Move to using gpiolib to access the card detect and write protect GPIO
lines instead of using the platform speicifc s3c2410_gpio calls.
Also ensure that the card lines are claimed the same way to avoid overlap
with any other drivers.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the platform id list to match the three different versions of the
hardware block that this driver supports.
This will change the prefix of the console messages produced by this
driver to be prefixed by s3c-mci instead of the hardware block name, such
as s3c2440-mci.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the local definition RESSIZE() with the standard resource_size()
call for getting the size of a struct resource.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In charge/uncharge/reclaim path, usage_in_excess is calculated repeatedly
and it takes res_counter's spin_lock every time.
This patch removes unnecessary calls for res_count_soft_limit_excess.
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch clean up/fixes for memcg's uncharge soft limit path.
Problems:
Now, res_counter_charge()/uncharge() handles softlimit information at
charge/uncharge and softlimit-check is done when event counter per memcg
goes over limit. Now, event counter per memcg is updated only when
memory usage is over soft limit. Here, considering hierarchical memcg
management, ancesotors should be taken care of.
Now, ancerstors(hierarchy) are handled in charge() but not in uncharge().
This is not good.
Prolems:
1. memcg's event counter incremented only when softlimit hits. That's bad.
It makes event counter hard to be reused for other purpose.
2. At uncharge, only the lowest level rescounter is handled. This is bug.
Because ancesotor's event counter is not incremented, children should
take care of them.
3. res_counter_uncharge()'s 3rd argument is NULL in most case.
ops under res_counter->lock should be small. No "if" sentense is better.
Fixes:
* Removed soft_limit_xx poitner and checks in charge and uncharge.
Do-check-only-when-necessary scheme works enough well without them.
* make event-counter of memcg incremented at every charge/uncharge.
(per-cpu area will be accessed soon anyway)
* All ancestors are checked at soft-limit-check. This is necessary because
ancesotor's event counter may never be modified. Then, they should be
checked at the same time.
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__css_put() doesn't check a bug as refcnt goes to minus.
I think it should be caught. This patch adds a check for it.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__mem_cgroup_largest_soft_limit_node() returns a mem_cgroup_per_zone "mz"
with incremnted mz->mem->css's refcnt. Then, the caller of this function
has to call css_put(mz->mem->css).
But, mz can be !NULL even if "not found" i.e. without css_get(). By
this, css->refcnt will go down to minus.
This may cause various things...one of results will be
initite-loop in css_tryget() as this.
INFO: RCU detected CPU 0 stall (t=10000 jiffies)
sending NMI to all CPUs:
NMI backtrace for cpu 0
CPU 0:
<snip>
<<EOE>> <IRQ> [<ffffffff810884bd>] trace_hardirqs_off+0xd/0x10
[<ffffffff8102a940>] flat_send_IPI_mask+0x90/0xb0
[<ffffffff8102a9c9>] flat_send_IPI_all+0x69/0x70
[<ffffffff81027372>] arch_trigger_all_cpu_backtrace+0x62/0xa0
[<ffffffff810bff8e>] __rcu_pending+0x7e/0x370
[<ffffffff810c02c7>] rcu_check_callbacks+0x47/0x130
[<ffffffff81063a26>] update_process_times+0x46/0x70
[<ffffffff81085930>] tick_sched_timer+0x60/0x160
[<ffffffff810858d0>] ? tick_sched_timer+0x0/0x160
[<ffffffff8107a03a>] __run_hrtimer+0xba/0x150
[<ffffffff8107a325>] hrtimer_interrupt+0xd5/0x1b0
[<ffffffff81426dfe>] ? trace_hardirqs_off_thunk+0x3a/0x3c
[<ffffffff8142cacd>] smp_apic_timer_interrupt+0x6d/0x9b
[<ffffffff8100cb33>] apic_timer_interrupt+0x13/0x20
<EOI> [<ffffffff811317b6>] ? mem_cgroup_walk_tree+0x156/0x180
[<ffffffff811316d3>] ? mem_cgroup_walk_tree+0x73/0x180
[<ffffffff81131692>] ? mem_cgroup_walk_tree+0x32/0x180
[<ffffffff81131a00>] ? mem_cgroup_get_local_stat+0x0/0x110
[<ffffffff81131d5b>] ? mem_control_stat_show+0x14b/0x330
[<ffffffff810a57fd>] ? cgroup_seqfile_show+0x3d/0x60
Above shows CPU0 caught in css_tryget()'s inifinite loop because
of bad refcnt.
