Changed jobs and the Freescale address is no longer valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Fri, Nov 11, 2005 at 12:58:40PM -0800, David S. Miller wrote:
>
> This change:
>
> diff-tree 8ca2bdc7a9 (from feee207e44d3643d19e648aAuthor: Christoph Hellwig <hch@lst.de>
> Date: Wed Nov 9 12:07:18 2005 -0800
>
> [SPARC] sbus rtc: implement ->compat_ioctl
>
> Signed-off-by: Christoph Hellwig <hch@lst.de>
> Signed-off-by: David S. Miller <davem@davemloft.net>
>
> results in the console now getting spewed on sparc64 systems
> with messages like:
>
> [ 11.968298] ioctl32(hwclock:464): Unknown cmd fd(3) cmd(401c7014){00} arg(efc
> What's happening is hwclock tries first the SBUS rtc device ioctls
> then the normal rtc driver ones.
>
> So things actually worked better when we had the SBUS rtc compat ioctl
> directly handled via the generic compat ioctl code.
>
> There are _so_ many rtc drivers in the kernel implementing the
> generic rtc ioctls that I don't think putting a ->compat_ioctl
> into all of them to fix this problem is feasible. Unless we
> write a single rtc_compat_ioctl(), export it to modules, and hook
> it into all of those somehow.
>
> But even that doesn't appear to have any pretty implementation.
>
> Any better ideas?
We had similar problems with other ioctls where userspace did things
like that. What we did there was to put the compat handler to generic
code. The patch below does that, adding a big comment about what's
going on and removing the COMPAT_IOCTL entires for these on powerpc
that not only weren't ever useful but are duplicated now aswell.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We needed the VDSO symbols in the arch/ppc asm-offsets.c, and there
were a few usages of _systemcfg still left lying around.
Signed-off-by: Paul Mackerras <paulus@samba.org>
32-bit SMP powermacs weren't booting with ARCH=powerpc because the
boot cpu wasn't saving away the state of various control registers,
but the secondary CPUs were loading them from the uninitialized
state. This adds the necessary save-state call.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves the vdso's to arch/powerpc, adds support for the 32
bits vdso to the 32 bits kernel, rename systemcfg (finally !), and adds
some new (still untested) routines to both vdso's: clock_gettime() with
support for CLOCK_REALTIME and CLOCK_MONOTONIC, clock_getres() (same
clocks) and get_tbfreq() for glibc to retreive the timebase frequency.
Tom,Steve: The implementation of get_tbfreq() I've done for 32 bits
returns a long long (r3, r4) not a long. This is such that if we ever
add support for >4Ghz timebases on ppc32, the userland interface won't
have to change.
I have tested gettimeofday() using some glibc patches in both ppc32 and
ppc64 kernels using 32 bits userland (I haven't had a chance to test a
64 bits userland yet, but the implementation didn't change and was
tested earlier). I haven't tested yet the new functions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes a stray debugging printk which offended Anton.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the udbg code in ppc64 has no ppc32 equivalent, move it straight
over into arch/powerpc (and include/asm-powerpc for udbg.h). In time,
we probably want to meld the various bits and pieces of 32-bit early
debugging code into udbg, but for now only include it on
CONFIG_PPC64=y builds. The only change during the move is to
standardise the protecting #ifdef/#define in udbg.h, and move its
banner comment above the initial #ifdef (which seems to be normal
practice).
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built
for 32bit multiplatform (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we dont have permission to read some information from the hypervisor,
lparcfg outputs a warning on the console. Now that lparcfg is world
readable this is a problem.
Dont warn in the case of H_Authority, remove some unnecessary function
prototypes and fix whitespace damage in a structure as well.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also make klimit have the same type on 32-bit as on 64-bit,
namely unsigned long, and defines and initializes it in one place.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves a bunch more files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
hvcall.h
proc_ppc64.c
sysfs.c
lparcfg.c
rtas_pci.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is at the request of the glibc folks, who want to use these bits
to select libraries optimized for the microarchitecture and new
instructions in these processors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were getting the last_jiffy per-cpu variable set ahead of the current
timebase in smp_space_timers on SMP machines. This caused the loop in
timer_interrupt to loop virtually forever, since tb_ticks_since assumes
that it will never be called with the timebase behind the last_jiffy
value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates macros used to generate assembly for
compatibility across different CPUs or configs. A new header,
asm-powerpc/asm-compat.h contains the main compatibility macros. It
uses some preprocessor magic to make the macros suitable both for use
in .S files, and in inline asm in .c files. Headers (bitops.h,
uaccess.h, atomic.h, bug.h) which had their own such compatibility
macros are changed to use asm-compat.h.
ppc_asm.h is now for use in .S files *only*, and a #error enforces
that. As such, we're a lot more careless about namespace pollution
here than in asm-compat.h.
