Commit Graph

1810 Commits

Author SHA1 Message Date
Peter Ujfalusi
e5e5b31e8c ASoC: tpa6130a2: TLV mapping for tpa6140a2
Both tpa6130a2, and tpa6140a2 is supported by the
same driver, but the gain dB scaling is different on
the amplifiers.

Provide different mixer control for the chips with correct
TLV mapping.

User space will see:
"TPA6130A2 Headphone Playback Volume" in case of 6130
"TPA6140A2 Headphone Playback Volume" in case of 6140

The way machine drivers are using this amplifier remained
the same.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-04 20:55:01 +01:00
Peter Ujfalusi
ad05c03b1c ASoC: tlv320dac33: Support for turning off the codec
Let the codec to hit OFF instead of STANDBY, when there is no activity.
When the codec is off, than the associated regulator can be also turned
off (if the number of users on the regulator is 0).

After initialization, the codec remains in power off, it is only turned
on for reading the ID registers (also testing the regulators).

The codec power is enabled, when the codec is moving from BIAS_OFF
to BIAS_STANDBY.
The codec is turned off, when it hits BIAS_OFF.

There are few scenarios, which has to be taken care::
1. Analog bypass caused BIAS_OFF -> BIAS_ON
   We need to power on the codec, and do the chip init, but we does not
   need to execute the playback related configuration
2. Playback caused  BIAS_OFF -> BIAS_ON
   We need to power on the codec, and do the chip init, and also we need
   to execute the playback related configuration.
3. Playback start, while Analog bypass is on (BIAS_ON -> BIAS_ON)
   We need to execute the playback related configuration. The codec is
   already on.
4. Analog bypass enable, while playback (BIAS_ON -> BIAS_ON)
   Nothing need to be done.
5. Playback start withing soc power down timeout (BIAS_ON -> BIAS_ON)
   We need to execute the playback related configuration. The codec is
   still on.

Since the power up, and the codec init is optimized, the added overhead
in stream start is minimal.

Withing this patch, the hard_power function is now only doing what it
supposed to: only handle the powers, and GPIO reset line.
The codec initialization and state restore has been moved out.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-03 12:55:54 +01:00
Peter Ujfalusi
0b61d2b9f2 ASoC: tlv320dac33: Manage a pointer for snd_pcm_substream in private structure
As a preparation for supporting codec to be turned off,
when we are in BIAS_STANDBY.

The substream must be easily available in other places than
pcm_* callbacks.

Manage a pointer in _startup, and _shutdown for this.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-03 12:55:48 +01:00
Peter Ujfalusi
239fe55c7f ASoC: tlv320dac33: Revised module loading, and DAC33 ID read
Optimize the way how tlv320dac33 is powered uppon module and
soc initialization.
Also read the DAC33 ID registers, and update the reg_cache
to reflect it.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-03 12:55:48 +01:00
Peter Ujfalusi
ef909d6729 ASoC: tlv320dac33: Optimize power up, and restore
On power up we only need to initialize the codec, and
restore only registers, which are not in either in DAPM
nor in the playback start sequence.
These are mostly gain related registers.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-03 12:55:48 +01:00
Peter Ujfalusi
1b7c9afbfb ASoC: TWL4030: Remove OUTL/R outputs
OUTL/R are leftovers from the original driver, and they
are no longer needed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-03 12:47:30 +01:00
Peter Ujfalusi
7b4c734eea ASoC: TWL4030: AIF/APLL fix in DAPM domain
This patch orders the APLL and AIF power sequence in
case of HiFi (audio in TWL4030 terms) playback/capture.

