The packet length checks in ipoib are broken: we add 4 bytes (IPoIB
encapsulation header) when sending a packet, not 20 bytes (hardware
address length) to each packet. Therefore, if connected mode is
enabled so that the interface MTU is larger than the multicast MTU,
IPoIB may end up trying to send too-long multicast packets. For
example, multicast is broken if a message of size 2048 bytes is sent
on an interface with UD MTU 2048, because 2048 is bigger than the real
limit of 2044 but the code tests against the wrong limit of 2060.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=418>,
submitted by Scott Weitzenkamp <sweitzen@cisco.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The connected mode code added the possibility that an neigh struct
gets freed in the list_for_each_entry() loop in path_rec_completion(),
which causes a use-after-free. Fix this by changing to the _safe
variant of the list walking macro.
This was spotted by the Coverity checker (CID 1567).
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA scaling code must not depend on register_cpu_notifier() if
CONFIG_HOTPLUG_CPU is not set, so put all related code into #ifdefs.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's a race between ipoib_mcast_leave() and ipoib_mcast_join_finish()
where we can try to detach from a multicast group before we've
attached to it. Fix this by reordering the code in ipoib_mcast_leave
to free the multicast group first, which waits for the multicast
callback thread (which calls ipoib_mcast_join_finish()) to complete
before detaching from the group.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The sense of the time_after_eq() test in ipoib_cm_stale_task() is
reversed so that only non-stale connections are reaped. Fix this by
changing to time_before_eq().
Noticed by Pradeep Satyanarayana <pradeep@us.ibm.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Do netif_carrier_on() right after the IPv4 broadcast multicast group
is joined, rather than waiting for all of the initial set of multicast
group joins to finish. This allows at least IPv4 traffic to limp
along on broken fabrics where not all multicast groups can be joined.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the returned error code to ENOMEM if the connection event
backlog is full. This prevents the ib_cm from issuing a reject
on the connection, which can allow retries to succeed.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix memory region permission problems:
- remove useless and redundant iwch_mem_perms enum.
- create ib_to_tpt_access_rights() for mapping ib access rights
to T3 TPT permissions.
- create ib_to_mwbind_access_rights() for mapping ib access rights
to T3 MWBIND WR permissions.
- fix up the mem reg code to utilize the new functions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only print one AE error for a given connection in the kernel log.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stop the endpoint timer when the MPA exchange is aborted by the peer.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change iwch_destroy_qp() to always move the QP to ERROR and let
iwch_modify_qp() decide what to do.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes for "normal close" failures:
- Start normal close timer when moving to CLOSING state.
- Handle ABORTING state in close_con_rpl().
- Stop timer correctly on abort during a normal close.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cxgb3 uses dma_alloc_coherent() et al. thus needs linux/dma-mapping.h
include in order to build reliably.
Noticed on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct rdma_bind_list fields for hlist are not being initialized,
resulting in a corrupted list. Fix this by using kzalloc() to make
sure all pointers are NULL.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the consumer rejects the connection we end up under-referencing the
endpoint structure. The fix is to call iwch_ep_disconnect() instead
of the low level disconnect functions so that the endpoint close timer
is started correctly.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The garbled logic in mthca_alloc_memfree() causes it to return 0, even
if it fails to allocate all doorbell records. Fix it to return -ENOMEM
when it fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes two issues reported by Roland Dreier and Christoph Hellwig:
- Mismatched sync/locking between completion handler and destroy cq We
introduced a counter nr_events per cq to track number of irq events
seen. This counter is incremented when an event queue entry is seen
and decremented after completion handler has been called regardless
if scaling code is active or not. Note that nr_callbacks tracks
number of events assigned to a cpu and both counters can potentially
diverge.
The sync between running completion handler and destroy cq is done
by using the global spin lock ehca_cq_idr_lock.
