When both the gspca_sonixb and the sn9c102 driver are enabled, make the
gspca_sonixb driver handle cams with usb-id of 0c45:6007. The sn9c102 driver
is being phased out and gspca driver has been successfully tested
with an 0c45:6007 camara.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our hstart value was wrong for tas5110d sensor using sonixb cams, this
patch fixes this. Many thanks to Paulus (laudaka) for donating me a camera
with such a sensor IC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ov764x remove setting of AEC limits, as the custom values cause AEC
oscilation in 320x240.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: remove non functioning contrast control for ov764x sensor
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Differentiate between ov7640 and ov7648 and handle the ov7648 320x240
on the ov519 bridge specially to fix r and b being swapped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Deegan <michael@ucc.gu.uwa.edu.au>, has reported issues with
using 640x480 mode on his ov518+ webcam. The fix for this breaks things
on my ov518+ cam (Trust 320 Sp@cecam), this patch thus adds differentiation
in the driver between the OV7620 sensor his cam has and the OV7620AE sensor
my cam has, and then only changes the init sequence for the ov518+ +
OV7620 combo which was not working for Michael.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Streaming of VGA stv0680 based cams (instead of CIF ones) failed, because
we were using the wrong control pipe for certain commands, this patch fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark led on eyetoy II as inverted, I have the feeling the led needs to
be inverted for all 519 based cams (iow we got the set led code wrong), but
lets just deal with this one cam at a time to avoid breaking currently
working cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stv0680 cameras currently only work when already plugged in when the system
boots (or when manually re-loading the driver after boot). This patch fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New gspca subdriver adding support for SN9C2028 dual-mode cameras.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you read the mail to Oliver Neukum on the linux-usb list, then you know
that I found a cure for the mysterious problem that the MR97310a CIF "type
1" cameras have been freezing up and refusing to stream if hooked up to a
machine with a UHCI controller.
Namely, the cure is that if the camera is an mr97310a CIF type 1 camera, you
have to send it 0xa0, 0x00. Somehow, this is a timing reset command, or
such. It un-blocks whatever was previously stopping the CIF type 1 cameras
from working on the UHCI-based machines.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Exit stv090x_algo() if the tuner did not lock. This might happen due to
missing signal or invalid/incomplete tuning parameters.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C gate must also be disabled, if a tuner command failed.
Otherwise the tuner mutex would be locked forever.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When mclk is not 0 then it will never be set to the correct value and
the Demodulator will not work.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This gives the STV090x and improved clock signal (rectangle instead of sine).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using clk_div member of stv6110x_config structure the tuner's clock
output divider can be configured. It is set in stv6110x_attach.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed when clock input is driven from tuner and an output
divider different from 1 is used.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before there was used a static register map that could lead to issues
when there are are multiple adapters with the STV6110(A).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function stv6110x_write_regs is used to write several registers at once.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This could be useful for p.e. Common Interface applications where data rate is limited.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this change it is possible to have the same I2C address for both tuners.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the STV0900 features two demodulation paths in one chip there is
some information used by both instances of the driver when used in
dual mode. This information is now shared in an internal structure
referenced by I2C adapter and address.
Do initialisation of the demodulator only once when used in dual mode.
Moved global mutex demod_lock to internal structure.
Moved dev_ver and mclk to internal structure.
Removed unused tuner_refclk from stv090x_state.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In automatic S/S2 detection mode, locking of a DVB-S transponder could
fail when coming from a DVB-S2 transponder. This change fixes the issue
by first disabling DVB-S and DVB-S2 mode before enabling it again.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
22-kHz tone can be driven in two ways:
1. LNBH24 can produce 22kHz continuous tone when TEN=1 ( 22 KHz tone output is
always activated ).
2. LNBH24 can reproduce 22kHz tone timings from DSQIN or EXTM pin's when TEN=0.
From LNBH24 datasheet:
"In order to improve design flexibility an external tone input pin is
available (EXTM). The EXTM is a Logic input pin which activates the 22 kHz
tone output, on the VoTX pin, by using the LNBH24 integrated tone generator
(similar to the DSQIN pin function). In fact, the output tone waveform
characteristics will always be internally controlled by the LNBH24 tone
generator and the EXTM signal will be used as a timing control for DiSEqC tone
data encoding on the VoTX output."
In NetUP Dual DVB-S2-CI card 22kHz tone timings on EXTM pin produced by
STV0900 demod:
.set_tone = stv0900_set_tone
redefine to "set_tone = lnbp21_set_tone" is not correct for "NetUP Dual
DVB-S2-CI card".
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The two sensors ov772x and ov965x have too much differences.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of
drivers/media/dvb/bt8xx/bt878.c
Please have a look at the small patch and either pull it through
your tree, or please ack' it so Jiri can pull it through the trivial
tree.
Patch against linux-next-tree, 22. Dez 08:38:18 CET 2009
but also present in linus tree.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And a little code refactoring/neatening around the removals
Reduces object size a little bit:
new:
$ size drivers/media/dvb/frontends/si21xx.o
text data bss dec hex filename
8984 56 1816 10856 2a68 drivers/media/dvb/frontends/si21xx.o
old:
$ size drivers/media/dvb/frontends/si21xx.o
text data bss dec hex filename
9084 56 1792 10932 2ab4 drivers/media/dvb/frontends/si21xx.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found a potential null dereference in cx18_dvb_start_feed
and cx18_dvb_stop_feed. There is a check for stream being NULL,
but it is dereferenced earlier. Move the dereference after the
check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Andy Walls <awalls@radix.net>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Free ir_dev before exit.
Found by cppcheck.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found an unreachable statement in zl10039_attach. There is
a `break' followed by `goto error'. Remove that break, so that it
can handle the error.
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found a memory leak in tuner_probe. It is not freed/assigned
on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stanse found a memory leak in smscore_gpio_configure. buffer is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The return of saa7164_i2caddr_to_reglen() was not tested.
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
this patch fixes a memory leak which occurs when an em28xx card with DVB
extension is unplugged or its DVB extension driver is unloaded. In
dvb_fini(), dev->dvb must be freed before being set to NULL, as is done
in dvb_init() in case of error.
Note that this bug is also present in the latest stable kernel release.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the declaration of the sysfs attributes for IR's, which
must be a NULL-terminated array of struct attribute *.
Without this patch, my machine crashes when inserting a DVB card.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I was initially concerned about the weird array index (the 2 bumps
into the next row of the array). Matthias Schwarzott look at the
datasheet and it turns out it should be zl10036_init_tab[1][0] |= 0x01;
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { <+... return NULL; ...+> }
@@
expression *x;
expression y;
identifier r.f;
statement S;
@@
x = f(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If there is ever going to be a FireDTV or FloppyDTV firmware which does
not provide a minimal ASCII textual descriptor for Model_Id --- or if
the descriptor is provided indirectly in a descriptor directory ---
the ieee1394 variant of the device probe of firedtv would dereference a
NULL pointer. The firewire variant of firedtv's device probe is not
affected.
The fix makes sure that such an unexpected firmware is safely recognized
by fdtv_alloc as an unknown firmware.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
