Make needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It appears in /sys/mdX/md/dev-YYY/state
and can be set or cleared by writing 'writemostly' or '-writemostly'
respectively.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The md/dev-XXX/state file can now be written:
"faulty" simulates an error on the device
"remove" removes the device from the array (if it is not busy)
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.
Array states/settings:
clear
No devices, no size, no level
Equivalent to STOP_ARRAY ioctl
inactive
May have some settings, but array is not active
all IO results in error
When written, doesn't tear down array, but just stops it
suspended (not supported yet)
All IO requests will block. The array can be reconfigured.
Writing this, if accepted, will block until array is quiescent
readonly
no resync can happen. no superblocks get written.
write requests fail
read-auto
like readonly, but behaves like 'clean' on a write request.
clean - no pending writes, but otherwise active.
When written to inactive array, starts without resync
If a write request arrives then
if metadata is known, mark 'dirty' and switch to 'active'.
if not known, block and switch to write-pending
If written to an active array that has pending writes, then fails.
active
fully active: IO and resync can be happening.
When written to inactive array, starts with resync
write-pending (not supported yet)
clean, but writes are blocked waiting for 'active' to be written.
active-idle
like active, but no writes have been seen for a while (100msec).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- record the 'event' count on each individual device (they
might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
block only needs to be updated to record a clean<->dirty
transition.
- Prefer odd event numbers for dirty states and even numbers
for clean states
- Using all the above, don't update the superblock on
a spare device if the update is just doing a clean-dirty
transition. To accomodate this, a transition from
dirty back to clean might now decrement the events counter
if nothing else has changed.
The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.
It should be possible to do a similar thing to arrays without bitmaps. i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.
This patch allows that option. This means that when assembling an array one
device at a time (e.g. during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap modifies i_writecount of a bitmap file to make sure that no-one else
writes to it. The reverting of the change is sometimes done twice, and there
is one error path where it is omitted.
This patch tidies that up.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When "mdadm --grow /dev/mdX --bitmap=none" is used to remove a filebacked
bitmap, the bitmap was disconnected from the array, but the file wasn't closed
(until the array was stopped).
The file also wasn't closed if adding the bitmap file failed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the needlessly global md_print_devices() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At shutdown, we switch all arrays to read-only, which creates a message for
every instantiated array, even those which aren't actually active.
So remove the message for non-active arrays.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a md array has been idle (no writes) for 20msecs it is marked as 'clean'.
This delay turns out to be too short for some real workloads. So increase it
to 200msec (the time to update the metadata should be a tiny fraction of that)
and make it sysfs-configurable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This warning was slightly useful back in 2.2 days, but is more an annoyance
now. It makes it awkward to add new ioctls (that we we are likely to do that
in the current climate, but it is possible).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: NeilBrown <neilb@suse.de>
If an error is reported by a drive in a RAID array (which is done via
bi_end_io - in interrupt context), we call md_error and md_new_event which
calls sysfs_notify. However sysfs_notify grabs a mutex and so cannot be
called in interrupt context.
This patch just creates a variant of md_new_event which avoids the sysfs
call, and uses that. A better fix for later is to arrange for the event to
be called from user-context.
Note: avoiding the sysfs call isn't a problem as an error will not, by
itself, modify the sync_action attribute. (We do still need to
wake_up(&md_event_waiters) as an error by itself will modify /proc/mdstat).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
otherwise we get nasty messages about locks not being released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should be able to write 'repair' to /sys/block/mdX/md/sync_action,
however due to and inverted test, that always given EINVAL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix mddev_lock() usage bugs in md_attr_show() and md_attr_store().
[they did not anticipate the possibility of getting a signal]
- remove mddev_lock_uninterruptible() [unused]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It works like this:
Open the file
Read all the contents.
Call poll requesting POLLERR or POLLPRI (so select/exceptfds works)
When poll returns,
close the file and go to top of loop.
or lseek to start of file and go back to the 'read'.
Events are signaled by an object manager calling
sysfs_notify(kobj, dir, attr);
If the dir is non-NULL, it is used to find a subdirectory which
contains the attribute (presumably created by sysfs_create_group).
This has a cost of one int per attribute, one wait_queuehead per kobject,
one int per open file.
The name "sysfs_notify" may be confused with the inotify
functionality. Maybe it would be nice to support inotify for sysfs
attributes as well?
This patch also uses sysfs_notify to allow /sys/block/md*/md/sync_action
to be pollable
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And remove the comments that were put in inplace of a fix too....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... being careful that mutex_trylock is inverted wrt down_trylock
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An md array can be asked to change the amount of each device that it is using,
and in particular can be asked to use the maximum available space. This
currently only works if the first device is not larger than the rest. As
'size' gets changed and so 'fit' becomes wrong. So check if a 'fit' is
required early and don't corrupt it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows user-space to access data safely. This is needed for raid5
reshape as user-space needs to take a backup of the first few stripes before
allowing reshape to commence.