While we're at it, this patch adds a call to the PPC405_ERR77 macro in
futex.h which should have had it already, but didn't.
Built and booted on pSeries, Maple and iSeries (ARCH=powerpc). Built
for 32-bit powermac (ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc32 and ppc64 versions of cacheflush.h were almost identical.
The two versions of cache.h are fairly similar, except for a bunch of
register definitions in the ppc32 version which probably belong better
elsewhere. This patch, therefore, merges both headers. Notable
points:
- there are several functions in cacheflush.h which exist only
on ppc32 or only on ppc64. These are handled by #ifdef for now, but
these should probably be consolidated, along with the actual code
behind them later.
- Confusingly, both ppc32 and ppc64 have a
flush_dcache_range(), but they're subtly different: it uses dcbf on
ppc32 and dcbst on ppc64, ppc64 has a flush_inval_dcache_range() which
uses dcbf. These too should be merged and consolidated later.
- Also flush_dcache_range() was defined in cacheflush.h on
ppc64, and in cache.h on ppc32. In the merged version it's in
cacheflush.h
- On ppc32 flush_icache_range() is a normal function from
misc.S. On ppc64, it was wrapper, testing a feature bit before
calling __flush_icache_range() which does the actual flush. This
patch takes the ppc64 approach, which amounts to no change on ppc32,
since CPU_FTR_COHERENT_ICACHE will never be set there, but does mean
renaming flush_icache_range() to __flush_icache_range() in
arch/ppc/kernel/misc.S and arch/powerpc/kernel/misc_32.S
- The PReP register info from asm-ppc/cache.h has moved to
arch/ppc/platforms/prep_setup.c
- The 8xx register info from asm-ppc/cache.h has moved to a
new asm-powerpc/reg_8xx.h, included from reg.h
- flush_dcache_all() was defined on ppc32 (only), but was
never called (although it was exported). Thus this patch removes it
from cacheflush.h and from ARCH=powerpc (misc_32.S) entirely. It's
left in ARCH=ppc for now, with the prototype moved to ppc_ksyms.c.
Built for Walnut (ARCH=ppc), 32-bit multiplatform (pmac, CHRP and PReP
ARCH=ppc, pmac and CHRP ARCH=powerpc). Built and booted on POWER5
LPAR (ARCH=powerpc and ARCH=ppc64).
Built for 32-bit powermac (ARCH=ppc and ARCH=powerpc). Built and
booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built and booted
on G5 (ARCH=powerpc)
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to work around some problems with old versions of
Open Firmware, such as on the early powermacs (7500 etc.) and the
"Longtrail" CHRP machine. On these machines we have to claim
the physical and virtual address ranges explicitly when claiming
memory and then set up a V->P mapping.
The Longtrail has more problems: setprop doesn't work, and we have
to set an "allow-reclaim" variable to 0 in order to get claim on
physical memory ranges to fail if the memory is already claimed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves a bunch of files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
abs_addr.h
compat.h
lppaca.h
paca.h
tce.h
cpu_setup_power4.S
ioctl32.c
firmware.c
pacaData.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
- pacaData.c renamed paca.c to remove studlyCaps
- Misplaced { moved in lppaca.h
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having already merged the ppc and ppc64 versions of signal.c, this
patch finishes the job by merging signal.h. The two versions were
almost identical already. Notable changes:
- We use BITS_PER_LONG to correctly size sigset_t
- Remove some uneeded #includes and struct forward
declarations. This does mean adding an include to signal_32.c which
relied on the indirect inclusion of sigcontext.h
- As the ppc64 version, the merged signal.h has prototypes for
do_signal() and do_signal32(). Thus remove extra prototypes from
ppc_ksyms.c which had them directly.