This is a fix to set mz=NULL at the top of retry path.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some configurations of the Timberdale FPGA has the uartlite
included.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch size comment is like so last millenium. Update it to modern
times.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some manufacturers provide vendor information in non-vendor specific CIS
tuples. For example, Broadcom uses an Extended Function tuple to provide
the MAC address on some of their network cards, as in the case of the
Nintendo Wii WLAN daughter card.
This patch allows passing whitelisted FUNCE tuples unknown to the SDIO
core to a matching SDIO driver instead of rejecting them and failing.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The page_address_in_vma() is not only used in unuse_vma().
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just like ip_fast_csum, the assembly snippet in csum_ipv6_magic needs a
memory clobber, as it is only passed the address of the buffer, not a
memory reference to the buffer itself.
This caused failures in Hurd's pfinetv4 when we tried to compile it with
gcc-4.3 (bogus checksums).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix some build failures when using gcc-4.x for MN10300.
Firstly, __get_user() fails to build because the pointer points to a const and
__gu_val ends up being read-only:
In file included from include/linux/mempolicy.h:62,
from init/main.c:50:
include/linux/pagemap.h: In function 'fault_in_pages_readable':
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
make[1]: *** [init/main.o] Error 1
Secondly, gcc-4 doesn't allow casts of lvalues:
UPD include/linux/compile.h
arch/mn10300/kernel/rtc.c: In function 'calibrate_clock':
arch/mn10300/kernel/rtc.c:170: error: lvalue required as left operand of assignment
arch/mn10300/kernel/rtc.c:172: error: lvalue required as left operand of assignment
make[1]: *** [arch/mn10300/kernel/rtc.o] Error 1
These are seen with gcc 4.2.1.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Tomas Cech <sleep_walker@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 45d80eea87 ("m68k: convert to
asm-generic/hardirq.h") - it fails to compile due to an inclusion tangle:
In file included from include/linux/irq.h:12,
from include/asm-generic/hardirq.h:6,
from /usr/src/devel/arch/m68k/include/asm/hardirq_mm.h:6,
from /usr/src/devel/arch/m68k/include/asm/hardirq.h:4,
from include/linux/hardirq.h:10,
from /usr/src/devel/arch/m68k/include/asm/system_mm.h:69,
from /usr/src/devel/arch/m68k/include/asm/system.h:4,
from include/linux/list.h:7,
from include/linux/preempt.h:11,
from include/linux/spinlock.h:50,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:56,
from arch/m68k/kernel/asm-offsets.c:14:
include/linux/smp.h:17: error: field 'list' has incomplete type
Cc: Christoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asm-generic/gpio.h header uses the might_sleep() macro but doesn't
include the header for it, so any source code that might include
linux/gpio.h before linux/kernel.h can easily lead to a build failure.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/input/input.c:1277: warning: 'input_dev_reset' defined but not used
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Starting from commit 4a4962263f "reduce
symbol table for loaded modules (v2)", the kernel/module.c build is broken
with CONFIG_KALLSYMS disabled.
CC kernel/module.o
kernel/module.c:1995: warning: type defaults to 'int' in declaration of 'Elf_Hdr'
kernel/module.c:1995: error: expected ';', ',' or ')' before '*' token
kernel/module.c: In function 'load_module':
kernel/module.c:2203: error: 'strmap' undeclared (first use in this function)
kernel/module.c:2203: error: (Each undeclared identifier is reported only once
kernel/module.c:2203: error: for each function it appears in.)
kernel/module.c:2239: error: 'symoffs' undeclared (first use in this function)
kernel/module.c:2239: error: implicit declaration of function 'layout_symtab'
kernel/module.c:2240: error: 'stroffs' undeclared (first use in this function)
make[1]: *** [kernel/module.o] Error 1
make: *** [kernel/module.o] Error 2
There are three different issues:
- layout_symtab() takes a const Elf_Ehdr
- layout_symtab() needs to return a value
- symoffs/stroffs/strmap are referenced by the load_module() code
despite being ifdefed out, which seems unnecessary given the noop
behaviour of layout_symtab()/add_kallsyms() in the case of
CONFIG_KALLSYMS=n.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch against v2.6.31 adds support for route lookup using sk_mark in some
more places. The benefits from this patch are the following.