We also need to make sure that the AIF is running during
playback/capture, when there is no valid DAPM route
available. For this purpose I introduce these virtual
widgets:
/* To have complete playback route all the time */
DAPM_OUTPUT("Virtual HiFi OUT") /* Will keep AIF/APLL enabled */

/* To have complete capture route all the time */
DAPM_INPUT("Virtual HiFi IN") /* Will keep AIF/APLL enabled */

/* To have complete playback route for the voice module */
DAPM_OUTPUT("Virtual Voice OUT") /* Will keep APLL enabled */

The DAPM_SUPPLY widgets for APLL and AIF are placed in a way,
that during any audio activity the needed configuration of AIF
and APLL will be enabled (playback, capture, analog loopback,
digital loopback, and voice activity).

The apll reference counting code has been lifted,
and modified from Liam Girdwood's earlier patch.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-05-03 12:47:29 +01:00
Geert Uytterhoeven
b0b4ce38a5 MIPS: TXx9: Add missing MODULE_ALIAS definitions for TXx9 platform devices
This enables autoloading of the TXx9 sound driver on RBTX4927.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
To: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1101/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-04-30 20:52:40 +01:00
Mark Brown
39b8eab7e7 ASoC: Add WM9090 amplifier driver
The WM9090 is a high performance low power audio subsystem, including
headphone and class D speaker drivers.

Note that this driver is a standalone CODEC driver and so is only
immediately suitable for use with the WM9090 as a standalone sound card
taking line inputs, or with a DAC with no software control.  The pending
ASoC multi-CODEC support will expand the range of systems that can use
the driver, or system-specific adaptations can be made.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-30 16:12:44 +01:00
Liam Girdwood
cf134d5bfb ASoC: tlv320dac33 - disable regulators at i2c remove()
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-28 13:27:18 +01:00
Liam Girdwood
1849235876 ASoC: zoom2 - update DAPM pins
Remove bogus twl4030 pins

Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-28 13:27:18 +01:00
Liam Girdwood
1beb91f004 ASoC: pandora - update DAPM pins
Remove bogus TWL4030 pins.

Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-28 13:27:18 +01:00
Mark Brown
dde3a7e9cb ASoC: Remove redundant WM8960 SYSCLKSEL clkdiv option
The SYSCLK source is automatically managed when configuring the PLL.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-28 11:33:04 +01:00
Takashi Iwai
cb7b76961f Merge branch 'for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc 2010-04-27 15:35:59 +02:00
Jarkko Nikula
07779fdd1a ASoC: tlv320aic3x: Add basic regulator support
This patch adds the TLV320AIC3x supplies and enables all of them for the
entire lifetime of the device.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-27 11:19:23 +01:00
Jarkko Nikula
db13802e51 ASoC: tlv320aic3x: Change bias management semantics
Move PLL enable from BIAS_ON state to BIAS_PREPARE to be pair with
BIAS_STANDBY where PLL is disabled. Remove also old comments about power
control.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-27 11:08:06 +01:00
Jarkko Nikula
d3235c4ac1 ASoC: tlv320aic3x: Remove needless power off from aic3x_set_bias_level
These ADC, DAC and output pin power off commands are needless in
aic3x_set_bias_level since they are not enabled in aic3x_init and they are
defined in aic3x_dapm_widgets so the ASoC DAPM will take care of them
anyway.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-27 11:08:06 +01:00
Jarkko Nikula
c6de6e0300 ASoC: tlv320aic3x: Remove unused version string
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-27 11:08:05 +01:00
Vladimir Zapolskiy
b28528a124 ASoC: UDA134X: Add UDA1345 CODEC support
This patch adds support for Philips UDA1345 CODEC. The CODEC has only
volume control, de-emphasis, mute, DC filtering and power control features.

Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-26 15:28:18 +01:00
Mark Brown
5e5e2bef28 ASoC: Warn on low WM8994 AIFCLK
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-26 15:26:13 +01:00
Mark Brown
759512fbac ASoC: Correct inversion of speaker mixer PCM switch
Reported-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-26 15:24:28 +01:00
Peter Ujfalusi
f57d2cfaad ASoC: tlv320dac33: FIFO caused delay reporting
Delay reporting for the three implemented DAC33 FIFO modes.
DAC33 has FIFO depth status register(s), but it can not be used, since
inside of pcm_pointer we can not send I2C commands.
Timestamp based estimation need to be used. The method of calculating
the delay depends on the active FIFO mode.

