The default chainmask for AR9280 is 3, so handle that when setting
the supported MCS rates. Also, check for the HW supported chainmask
when choosing single/dual stream.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Versioning for ath9k is pointless we have kept it at 0.1
since the initial release so its meaningless. We put more emphasis
on kernel release or dated wireless-testing master tag
as per John's tagging.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix AR9285 specific noise floor reads and initialize tx and rx
chainmask during reset. This along with the following earlier
patches of ath9k fixes an issue with association noticed in
noisy environment.
ath9k: Fix typo in chip version check
ath9k: Remove unnecessary gpio configuration in ath9k_hw_reset()
ath9k: Fix bug in NF calibration
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With debugging enabled and with ATH_DBG_REGULATORY
selected we wouldn't get the full print out of one line,
reason is we used "," instead of nothing to separate two
lines.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add vendor ID for AMBIT and use it to set the ath5k LED gpio.
base.c:
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dynamically control the log verbosity with a module parameter.
This enables us to dynamically enable debugging messages (or disable
info, warn, error messages) via module parameter or /sys/module/b43/parameters/verbose.
This increases the module size by about 3k. But in practice it reduces the
module size for the user, because some distributions ship the b43 module
with CONFIG_B43_DEBUG set, which increases the module by about 15k.
So with this patch applied, distributions should really _disable_ CONFIG_B43_DEBUG.
There is no reason to keep it in a production-release kernel.
So we have a net reduction in size by about 12k.
This patch also adds a printk of the wireless core revision, so people
don't have to enable SSB debugging to get the wireless core revision.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the mac80211 high level code to access the TSF. This is e.g. needed for BSSID merges in the IBSS mode.
The second version adds locking and removes the now unnecessary debugfs entries.
Thanks to Michael Buesch! :)
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables low-level driver independent debugging of the TSF and remove the driver specific things of ath5k and ath9k from the debugfs.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix compilation warning in printk formatting
iwl_tx_queue_alloc function.
Cleanup the code a bit on the way.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix compile warning for non-debug builds:
drivers/net/wireless/b43/phy_g.c: In function ‘b43_gphy_op_recalc_txpower’:
drivers/net/wireless/b43/phy_g.c:3195: warning: unused variable ‘dbm’
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_wep_key() and set_wep_key() combind both get/set of the actual WEP
key and get/set of the transmit index into the same functions. Split those
out so it's clearer what is going one where. Add error checking to WEP
key hardware operations too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do the computation once at init time; don't ask the hardware
every time.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The capability register has to be read for other (upcoming) stuff, so fold
the WPA test function back into _init_airo_card() and move the netdevice
registration stuff above it so that the netdevice has a name by the time
the card's capabilities are printed out.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split each specific interrupt-time task out into its own function to
make airo_interrupt() actually readable.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This pach make use of 39 own scan probe mask
the variables or of different types
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent host command routines merge, we can now look at the various
host command helpers and get rid of the duplicated ones.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to be in sync with the agn code, we're ading a fw_restart3945 module
parameter to iwl3945.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl_priv antenna field is useless as we can simply use the corresponding
mod_params antenna field.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IWL3945_DEBUG is pointless and obsolete. We already have an IWLWIFI_DEBUG
symbol, that needs to be set if we actually want to get 3945 debug (see
iwl-debug.h).
Thus, we can simply get rid of this symbol.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By removing the init_rates() routine outside of the init_geos() one, we can
share the geos routines between 3945 and agn.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By adding the eeprom ops to the 3945 code, we can now use the iwlcore eeprom
routines (defined in iwl-eeprom.c).
We also removed the heavy eeprom39 reference from iwl_priv and use the eeprom
pointer instead.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By adding an additional hw_params (tfd_size) and a new iwl_lib ops (txq_init),
we can now use the iwlcore TX queue management routines.
We had to add a new hw_params because we need to allocate the right DMA buffer
for TFDs, and those have a different sizes depending if you're on 3945 or agn.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having both tfds and tfds39, we can just have a void *tfds.
It makes the tx_queue structure nicer, and the code cleaner. It also helps
with further TX queues management code merging.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A lot of the scanning related code is duplicated between 3945 and agn. Let's
use the iwlcore one and get rid of the 3945.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can define this iwl_lib ops for 3945, as this would help us cleaning the
scanning code.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force use of chains B and C (0x6) for Rx for 4965
Avoid A (0x1) because of its off-channel reception on A-band.