First, SO_MARK option now has effect on UDP sockets too.
Second, ip_queue_xmit() and inet_sk_rebuild_header() could fail to do routing
lookup correctly if TCP sockets with SO_MARK were used.
Signed-off-by: Atis Elsts <atis@mikrotik.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
This is based on Michal Schmidt fix for skge.
Most network drivers request their IRQ when the interface is activated.
sky2 does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:
1. modprobe sky2
The card is detected as eth0 and requests IRQ 17. Directory
/proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
Now 8139too requests IRQ 17.
The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
The fix is for sky2 to name the irq based on the pci device, as is done
by some other devices DRM, infiniband, ... ie. sky2@pci:0000:00:00
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most network drivers request their IRQ when the interface is activated.
skge does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:
1. modprobe skge
The card is detected as eth0 and requests IRQ 17. Directory
/proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
Now 8139too requests IRQ 17.
The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
...
And "ls /proc/irq/17" shows two subdirectories, both called eth0.
Fix it by using a unique name for skge's IRQ, based on the PCI address.
The naming from the example then looks like this:
$ grep skge /proc/interrupts
17: 169 IO-APIC-fasteoi skge@pci:0000:00:0a.0, eth0
irqbalance daemon will have to be taught to recognize "skge@" as an
Ethernet interrupt. This will be a one-liner addition in classify.c. I
will send a patch to irqbalance if this change is accepted.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acknowledge TCP window scale support by inserting the proper option in SYN/ACK
and SYN headers even if our window scale is zero.
This fixes the following observed behavior:
1. Client sends a SYN with TCP window scaling option and non zero window scale
value to a Linux box.
2. Linux box notes large receive window from client.
3. Linux decides on a zero value of window scale for its part.
4. Due to compare against requested window scale size option, Linux does not to
send windows scale TCP option header on SYN/ACK at all.
With the following result:
Client box thinks TCP window scaling is not supported, since SYN/ACK had no
TCP window scale option, while Linux thinks that TCP window scaling is
supported (and scale might be non zero), since SYN had TCP window scale
option and we have a mismatched idea between the client and server
regarding window sizes.
Probably it also fixes up the following bug (not observed in practice):
1. Linux box opens TCP connection to some server.
2. Linux decides on zero value of window scale.
3. Due to compare against computed window scale size option, Linux does
not to set windows scale TCP option header on SYN.
With the expected result that the server OS does not use window scale option
due to not receiving such an option in the SYN headers, leading to suboptimal
performance.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Signed-off-by: Ori Finkelman <ori@comsleep.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/tcp.c: In function 'do_tcp_setsockopt':
net/ipv4/tcp.c:2050: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove references to dead web site mosquitonet.Stanford.EDU.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This typo was introduced by 5793f4be23 on
October 14, 2005 ...
Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
prev_vlan_tag field is not used.
Patch saves 512*8 bytes per tx queue ring on 64bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Matthew Carlson <mcarlson@broadcom.com>
The function virtnet_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sgiseeq_remove is defined using __exit, so don't use
__devexit_p but __exit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The function meth_remove is defined using __exit, so don't use __devexit_p
but __exit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Primary module parameter passed to bonding is pernament. That means if you
release the primary slave and enslave it again, it becomes the primary slave
again. But if you set primary slave via sysfs, the primary slave is only set
once and it's not remembered in bond->params structure. Therefore the setting is
lost after releasing the primary slave. This simple one-liner fixes this.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a problem where page_mkwrite can be called on a dirtied page that
already has a delalloc range associated with it. The fix is to clear any
delalloc bits for the range we are dirtying so the space accounting gets
handled properly. This is the same thing we do in the normal write case, so we
are consistent across the board. With this patch we no longer leak reserved
space.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Since 2.6.31 now has request-based device-mapper, it's useful to have
a tracepoint for request-remapping as well as bio-remapping.
