@verbose was added to ata_reset_fn_t because AHCI complained during
probing if no device was attached to the port. However, muting
failure message isn't the correct approach. Reset methods are
responsible for detecting no device condition and finishing
successfully. Now that AHCI softreset is fixed, kill @verbose.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.
Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the ATAPI_ENABLE_DMADIR compile time option needed
by some SATA-PATA bridge to runtime module parameter.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A lot of EH codes are about to be added to libata. Separate out
libata-eh.c. ata_scsi_timed_out(), ata_scsi_error(),
ata_qc_timeout(), ata_eng_timeout(), ata_eh_qc_complete() and
ata_eh_qc_retry() are moved. No code is changed by this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a new qc flag ATA_QCFLAG_IO. This flag gets set for normal IO
commands originating from SCSI midlayer. This information will be
used by EH to determine transfer speed reconfiguration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_configure() should not clear dynamic device flags determined
elsewhere. Lower eight bits are reserved for feature flags, define
ATA_DFLAG_CFG_MASK and clear only those bits before configuring
device. Without this patch, ATA_DFLAG_PIO gets turned off during
revalidation making PIO mode unuseable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename ATA_FLAG_PORT_DISABLED to ATA_FLAG_DISABLED for consistency.
(ATA_FLAG_* are always about ports).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Reorder ATA_DFLAG_* such that feature flags determined by
ata_dev_configure() are on lower bits. Reserve lower eight bits
for this purpose and allocate dynamic flags from bit 8.
* Reorder ATA_FLAG_* such that feature flags determined during driver
initiailization are on bits 0:15, dynamic flags on 16:23 and LLDD
specific flags on 24:31.
* Kill trailing white space and lower-case an one line comment for
consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve ata_bus_probe() such that configuration failures are handled
better. Each device is given ATA_PROBE_MAX_TRIES chances, but any
non-transient error (revalidation failure with -ENODEV, configuration
failure with -EINVAL...) disables the device directly. Any IO error
results in SATA PHY speed down and ata_set_mode() failure lowers
transfer mode. The last try always puts a device into PIO-0.
After each failure, the whole port is reset to make sure that the
controller and all the devices are in a known and stable state. The
reset also applies SATA SPD configuration if necessary.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap->sata_spd_limit contrains SATA PHY speed of the port. It is
initialized to the configured value prior to probing thus preserving
BIOS configured value. hardreset is responsible for applying SPD
limit and sata_std_hardreset() is updated to do that. SATA SPD limit
will be used to enhance failure handling during probing and later by
EH.
This patch also normalizes some comments around affected code.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For the time being we cannot use ata_dev_present() as it was renamed
to ata_dev_enabled() but we still need presence test. Implement
negation of the test. Conveniently, the negated result is needed in
more places. This is suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch renames ata_dev_present() to ata_dev_enabled() and adds
ata_dev_disabled(). This is to discern the state where a device is
present but disabled from not-present state. This disctinction is
necessary when configuring transfer mode because device selection
timing must not be violated even if a device fails to configure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core
This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.
Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is the minimal patch set to enable the current code to be used with
a controller following SFF (ie any PATA and early SATA controllers)
safely without crashes if there is no BMDMA area or if BMDMA is not
assigned by the BIOS for some reason.
Simplex status is recorded but not acted upon in this change, this isn't
a problem with the current drivers as none of them are for simplex
hardware. A following diff will deal with that.
The flags in the probe structure remain ->host_set_flags although Jeff
asked me to rename them, simply because the rename would break the usual
Linux rules that old code should break when there are changes. not
compile and run and then blow up/eat your computer/etc. Renaming this
later is a trivial exercise once a better name is chosen.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup the following unused functions:
- ata_pio_poll()
- ata_pio_complete()
- ata_pio_first_block()
- ata_pio_block()
- ata_pio_error()
ap->pio_task_timeout and other enums.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
E.D.D. has no user in-tree and mostly useless. Kill it. For possible
out-of-tree users, add a nice warning message and error handling if
LLDD doesn't report any useable reset mechanism (and thus tries to use
E.D.D.).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some of the dependence on the host_set struct
in preparation for supporting SAS HBAs. Adds a struct device
pointer to the ata_port struct.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At the moment libata doesn't pass pm_message_t down ata_device_suspend.
This causes drives to be powered down when we just want a freeze,
causing unnecessary wear and tear. This patch gets pm_message_t passed
down so that it can be used to determine whether to power down the
drive.