Bypass mode: FIFO is bypassed, report 0 as delay

Mode1: nSample fill mode. In this mode I need to use two timestamp
ts1: taken when the interrupt has been received
ts2: taken before writing to nSample register.

Interrupts are coming when DAC33 FIFO depth goes under alarm threshold.

Phase1: when we received the alarm threshold, but our workqueue has
        not been executed (safeguard phase). Just count the played out
        samples since ts1 and subtract it from the alarm threshold
        value.
Phase2: During nSample burst (after writing to nSample register), count
        the played out samples since ts1, count the samples received
        since ts2 (in a burst). Estimate the FIFO depth using these and
        alarm threshold value.
Phase3: Draining phase (after the burst read), count the played out
        samples since ts1. Estimate the FIFO depth using the nSample
        configuration and the alarm threshold value.

Mode7: Threshold based fill mode. In this mode one timestamp is enough.
ts1: taken when the interrupt has been received

Interrupts are coming when DAC33 FIFO depth reaches upper threshold.

Phase1: Draining phase (after the burst), counting the played out
        samples since ts1, and subtract it from the upper threshold
        value.
Phase2: During burst operation. Using the pre calculated time needed to
        play out samples from the buffer during the drain period (from
        upper to lower threshold), move the time window to cover the
        estimated time from the burst start to the current time.
        Calculate the samples played out since lower threshold and also
        the samples received during the same time.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-26 15:16:39 +01:00
Peter Ujfalusi
76f471274d ASoC: tlv320dac33: Calculate the interface speed during bursts
When the DAC33 FIFO is in use the dai interface is running in
much higher speed than the sampling frequency.
Calculate the rate based on the internal base frequency and
the bclk divider.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-26 15:16:33 +01:00
Peter Ujfalusi
4260393e71 ASoC: tlv320dac33: Change magic numbers used in Mode7
Upper and Lower threshold values are used as magic
numbers. Replace them with defines for later use.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-26 15:16:28 +01:00
Peter Ujfalusi
55abb59c9a ASoC: tlv320dac33: Skip calculations in FIFO Bypass mode
There is no need for calculations for FIFO bypass mode.
Just in case set the nsample maximum limit, which
has been done in the calculation phase.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-26 15:16:23 +01:00
Peter Ujfalusi
f4d5932806 ASoC: tlv320dac33: Fix for early interrupt in FIFO Mode1
Alarm threshold interrupt is triggered right after the
playback start.
This interrupt is recieved during the first burst period,
and caused the state machine to write additional nSample
command, which has to be avoided.
To fix this issue move the DAC33 interrupt unmasking
after we configured the PREFILL register with a small
delay.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-26 15:16:18 +01:00
Mark Brown
3a278a0c65 ASoC: Allow reporting of NULL jacks
Follow the core jack implementation and allow reporting on the status
of NULL jacks, avoiding the need to check in detection implementations.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 17:07:10 +01:00
Barry Song
ba0a24e738 ASoC: ad193x: fix typo, delete redundant space
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-23 16:14:57 +01:00
Barry Song
d6bdc0f7fe ASoC: ad193x: fix wrong register setting in ad193x_set_dai_fmt
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-23 16:14:02 +01:00
Mark Brown
7add84aa77 ASoC: Allow unspecified source when stopping WM8994 FLLs
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-22 02:29:01 +09:00
Mark Brown
ee839a2127 ASoC: Tone down debugging for WM8994 class W
It's a little verbose during path changes.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-21 01:41:28 +09:00
Mark Brown
7d48a6acbc ASoC: Set full range of WM8994 FLL Fratio values
Use all the available Fratio values when configuring the WM8994 FLL, not
just 0 and 3, following more complete characterisation of the device
performance.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-21 01:41:27 +09:00
Mark Brown
136ff2a272 ASoC: Support FLL input clock selection on WM8994
The WM8994 FLL can be clocked from one of four inputs, the two MCLKs and
the LRCLK and BCLK of the AIF associated with the FLL. Allow all four
inputs to be used rather than defaulting to MCLK1.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-21 01:41:26 +09:00
Phil Carmody
4f6f22d7be ASoC: da7210: Fencepost error in reg cache read
An index equal to the array size may not be accessed.

Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-21 01:41:26 +09:00
Takashi Iwai
d4a8ca2461 ASoC: missing conversions to snd_soc_codec_*_drvdata()
Conversions to snd_soc_codec_{get|set}_drvdata() were missing in some files
in the previous commit.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-04-20 08:29:19 +02:00
Mark Brown
b2c812e22d ASoC: Add indirection for CODEC private data
One of the features of the multi CODEC work is that it embeds a struct
device in the CODEC to provide diagnostics via a sysfs class rather than
via the device tree, at which point it's much better to use the struct
device private data rather than having two places to store it. Provide
an accessor function to allow this change to be made more easily, and
update all the CODEC drivers are updated.

To ensure use of the accessor the private data structure member is
renamed, meaning that if code developed with older an older core that
still uses private_data is merged it will fail to build.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-17 10:46:22 +09:00
Mark Brown
890c681275 Merge branch 'for-2.6.34' into for-2.6.35 2010-04-17 10:45:54 +09:00
Takashi Iwai
d336905e00 Merge branch 'fix/asoc' into for-linus 2010-04-16 10:03:36 +02:00
Sascha Hauer
8392609969 ASoC: imx-ssi: do not call hrtimer_disable in trigger function
Doing so causes a deadlock, so just signal the timer to stop
using an atomic variable.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-16 01:02:35 +09:00
Sascha Hauer
565a79f74a ASoC: imx-ssi: increase minimum periods to 4
Currently the notification of elapsed periods is not very exact.
Increase minimum periods to 4 as suggested by Liam Girdwood.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-15 10:29:49 +09:00
Marek Vasut
d21e0f4cd1 ASoC: Zipit Z2 WM8750 ASoC driver
This patch adds support for sound through the WM8750 codec on Zipit Z2.
Also, this patch incorporates support for detecting headset jack
insertion through the jack detection API.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-12 11:33:16 +01:00
Bill Gatliff
e135443e21 ASoC: Use SNDRV_PCM_RATE_8000_96000 macro for WM8731
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-12 11:33:04 +01:00
Marek Vasut
6ca0c22ef8 ASoC: WM8750: Convert to new API
Register the WM8750 as a SPI or I2C device. This patch mostly shuffles code
around. Hugely inspired by WM8753 which was already converted.

Also, this patch fixes the Jive and Spitz machine.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-09 12:17:42 +01:00
Sascha Hauer
43a3cec013 ASoC: imx-ssi: Use a hrtimer in FIQ mode
Using a regular timer results in poll times < 1 jiffie with small
buffers, so we loaded the timer with the actual jiffie value. We can
be more accurate using a hrtimer. Also, we have to call
snd_pcm_period_elapsed after playing period_bytes and not
runtime->period_size (which is in samples and not in bytes).