Built and booted on POWER5 LPAR (ARCH=ppc64 and ARCH=powerpc). Built
for 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- Re-add a hunk lost during merge: ppc64 is missing the hunk that disables
preempt on the secondary CPUs before they call cpu_idle().
- ppc's cpu_idle() had the need_resched() test wrong.
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes e500 build and cleans up traps.c by moving perf_irq extern to
pmc.h.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A non-broken udev would autoload also the drivers for devices on the
pseries vio bus, like ibmveth, ibmvscsic and hvsc. This is similar to pci,
usb and ieee1394:
/lib/modules/`uname -r`/modules.alias
alias vio:TvscsiSIBM,v-scsi* ibmvscsic
alias vio:TnetworkSIBM,l-lan* ibmveth
alias vio:Tserial-serverShvterm2* hvcs
/events/debug.00004.pci.add.1394:MODALIAS='pci:v00001014d00000188sv00000000sd00000000bc06sc04i0f'
/events/debug.00005.pci.add.1509:MODALIAS='pci:v00008086d00001229sv00001014sd000001FFbc02sc00i00'
/events/debug.00026.vio.add.1519:MODALIAS='vio:TserialShvterm1'
/events/debug.00027.vio.add.1446:MODALIAS='vio:TvscsiSIBM,v-scsi'
/events/debug.00028.vio.add.1451:MODALIAS='vio:TnetworkSIBM,l-lan'
modprobe -v vio:TnetworkSIBM,l-lan
insmod /lib/modules/2.6.14-20051030_vio-ppc64/kernel/drivers/net/ibmveth.ko
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __do_IRQ instead. The only difference is that every controller
is now assumed to have an end() routine (only xics_8259 did not).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This factors out the common bits of arch/powerpc/xmon/start_*.c into
a new nonstdio.c, and removes some stuff that was supposed to make
xmon's I/O routines somewhat stdio-like but was never used.
It also makes the parsing of the xmon= command line option common,
so that ppc32 can now use xmon={off,on,early} also.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some powermac machines were crashing in the quiesce firmware call
in prom_init.c because we have just closed the OF stdin device;
notably my 1999 G3 powerbook does this. To avoid this, don't
close the OF stdin device on powermacs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Even though we can enable and disable xmon at runtime now, there are a
few places in the merge tree that call xmon and xmon_printf directly.
In the case below we call die() which will call xmon if it is enabled.
Also remove an unnecessary include of xmon.h in smp.c.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Building a PowerMac kernel with ARCH=powerpc causes a bunch of warnings,
this fixes some of them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some more U3 revisions have the missing "interrupts" property in U3,
this adds them to the fixup code in prom_init.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the ability to the SMU driver to recover missing
calibration partitions from the SMU chip itself. It also adds some
dynamic mecanism to /proc/device-tree so that new properties are visible
to userland.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
CPU freq support using 970FX powertune facility for iMac G5 and SMU
based single CPU desktop.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
OK, the Fedora ppc32 and ppc64 kernels should both be arch/powerpc by
tomorrow. They're booting on G5, POWER5, and my powerbook. I'll test
pmac SMP and Pegasos later -- but pmac smp is known broken in arch/ppc
anyway, and I'll live with a potential Pegasos regression for now; it
wasn't supported officially in FC4 either.
I needed to fix ppc32 initrd -- we were never setting initrd_start.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sys_ptrace boilerplate code (everything outside the big switch
statement for the arch-specific requests) is shared by most architectures.
This patch moves it to kernel/ptrace.c and leaves the arch-specific code as
arch_ptrace.
Some architectures have a too different ptrace so we have to exclude them.
They continue to keep their implementations. For sh64 I had to add a
sh64_ptrace wrapper because it does some initialization on the first call.
For um I removed an ifdefed SUBARCH_PTRACE_SPECIAL block, but
SUBARCH_PTRACE_SPECIAL isn't defined anywhere in the tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-By: David Howells <dhowells@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the AMCC PowerPC 440SPe SoC, including PCI Express in root
port mode.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two CONFIG_SMP=n build fixes due to missing <asm/smp.h> includes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define ppc_md.set_dabr for both 32 + 64 bit. Cleanup the implementation for
pSeries also, it was needlessly complex. Now we just do two firmware tests at
setup time, and use one of two functions, rather than using one function and
testing on every call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mostly this involves adding #include <asm/smp.h>, since that defines
things like boot_cpuid[_phys] and [gs]et_hard_smp_processor_id, which
are SMP-related but still needed on UP. This incorporates fixes
posted by Olof Johansson and Heikki Lindholm.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ancient ppcdebug/PPCDBG mechanism is now only used in two places.