- Replace yield by wait_event on the counter above to become zero.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An asynchronous event carries the port number that the event occurred
on, so there's no reason for an IPoIB interface to process an event
associated with a different local HCA port.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If path_rec_completion() is passed a non-NULL path record pointer
along with an unsuccessful status value, the tracing code incorrectly
prints the (invalid) DLID from the path record rather than the more
interesting status code. The actual logic of the function correctly
uses the path record only if the status indicates a successful lookup.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stop the ep timer in ec_status() if the status indicates a
bad close.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- don't mark static functions in C files as inline - gcc should know
best whether inlining makes sense
- never compile the unused cxio_dbg.c
- make the following needlessly global functions static:
- cxio_hal.c: cxio_hal_clear_qp_ctx()
- iwch_provider.c: iwch_get_qp()
- remove the following unused global functions:
- cxio_hal.c: cxio_allocate_stag()
- cxio_resource.: cxio_hal_get_rhdl()
- cxio_resource.: cxio_hal_put_rhdl()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cm_device references an ib_device, which already contains the node_guid.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The rdma_cm requires that path records be reversible. Set the
reversible bit when issuing an path record query.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hop_limit value in the ah_attr should be 0xFF, not the value read
from the received GRH (which should be 0). See 13.5.4.4 in the 1.2 IB
spec.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If no matching PD is found in ib_uverbs_reg_mr(), then the function
jumps to err_release without setting the return value ret. This means
that ret will hold the return value of the call to ib_umem_get() a few
lines earlier; if the function reaches the point where it looks for
the PD, we know that ib_umem_get() must have returned 0, so
ib_uverbs_reg_mr() ends up return 0 for a bad PD ID. Fix this by
setting ret to -EINVAL before jumping to the exit path when no PD is
found.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that low-level drivers handle the conversion from an absolute rate
to a relative rate, there's no need for the IPoIB driver to keep track
of the local port's data rate.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid the overhead of freeing/reallocating and mapping/unmapping for
DMA pages that have not been written to by hardware.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes the needlessly global functions mthca_tavor_write_mtt_seg()
and mthca_arbel_write_mtt_seg() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The static rate from the path record should be put into the address
vector -- a long time ago the rate in the address attributes needed to
be a relative rate, which required more munging, but now that the
conversion from absolute to relative is done in the low-level driver,
it's easy for ib_init_ah_from_path() to put the absolute rate in.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend rdma_cm to support multicast communication. Multicast support
is added to the existing RDMA_PS_UDP port space, as well as a new
RDMA_PS_IPOIB port space. The latter port space allows joining the
multicast groups used by IPoIB, which enables offloading IPoIB traffic
to a separate QP. The port space determines the signature used in the
MGID when joining the group. The newly added RDMA_PS_IPOIB also
allows for unicast operations, similar to RDMA_PS_UDP.
Supporting the RDMA_PS_IPOIB requires changing how UD QPs are initialized,
since we can no longer assume that the qkey is constant. This requires
saving the Q_Key to use when attaching to a device, so that it is
available when creating the QP. The Q_Key information is exported to
the user through the existing rdma_init_qp_attr() interface.
Multicast support is also exported to userspace through the rdma_ucm.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB SA tracks multicast join/leave requests on a per port basis and
does not do any reference counting: if two users of the same port join
the same group, and one leaves that group, then the SA will remove the
port from the group even though there is one user who wants to stay a
member left. Therefore, in order to support multiple users of the
same multicast group from the same port, we need to perform reference
counting locally.
To do this, add an multicast submodule to ib_sa to perform reference
counting of multicast join/leave operations. Modify ib_ipoib (the
only in-kernel user of multicast) to use the new interface.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_cm_alloc_rx_skb() might be called from IRQ context, so it must
use dev_kfree_skb_any(), not kfree_skb().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For T3B devices, mark user QP in error once we transition
to TERMINATE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iwcm iw_cm_id destruction race condition fixes:
- iwcm_deref_id() always wakes up if there's another reference.
- clean up race condition in cm_work_handler().
- create static void free_cm_id() which deallocs the work entries and then
kfrees the cm_id memory. This reduces code replication.
- rem_ref() if this is the last reference -and- the IWCM owns freeing the
cm_id, then free it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Acked-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the port phys state as returned from ehca_query_port() to LINK_UP.
ehca actually represents a logical HCA, whose phys/link state always
is LINK_UP.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow users to en/disable scaling code when loading ib_ehca module,
rather than requiring the module to be rebuilt to change the setting.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a race condition in find_next_cpu_online() and some other locking
issues in ehca scaling code.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