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
drivers/scsi/libata-core.c | 5 +++--
drivers/scsi/libata-scsi.c | 4 ++--
drivers/scsi/scsi_sysfs.c | 2 +-
include/linux/libata.h | 4 ++--
include/scsi/scsi_host.h | 2 +-
5 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add per-dev pio/mwdma/udma_mask. All transfer mode limits used to be
applied to ap->*_mask which unnecessarily restricted other devices
sharing the port. This change will also benefit later EH speed down
and hotplug.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
max_hw_sectors/max_sectors separation patch made into the tree,
increase max_sectors to its hardware limit.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add some dummy noop functions for use by libata clients
that do not need to do anything. Future SAS patches will
utilize these functions.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCSI midlayer has moved hostt->eh_timed_out to transport template. As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata. No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ATA_BITS_*, ATA_MASK_* macros and reorder xfer_mask fields such
that higher transfer mode is placed at higher order bit. As thie
reordering breaks ata_mode_string(), this patch also rewrites
ata_mode_string().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement port_task. LLDD's can schedule a function to be executed
with context after specified delay. libata core takes care of
synchronization against EH. This is generalized form of pio_task and
packet_task which are tied to PIO hsm implementation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_revalidate() re-reads IDENTIFY PAGE of the given device and
makes sure it's the same device as the configured one. Once it's
verified that it's the same device, @dev is configured according to
newly read IDENTIFY PAGE. Note that revalidation currently doesn't
invoke transfer mode reconfiguration.
Criteria for 'same device'
* same class (of course)
* same model string
* same serial string
* if ATA, same n_sectors (to catch geometry parameter changes)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_config() needs to be done everytime a device is configured.
Fold it into ata_dev_configure().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert dev->id from array to pointer. This is to accomodate
revalidation. During revalidation, both old and new IDENTIFY pages
should be accessible and single ->id array doesn't cut it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Seperate out ata_class_present() from ata_dev_present(). This is
useful because new reset mechanism deals with classes[] directly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes ata_for_each_sg() start with pad_sgent when
qc->n_elem is zero. Previously, ata_for_each_sg() unconditionally
started with qc->__sg, handling the first sg to fill_sg() routines
even when the entry was invalid. And while at it, unwind ?: in
ata_qc_next_sg() into if statement.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch renames ata_dev_id_[c_]string() to ata_id_[c_]string().
All other functions which read data from ATA ID data start with ata_id
and those two function names were getting too long.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If a low level driver wants to control max_sectors, it had to adjust
ap->host->max_sectors and set ATA_DFLAG_LOCK_SECTORS to tell
ata_scsi_slave_config not to override the limit. This is not only
cumbersome but also incorrect for hosts which support more than one
devices per port.
This patch adds per-device ->max_sectors. If the field is unset
(zero), libata core layer will adjust ->max_sectors according to
default rules. If the field is set, libata honors the setting.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
cdb_len is per-device property. Sharing cdb_len on ap results in
inaccurate configuration on revalidation and hotplugging. This patch
makes cdb_len per-device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ata_dev_id_c_string() reads ATA string from the specified offset of
the given IDENTIFY PAGE and puts it in the specified buffer in trimmed
and NULL-terminated form. The caller must supply a buffer which is
one byte larger than the maximum size of the target ID string.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch inlines ata_qc_complete() and uninlines __ata_qc_complete()
as suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement ata_scsi_timed_out(), to be used as
scsi_host_template->eh_timed_out callback for all libata drivers.
Without this function, the following race exists.
If a qc completes after SCSI timer expires but before libata EH kicks
in, the qc gets completed but the scsicmd still gets passed to libata
EH resulting in ->eng_timeout invocation with NULL qc, which none is
handling properly.
This patch makes sure that scmd and qc share the same lifetime.
Original idea from Jeff Garzik <jgarzik@pobox.com>.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add ATA_QCFLAG_EH_SCHEDULED. If this flag is set, the qc is owned by
EH and normal completion path is not allowed to finish it. This patch
doesn't actually use this flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements the off-the-shelf probeinit component operation.
Currently, all it does is waking up the PHY if it's a SATA port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds probeinit component operation to
ata_drive_probe_reset(). If present, this new operation is called
before performing any reset. The operations's roll is to prepare @ap
for following probe-reset operations.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes sure that pio tasks are flushed before proceeding
with EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ATA_FLAG_IN_EH flag is set on entry to EH and cleared on completion.