First, in the hash setup code, one of the bits allows the size of the
hash table to be reduced by a factor of 8 - which would be better
accomplished with a command line option for that purpose. The other
was a bunch of bus walking related messages in the iSeries code, which
would seem to be insufficient reason to keep the mechanism.
This patch removes the last traces of this mechanism.
Built and booted on iSeries and pSeries POWER5 LPAR (ARCH=powerpc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K. The resulting kernel still boots on any
hardware. On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.
Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't currently use asm-ppc/page.h in vmlinux.lds.S, so until
we have a merged page.h, define PAGE_SIZE and KERNELBASE locally.
Also gets rid of some dynamic executable cruft that we had for
32-bit. With -Ttext=$(KERNELBASE) this didn't cause any problem,
but when we changed to putting . = KERNELBASE in the vmlinux.lds.S
this cruft caused the text to get linked at 0xa0 instead of
0xc0000000. Oops.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's no reason for smp_release_cpus() to be asm, and most people can make
more sense of C code. Add an extern declaration to smp.h and remove the custom
one in machine_kexec.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Currently we set the kernel entry point and the address of the text
section in the Makefile, using CONFIG_KERNEL_START.
But we've already got <asm/page.h> in the linker script, so we can just
use KERNELBASE directly. That means if we ever change KERNELBASE there's
one less place to change it.
And we can set the entry point with ENTRY().
There are zero differences from "readelf -a vmlinux" with or without this
patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
There's some debugging in prom.c that wraps nastly on 80 character
terminals, reformat it to fit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Move pSeries specific code in set_dabr() into a ppc_md function, this will
allow us to keep plpar_wrappers.h private to platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
This moves rtas-proc.c and rtas_flash.c into arch/powerpc/kernel, since
cell wants them as well as pseries (and chrp can use rtas-proc.c too,
at least in principle). rtas_fw.c is gone, with its bits moved into
rtas_flash.c and rtas.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This section of code calls .audit_syscal_exit, but is inside CONFIG_AUDIT,
so it will fail to build if CONFIG_AUDITSYSCALL is not defined.
After discussion with David Woodhouse, change the ifdef to
CONFIG_AUDITSYSCALL
Signed-off-by: Horms <horms@verge.net.au>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This simplifies the macros which are different between 32-bit and
64-bit. It also fixes a couple of printks on the bug->line element,
which is now a long.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A couple of instances of "i" that needed to be changed to "cpu_id"
got missed in the merge, because they were in CONFIG_TAU code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's a revised version. This re-introduces the set_bits() function
from ppc64, which I removed because I thought it was unused (it exists
on no other arch). In fact it is used in the powermac interrupt code
(but not on pSeries).
- We use LARXL/STCXL macros to generate the right (32 or 64 bit)
instructions, similar to LDL/STL from ppc_asm.h, used in fpu.S
- ppc32 previously used a full "sync" barrier at the end of
test_and_*_bit(), whereas ppc64 used an "isync". The merged version
uses "isync", since I believe that's sufficient.
- The ppc64 versions of then minix_*() bitmap functions have changed
semantics. Previously on ppc64, these functions were big-endian
(that is bit 0 was the LSB in the first 64-bit, big-endian word).
On ppc32 (and x86, for that matter, they were little-endian. As far
as I can tell, the big-endian usage was simply wrong - I guess
no-one ever tried to use minixfs on ppc64.
- On ppc32 find_next_bit() and find_next_zero_bit() are no longer
inline (they were already out-of-line on ppc64).
- For ppc64, sched_find_first_bit() has moved from mmu_context.h to
the merged bitops. What it was doing in mmu_context.h in the first
place, I have no idea.
- The fls() function is now implemented using the cntlzw instruction
on ppc64, instead of generic_fls(), as it already was on ppc32.
- For ARCH=ppc, this patch requires adding arch/powerpc/lib to the
arch/ppc/Makefile. This in turn requires some changes to
arch/powerpc/lib/Makefile which didn't correctly handle ARCH=ppc.
