Rename for_each_bit to for_each_set_bit in the kernel source tree. To
permit for_each_clear_bit(), should that ever be added.
The patch includes a macro to map the old for_each_bit() onto the new
for_each_set_bit(). This is a (very) temporary thing to ease the migration.
[akpm@linux-foundation.org: add temporary for_each_bit()]
Suggested-by: Alexey Dobriyan <adobriyan@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
IB/srp: Clean up error path in srp_create_target_ib()
IB/srp: Split send and recieve CQs to reduce number of interrupts
RDMA/nes: Add support for KR device id 0x0110
IB/uverbs: Use anon_inodes instead of private infinibandeventfs
IB/core: Fix and clean up ib_ud_header_init()
RDMA/cxgb3: Mark RDMA device with CXIO_ERROR_FATAL when removing
RDMA/cxgb3: Don't allocate the SW queue for user mode CQs
RDMA/cxgb3: Increase the max CQ depth
RDMA/cxgb3: Doorbell overflow avoidance and recovery
IB/core: Pack struct ib_device a little tighter
IB/ucm: Clean whitespace errors
IB/ucm: Increase maximum devices supported
IB/ucm: Use stack variable 'base' in ib_ucm_add_one
IB/ucm: Use stack variable 'devnum' in ib_ucm_add_one
IB/umad: Clean whitespace
IB/umad: Increase maximum devices supported
IB/umad: Use stack variable 'base' in ib_umad_init_port
IB/umad: Use stack variable 'devnum' in ib_umad_init_port
IB/umad: Remove port_table[]
IB/umad: Convert *cdev to cdev in struct ib_umad_port
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (214 commits)
omap2: Initialize Menelaus and MMC for N8X0
AM3517 EVM: correct typo - tca6416 mispelt as tca6516
AM3517 EVM: Enable I2C support
AM35x: Enable OMAP_MUX in defconfig
AM35x: Add missing GPIO mux config for EHCI port
Zoom3: Defconfig update
omap: i2c: Fix muxing for command line enabled bus
OMAP4: clock: Remove clock hacks from timer-gp.c
OMAP4: clock: Add dummy clock nodes for interface clocks
OMAP4: clock: Rename leaf clock nodes to end with a _ick or _fck
OMAP2+ clock: revise omap2_clk_{disable,enable}()
OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change code
OMAP clockdomain: if no autodeps exist, don't try to add or remove them
OMAP hwmod: add hwmod class support
OMAP hwmod: convert header files with static allocations into C files
OMAP hwmod: convert hwmod to use hardware clock names rather than clkdev dev+con
OMAP clock: add omap_clk_get_by_name() for use by OMAP hwmod core code
OMAP3: clock: add capability to change rate of dpll4_m5_ck_3630
OMAP4 clock: drop the ALWAYS_ENABLED clock flag
OMAP clock: drop RATE_FIXED clock flag
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
virtio_net: remove forgotten assignment
be2net: fix tx completion polling
sis190: fix cable detect via link status poll
net: fix protocol sk_buff field
bridge: Fix build error when IGMP_SNOOPING is not enabled
bnx2x: Tx barriers and locks
scm: Only support SCM_RIGHTS on unix domain sockets.
vhost-net: restart tx poll on sk_sndbuf full
vhost: fix get_user_pages_fast error handling
vhost: initialize log eventfd context pointer
vhost: logging thinko fix
wireless: convert to use netdev_for_each_mc_addr
ethtool: do not set some flags, if others failed
ipoib: returned back addrlen check for mc addresses
netlink: Adding inode field to /proc/net/netlink
axnet_cs: add new id
bridge: Make IGMP snooping depend upon BRIDGE.
bridge: Add multicast count/interval sysfs entries
bridge: Add hash elasticity/max sysfs entries
bridge: Add multicast_snooping sysfs toggle
...