This patch just sets and clears the flag. Following patches will
build normal qc execution / EH synchronization aroung this flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement SRST, COMRESET and standard postreset component operations
for ata_drive_probe_reset(), and use these three functions to
implement ata_std_probe_reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Most low level drivers share supported reset/classify actions and
sequence. This patch implements ata_drive_probe_reset() which helps
constructing ->probe_reset from three component operations -
softreset, hardreset and postreset. This minimizes duplicate code and
yet allows flexibility if needed. The three component operations can
also be shared by EH later.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add new ->probe_reset operation to ata_port_operations obsoleting
->phy_reset. The main difference from ->phy_reset is that the new
operation is not allowed to manipulate libata internals directly.
It's not allowed to configure or disable the port or devices. It can
only succeed or fail and classify attached devices into passed
@classes.
This change gives more control to higher level and eases sharing reset
methods with EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Export ata_busy_sleep(), to be used by low level driver reset functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implement ata_eh_qc_complete/retry() using scsi_eh_finish_cmd() and
scsi_eh_flush_done_q(). This removes all eh scsicmd finish hacks from
low level drivers.
This change was first suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add detailed AC_ERR_* flags and use them. Long-term goal is to
describe all errors with err_mask and tf combination (tf for failed
sector information, etc...). After proper error diagnosis is
implemented, sense data should also be generated from err_mask instead
of directly from hardware tf registers as it is currently.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Return AC_ERR_* mask from issue fuctions instead of 0/-1. This
enables things like failing a qc with AC_ERR_HSM when the device
doesn't set DRDY when the qc is about to be issued.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
qc used to be freed automatically on command completion. However, as
a qc can carry information about its completion status, it can be
useful to its owner/issuer after command completion. This patch makes
freeing qc responsibility of its owner. This simplifies
ata_exec_internal() and makes command turn-around for atapi request
sensing less hackish.
This change was originally suggested by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds suspend patch to libata, and ata_piix in particular. For
most low level drivers, they should just need to add the 4 hooks to
work. As I can only test ata_piix, I didn't enable it for more
though.
Suspend support is the single most important feature on a notebook, and
most new notebooks have sata drives. It's quite embarrassing that we
_still_ do not support this. Right now, it's perfectly possible to
suspend the drive in mid-transfer.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some hardware does not support the PACKET command at all.
Other hardware supports ATAPI, but the driver does something nasty such
as calling BUG() when an ATAPI command is issued.
For these such cases, we mark them with a new flag, ATA_FLAG_NO_ATAPI.
Initial version contributed by Ben Collins.
There is no user of qc->waiting left after ata_exec_internal()
changes. Kill the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements ata_exec_internal() function which performs
libata internal command execution. Previously, this was done by each
user by manually initializing a qc, issueing it, waiting for its
completion and handling errors. In addition to obvious code
factoring, using ata_exec_internal() fixes the following bugs.
* qc not freed on issue failure
* ap->qactive clearing could race with the next internal command
* race between timeout handling and irq
* ignoring error condition not represented in tf->status
Also, qc & hardware are not accessed anymore once it's completed,
making internal commands more conformant with general semantics.
ata_exec_internal() also makes it easy to issue internal commands from
multiple threads if that becomes necessary.
This patch only implements ata_exec_internal(). A following patch
will convert all users.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, all patches have been regenerated against upstream branch as of
today. (575ab52a21)
Also, I took out a debug printk from ata_exec_internal (don't know how
that one got left there). Other than that, all patches are identical
to the previous posting.
Thanks. :-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- remove err_mask from the parameter list of the complete functions
- move err_mask to ata_queued_cmd
- initialize qc->err_mask when needed
- for each function call to ata_qc_complete(), replace the err_mask parameter with qc->err_mask.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
===============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- in ata_dev_identify(), don't assume that all devices are either
ATA or ATAPI. In the future, this code will see port multipliers
and other devices.
- make a debugging printk less verbose
- add new helper ata_qc_reinit()
- add new helper BPRINTK() and port flag ATA_FLAG_DEBUGMSG, for
fine-grained debugging use.
This will let me chop the code size of several drivers right down. In
many cases the actual private data is very useful and constant for a
given host controller so being able to just pass it at probe time would
be very useful indeed (eg with the via driver would could pass the udma
clocking and reduce the code size, or with the AMD one the UDMA
multiplier and the offset)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On Alpha:
include/linux/libata.h: In function `ata_pad_alloc':
include/linux/libata.h:785: warning: implicit declaration of function `dma_alloc_coherent'
include/linux/libata.h:786: warning: assignment makes pointer from integer without a cast
include/linux/libata.h: In function `ata_pad_free':
include/linux/libata.h:792: warning: implicit declaration of function `dma_free_coherent'
(I have a decouple-some-header-files cleanup in -mm, so it's causing some
fallout of this nature)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- remove ap->dataout_task from struct ata_port
- let ata_pio_task() handle the HSM_ST_FIRST state.