Built and running on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cell uses the same code as pSeries for flashing the firmware
through rtas, so the implementation should not be part of
platforms/pseries.
Put it into arch/powerpc/kernel instead.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The official name for BPA is now CBEA (Cell Broadband
Engine Architecture). This patch renames all occurences
of the term BPA to 'Cell' for easier recognition.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
By parsing the command line earlier, we can add the mem= value to the
flattened device tree and let the generic code sort out the memory limit
for us.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
We had a static memory_limit in prom.c, and then another one defined
in setup_64.c and used in numa.c, which resulted in the kernel crashing
when mem=xxx was given on the command line. This puts the declaration
in system.h and the definition in mem.c. This also moves the
definition of tce_alloc_start/end out of setup_64.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug where settimeofday would set the wrong parameters
in do_gtod, resulting in gettimeofday returning a value about 4
hours after the correct time. The bug was that we divided a
negative 64-bit value with do_div, which treated it as unsigned
and gave us a result that was approximately 1.8e10 too large
(since the divisor was 1e9).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somehow we ended up with an #ifdef CONFIG_PPC64 around the export
of cur_cpu_spec, but raid6 as a module needs it on ppc32 as well
as ppc64.
Signed-off-by: Paul Mackerras <paulus@samba.org>
remove duplicate local variable, saves 2 asm instructions.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The merged version follows the ppc64 version pretty closely mostly,
and in fact ARCH=ppc64 now uses the arch/powerpc/xmon version.
The main difference for ppc64 is that the 'p' command to call
show_state (which was always pretty dodgy) has been replaced by
the ppc32 'p' command, which calls a given procedure (so in fact
the old 'p' command behaviour can be achieved with 'p $show_state').
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows us to also use entry_64.S from the merged tree and reverts
the setup_64.c part of fda262b897.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Since I sent the patch to purge bootinfo.h from ARCH=powerpc and
ARCH=ppc64, setup-common.c has come into existence, and another
#include of bootinfo.h slipped in. This patch removes it. It also
removes include/asm-ppc64/bootinfo.h, which somehow survived the
previous patch which was supposed to remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
For the current time idle_6xx only applies to 6xx ppc32 CPUs
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 32-bit platforms, these convert from kernel virtual addresses
to real (physical addresses), like tophys/tovirt but they use
the same register for the source and destination. On 64-bit
platforms, they do nothing because the hardware ignores the top
two bits of the address in real mode.
These new macros are used in fpu.S now.
Signed-off-by: Paul Mackerras <paulus@samba.org>
With ARCH=powerpc we assume the presence of a device tree, so we don't
require any support for the old bi_recs method of passing boot
parameters. Likewise, we've never needed it for ppc64, but we still
had an include/asm-ppc64/bootinfo.h from which nothing was used. This
patch removes that file, and all references to it in arch/ppc64 and
arch/powerpc. A related, unused variable 'boot_mem_size' is also
removed from setup_32.c. The bootinfo stuff remains in ARCH=ppc for
the time being.
Built and booted on Power5 (ARCH=ppc64 and ARCH=powerpc), built for
32-bit powermac (ARCH=powerpc and ARCH=ppc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent merge of fpu.S broken the handling of fpscr for
ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted,
leading to strange random application crashes.
The confusion arises, because the thread_struct has (and requires) a
64-bit area to save the fpscr, because we use load/store double
instructions to get it in to/out of the FPU. However, only the low
32-bits are actually used, so we want to treat it as a 32-bit quantity
when manipulating its bits to avoid extra load/stores on 32-bit. This
patch replaces the current definition with a structure of two 32-bit
quantities (pad and val), to clarify things as much as is possible.
The 'val' field is used when manipulating bits, the structure itself
is used when obtaining the address for loading/unloading the value
from the FPU.
While we're at it, consolidate the 4 (!) almost identical versions of
cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S,
arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S,
arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The
new version takes a pointer to thread_struct and applies the correct
offset itself, rather than a pointer to the fpscr field itself, again
to avoid confusion as to which is the correct field to use.
Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S
code, which it previously did not.
Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc
and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y).
Booted on G5 (ARCH=powerpc) and things which previously fell over no
longer do.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and use setup_64.c from the merged tree instead. The only difference
between them was the code to set up the syscall maps.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Talk about buggy firmware... the OF on the Longtrail returns 0
from the claim client service rather than -1 when the claim fails.