Trivial conflicts in Documentation/feature-removal-schedule.txt
This is no longer needed. I missed to remove this in
567ec874d1 ("net: convert multiple
drivers to use netdev_for_each_mc_addr, part6")
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sis190 devices don't report LinkChange, so do polling for
link status.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11926
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
DaVinci DM365: Adding support for SPI EEPROM
DaVinci DM365: Adding DM365 SPI support
DaVinci DM355: Modifications to DM355 SPI support
DaVinci: SPI: Adding header file for SPI support.
davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
DaVinci: DM365: Voice codec support for the DM365 SoC
davinci: clock: let clk->set_rate function sleep
Add SDA and SCL pin numbers to i2c platform data
davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
davinci: build list of unused EDMA events dynamically
davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
davinci: Keep count of channel controllers on a platform
davinci: Correct return value of edma_alloc_channel api
davinci: add CDCE949 support on DM6467 EVM
davinci: add support for CDCE949 clock synthesizer
davinci: da850/omap-l138 EVM: register for suspend support
davinci: da850/omap-l138: add support for SoC suspend
davinci: add power management support
DaVinci: DM365: Changing default queue for DM365.
...
[Resending with the proper subject. Sorry for the mess. ]
This patch is based on the RFC of Stanislaw Gruszka.
More specifically it fixes two possible races:
- One, described by Stanislaw, may lead to permanent disabling of the Tx
queue.
This is fixed by adding the smp_wmb() to propagate the BD consumer
change towards the memory.
- Second may lead to bnx2x_start_xmit() returning NETDEV_TX_BUSY.
This is fixed by taking a tx_lock() before rechecking the number of
available Tx BDs.
thanks,
vlad
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VPD searching code is abstracted away, the outer loop used
to detect the read-only large resource data type section is useless.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VPD searching code is abstracted away, the outer loop used
to detect the read-only large resource data type section is useless.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_info_keyword() helper function to
find information field keywords within read-only and read-write large
resource data type sections.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a preprocessor constant to describe the PCI VPD
information field header size and an inline function to extract the
size of the information field itself.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_tag() helper function to find VPD
resource data types in a buffer.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces more VPD preprocessor definitions to identify some
small and large resource data type item names. The patch then continues
to correct how the tg3 and bnx2 drivers search for the "read-only data"
large resource data type.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a preprocessor constant to describe the PCI VPD large
resource data type tag size and an inline function to extract the large
resource section size from the large resource data type tag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move platform device code from the drivers to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch makes the ar7 clock code implement the Linux clk API. Drivers
using the various clocks available in the SoC are updated accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
To: linux-mips@linux-mips.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: netdev@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the au1000-eth driver to become a full platform-driver
as it ought to be. We now pass PHY-speficic configurations through
platform_data but for compatibility the driver still assumes the default
settings (search for PHY1 on MAC0) when no platform_data is passed. Tested
on my MTX-1 board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/619/
Patchwork: http://patchwork.linux-mips.org/patch/963/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move TC_PRIO_CONTROL check and queue remapping into
ixgbe_select_queue(). Remapping queues after the qdisc
can result in the wrong qdisc queue being stopped with
netif_stop_subqueue(). Even if this is resolved and the
correct queue is stopped it can result in a queue being
blocked by TC_PRIO_CONTROL frames uneccesarily. Moving
this into the select_queue routine maintains alignment
between tx_rings and qdisc queues.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the register_netdevice() call fails, the newly allocated device is
not freed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e8469ed959c373c2ff9e6f488aa5a14971aebe1f
Author: Patrick McHardy <kaber@trash.net>
Date: Tue Feb 23 20:41:30 2010 +0100
Support specifying the initial device flags when creating a device though
rtnl_link. Devices allocated by rtnl_create_link() are marked as INITIALIZING
in order to surpress netlink registration notifications. To complete setup,
rtnl_configure_link() must be called, which performs the device flag changes
and invokes the deferred notifiers if everything went well.