- rename ata_dataout_task() to ata_pio_first_block()
- replace the ata_dataout_task workqueue with ata_pio_task workqueue
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
========
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use ata_pad_{alloc,free} in two drivers, to factor out common code.
Add ata_pad_{alloc,free} to two other drivers, which needed the padding
but had not been updated.
The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error. On legacy PCI IDE hardware, the latter
is often implicit in the former. On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.
Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.
This will lead to more flexible error handling in the future.
This is needed for full AMD and VIA drivers and possibly more. Functions
to turn actual clocking and cycle timings into register values. Also to
merge shared timings to compute an optimal timing set.
Built from the drivers/ide version by Vojtech Pavlik
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This redoes the n_ports logic I proposed before as a bitmask.
ata_pci_init_native_mode is now used with a mask allowing for mixed mode
stuff later on. ata_pci_init_legacy_port is called with port number and
does one port now not two. Instead it is called twice by the ata init
logic which cleans both of them up.
There are stil limits in the original code left over
- IRQ/port mapping for legacy mode should be arch specific values
- You can have one legacy mode IDE adapter per PCI root bridge on some systems
- Doesn't handle mixed mode devices yet (but is now a lot closer to it)
libata.h:
libata-core:
Add ATA_FLAG_PIO_POLLING flag for LLDs that expect interrupt for
command completion only.
sata_nv.c:
sata_vsc.c:
irq handler is wrapper around ata_host_intr(), can handle PIO interrupts.
sata_promise.c:
sata_sx4.c:
sata_qstor.c:
sata_mv.c:
Private irq handler.
Polling mode ATA_FLAG_PIO_POLLING used for compatibility.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add PIO_ST_FIRST for the state before sending ATAPI CDB or sending
"ATA PIO data out" first data block.
- add ATA_TFLAG_POLLING and ATA_DFLAG_CDB_INTR flags
- remove the ATA_FLAG_NOINTR flag since the interrupt handler is now
aware of the states
- modify ata_pio_sector() and atapi_pio_bytes() to work in the interrupt
context
- modify the ata_host_intr() to handle PIO interrupts
- modify ata_qc_issue_prot() to initialize states
- atapi_packet_task() changed to handle "ATA PIO data out" first data block
- support the pre-ATA4 ATAPI device which raise interrupt when ready to
receive CDB
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Changes:
s/PIO_ST_/HSM_ST_/ and s/pio_task_state/hsm_task_state/.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ATAPI is getting close to being ready. To increase exposure, we enable
the code in the upstream kernel, but default it to off (present
behavior). Users must pass atapi_enabled=1 as a module option (if
module) or on the kernel command line (if built in) to turn on
discovery of their ATAPI devices.
- changes license of all code from OSL+GPL to plain ole GPL
- except for NVIDIA, who hasn't yet responded about sata_nv
- copyright holders were already contacted privately
- adds info in each driver about where hardware/protocol docs may be
obtained
- where I have made major contributions, updated copyright dates
Interrupts from devices sharing the same IRQ could cause
ata_host_intr to finish commands being processed by atapi_packet_task
if the commands are using ATA_PROT_ATAPI_NODATA or ATA_PROT_ATAPI_DMA
protocol. This is because libata interrupt handler is unaware that
interrupts are not expected during that period. This patch adds
ATA_FLAG_NOINTR flag to tell the interrupt handler that we're not
expecting interrupts.
Note that once proper HSM is implemented for interrupt-driven PIO,
this should be merged into it and this flag will be removed.
ahci.c is a different kind of beast, so it's left alone.
* The following drivers use ata_qc_issue_prot and ata_interrupt, so
changes in libata core will do.
ata_piix sata_sil sata_svw sata_via sata_sis sata_uli
* The following drivers use ata_qc_issue_prot and custom intr handler.
They need this change to work correctly.
sata_nv sata_vsc
* The following drivers use custom issue function and intr handler.
Currently all custom issue functions don't support ATAPI, so this
change is irrelevant, updated for consistency and to avoid later
mistakes.
sata_promise sata_qstor sata_sx4
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
