This matters to any sort of device that is wired to one of the CPU
interrupt pins on an SMP system. Typically the scenario is most easily
triggered with the count/compare timer interrupt where the same interrupt
number and thus irq_desc is used on each processor.
CPU A CPU B
do_IRQ()
generic_handle_irq()
handle_level_irq()
spin_lock(desc_lock)
set IRQ_INPROGRESS
spin_unlock(desc_lock)
do_IRQ()
generic_handle_irq()
handle_level_irq()
spin_lock(desc_lock)
IRQ_INPROGRESS set => bail out
spin_lock(desc_lock)
clear IRQ_INPROGRESS
spin_unlock(desc_lock)
In case of the cp0 compare interrupt this means the interrupt will be
acked and not handled or re-armed on CPU b, so there won't be any timer
interrupt until the count register wraps around.
With kernels 2.6.20 ... 2.6.23 we usually were lucky that things were just
working right on VSMP because the count registers are synchronized on
bootup so it takes something that disables interrupts for a long time on
one processor to trigger this one.
For scenarios where an interrupt is multicasted or broadcasted over several
CPUs the existing code was safe and the fix will break it. There is no
way to know in the interrupt controller code because it is abstracted from
the platform code. I think we do not have such a setup currently, so this
should be ok.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GNU `config.guess' uses "linux-gnu" as the canonical system name.
Fix the list of compiler prefixes checked to spell it correctly.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds a JR.HB after halting a TC, to ensure that the TC has really halted.
only modifies the TCSTATUS register when the TC is safely halted.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have no guarantee by the generic time code that the timer is stopped
when the ->next_event method is called. Modifying the Timer Initial Count
register while the timer is enabled has UNPREDICTABLE effect according to
the BCM1250/BCM1125/BCM1125H User Manual. So stop the timer before
reprogramming.
This is a paranoia fix; no ill effects have been observed previously.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the old minimum of a single tick a value of zero would be programmed
into the init value register which in the BCM1250/BCM1125/BCM1125H User
Manual in the Timer Special Cases section is documented to have
UNPREDICTABLE effect.
Observable sympthoms of this bug were hangs of several seconds on the
console during bootup and later if both dyntick and highres timer options
were activated.
In theory contiguous mode of the timers is also affected but in an act of
hopeless lack of realism I'll assume nobody will ever configure a KERNEL
for HZ > 500kHz but if so I leave that to evolution to sort out.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The range of MIPS_CPU IRQ and the range of LASAT IRQ overlap.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Shadow register support would not possibly have worked on multicore
systems. The support code for it was also depending not on MIPS R2 but
VSMP or SMTC kernels even though it makes perfect sense with UP kernels.
SR sets are a scarce resource and the expected usage pattern is that
users actually hardcode the register set numbers in their code. So fix
the allocator by ditching it. Move the remaining CPU probe bits into
the generic CPU probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
iounmap if pci clock is over 33MHz. Cosmetic because the iomap() in this
case is just a bit of address magic.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The recent switch of the Sibyte SOCs from the processor specific cache
managment code in c-sb1.c to c-r4k.c lost this old hack
[MIPS] Hack for SB1 cache issues
Removing flush_icache_page a while ago broke SB1 which was using an empty
flush_data_cache_page function. This glues things well enough so a more
efficient but also more intrusive solution can be found later.
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
in the hope it was no longer needed. As it turns it still is so resurrect
it until there is a better solution.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Jazz machines have to use the PIT timer for dyntick and highresolution
kernels. This may break because currently just like i386 used to do MIPS
uses two separate spinlocks in the actual PIT code and the PC speaker
code. So switch to do it the same that x86 currently does PIT locking.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix ISA irq acknowledge.
Make r4030 clockevent code look like other mips clockevent code.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register A20R clockevent.
Remove PIT timer setup because it doesn't work
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/au1000/pb1200/irqmap.c:101: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
And while at it a few coding style cleanups.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Do not include unnecessary headers.
* Do not mention time.README.
* Do not mention mips_timer_ack.