This patch adds a tracepoint for request-remapping, trace_block_rq_remap().
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Currently we set the bio size to the byte equivalent of the blocks to
be trimmed when submitting the initial DISCARD ioctl. That means it
is subject to the max_hw_sectors limitation of the HBA which is
much lower than the size of a DISCARD request we can support.
Add a separate max_discard_sectors tunable to limit the size for discard
requests.
We limit the max discard request size in bytes to 32bit as that is the
limit for bio->bi_size. This could be much larger if we had a way to pass
that information through the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
prepare_discard_fn() was being called in a place where memory allocation
was effectively impossible. This makes it inappropriate for all but
the most trivial translations of Linux's DISCARD operation to the block
command set. Additionally adding a payload there makes the ownership
of the bio backing unclear as it's now allocated by the device driver
and not the submitter as usual.
It is replaced with QUEUE_FLAG_DISCARD which is used to indicate whether
the queue supports discard operations or not. blkdev_issue_discard now
allocates a one-page, sector-length payload which is the right thing
for the common ATA and SCSI implementations.
The mtd implementation of prepare_discard_fn() is replaced with simply
checking for the request being a discard.
Largely based on a previous patch from Matthew Wilcox <matthew@wil.cx>
which did the prepare_discard_fn but not the different payload allocation
yet.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
While testing Swap over NFS patchset, I noticed an oops that was triggered
during swapon. Investigating further, the NULL pointer deference is due to the
SSD device check/optimization in the swapon code that assumes s_bdev could never
be NULL.
inode->i_sb->s_bdev could be NULL in a few cases. For e.g. one such case is
loopback NFS mount, there could be others as well. Fix this by ensuring s_bdev
is not NULL before we try to deference s_bdev.
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As mentioned in Documentation/CodingStyle, move EXPORT* macro's
to the line immediately after the closing function brace line.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix these build errors when CONFIG_PROC_FS is not set:
drivers/block/cciss.c: In function 'cciss_show_raid_level':
drivers/block/cciss.c:623: error: 'RAID_UNKNOWN' undeclared (first use in this function)
drivers/block/cciss.c:626: error: 'raid_label' undeclared (first use in this function)
drivers/block/cciss.c: In function 'cciss_geometry_inquiry':
drivers/block/cciss.c:2696: error: 'RAID_UNKNOWN' undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Stacking devices do not have an inherent max_hw_sector limit. Set the
default to INT_MAX so we are bounded only by capabilities of the
underlying storage.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The topology changes unintentionally caused SAFE_MAX_SECTORS to be set
for stacking devices. Set the default limit to BLK_DEF_MAX_SECTORS and
provide SAFE_MAX_SECTORS in blk_queue_make_request() for legacy hw
drivers that depend on the old behavior.
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: Dynamically allocate the drive_info_struct for each logical drive.
This reduces the size of the per-hba ctlr_info structure from 106936
bytes to 8132 bytes. That's on 32-bit systems. On 64-bit systems, the
improvement is even bigger. Without this, the ctlr_info struct is so big
that the driver won't even load on a 64 bit system if CISS_MAX_LUN was
at it's current setting of 1024 logical drives.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add usage_count attribute to each logical drive at
/sys/devices/<dev>/ccissX/cXdY/usage_count for controller X,
logical drive Y. The usage count is the number of times
the device has currently been opened.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
and change get rid of some magic numbers in raid lavel decoding.
Add raid_level attribute to each logical drive at
/sys/devices/<dev>/ccissX/cXdY/raid_level for controller X,
logical drive Y
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: fix some magic numbers in the raid-level decoding
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add lunid attribute to each logical drive at
/sys/devices/<dev>/ccissX/cXdY/lunid for controller X,
logical drive Y
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>