Signed-off-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sets driver in monitor mode through configuring the
RX filters. We cannot trust priv->iw_mode to be accurate
regarding monitor mode as iw_mode is only set in add_interface,
which is not called by mac80211 when in monitor mode.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First probe for proprietary firmware and then probe for opensource firmware.
This way around it's a win-win situation.
1) If proprietary fw is available, it will work.
2) If opensource firmware is available, but no proprietary (Distros can only ship open fw)
it might work.
3) If both open and proprietary are available, it will work, because it selects
the proprietary. We currently don't prefer the open fw in this case, because it doesn't
work on all devices. It would introduce a regression otherwise.
The remaining FIXMEs in this patch are harmless, because they only matter on multiband
devices, which are not implemented yet anyway.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current code for the RTL8187 is not returning valid retry information, thus the
rate-setting mechanism is not functioning. As a further complication, this info
is only obtained by reading a register, which cannot be read while in interrupt
context.
This patch implements the TX status return to mac80211 through the use of a
work queue.
One additional problem is that the driver currently enables the rate fallback
mechanism of the device, which conflicts with the mac80211 rate-setting
algorithm. This version of the patch disables rate fallback.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The receive queue depth in rtl8187 may not be long enough to keep
the pipe full.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rtl8187_add_interface(), the mutex that protects the data in struct
rtl8187_priv does not include all references to that structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
if_cs_poll_while_fw_download() returned the number of iterations
remaining on success, which in turn got returned as the value from
if_cs_prog_real() and if_cs_prog_helper(). But since if_cs_probe()
interprets non-zero return values from firmware load functions as an
error, this sometimes caused spurious firmware load failures.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With mac80211 handling all open interfaces during
suspend and resume we can simplify suspend/resume
within rt2x00lib.
The only thing rt2x00 needs to do is free up memory
during suspend and bring back the minimal required
components during resume.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add extra security to the drivers for firmware loading,
check the firmware file length before uploading it to
the hardware. Incorrect lengths might indicate a firmware
upgrade (which is not yet supported by the driver) or
otherwise incorrect firmware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "rev" field in chipset definition is an u32,
which means that rt2x00_rev() which returns that field
should be of the same type.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of chainmasks for AR9285 weren't being
setup when running NF calibration.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dual stream capability must be registered only when the
hardware supports it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 based devices support only single stream MCS rates.
This patch fixes a bug where dual stream stream rates were
also being registered.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an ath9k specific entry to read, write and reset the TSF into the debugfs, like in ath5k. This makes debugging the IBSS handling of wifi drivers _much_ easier.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the ath5k specific entry in the debugfs to read and reset the TSF value, to allowing write it, too. This makes debugging the IBSS handling of wifi drivers _much_ easier.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that cfg80211 has its own regulatory infrastructure we can
condense ath9k's regulatory code considerably. We only keep data
we need to provide our own regulatory_hint(), reg_notifier() and
information necessary for calibration.
Atheros hardware supports 12 world regulatory domains, since these
are custom we apply them through the the new wiphy_apply_custom_regulatory().
Although we have 12 we can consolidate these into 5 structures based on
frequency and apply a different set of flags that differentiate them on
a case by case basis through the reg_notifier().
If CRDA is not found our own custom world regulatory domain is applied,
this is identical to cfg80211's except we enable passive scan on most
frequencies.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers without firmware can also have custom regulatory maps
which do not map to a specific ISO / IEC alpha2 country code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k driver didn't use set_rts_threshold or use_cts_prot, and also
didn't check the IEEE80211_TX_RC_USE_{RTS_CTS,CTS_PROTECT} RC flags.
Tell the hardware about these so RTS/CTS will work, and so the device
will work better in mixed b/g environments.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k previously ignored TX_RC_SHORT_PREAMBLE and did not use
config->use_short_preamble, so the long preamble was always
used for transmitted packets.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_softc->led_off hasn't been used since commit
3a078876ca, "convert LED code to use
mac80211 triggers."
Changes-licensed-under: 3-Clause-BSD
Reported-by: Tobias Doerffel <tobias.doerffel@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