* Make clocksource_mips static. It is now dedicated to c0_timer.
* Initialize clocksource_mips.read statically.
* Remove null_hpt_read.
* Remove an argument of plat_timer_setup. It is just a placeholder.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When GDB writes a breakpoint into address area of inferior process the
kernel needs to invalidate the modified memory in the inferior which
is done by calling flush_cache_page which in turns calls
r4k_flush_cache_page and local_r4k_flush_cache_page for VSMP or SMTC
kernel via r4k_on_each_cpu().
As the VSMP and SMTC SMP kernels for 34K are running on a single shared
caches it is possible to get away without interprocessor function calls.
This optimization is implemented in r4k_on_each_cpu, so
local_r4k_flush_cache_page is only ever called on the local CPU.
This is where the following code in local_r4k_flush_cache_page() strikes:
/*
* If ownes no valid ASID yet, cannot possibly have gotten
* this page into the cache.
*/
if (cpu_context(smp_processor_id(), mm) == 0)
return;
On VSMP and SMTC had a function of cpu_context() for each CPU(TC).
So in case another CPU than the CPU executing local_r4k_cache_flush_page
has not accessed the mm but one of the other CPUs has there may be data
to be flushed in the cache yet local_r4k_cache_flush_page will falsely
return leaving the I-cache inconsistent for the breakpoint.
While the issue was discovered with GDB it also exists in
local_r4k_flush_cache_range() and local_r4k_flush_cache().
Fixed by introducing a new function has_valid_asid which on MT kernels
returns true if a mm is active on any processor in the system.
This is relativly expensive since for memory acccesses in that loop
cache misses have to be assumed but it seems the most viable solution
for 2.6.23 and older -stable kernels.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable the onboard GenBus IDE interface in the default configuration.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Contrary to the belief of some, the R3000 and related processors did have
caches, both a data and an instruction cache. Here is an implementation
of r3k_flush_cache_page(), which is the processor-specific back-end for
flush_cache_range(), done according to the spec in
Documentation/cachetlb.txt.
While at it, remove an unused local function: get_phys_page(), do some
trivial formatting fixes and modernise debugging facilities.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A comment on ptrace_getregs() states "Registers are sign extended to
fill the available space." but it is not true. Fix code to match the
comment. Also fix casts on each caller to get rid of some warnings.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch separates the platform devices registration for the MTX-1
specific devices: GPIO leds and watchdog.
[Minor fixup and formatting change -- Ralf]
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mmap with MAP_FIXED was not validating the addr and len parameters. This
leads to the failure of GCC's gcc.c-torture/execute/loop-2[fg].c testcases
when using the o32 ABI on a 64 bit kernel.
These testcases try to mmap 65536 bytes at 0x7fff8000 and then access all
the memory. In 2.6.18 and 2.6.23.1 (and likely other versions as well)
the kernel maps the requested memory, but since half of it is above
0x80000000 a SIGBUS is generated when it is accessed.
This patch moves the len validation above the MAP_FIXED processing so that
it is always validated. It also adds validation to the addr parameter for
MAP_FIXED mappings.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try increasingly longer time periods starting of at 0x10 cycles. This
should be fast on hardware and work nicely with emulators.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The expression "(long)(read_c0_count() - cnt)" can never be a negative
value on 64-bit kernel. Cast to "int" before comparison.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They break the timer interrupt initialization and only seem to be a kludge
for initialization happening in the wrong order. Further testing done by
Thiemo confirms the suspicion that the other invocations also seem to have
useless.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert jmr3927_clock_event_device to more generic
txx9tmr_clock_event_device which supports one-shot mode. The
txx9tmr_clock_event_device can be used for TX49 too if the cp0 timer
interrupt was not available.
