The usb max packet size won't change during the
device's presence. We should store it in a
variable inside rt2x00dev and use that.
This should also fix a division error when the
device is being hot-unplugged while a frame is
being send out.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler returns IRQ_NONE if it detects that the device
is gone. That's incorrect because the device may have raised the interrupt.
Not acknowledging it may trigger the spurious interrupt detection and kill
drivers sharing the interrupt line.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The validation of the chipset revision was broken
since for rt2500usb and rt73usb different registers
should be read. When rt2500usb was loaded for a rt73
device it would false think the chipset was correct
because the wrong register was read and validated.
This has been fixed by expanding the check to also
see if the first 4 bits of the revision is not-0
(When reading the wrong register offset the returned
value is usually 0 which can be interpreted as invalid)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes association failure (reason = 18) bug by arranging CCK
rates before OFDM rates. This patch will register with mac80211 the
modified rate arrangement with CCK rate first. Change rate scale algorithm
also to deal with rate change. Fix Txpower and rate Table commands to be
constructed correctly after rearrangement.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It makes no sense to enable interrupts if a device has been unplugged.
In addition if in doubt IRQ_HANDLED should be returned.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, iwlwifi would always use the first
registered rate control algorithm which, depending on system
setup, could be anything. After the mac80211 patch to make
the simple algorithm built-in, it would always be simple.
This has always been a bug in iwlwifi.
This fixes it by requesting that mac80211 selects the right
rate control algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCMCIA needs an additional step to request the IRQ.
No need to add code to release the IRQ here, as that's done
automatically in pcmcia_disable_device().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43legacy. If we call
b43legacy_wireless_core_stop(), it will set the status of the device to
INITIALIZED and the IRQ handler won't care any longer about IRQs, thus the
kernel will disable the IRQ if it's shared (unless we boot it with the
'irqpoll' option). So we must disable IRQs before changing the device
status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43. If we call b43_stop_wireless_core(), it
will set the status of the device to INITIALIZED and the IRQ handler won't
care any longer about IRQs, thus the kernel will disable the IRQ if it's
shared (unless we boot it with the 'irqpoll' option). So we must disable
IRQs before changing the device status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible buffer overrun.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */
This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up
Fix this by always re-allocating the rfkill stuff before register.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl->mutex might already be locked on initialization.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If i reaches zero, the loop ends, but the postfix decrement subtracts it to -1.
Testing for 'i == 0', later in the function, will not fulfill its purpose.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix section mismatch warning:
WARNING: vmlinux.o(.data+0x36fcc): Section mismatch: reference to .init.data:prism2_pci_id_table (between 'prism2_pci_drv_id' and 'prism2_pci_funcs')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 is broken when it comes down to adhoc and master mode.
The main problem is the beaconing, which is completely failing.
Untill a solution has been found, both beacon requiring modes
must be disabled to prevent numerous bug reports.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Properly account for queue commands, this fixes a problem reported
by Holger Schurig when using the debugfs interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incoming packets have to be aligned or the IP stack becomes upset.
Make sure to shift them two bytes to achieve this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes for slow hardware.
Signed-off-by: Vitaly V. Bursov <vitalyvb@ukr.net>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Intel device supported by the hermes driver core is the IPW2011. The
"Intel PRO/Wireless" wording suggests the later Centrino devices and may
be confusing to some users.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We conciously make a change here - we permit mode and speed setting to
be done in things like SLIP mode. There isn't actually a technical
reason to disallow this. It's usually a silly thing to do but we can
do it and soemone might wish to do so.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fix the follwing for 3945:
1. Fix direct scan by make sure we set one_direct_scan only when the
mac80211 ask for direct scan.
2. Fix mac_stop and mac_remove_interface calles, we make sure we cancel any
scan and disassoc on these call
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following for 3945:
1. Make sure we cancel scan if RXON command is called.
2. Call scan abort on scan watchdog.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following problems for 4965:
1. Fix direct scan by make sure we set one_direct_scan only when the
mac80211 ask for direct scan.
2. Fix mac_stop and mac_remove_interface calles, we make sure we cancel any
scan and disassoc on these call.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix the following:
1. make sure we are not scanning before we call REPLY_RXON
2. set RXON_FILTER_ASSOC_MSK only after we receive association response
3. call scan abort on scan watchdog instead of restart
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removeis TSF flag from probe request. TSF should be added only to
probe response.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows rtl8187 to receive multicast frames if requested.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (41 commits)
ACPICA: hw: Don't carry spinlock over suspend
ACPICA: hw: remove use_lock flag from acpi_hw_register_{read, write}
ACPI: cpuidle: port idle timer suspend/resume workaround to cpuidle
ACPI: clean up acpi_enter_sleep_state_prep
Hibernation: Make sure that ACPI is enabled in acpi_hibernation_finish
ACPI: suppress uninitialized var warning
cpuidle: consolidate 2.6.22 cpuidle branch into one patch
ACPI: thinkpad-acpi: skip blanks before the data when parsing sysfs
ACPI: AC: Add sysfs interface
ACPI: SBS: Add sysfs alarm
ACPI: SBS: Add ACPI_PROCFS around procfs handling code.
ACPI: SBS: Add support for power_supply class (and sysfs)
ACPI: SBS: Make SBS reads table-driven.
ACPI: SBS: Simplify data structures in SBS
ACPI: SBS: Split host controller (ACPI0001) from SBS driver (ACPI0002)
ACPI: EC: Add new query handler to list head.
ACPI: Add acpi_bus_generate_event4() function
ACPI: Battery: add sysfs alarm
ACPI: Battery: Add sysfs support
ACPI: Battery: Misc clean-ups, no functional changes
...
Fix up conflicts in drivers/misc/thinkpad_acpi.[ch] manually
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because rt2x00 implements the residual calculation different from what the
legacy code does (i.e. scaled values), we need to adjust the residual check.
Again, we are only mimicking the behaviour of the ralink driver without
actually knowing what we do :-(
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes setting of rates in probe request used in
HW scan. The bug was reported by Helmut Schaa <hschaa@suse.de>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an uninitialized variable in drivers/net/wireless/b43/main.c::b43_start().
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes base rate needed for fixed rate operation in A band
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