It also has no device_type on the /memory node and blows up if
the output buffer for package-to-path is too big.
This also fixes a bug with calling alloc_up with align == 0, where
we did _ALIGN_UP(alloc_bottom, 0) which will end up as 0.
Lastly, we now check the return value (in r3) from calling the
prom, and return -1 from call_prom if we get a negative value back.
That is supposed to indicate that the requested client service
doesn't exist.
Signed-off-by: Paul Mackerras <paulus@samba.org>
SMP still needs more work but UP gets as far as starting userspace
at least. This uses the 64-bit-style code for spinning up the cpus.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The interrupt-tree parsing code wasn't offsetting interrupt numbers
by 16 on 32-bit platforms with an i8259 interrupt controller, and
it was confused about the encoding of interrupt sense and level
(which is different for i8259 and openpic interrupt controllers,
just to make things interesting).
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates a new arch/powerpc/kernel/setup-common.c with various
bits that setup_32.c and setup_64.c had in common - functions like
machine_shutdown/restart/power_off, show_cpuinfo, set_preferred_console
etc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits arch/ppc64/kernel/rtas.c into arch/powerpc/kernel/rtas.c,
which contains generic RTAS functions useful on any CHRP platform,
and arch/powerpc/platforms/pseries/rtas-fw.[ch], which contain
some pSeries-specific firmware flashing bits. The parts of rtas.c
that are to do with pSeries-specific error logging are protected
by a new CONFIG_RTAS_ERROR_LOGGING symbol. The inclusion of rtas.o
is controlled by the CONFIG_PPC_RTAS symbol, and the relevant
platforms select that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Removed of_show_percpuinfo and just report CPU frequency in generic
show_cpuinfo code.
* Killed OCP and PPC_SYS related code which doesn't belong in the
merge tree
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to initialize some control SPRS for timers on Book-E before
we start taking decrementer interrupts.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On !CONFIG_PPC_MULTIPLATFORM _machine is defined as 0. This is ok, but
we can't assign a value to _machine then.
We may not have CONFIG_PCI available, so only build in support for
find_parent_pci_resource(), request_OF_resource(), release_OF_resource()
if PCI is enabled. This is probably not the long term fix but works out
for now.
Make reg_property64 contain 64-bit elements on a 32-bit machine.
Mark the deprecated prom.c functions as __deprecated.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Its valid for ppc_md.set_rtc_time to be NULL. We need to check
that its non-NULL before trying to update the RTC.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a shutdown member to struct vio_driver. We also need vio_bus_shutdown()
which converts from struct device to struct vio_dev and knows how to extract
the struct vio_driver.
Original patch adjusted for different location of vio.c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Just set the name field directly in the device_driver structure
contained in the vio_driver struct.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Merge arch/ppc64/kernel/vio.c into arch/powerpc/kernel/vio.c, update
the Makefiles to make it work, and make ARCH=ppc64 still work.
Michael's version put vio.c in arch/powerpc/sysedv but after consolting
Paulus, this one puts it in arch/powerpc/kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Old powermacs have a number of differences from current machines:
- there is no interrupt tree in the device tree, just interrupt
or AAPL,interrupt properties
- the chosen node in the device tree is called /chosen@0
- the OF claim method doesn't map the memory, so we have to do
an explicit map call as well
- there is no /chosen/cpu property on SMP machines
- the NVRAM isn't structured as a set of partitions.
This adapts the merged powermac support code to cope with these
issues.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 601 doesn't have the timebase register; instead it has an RTCL
register that counts nanoseconds and wraps at 1000000000, and an
RTCU register that counts seconds. This makes the necessary changes
for the merged time code to use the RTCL/U registers when the kernel
is running on a 601.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This brings in a lot of changes from arch/ppc64/kernel/pmac_*.c to
arch/powerpc/platforms/powermac/*.c and makes various minor tweaks
elsewhere. On the powermac we now initialize ppc_md by copying
the whole pmac_md structure into it, which required some changes in
the ordering of initializations of individual fields of it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves smp_space_timers from arch/ppc64/kernel/smp.c to
arch/powerpc/kernel/time.c and makes it initialize last_jiffy[]
instead of paca[].next_jiffy_update_tb, since last_jiffy[] is
now what the time code uses. It also declares smp_space_timers
in include/asm-powerpc/time.h and gets rid of an ifdef in
div128_by_32.