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-08 15:21:05 +01:00
Sascha Hauer
671999cb5d ASoC: imx-pcm-dma-mx2: restart DMA after an error
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-08 15:21:01 +01:00
Sascha Hauer
206b60e189 ASoC: imx-ssi: honor IMX_SSI_DMA flag
When checking if we are DMA capable we have to check for the
IMX_SSI_DMA flag which is already set from platform_data instead
of setting it again when we want to do DMA.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@Slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-08 15:20:57 +01:00
Huang Weiyi
78e4fd26ef ASoC: wm2000: remove unused #include <linux/version.h>
Remove unused #include <linux/version.h>('s) in
  sound/soc/codecs/wm2000.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-08 15:16:00 +01:00
Linus Torvalds
84db18bbeb Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: mixart: range checking proc file
  ALSA: hda - Fix a wrong array range check in patch_realtek.c
  ALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
  ALSA: hda - Enable amplifiers on Acer Inspire 6530G
  ASoC: Only do WM8994 bias off transition from standby
  ASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices
  ASoC: Don't do runtime wm_hubs DC servo updates if using offset correction
  ASoC: Support second DC servo readback method for wm_hubs
  ASoC: Avoid wraparound in wm_hubs DC servo correction
  ALSA: echoaudio - Eliminate use after free
  ALSA: i2c: cleanup: change parameter to pointer
  ALSA: hda - Add MSI blacklist for Aopen MZ915-M
  ASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent ALSA PCM code
  ALSA: hda - Update document about MSI and interrupts
  ALSA: hda: Fix 0 dB offset for Lenovo Thinkpad models using AD1981
  ALSA: hda - Add missing printk argument in previous patch
  ASoC: Fix passing platform_data to ac97 bus users and fix a leak
  ALSA: hda - Fix ADC/MUX assignment of ALC269 codec
  ALSA: hda - Fix invalid bit values passed to snd_hda_codec_amp_stereo()
  ASoC: wm8994: playback => capture
2010-04-07 08:42:25 -07:00
Mark Brown
53a61d967a Merge branch 'for-2.6.34' into for-2.6.35
Conflicts due to context changes next to the backported DMA data change:
	include/sound/soc.h
2010-04-05 19:19:32 +01:00
Mark Brown
8876698406 ASoC: Implement interrupt based WM8994 microphone detection
Support interrupt based microphone bias detection. The WM8994 has two
microphone bias supplies, with detection supported on both. Detection
using GPIOs together with the standard GPIO based jack framework is
already supported via the platform data for the WM8994 core driver.

Note that as well as the microphone bias itself the system clock and
whichever AIF clock is supplying the system clock will need to be
enabled for detection to function.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-05 19:18:12 +01:00
Daniel Mack
5f712b2b73 ALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.

All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.

[Note that this is a backported version for 2.6.34.
 Upstream commit is fd23b7dee]

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-05 19:14:11 +01:00
Mark Brown
d522ffbfb9 ASoC: Only do WM8994 bias off transition from standby
Otherwise we may try to power down multiple times when the using
idle bias off and the driver is removed.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-05 16:20:49 +01:00
Mark Brown
4dcc93d0ed ASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices
The DCS_DATAPATH_BUSY bit used to monitor the completion of DC servo
operations has been deprecated and with some more recente revisions
may perform incorrectly, especially when only analogue bypass paths
are in use. Switch to using readback from the DC servo command
register instead, which is supported for all devices. Without this
unacceptably long timeouts may be observed in some circumstances.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-05 16:20:02 +01:00
Mark Brown
ae9d8607fe ASoC: Don't do runtime wm_hubs DC servo updates if using offset correction
If we need to offset correct the DC servo then don't use runtime
recalibration since that is likely to introduce further offsets
which will be evident on powerdown.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-05 16:19:29 +01:00
Mark Brown
8437f7006b ASoC: Support second DC servo readback method for wm_hubs
More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-05 16:19:09 +01:00
Mark Brown
3fa49e3ad9 ASoC: Avoid wraparound in wm_hubs DC servo correction
If the correction wraps around then a substantial offset would be
introduced.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-05 16:17:39 +01:00
Janusz Krzysztofik
b5442a75de ASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent ALSA PCM code
With recent (2.6.34) chnages in PCM handling, capture stopped working on my
OMAP1510 based Amstrad Delta videophone.

Using 2.6.34-rc2, I was able to correct the problem in 3 different ways:

1. reverting commit 7b3a177b0d,
2. enabling additional jiffies check with
	echo 4 >/proc/asound/card0/pcm0c0/xrun_debug
3. applying the patch below.