It will also be useful in cluster-aware raid1 configurations so that all
cluster members can leave a section of the array untouched while a
resync/recovery happens.
A 'start' and 'end' of the suspended range are written to 2 sysfs attributes.
Note that only one range can be suspended at a time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows reshape to be triggerred via sysfs (which is the only way to start
it happening).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_reshape checks validity and does things that can be done instantly -
like adding devices to raid1. start_reshape initiates a restriping process to
convert the whole array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We allow the superblock to record an 'old' and a 'new' geometry, and a
position where any conversion is up to. The geometry allows for changing
chunksize, layout and level as well as number of devices.
When using verion-0.90 superblock, we convert the version to 0.91 while the
conversion is happening so that an old kernel will refuse the assemble the
array. For version-1, we use a feature bit for the same effect.
When starting an array we check for an incomplete reshape and restart the
reshape process if needed. If the reshape stopped at an awkward time (like
when updating the first stripe) we refuse to assemble the array, and let
user-space worry about it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds raid5_reshape and end_reshape which will start and finish the
reshape processes.
raid5_reshape is only enabled in CONFIG_MD_RAID5_RESHAPE is set, to discourage
accidental use.
Read the 'help' for the CONFIG_MD_RAID5_RESHAPE entry.
and Make sure that you have backups, just in case.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the core of the resize/expand process.
sync_request notices if a 'reshape' is happening and acts accordingly.
It allocated new stripe_heads for the next chunk-wide-stripe in the target
geometry, marking them STRIPE_EXPANDING.
Then it finds which stripe heads in the old geometry can provide data needed
by these and marks them STRIPE_EXPAND_SOURCE. This causes stripe_handle to
read all blocks on those stripes.
Once all blocks on a STRIPE_EXPAND_SOURCE stripe_head are read, any that are
needed are copied into the corresponding STRIPE_EXPANDING stripe_head. Once a
STRIPE_EXPANDING stripe_head is full, it is marks STRIPE_EXPAND_READY and then
is written out and released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before a RAID-5 can be expanded, we need to be able to expand the stripe-cache
data structure.
This requires allocating new stripes in a new kmem_cache. If this succeeds,
we copy cache pages over and release the old stripes and kmem_cache.
We then allocate new pages. If that fails, we leave the stripe cache at it's
new size. It isn't worth the effort to shrink it back again.
Unfortuanately this means we need two kmem_cache names as we, for a short
period of time, we have two kmem_caches. So they are raid5/%s and
raid5/%s-alt
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
status_resync - used by /proc/mdstat to report the status of a resync, assumes
that device sizes will always fit into an 'unsigned long' This is no longer
the case...
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We are counting failed devices twice, once of the device that is failed, and
once for the hole that has been left in the array. Remove the former so
'failed' matches 'missing'. Storing these counts in the superblock is a bit
silly anyway....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I really should make this a function of the personality....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This flag should be set for a virtual device iff it is set for all underlying
devices.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use bd_claim_by_disk.
Following symlinks are created if md0 is built from sda and sdb
/sys/block/md0/slaves/sda --> /sys/block/sda
/sys/block/md0/slaves/sdb --> /sys/block/sdb
/sys/block/sda/holders/md0 --> /sys/block/md0
/sys/block/sdb/holders/md0 --> /sys/block/md0
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sometimes it doesn't so make the code more like the version-0 code which
works.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- version-1 superblock
+ The default_bitmap_offset is in sectors, not bytes.
+ the 'size' field in the superblock is in sectors, not KB
- raid0_run should return a negative number on error, not '1'
- raid10_read_balance should not return a valid 'disk' number if
->rdev turned out to be NULL
- kmem_cache_destroy doesn't like being passed a NULL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mdu_array_info_t->size is 'int', which isn't big enough for the size (in KB of
each component in) some arrays.
So rather than a random overflow, set size to -1 when it cannot be set
correctly.
To update aspect on an array, userspace will sometimes:
get_array_info
change one field
set_array_info
in this case, we don't want the '-1' in 'size' to change to size, or look like
a size change at all. So test for that in update_array_info.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While a read-only array doesn't not really need a bitmap, we should
not remove the bitmap when switching an array to read-only because
a/ There is no code to re-add the bitmap which switching to read-write,
b/ There is insufficient locking - the bitmap could be accessed while it is
being removed.
Cc: Reuben Farrelly <reuben-lkml@reub.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
super_1_sync only updates fields in the superblock that might have changed.
'raid_disks' and 'size' could have changed, but this information doesn't get
updated.... until this patch.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As 'array_size' is a 'sector_t', it may overflow inappropriately when shifted
10 bits. So We should cast it to a loff_t first.
There are two places with this problem, but the second (in update_raid_disks)
isn't needed so just remove it:
The only personality that handles ->reshape currently is raid1,
and it doesn't change the size of the array.
When added for raid5/6, reshape again won't change the size of the array,
at least not straight away.
This code might be need for reshaping 'linear' but linear->shape,
if implemented, should probably do the i_size_write itself.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