Two examples:
# add macvlan to eth0
#
$ ip link add link eth0 up allmulticast on type macvlan
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether 26:f8:84:02:f9:2a brd ff:ff:ff:ff:ff:ff
[ROUTE]ff00::/8 dev macvlan0 table local metric 256 mtu 1500 advmss 1440 hoplimit 0
[ROUTE]fe80::/64 dev macvlan0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500
link/ether 26:f8:84:02:f9:2a
[ADDR]11: macvlan0 inet6 fe80::24f8:84ff:fe02:f92a/64 scope link
valid_lft forever preferred_lft forever
[ROUTE]local fe80::24f8:84ff:fe02:f92a via :: dev lo table local proto none metric 0 mtu 16436 advmss 16376 hoplimit 0
[ROUTE]default via fe80::215:e9ff:fef0:10f8 dev macvlan0 proto kernel metric 1024 mtu 1500 advmss 1440 hoplimit 0
[NEIGH]fe80::215:e9ff:fef0:10f8 dev macvlan0 lladdr 00:15:e9:f0:10:f8 router STALE
[ROUTE]2001:6f8:974::/64 dev macvlan0 proto kernel metric 256 expires 0sec mtu 1500 advmss 1440 hoplimit 0
[PREFIX]prefix 2001:6f8:974::/64 dev macvlan0 onlink autoconf valid 14400 preferred 131084
[ADDR]11: macvlan0 inet6 2001:6f8:974:0:24f8:84ff:fe02:f92a/64 scope global dynamic
valid_lft 86399sec preferred_lft 14399sec
# add VLAN to eth1, eth1 is down
#
$ ip link add link eth1 up type vlan id 1000
RTNETLINK answers: Network is down
<no events>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC5121 FEC requeries 4-byte alignmnent for TX data buffers.
This patch is a work around that copies misaligned tx packets
to an aligned skb before sending.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the fs_enet driver to support MPC512x FEC.
Enable it with CONFIG_FS_ENET_MPC5121_FEC option.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the b43 driver just automatically fall back to PIO mode when
DMA doesn't work.
The driver already told the user to do it, so rather than have the user
reload the module with a new flag, just make the driver do it
automatically. We keep the message as an indication that something is
wrong, but now just automatically fall back to the hopefully working PIO
case.
(Some post-2.6.33 merge fixups by Larry Finger <Larry.Finger@lwfinger.net>
and yours truly... -- JWL)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While ath9k does not support RIFS yet, the ability to receive RIFS
frames is currently enabled for most chipsets in the initvals.
This is causing baseband related issues on AR9160 and AR9130 based
chipsets, which can lock up under certain conditions.
This patch fixes these issues by overriding the initvals, effectively
disabling RIFS for all affected chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ISA skeleton net driver has been obsolete and unmaintained for many
years. Any hardware remotely like ISA will use the platform API and
look much more like a PCI driver, and make much better use of netdev
APIs such as NAPI.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAN module on AM3517 requires programming of IO expander as part
of init sequence - to enable CAN PHY. Added platform specific
callback to handle phy control(switch on /off).
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There doesn't seem to be any reason to explicitly return
NETDEV_TX_OK as err is set to NETDEV_TX_OK in all cases that
reach this point.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small optimization to the code which checks to see if we'd cross
a 4K boundary when stocking RX ring.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Guillaume Morin <guillaume@morinfr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to assign the status block address once and it also saves
space in the structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a separate IP address for iSCSI, connections should proceed
whether or not we can get a route to the target from the network stack.
It is possible that the network IP address may not reach the iSCSI target.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some data structures are freed when the device is down and it will
crash if an ISCSI netlink message is received. Add RCU protection
to prevent this. In the shutdown path, ulp_ops[CNIC_ULP_L4] is
assigned NULL and rcu_synchronized before freeing the data
structures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For bnx2 devices, always send notification to bnx2i to let it initiate
the cleanup when RST is received.
For bnx2x devices, add unsolicited RST_COMP handling to start the cleanup.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize IP ID and handle some additional connection errors.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating 128 struct netdev_queue per device, use the
minimum value between 128 and the number of possible txq's, to
reduce ram usage and "tc -s -d class shod dev .." output.
This patch fixes Eric Dumazet's patch to set the TX queues to
the correct minimum.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