Since I wasn't able to reproduce the problem on my i686 PC, I guess the
problem is probably machine specific.

The patch reuses the method for software emulation of missing hardware
pointer, already implemented for playback on OMAP1510. It's possible that
event if a hardware pointer is available for capture on this machine, its
behaviour may be not compatible with what upper layer expects.

If you think the problem may be more general and should be solved differently,
on a higher level, I can try to work more on it if you give me a hint.

If the patch gets accepted, I suggest it goes as a fix in the current release
cycle.

Created and tested against linux-2.6.34-rc2.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-04-02 17:10:25 +01:00
Tejun Heo
5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Mark Brown
2c9504228f Merge branch 'for-2.6.34' into for-2.6.35 2010-03-29 21:03:20 +01:00
Barry Song
9dd7b79a86 ASoC: ad193x: move codec register/unregister to bus probe/remove
The way i've factored out the bus probe and removal functions so
that there's no code in the individual I2C and SPI functions means
that the register() and unregister() functions could just be squashed
into the bus_probe() and bus_remove() functions.

Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-29 21:02:24 +01:00
Graham Gower
fb48e3c6a4 ASoC: Fix passing platform_data to ac97 bus users and fix a leak
[The issue is an attempt to write the pdata without the AC97 device
allocated when using ac97.c - also added a comment in soc-core.c for the
special case for ac97. -- broonie]

Signed-off-by: Graham Gower <graham.gower@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-29 21:00:37 +01:00
Mark Brown
e6ab07ce0f Merge branch 'topic/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 into for-2.6.35 2010-03-29 21:00:04 +01:00
Tejun Heo
923a00427a ASoC: update gfp/slab.h includes
Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-03-29 21:28:43 +02:00
Takashi Iwai
d01e14a6b9 ASoC: Fix file permission of soc/codecs/twl6040.c
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-03-29 09:31:57 +02:00
Stephen Rothwell
68b40cc40a ASoC: TWL6040: use of kzalloc/kfree requires the include of slab.h
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-03-29 09:31:07 +02:00
Stephen Rothwell
1b132ea03e ASoC: update for removeal of slab.h from percpu.h
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-03-29 08:30:23 +02:00
Kuninori Morimoto
cc780d380a ASoC: fsi: Add FSI2 device support
ARM-SHMOBILE series have FIFO-buffered serial interface 2 (FSI2)
device which is advanced version of FSI.
This patch add simple support for it.

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-26 11:17:45 +00:00
Kuninori Morimoto
4a942b457e ASoC: fsi: Add FIFO size calculate
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-26 11:16:27 +00:00
Dan Carpenter
a8462bde78 ASoC: wm8994: playback => capture
Sparse caught that initialize "playback" two times instead of
initializing "capture".

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-24 14:05:28 +00:00
Kuninori Morimoto
10ea76cc25 ASoC: fsi: IRQ related process had be united
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-24 11:16:47 +00:00
Kuninori Morimoto
feb58cffca ASoC: fsi: ensures process inside master lock
Bit operation for fsi_master should be done inside master lock.
But soft-reset/interrupt operation were outside of it.
This patch modify this problem.
It still allow to INT_ST outside-operation on fsi_interrupt,
but it is not problem.
Because this register doesn't need the bit operation.

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-24 11:16:47 +00:00
Kuninori Morimoto
1ad747ca9b ASoC: ak4642: Add enhanced sampling rate
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-23 10:59:11 +00:00
Kuninori Morimoto
0643ce8f42 ASoC: ak4642: Add set_fmt function for snd_soc_dai_ops
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-23 10:59:11 +00:00
Kuninori Morimoto
4b6316b4b1 ASoC: ak4642: Add pll select support
Current ak4642 was not able to select pll.
This patch add support it.
It still expect PLL base input pin is MCKI.
see Table 5 "setting of PLL Mode" of datasheet