Convert jmr3927_hpt_read to txx9_clocksource driver which does not
depends jiffies anymore. The txx9_clocksource itself can be used for
TX49, but normally TX49 uses higher precision clocksource_mips.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixme: At the time of this writing cevt-r4k.c doesn't yet know about how
to handle the alternate timer interrupt of the RM9000.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the cp0 compare interrupt handler isn't initialized by the time
plat_time_init is called don't set IE_IRQ5 anymore, cevt-r4k.c will do
that a little later itself.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The old plat_timer_setup hook is no longer getting called so the Alchemy
time initialization was getting skipped.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
clockevent_delta2ns() use the shift and mult value, so
clockevent_set_clock() should be called first.
Pointed out by Atsushi Nemoto.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
set_next_event() and set_mode() are always called with interrupt disabled.
irqsave and irqrestore are not necessary for spinlock.
Pointed out by Atsushi Nemoto.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Modify the SMTC initialization code to allow boot-time specification not
only of how many VPEs and TCs to use, but also how many TCs out of the
allowed pool are to be bound to VPE 0. The new boot option is "vpe0tcs=N",
where N is an integer. Using it in combination with the existing options
allows arbitrary assignments across the 2 VPEs of a 34K. e.g. "maxtcs=3
vpe0tcs=1" forces VPE0 to have 1 TC, while VPE1 has 2, and "maxtcs=4
vpe0tcs=3" forces VPE0 to have 3 TCs, while VPE1 gets 1. If no vpe0tcs
option is specified, the traditional algorithm of evenly dividing TCs
between available VPEs, with the odd "slop" going to VPE0, is retained.
The reason for doing this is to allow a finer balancing of TCs which can
handle I/O interrupts on Malta (those on VPE 0) and those which cannot.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] time: Make c0_compare_int_usable more bullet proof
[MIPS] Kbuild: Use the new cc-cross-prefix feature.
[MIPS] Fix include wrapper symbol to something sane.
[MIPS] Malta: Delete dead code.
[MIPS] time: Add GT641xx timer0 clockevent driver
[MIPS] time: SMP-proofing of Sibyte clockevent/clocksource code.
[MIPS] time: SMP/NUMA-proofing of IP27 HUB RT timer code.
[MIPS] time: Fix calculation in clockevent_set_clock()
And make use of it for Cobalt. A few others such as the Malta could make
use of it as well.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The BCM148 has 4 cores but there are also just 4 generic timers available
so use the ZBbus cycle counter instead of it. In addition the ZBbus
counter also offers a much higher resolution and 64-bit counting so I'm
considering a later complete conversion to it once I figure out if all
members of the Sibyte SOC family support it - the docs seem to agree but
the headers files seem to disagree ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Delete totally outdated Documentation/mips/time.README
[MIPS] Kill duplicated setup_irq() for cp0 timer
[MIPS] Sibyte: Finish conversion to modern time APIs.
[MIPS] time: Helpers to compute clocksource/event shift and mult values.
[MIPS] SMTC: Build fix.
[MIPS] time: Delete dead code.
[MIPS] MIPSsim: Strip defconfig file to the bones.
Quoting Randy:
"It seems sad that this patch sources Kconfig.marker, a 7-line file,
20-something times. Yes, you (we) don't want to put those 7 lines into
20-something different files, so sourcing is the right thing.
However, what you did for avr32 seems more on the right track to me: make
_one_ Instrumentation support menu that includes PROFILING, OPROFILE, KPROBES,
and MARKERS and then use (source) that in all of the arches."
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the easiest things to isolate is the pid printed in kernel log.
There was a patch, that made this for arch-independent code, this one makes
so for arch/xxx files.
It took some time to cross-compile it, but hopefully these are all the
printks in arch code.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
is_init() is an ambiguous name for the pid==1 check. Split it into
is_global_init() and is_container_init().
A cgroup init has it's tsk->pid == 1.
A global init also has it's tsk->pid == 1 and it's active pid namespace
is the init_pid_ns. But rather than check the active pid namespace,
compare the task structure with 'init_pid_ns.child_reaper', which is
initialized during boot to the /sbin/init process and never changes.
Changelog:
2.6.22-rc4-mm2-pidns1:
- Use 'init_pid_ns.child_reaper' to determine if a given task is the
global init (/sbin/init) process. This would improve performance
and remove dependence on the task_pid().
