors were summed improperly, some stats were missing.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration of RX filtering needed the following corrections:
Drop flags need to be set per Rx queue.
Have to tell the microcode to collect drop stats, and properly wait
for them to complete when going down.
Sometimes we failed to detect proper completion due to a logical error
in the wait loop.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly protect PHY access between two devices on the same board with
a HW lock.
Use GPIO to clear all previous configurations before changing link
parameters.
Shut down the external PHY in case of fan failure.
Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.
Resolve the flow control response according to autoneg with external
PHY.
Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.
LASI indication fixes to work with peculiarities of PHYs.
Disable MAC RX to avoid a HW bug when closing the MAC under traffic.
Disable parallel detection on HiGig due to HW limitation.
Updating the shared memory structure to work with the current
bootcode.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct PCI-E info printed by init_one()
In one case it failed to free the netdev.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.
Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports. lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.
A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:
drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.
Reorder the things that should be done during a
link tuner reset and during a link tuner start.
Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.
Also don't configure the antenna when there has been
no change in the antenna setup.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix 2 issues in antenna diversity selection.
1) the following statement will always return true.
if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.
2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
| CC drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link the net_device structure of the wireless part to the
corresponding device structure.
Without this, the sysfs node for this net_device would not have
'device' link.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously wrong to use an enum in a little endian struct,
and those other enums should be declared differently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch avoids a denial of service from an evildoer sending a
continuous stream of flow control at our adapter that is plugged
into a non-flow control enabled switch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This simplifies the 82571/2/3 family initialization a bit
and removes an initialization table no longer needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This counter is valuable to determine if the system is unable
to timely return buffers to the hardware and this counter starts
to increase well before the hardware starts to drop packets. If
users experience rx_no_buffer_count increasing, they should increase
the amount of descriptors. That will provide more buffers for the
hardware and will decrease the chance of hard drops.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix NCFGR.SPD setting on 10Mbps. This bug was introduced by
conversion to generic PHY layer in kernel 2.6.23.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use register offset definition for WOLcgClr, rather than a magic
number.
This patch does not change the driver behaviour.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch eliminates a kernel panic with the igb driver in 2.6.25-rc2 when
running on a Intel 82575 Ethernet controller with a 1000BASE-SX PHY. The
panic does not happen with the 1000BASE-T PHY, only with a SX connection.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change all dma op invocations in gianfar.c to actually pass in the
device pointer. Currently, the value is ignored, but it will be
used going forward as we implement archdata for 32-bit powerpc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading a serie of zero from the cmos sram area do not work
well with is_valid_ether_addr(). Let's read the mac address
from the eeprom first as it seems more reliable.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9831
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The forward declarations were already marked static, make the definitions
be static as well. Fixes the sparse warnings as well.
drivers/net/tlan.c:1403:5: warning: symbol 'TLan_HandleInvalid' was not declared. Should it be static?
drivers/net/tlan.c:1435:5: warning: symbol 'TLan_HandleTxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1521:5: warning: symbol 'TLan_HandleStatOverflow' was not declared. Should it be static?
drivers/net/tlan.c:1557:5: warning: symbol 'TLan_HandleRxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1692:5: warning: symbol 'TLan_HandleDummy' was not declared. Should it be static?
drivers/net/tlan.c:1722:5: warning: symbol 'TLan_HandleTxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1770:5: warning: symbol 'TLan_HandleStatusCheck' was not declared. Should it be static?
drivers/net/tlan.c:1845:5: warning: symbol 'TLan_HandleRxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1905:6: warning: symbol 'TLan_Timer' was not declared. Should it be static?
drivers/net/tlan.c:1986:6: warning: symbol 'TLan_ResetLists' was not declared. Should it be static?
drivers/net/tlan.c:2046:6: warning: symbol 'TLan_FreeLists' was not declared. Should it be static?
drivers/net/tlan.c:2095:6: warning: symbol 'TLan_PrintDio' was not declared. Should it be static?
drivers/net/tlan.c:2130:6: warning: symbol 'TLan_PrintList' was not declared. Should it be static?
drivers/net/tlan.c:2166:6: warning: symbol 'TLan_ReadAndClearStats' was not declared. Should it be static?
drivers/net/tlan.c:2242:1: warning: symbol 'TLan_ResetAdapter' was not declared. Should it be static?
drivers/net/tlan.c:2328:1: warning: symbol 'TLan_FinishReset' was not declared. Should it be static?
drivers/net/tlan.c:2451:6: warning: symbol 'TLan_SetMac' was not declared. Should it be static?
drivers/net/tlan.c:2493:6: warning: symbol 'TLan_PhyPrint' was not declared. Should it be static?
drivers/net/tlan.c:2542:6: warning: symbol 'TLan_PhyDetect' was not declared. Should it be static?
drivers/net/tlan.c:2589:6: warning: symbol 'TLan_PhyPowerDown' was not declared. Should it be static?
drivers/net/tlan.c:2614:6: warning: symbol 'TLan_PhyPowerUp' was not declared. Should it be static?
drivers/net/tlan.c:2635:6: warning: symbol 'TLan_PhyReset' was not declared. Should it be static?
drivers/net/tlan.c:2663:6: warning: symbol 'TLan_PhyStartLink' was not declared. Should it be static?
drivers/net/tlan.c:2750:6: warning: symbol 'TLan_PhyFinishAutoNeg' was not declared. Should it be static?
drivers/net/tlan.c:2906:5: warning: symbol 'TLan_MiiReadReg' was not declared. Should it be static?
drivers/net/tlan.c:2996:6: warning: symbol 'TLan_MiiSendData' was not declared. Should it be static?
drivers/net/tlan.c:3038:6: warning: symbol 'TLan_MiiSync' was not declared. Should it be static?
drivers/net/tlan.c:3077:6: warning: symbol 'TLan_MiiWriteReg' was not declared. Should it be static?
drivers/net/tlan.c:3147:6: warning: symbol 'TLan_EeSendStart' was not declared. Should it be static?
drivers/net/tlan.c:3187:5: warning: symbol 'TLan_EeSendByte' was not declared. Should it be static?
drivers/net/tlan.c:3248:6: warning: symbol 'TLan_EeReceiveByte' was not declared. Should it be static?
drivers/net/tlan.c:3306:5: warning: symbol 'TLan_EeReadByte' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* If ConfigBase is 0x03c0 && manfid is (0x0149,0xc1ab),
printk "use axnet_cs instead" message.
Actually, most of the card with manfid(0x0149, 0xc1ab)
use pcnet_cs driver.
* remove entry (0x021b, 0x0202)
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Suppress the warning message about the 'netcard_portlist' defined but not used.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
