Use the correct wake-up enable register, and make it
work with 34xx also.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
0 is a valid GPIO number, use a negative number to specify, that this camera
doesn't have a GPIO for bus-width switching.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The second clk_deny_idle instance should be clk_allow_idle instead.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch makes do_hw_reset the default reboot behavior when nothing
else matches. This restores reboot functionality on gumstix basix
devices where reboot=cold is the default boot argument.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original incorrect configuration caused GPIO79_nCS_3 being overriden,
thus resulted in the NAND flash not being detected. The real PSKTSEL pin
is on GPIO104 instead of GPIO79.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
FLASH_* and EPROM_* constants are unused, and clash with drivers:
drivers/atm/ambassador.h:257:1: warning: "FLASH_BASE" redefined
drivers/atm/ambassador.h:258:1: warning: "FLASH_SIZE" redefined
drivers/atm/iphase.h:332:1: warning: "EPROM_SIZE" redefined
so remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mm/dma-mapping.c: In function `dma_sync_sg_for_cpu':
arch/arm/mm/dma-mapping.c:588: warning: statement with no effect
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Mikael Pettersson reported:
The 2.6.28-rc kernels fail to detect PCI device 0000:00:01.0
(the first ethernet port) on my Thecus n2100 XScale box.
There is however still a strange "ghost" device that gets partially
detected in 2.6.28-rc2 vanilla.
The IOP321 manual says:
The user designates the memory region containing the OCCDR as
non-cacheable and non-bufferable from the IntelR XScaleTM core.
This guarantees that all load/stores to the OCCDR are only of
DWORD quantities.
Ensure that the OCCDR is so mapped.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Same fix as commit c7cf72dcad: when 'start' and 'end' are less than a
cacheline apart and 'start' is unaligned we are done after cleaning and
invalidating the first cacheline.
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When 'start' and 'end' are less than a cacheline apart and 'start' is
unaligned we are done after cleaning and invalidating the first
cacheline. So check for (start < end) which will not walk off into
invalid address ranges when (start > end).
This issue was caught by drivers/dma/dmatest.
2.6.27 is susceptible.
Cc: <stable@kernel.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As a result of the ptebits changes, we ended up marking device mappings
as normal memory on ARMv7 CPUs, resulting in undesirable behaviour with
serial ports and the like. While reviewing the section mapping table
entries, other errors in the memory type settings for devices were
detected and confirmed to prevent Xscale3 platforms booting.
Tested on:
OMAP34xx (ARMv7),
OMAP24xx (ARMv6),
OMAP16xx (ARM926T, ARMv5),
PXA311 (Xscale3),
PXA272 (Xscale),
PXA255 (Xscale),
IXP42x (Xscale),
S3C2410 (ARM920T, ARMv4T),
ARM720T (ARMv4T)
StrongARM-110 (ARMv4)
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Ben Dooks <ben-linux@fluff.org>
Tested-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of 73bdf0a60e, the kernel needs
to know where modules are located in the virtual address space.
On ARM, we located this region between MODULE_START and MODULE_END.
Unfortunately, everyone else calls it MODULES_VADDR and MODULES_END.
Update ARM to use the same naming, so is_vmalloc_or_module_addr()
can work properly. Also update the comment on mm/vmalloc.c to
reflect that ARM also places modules in a separate region from the
vmalloc space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
this patch adds asoc audio driver for pxa27x based Palm PDAs. I tested it for
palmtx, t5 and ld, it should work with palmz72 as well (slapin, please test).
I sent it here some time ago, but now I got to fixing bugs in it. It should
be somehow mostly ok and ready for applying.
[Converted to use snd_soc_dapm_nc_pin() and bool Kconfig -- broonie]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On omap24xx, INTCPS_SIR_IRQ_OFFSET bits [6:0] contains the current
active interrupt number.
However, on 34xx INTCPS_SIR_IRQ_OFFSET bits [31:7] also contains the
SPURIOUSIRQFLAG, which gets set if the interrupt sorting information
is invalid.
If the SPURIOUSIRQFLAG bits are not ignored, the interrupt code will
occasionally produce a bunch of confusing errors:
irq -33, desc: c02ddcc8, depth: 0, count: 0, unhandled: 0
->handle_irq(): c006f23c, handle_bad_irq+0x0/0x22c
->chip(): 00000000, 0x0
->action(): 00000000
Fix this by masking out only the ACTIVEIRQ bits. Also fix a
confusing comment.
Signed-off-by: Tony Lindgren <tony@atomide.com>
debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Comparing to PATCH v1, because clk_debugfs_init is included in
"#if defined CONFIG_DEBUG_FS", we only need to check NULL return.
Thanks Li Zefan <lizf@cn.fujitsu.com>
debugfs_create_u8() and other function's return value's checking method are
also fixed in this patch.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix these compiler warnings:
gpmc.c: In function 'gpmc_init':
gpmc.c:432: warning: 'return' with a value, in function returning void
gpmc.c:439: warning: 'return' with a value, in function returning void
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2.6.28-rc tightened up the ELF architecture checks on ARM. For
non-EABI it only allows VFP if the hardware supports it. However,
the kernel fails to also inspect the soft-float flag, so it
incorrectly rejects binaries using soft-VFP.
The fix is simple: also check that EF_ARM_SOFT_FLOAT isn't set
before rejecting VFP binaries on non-VFP hardware.
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c_board_info array was filled incorrectly.
Due to circumstances, the way it is filled works.
This patch fills array properly.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mx31ads_defconfig compilation failed with
arch/arm/mach-mx3/mx31ads.c: In function 'mxc_init_imx_uart':
arch/arm/mach-mx3/mx31ads.c:102: error: 'mxc_uart_device0' undeclared (first use in this function)
arch/arm/mach-mx3/mx31ads.c:102: error: (Each undeclared identifier is reported only once
arch/arm/mach-mx3/mx31ads.c:102: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-mx3/mx31ads.o] Error 1
Add missing include
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Data register holds the value we have written to a gpio. To
get the input value we must read the Pad Status Register MX3 (or Sample
Status register in MX1/2 terms)
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The internal devices of the MX3 Processor have to be mapped
MT_DEVICE_NONSHARED devices, otherwise cache corruptions occur.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the arm architecture.
DaVinci is skipped on purpose to simplify the merge process for patches
switching it over to use gpiolib as per request by David Brownell.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix compilation of sharpsl_pm when CONFIG_PM in unselected.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The internal devices of the MX3 Processor have to be mapped
MT_DEVICE_NONSHARED devices, otherwise cache corruptions occur.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
corgi_lcd has symbol conflict with corgi_bl driver.
Fix it by renaming common symbol in new corgi_lcd driver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Commit 40df2d1d "[ARM] Update Xscale and Xscale3 PTE mappings" was
fingered by git-bisect for a boot failure on iop13xx. The change made
L_PTE_MT_WRITETHROUGH mappings L2-uncacheable. Russell points out that
this mapping is used for the vector page. Given the regression, and the
fact this page is used often, restore the old behaviour.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