Signed-off-by: Paul Mackerras <paulus@samba.org>
An error in merging led to 32-bit processes getting the wrong link
register value on entry to RT signal handlers, and the wrong stack
chain as well. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The merge of syscalls.c & sys_ppc32.c (30286ef6e0)
broke mmap, if the mmap returned a 64 bit address.
do_mmap2 was taking the return value from do_mmap_pgoff (an unsigned long), and
storing it in an int, before returning it to sys_mmap as an unsigned long. So
we were losing the high bits of the address.
You would have thought the compiler could catch this for us ...
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch to make process.c work for 32-bit and 64-bit
(06d67d5474) broke some 64-bit binaries.
We were blowing away load_addr in gpr[2], so we weren't properly relocating
the entry point.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge ppc32 and ppc64 versions of thread_info.h. They were pretty
similar already, the chief changes are:
- Instead of inline asm to implement current_thread_info(),
which needs to be different for ppc32 and ppc64, we use C with an
asm("r1") register variable. gcc turns it into the same asm as we
used to have for both platforms.
- We replace ppc32's 'local_flags' with the ppc64
'syscall_noerror' field. The noerror flag was in fact the only thing
in the local_flags field anyway, so the ppc64 approach is simpler, and
means we only need a load-immediate/store instead of load/mask/store
when clearing the flag.
- In readiness for 64k pages, when THREAD_SIZE will be less
than a page, ppc64 used kmalloc() rather than get_free_pages() to
allocate the kernel stack. With this patch we do the same for ppc32,
since there's no strong reason not to.
- For ppc64, we no longer export THREAD_SHIFT and THREAD_SIZE
via asm-offsets, thread_info.h can now be safely included in asm, as
on ppc32.
Built and booted on G4 Powerbook (ARCH=ppc and ARCH=powerpc) and
Power5 (ARCH=ppc64 and ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I had the sense of the test for when to use the old 601-style RTC
registers inverted. pmac_calibrate_decr and via_calibrate_decr
weren't setting ppc_tb_freq, on which all the further calculations
depended. Lastly, update_gtod was losing the top 32 bits of
the new tb_to_xs value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously the individual xxx_calibrate_decr functions would each
print the timebase and cpu frequency and calculate several values
such as tb_to_us and tb_to_xs. This moves those printks and
calculations into time_init just after the call to the platform's
calibrate_decr function.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This way they get done in one place for all platforms, and it is
more consistent with what ppc32 does.
Signed-off-by: Paul Mackerras <paulus@samba.org>
I missed a few places where ppc code was still assuming that the
ppc_md.show_[per]cpuinfo functions returned int.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patches the ppc32 and ppc64 versions of the headers and .c files
with helper functions for manipulating the performance counting
hardware. As a side effect, it removes use of the term "perfmon" from
ppc32, thus avoiding confusion with the unrelated performance counter
interface from HP Labs also called "perfmon".
Built, but not booted, for g5, pSeries, iSeries, and 32-bit Powermac
with both ARCH=powerpc and ARCH=ppc{,64} as appropriate.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We now use the merged time.c for both 32-bit and 64-bit compilation
with ARCH=powerpc, and for ARCH=ppc64, but not for ARCH=ppc32.
This removes setup_default_decr (folds its function into time_init)
and moves wakeup_decrementer into time.c. This also makes an
asm-powerpc/rtc.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows us to get rid of one type of entry in systbl.S.
In passing we remove the duplicate compat_sys_getdents and
compat_sys_utimes for which there are generic versions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This makes ppc use the syscalls.c from arch/powerpc/kernel, exports
copy_and_flush from head_32.S for use by prom_init.c (ARCH=powerpc),
and consolidates the sys_fadvise64_64 implementations for 32-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
With ARCH=powerpc, a spurious ifdef in prom_init prevented the
seconday hold loop being correctly copied down on Maple. With this
patch, Maple boots with ARCH=powerpc
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The merge-tree version of LOADBASE actually loads the whole given
address from the toc for ppc64. The matching OFF macro adjust for
this, using an offset of 0 for ppc64, but we weren't using that in
power4_idle.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The _GLOBAL() macro is for text symbols only. Changed to using
.globl for .data symbols.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were initializing the btext stuff from prom_init(), thus breaking
the rule that all communication between prom_init() and the rest of
the kernel has to be via the flattened device tree. This removes
the btext initialization calls from prom_init() and initializes it
instead after the device tree is unflattened. It would be nice to
do it earlier, but that needs some more infrastructure to find the
properties we need in the flattened device tree.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We weren't computing the size of the hash table correctly on iSeries
because the relevant code in prom.c was #ifdef CONFIG_PPC_PSERIES.
