Commit Graph

5 Commits

Author SHA1 Message Date
Shaohua Li
a13db56624 [PATCH] CPU hotplug: fix hpet sectioning
With hpet enabled, cpu hotplug uses some routines marked with __init.

Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-25 16:24:28 -07:00
Andrew Morton
a3a255e744 [PATCH] x86: cpu_khz type fix
x86_64's cpu_khz is unsigned int and there is no reason why x86 needs to use
unsigned long.

So make cpu_khz unsigned int on x86 as well.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 09:45:11 -07:00
Venkatesh Pallipadi
8a9e1b0f56 [PATCH] Platform SMIs and their interferance with tsc based delay calibration
Issue:
Current tsc based delay_calibration can result in significant errors in
loops_per_jiffy count when the platform events like SMIs
(System Management Interrupts that are non-maskable) are present. This could
lead to potential kernel panic(). This issue is becoming more visible with 2.6
kernel (as default HZ is 1000) and on platforms with higher SMI handling
latencies. During the boot time, SMIs are mostly used by BIOS (for things
like legacy keyboard emulation).

Description:
The psuedocode for current delay calibration with tsc based delay looks like
(0) Estimate a value for loops_per_jiffy
(1) While (loops_per_jiffy estimate is accurate enough)
(2)   wait for jiffy transition (jiffy1)
(3)   Note down current tsc (tsc1)
(4)   loop until tsc becomes tsc1 + loops_per_jiffy
(5)   check whether jiffy changed since jiffy1 or not and refine
loops_per_jiffy estimate

Consider the following cases
Case 1:
If SMIs happen between (2) and (3) above, we can end up with a
loops_per_jiffy value that is too low. This results in shorted delays and
kernel can panic () during boot (Mostly at IOAPIC timer initialization
timer_irq_works() as we don't have enough timer interrupts in a specified
interval).

Case 2:
If SMIs happen between (3) and (4) above, then we can end up with a
loops_per_jiffy value that is too high. And with current i386 code, too
high lpj value (greater than 17M) can result in a overflow in
delay.c:__const_udelay() again resulting in shorter delay and panic().

Solution:
The patch below makes the calibration routine aware of asynchronous events
like SMIs. We increase the delay calibration time and also identify any
significant errors (greater than 12.5%) in the calibration and notify it to
user.

Patch below changes both i386 and x86-64 architectures to use this
new and improved calibrate_delay_direct() routine.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-23 09:45:08 -07:00
Dave Jones
c5d28fb297 [CPUFREQ] Recalibrate cpu_khz [2/2]
Some cpufreq drivers (at that time, only powernow-k7) need to recalibrate the
cpu_khz at runtime.

Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
2005-05-31 19:03:46 -07:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00