2.6.21-mm2-pidns2:
- [Sukadev Bhattiprolu] Changed is_container_init() calls in {powerpc,
ppc,avr32}/traps.c for the _exception() call to is_global_init().
This way, we kill only the cgroup if the cgroup's init has a
bug rather than force a kernel panic.
[akpm@linux-foundation.org: fix comment]
[sukadev@us.ibm.com: Use is_global_init() in arch/m32r/mm/fault.c]
[bunk@stusta.de: kernel/pid.c: remove unused exports]
[sukadev@us.ibm.com: Fix capability.c to work with threaded init]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Herbert Poetzel <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The set of functions process_session, task_session, process_group and
task_pgrp is confusing, as the names can be mixed with each other when looking
at the code for a long time.
The proposals are to
* equip the functions that return the integer with _nr suffix to
represent that fact,
* and to make all functions work with task (not process) by making
the common prefix of the same name.
For monotony the routines signal_session() and set_signal_session() are
replaced with task_session_nr() and set_task_session(), especially since they
are only used with the explicit task->signal dereference.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In pre-cgroup cpusets, a few config files enabled cpusets by default.
Signed-off-by: Paul Jackson <pj@sgi.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cycles_per_jiffy was only ever getting assigned and the function pointer
not being called anymore and mips_timer_ack had gotten similarly stale. I
leave the remaining assignments unfixed as a lighthouse pointing platform
maintainers to what needs a rewrite. These changes make null_timer_ack()
unreferenced, so delete that too.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Always jump to the place where the kernel is linked to. This helps where
the bootloaders/proms ignores the start address inside the ELF header.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As IP22 is now using do_IRQ for timer interrupt, don't mess with
interrupt handler any longer
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some processors offer the option of using the interrupt on which
normally the count / compare interrupt would be signaled as a normal
interupt pin. Previously this required some ugly hackery for each
system which is much easier done by a quick and simple probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Userland, including the C library and the dynamic linker, is keen to use
the SYNC instruction, even for "generic" MIPS I binaries these days.
Which makes it less than useful on MIPS I processors.
This change adds the emulation, but as our do_ri() infrastructure was not
really prepared to take yet another instruction, I have rewritten it and
its callees slightly as follows.
Now there is only a single place a possible signal is thrown from. The
place is at the end of do_ri(). The instruction word is fetched in
do_ri() and passed down to handlers. The handlers are called in sequence
and return a result that lets the caller decide upon further processing.
If the result is positive, then the handler has picked the instruction,
but a signal should be thrown and the result is the signal number. If the
result is zero, then the handler has successfully simulated the
instruction. If the result is negative, then the handler did not handle
the instruction; to make it more obvious the calls do not follow the usual
0/-Exxx result convention they now return -1 instead of -EFAULT.
The calculation of the return EPC is now at the beginning. The reason is
it is easier to handle it there as emulation callees may modify a register
and an instruction may be located in delay slot of a branch whose result
depends on the register. It has to be undone if a signal is to be raised,
but it is not a problem as this is the slow-path case, and both actions
are done in single places now rather than the former being scattered
through emulation handlers.
The part of do_cpu() being covered follows the changes to do_ri().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Remove the old-fashioned lk201 driver under drivers/tc/ that used to be
used by the old dz.c and zs.c drivers, which is now orphan code referred to
from nowhere and does not build anymore. A modern replacement is available
as drivers/input/keyboard/lkkbd.c.
There are no plans to do anything about this piece of code and it does not
fit anywhere anymore, so it is not just a matter of maintenance or the lack
of. There are still some bits that might be added to the new lkkbd.c
driver based on the old code, and the embedded hardware documentation which
is otherwise quite hard to get hold of might be useful to keep too. Both
of these can be done separately though. RIP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_cache_(wback|inv|wback_inv) were the earliest attempt on a generalized
cache managment API for I/O purposes. Originally it was basically the raw
MIPS low level cache API exported to the entire world. The API has
suffered from a lack of documentation, was not very widely used unlike it's
more modern brothers and can easily be replaced by dma_cache_sync. So
remove it rsp. turn the surviving bits back into an arch private API, as
discussed on linux-arch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All asm/ipc.h files do only #include <asm-generic/ipc.h>.