This moves the code to hash_utils_64.c, makes it unconditional, and
cleans it up a bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes up a variety of minor problems in compiling with ARCH=ppc
arising from using the merged versions of various header files.
A lot of the changes are just adding #include <asm/machdep.h> to
files that use ppc_md or smp_ops_t.
This also arranges for us to use semaphore.c, vecemu.c, vector.S and
fpu.S from arch/powerpc/kernel when compiling with ARCH=ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bunch of printks were left in arch/powerpc/kernel/setup_64.c from
when I was chasing a bug. This removes them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This was preventing us from recognizing that we did actually
instantiate RTAS successfully on pSeries.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a bunch of mostly small fixes that are needed to get
ARCH=powerpc to compile for 64-bit. This adds setup_64.c from
arch/ppc64/kernel/setup.c and locks.c from arch/ppc64/lib/locks.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since lparmap.s gets included in arch/powerpc/kernel/head_64.S,
this avoids depending on a file in another directory.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Although both ppc32 and ppc64 have a reloc_offset function, the ppc64
one produced the opposite sign to the ppc32 one. This standardizes
on the ppc32 sign and fixes the merged 64-bit code to account for that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The system call table has been consolidated into systbl.S. We have
separate 32-bit and 64-bit versions of entry.S and misc.S since the
code is mostly sufficiently different to be not worth merging.
There are some common bits that will be extracted in future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that the register names and bit definitions are all in reg.h,
use that instead of processor.h in assembly code in a few places.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This doesn't change any code, just renames things so we consistently
have foo_32.c and foo_64.c where we have separate 32- and 64-bit
versions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes symbols like HID0, SPRG3, SRR0, SRR1 etc. that refer to
special purpose registers to SPRN_HID0, SPRN_SPRG3, etc. Using the
SPRN_ symbols clutters the namespace less, and the forthcoming merge
of asm/processor.h and asm/reg.h is going to remove the non-SPRN_
versions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
These days there is no good reason to run a ppc32 kernel on a 64-bit
cpu, rather than a ppc64 kernel, so remove the config option and a
bunch of code (and ifdefs) from head.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This brings in the ppc64 version of prom_init.c, prom.c and btext.c
and makes them work for ppc32. This also brings in the new calling
convention, where the first entry to the kernel (with r5 != 0) goes
to the prom_init code, which then restarts from the beginning (with
r5 == 0) after it has done its stuff.
For now this also brings in the ppc32 version of setup.c. It also
merges lmb.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
These macros help in writing assembly code that works for both ppc32
and ppc64. With this we now have a common fpu.S. This takes out
load_up_fpu from head_64.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use idle_power4.S from ppc64 as we are not going to support
32 bit power4 in the merged tree.
Merge ppc64 traps.c into powerpc traps.c:
use ppc64 versions of exception routine names
(as they don't have StudlyCaps)
make all the versions if die() have the same
prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This updates the powermac SMP code to use the mpic driver instead of
the openpic driver and fixes the SMP-dependent context switch code.
We had a subtle bug where we were using interrupt numbers 256-259 for
IPIs, but ppc32 had NR_IRQS = 256. Moved the IPIs down to use interrupt
numbers 252-255 instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges ppc_ksyms.c, puts back the actual do_execve call in
sys_execve, makes init_MMU call find_end_of_memory rather than
ppc_md.find_end_of_memory (every platform has a device tree
with a /memory node now, right?) and fixes some problems with the
mpic initialization on newworld powermacs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changed ppc32 so that cur_cpu_spec is just a single pointer for all CPUs.
Additionally, made call_setup_cpu check to see if the cpu_setup pointer
is NULL or not before calling the function. This lets remove the dummy
cpu_setup calls that just return.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This file is the same in both architectures so create arch/powerpc/kernel
and move it there.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
