hp6xx requires some additional IRQs that aren't currently enabled in
the SH7709 setup code. Wire them up.
Signed-off-by: Takashi YOSHII <takashi.yoshii.ze@hitachi.com>
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds more full-featured support for the SH7722 Solution Engine.
Previously this was using the generic board, and lacked most of the
peripheral support.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was done in cpuinfo, but with the number of clocks
growing, it makes more sense to place this in a different proc entry.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up SH7705 CPU support and the SE7705 board
for some of the recent changes.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7722 (MobileR) to the clock framework.
Signed-off-by: dmitry pervushin <dimka@nomadgs.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we've been handling udivdi3 references and wrapping
them in to div64_32() automatically. This doesn't get a lot of
use, however, and as akpm noted in the recent thread on l-k:
http://lkml.org/lkml/2007/2/27/241
we're better off simply ripping it out and going the do_div()
route if there happen to be any places that need it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks some of the node 0 bootmem initialization in
preparation for discontigmem and sparsemem support.
ARCH_POPULATES_NODE_MAP is switched to as a result of this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Each board sets the total number of IRQs that it's interested in via
the machvec. Previously we cared about the off vs on-chip IRQ range,
but any code relying on that is long dead. Set NR_IRQS to something
sensible given the vector range, and allow boards to cap it if they
really care.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wire up GENERIC_BUG for SH. This moves off of the special bug
frame and on to the generic struct bug_entry. Roughly the same
semantics are retained, and we can kill off some of the verbose
BUG() reporting code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7780 has a speculative execution mode where it can speculatively
perform an instruction fetch for subroutine returns, this allows it
to be enabled. There are some various pitfalls associated with this
mode, so it's left as depending on CONFIG_EXPERIMENTAL and not
enabled by default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The kgdb thread support is woefully out of date (it predates
the pidhash), and needs a complete rewrite before it's useful
again. Just rip it out entirely.
Updating the unified kgdb stub is a more worthwhile endeavour
for anyone that happens to be interested in this, at present
it's just limping along.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Let's allow page-alignment in general for per-cpu data (wanted by Xen, and
Ingo suggested KVM as well).
Because larger alignments can use more room, we increase the max per-cpu
memory to 64k rather than 32k: it's getting a little tight.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
__sdivsi3_i4i, __udiv_qrnnd_16, and __udivsi3_i4i don't exist
outside of the ST compiler, so kill them off.
This causes compile failures with other GCC4 compilers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-3 and SH-4 were trampling the register, and SH-2 wasn't even
setting it in the first place. This ended up with some rather
broken behaviour in the sysrq show_regs().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The code for performing the calculation was only in the SH-4 probe
path, move it out to the common path so the other parts get this
right too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I run a preemptive kernel-2.6.20 for SH7780, a created
kthread(pdflush) can not exit by do_exit() in kernel_thread_helper. I
think that the created kthread should have a room for 'struct pt_regs'
space on the stack top, because __switch_to() will refer to the space as
follows using 'regs = task_pt_regs(prev)' and next condition may be true.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a missing return in do_signal() that caused the saved
sigmask to be written back after having successfully delivered
the signal.
Signed-off-by: Ryusuke Sakato <sakato@hsdv.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This takes care of tearing down the UBC so it's not inadvertently
left configured at the next context switch time. Failure to do
this results in spurious SIGTRAPs in certain debug sequences.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This tidies up some of the rts7751r2d mess and gets it booting
again. Update the defconfig, too.
Signed-off-by: Masayuki Hosokawa <hosokawa@ace-jp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This ended up causing problems for older parts (particularly ones
using PTEA). Revert this for now, it can be added back in once it's
had some more testing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rename the existing flush routines to local_ variants for use by
the IPI-backed global flush routines on SMP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are a lot of bogus cpu_data-> references that only end up working
for the boot CPU, convert these to current_cpu_data to fixup SMP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was implemented using a global cache, cache
this per-CPU instead and bump up the number of context IDs to
match NR_CPUS.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch does the following:
- remove the make_ipr_irq stuff from dma-sh.c and replace it
with a simple channel<->irq mapping table.
- add DMTEx_IRQ constants for sh4 cpus
- fix sh7751 DMAE irq number
The SH7780 uses the same IRQs for DMA as other SH4 types, so
I put the constants on top of the dma.h file.
Other CPU types need to #define their own DMTEx_IRQ contants
in their appropriate header.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
handle_BUG() uses TRAPA_BUG_OPCODE which is only defined for
CONFIG_BUG, make sure it's not built when CONFIG_BUG=n.
Signed-off-by: Nobuhiro Iwamatsu <hemamu@t-base.ne.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the lazy dcache handling to the model described in
Documentation/cachetlb.txt and drops the ptep_get_and_clear() hacks
used for the aliasing dcaches on SH-4 and SH7705 in 32kB mode. As a
bonus, this slightly cuts down on the cache flushing frequency.
With that and the PTEA handling out of the way, the update_mmu_cache()
implementations can be consolidated, and we no longer have to worry
about which configuration the cache is in for the SH7705 case.
And finally, explicitly disable the lazy writeback on SMP (SH-4A).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were a few more things that needed fixing up, namely THREAD_SIZE
and the TLB miss handler where certain PTRS_PER_PGD == PTRS_PER_PTE
assumptions were being made.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up shmin (and SH7706/SH7708) IPR support for some of the
recent API changes.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows the baud rate for earlyprintk for sh4 without the
standard BIOS to be set via the command line. This uses the same
format as i386 and x86_64, which is:
earlyprintk=serial,ttySC1,38400
The second parameter (ttySC1 above) is usually the console device
name or the io address of the serial port. I allow that to be
specified but ignore it in order to keep the format the same as
i386/x86_64.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This rips out most of the needlessly complicated sh_bios and kgdb
trap handling, and forces it all through a common fast dispatch path.
As more debug traps are inserted, it's important to keep them in sync
for all of the parts, not just SH-3/4.
As the SH-2 parts are unable to do traps in the >= 0x40 range, we
restrict the debug traps to the 0x30-0x3f range on all parts, and
also bump the kgdb breakpoint trap down in to this range (from 0xff
to 0x3c) so it's possible to use for nommu.
Optionally, this table can be padded out to catch spurious traps for
SH-3/4, but we don't do that yet..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update all arch/*/kernel/vmlinux.lds.S to not include space for initramfs
when CONFIG_BLK_DEV_INITRAMFS is not selected. This saves another 4 kbytes
on most platfoms (some reserve PAGE_SIZE for initramfs).
Signed-off-by: Jean-Paul Saman <jean-paul.saman@nxp.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-apm:
[APM] SH: Convert to use shared APM emulation.
[APM] MIPS: Convert to use shared APM emulation.
[APM] ARM: Convert to use shared APM emulation.
[APM] Add shared version of APM emulation
This adds in support for the BUG() trap on SH-2.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