This patch therefore removes all include/asm-*/ipc.h files and moves the
contents of include/asm-generic/ipc.h to include/linux/ipc.h.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some time /proc/sys/kernel/core_pattern has been able to set its output
destination as a pipe, allowing a user space helper to receive and
intellegently process a core. This infrastructure however has some
shortcommings which can be enhanced. Specifically:
1) The coredump code in the kernel should ignore RLIMIT_CORE limitation
when core_pattern is a pipe, since file system resources are not being
consumed in this case, unless the user application wishes to save the core,
at which point the app is restricted by usual file system limits and
restrictions.
2) The core_pattern code should be able to parse and pass options to the
user space helper as an argv array. The real core limit of the uid of the
crashing proces should also be passable to the user space helper (since it
is overridden to zero when called).
3) Some miscellaneous bugs need to be cleaned up (specifically the
recognition of a recursive core dump, should the user mode helper itself
crash. Also, the core dump code in the kernel should not wait for the user
mode helper to exit, since the same context is responsible for writing to
the pipe, and a read of the pipe by the user mode helper will result in a
deadlock.
This patch:
Remove the check of RLIMIT_CORE if core_pattern is a pipe. In the event that
core_pattern is a pipe, the entire core will be fed to the user mode helper.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: <martin.pitt@ubuntu.com>
Cc: <wwoods@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch single-linked binfmt formats list to usual list_head's. This leads
to one-liners in register_binfmt() and unregister_binfmt(). The downside
is one pointer more in struct linux_binfmt. This is not a problem, since
the set of registered binfmts on typical box is very small -- (ELF +
something distro enabled for you).
Test-booted, played with executable .txt files, modprobe/rmmod binfmt_misc.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Increase cp0 compare clockevent min_delta_ns from 0x30 to 0x300.
[MIPS] Cache: Provide more information on cache policy on bootup.
[MIPS] Fix aliasing bug in copy_user_highpage, take 2.
[MIPS] VPE loader: convert from struct class_ device to struct device
[MIPS] MIPSsim: Fix booting from NFS root
[MIPS] Alchemy: Get rid of au1xxx_irq_map_t.
[MIPS] Alchemy: Get rid of au_ffz().
[MIPS] Alchemy: Get rid of au_ffs().
[MIPS] Alchemy: cleanup interrupt code.
[MIPS] Lasat: Fix build by conversion to irq_cpu.c.
[MIPS] Lasat: Add #ifndef ... #endif include warpper to lasatint.h.
[MIPS] IP22: Enable -Werror.
[MIPS] IP22: Fix warning.
[MIPS] IP22: Complain if requesting the front panel irq failed.
[MIPS] vmlinux.lds.S: Handle KPROBES_TEXT.
[MIPS] vmlinux.lds.S: Fix handling of .notes in final link.
[MIPS] vmlinux.lds.S: Remove duplicate comment.
[MIPS] MSP71XX: Add workarounds file.
[MIPS] IP32: Fix build by conversion to irq_cpu.c.
Extremly low values are of dubious usefulness anyway but in this case
they actually were killing Qemu which simply wasn't able to complete
mips_next_event() within 0x30 100MHz cycles even on fast hosts.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should help making bug reports for the gadzillion of cores with all
their configuration and synthesis options more useful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Turns out b868868ae0 wasn't quite right.
When called for a page that isn't marked dirty it would artificially
create an alias instead of doing the obvious thing and access the page
via KSEG0.
The same issue also exists in copy_to_user_page and copy_from_user_page
which was causing the machine to die under rare circumstances for example
when running ps if the BUG_ON() assertion added by the earlier fix was
getting triggered.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPSsim probably doesn't have any sort of environment, but writing
a zero in it kills even the compiled in command line. This prevents
booting via NFS root.
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip22/ip22-berr.o
arch/mips/sgi-ip22/ip22-berr.c: In function 'ip22_be_interrupt':
arch/mips/sgi-ip22/ip22-berr.c💯 warning: passing argument 2 of 'die_if_kernel' discards qualifiers from pointer target type
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the warning:
CC arch/mips/sgi-ip22/ip22-reset.o
arch/mips/sgi-ip22/ip22-reset.c: In function 'reboot_setup':
arch/mips/sgi-ip22/ip22-reset.c:239: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rtc-ds1742 platform driver name doesn't match its module name,
which might prevents it from properly hotplugging. There is only two
in-tree user of its driver, which are fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.
Killing just one of the process threads can leave the application in a bad
state, whereas killing the entire process group would allow for the
application to restart, or be otherwise handled, and makes it very obvious
that something has gone wrong.
This change allows the entire process group to be taken down, rather
than just the one thread.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical handlers of PTRACE_DETACH go into ptrace_request().
Not touching compat code.
Not touching archs that don't call ptrace_request.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable AFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of AFLAGS with KBUILD_AFLAGS all over
the tree.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Update AU1000 get_ethernet_addr().
Three functions were brought together in one.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The variable CFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
On top of that several people over time has asked for a way to
pass in additional flags to gcc.
This patch replace use of CFLAGS with KBUILD_CFLAGS all over the
tree and enabling one to use:
make CFLAGS=...
to specify additional gcc commandline options.
One usecase is when trying to find gcc bugs but other
use cases has been requested too.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k
Test was simple to do a defconfig build, apply the patch and check
that nothing got rebuild.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Loading ELF binaries based on the section table is totally wrong. This
still leaves the other fat bug of referencing symbols in an executable
unfixed, so people better don't run strip on their binaries ...
As added bonus the new loader is also 23 lines shorter.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So far /proc/cpuinfo has been the only user but human readable processor
name are more useful than that for proc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dump the generated code for clear/copy page calls like it is done for TLB
fault handlers. Useful for debugging.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's only used in arch/mips/cobalt/reset.c.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They're only used in arch/mips/cobalt/console.c.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These PCI definitions are only used in arch/mips/pci/fixup-cobalt.c.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add Cobalt Qube series front LED support to platform register.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On MP configurations it's highly dubious what this code will actually
affect since blasting away cachelines may or may not do the right
thing wrt. cache coherency.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-msym32 and previously the strategy to tell the compiler to generate
64-bit code but the assembler to put it into 32-bit ELF was initially
a hack to get around the lack of proper 64-bit binutils support and
later turned into a neat optimization with significant code size
savings. But it's really just an optimization so there is nothing
wrong with just dropping the option (and whatever else goes along with
it, I forgot all the nasty details) on the floor if due to a vintage
compiler it can't be suported.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel currently only supports broadcasting of the timer interrupt
from a single timer, not multicasting into two multicast groups of
processors. So the implemented mechanism for SMTC works by broadcasting
the cp0 compare interrupt on VPE 0 and ignoring it on any additional VPEs.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This replaces the MIPS-specific to_tm function with the generic
rtc_time_to_tm function. The big difference between the two functions is
that rtc_time_to_tm uses epoch 70 while to_tm uses 1970, so the result of
rtc_time_to_tm needs to be fixed up.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hard to follow who is pointing what to where and why so it's simply getting
in the way of the time code renovation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This has not been any serious user of this ill conceived thing since the
original invention in like '95.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add LED support to the WGT634U machine. It uses the new gpio-led
driver and a platform driver for the pin definitions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add GPIO support to the BCM47XX platform. It will be used by a GPIO
LED driver.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add CFE support to the BCM47XX code. That includes querying CFE environment
variables as well as using CFE to print messages before the serial port is
initialized (early printk).
Signed-off-by: Aurelien Jarno <aurel32@farad.aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the platform independent part of the CFE code to arch/mips/fw/cfe from
arch/mips/sibyte/cfe.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