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-23 10:59:11 +00:00
Mark Brown
778a76e2db ASoC: Implement WM8994 DAI tristate support
This also adds the first DAI operation for AIF3 so fill out the ID and
the ops for that too.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-23 10:57:11 +00:00
Mark Brown
74511020dd Merge branch 'for-2.6.34' into for-2.6.35 2010-03-22 17:23:46 +00:00
Mark Brown
69266866a5 ASoC: Allow WM8903 mic detect disable and don't force bias on
Don't force enable the microphone bias on WM8903 when doing jack
detection, and don't force enable microphone bias. This allows
platforms to only enable microphone detection when a jack has been
inserted.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22 17:22:56 +00:00
Mark Brown
f06bce9c8c ASoC: Allow disabling of WM835x jack detection
If no report is specified then disable detection. Note that we don't
disable the slow clock, though the power consumption from it should
be negligable. That should be reference counted, ideally through DAPM.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22 17:22:39 +00:00
Mark Brown
2f14430af5 ASoC: Move WM8350 microphone detection bias managment out of driver
Allow machines to control exactly when the bias is turned on and off.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22 17:21:38 +00:00
Mark Brown
5b9e87cccc ASoC: Allow force enabled pins to be disabled
Some systems, such as those with mechanical jack detection, may wish
to force enable a pin (typically mic bias) only some of the time.
Support such systems by having disable_pin() also coveer force enabled
pins.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22 17:21:23 +00:00
Mark Brown
d5021ec9fc ASoC: Add a notifier for jack status changes
Some systems provide both mechanical and electrical detection of jack
status changes. On such systems power savings can be achieved by only
enabling the electrical detection methods when physical insertion has
been detected.

Begin supporting such systems by providing a notifier for jack status
changes which can be used to trigger any reconfiguration.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22 17:20:57 +00:00
Peter Ujfalusi
c96907f21f ASoC: TWL4030: PM fix for output amplifiers
Gain controls on outputs affect the power consumption
when the gain is set to non 0 value.

Outputs with amps have one register to configure the
routing and the gain:
PREDL_CTL (0x25):
bit 0: Voice enable
bit 1: Audio L1 enable
bit 2: Audio L2 enable
bit 3: Audio R2 enable
bit 4-5: Gain (0x0 - power down, 0x1 - 6dB, 0x2 - 0dB, 0x3 - -6dB)

bit 0 - 3: is handled in DAPM domain (DAPM_MIXER)
bit 4 - 5: has simple volume control

If there is no audio activity (BIAS_STANDBY), and
user changes the volume, than the output amplifier will
be enabled.
If the user changes the routing (but the codec remains in
BIAS_STANDBY), than the cached gain value also be written
to the register, which enables the amplifier.

The existing workaround for this is to have virtual
PGAs associated with the outputs, and whit DAPM PMD
the gain on the output will be forced to 0 (off) by
bypassing the regcache.
This failed to disable the amplifiers in several
scenario (as mentioned above).

Also if the codec is in BIAS_ON state, and user modifies
a volume control, which path is actually not enabled, than
that amplifier will be enabled as well, but it will
be not turned off, since there is no DAPM path, which
would make mute it.

To prevent amps being enabled, when they are not
needed, introduce the following workaround:
Track the state of each of this type of output.
In twl4030_write only allow actual write, when the
given output is enabled, otherwise only update
the reg_cache.
The PGA event handlers on power up will write the cached
value to the chip (restoring gain, routing selection).
On power down 0 is written to the register (disabling
the amp, and also just in case clearing the routing).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-22 16:47:12 +00:00
Mark Brown
3cc4e53f86 ASoC: Remove BROKEN from i.MX audio after dependencies merged
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-22 11:17:41 +00:00
Mark Brown
f9b44121b3 Merge commit 'v2.6.34-rc2' into for-2.6.34 2010-03-22 11:17:26 +00:00
Mark Brown
4ca612ebdb Merge branch 'for-2.6.34' into for-2.6.35 2010-03-19 19:39:23 +00:00
Guennadi Liakhovetski
b2dfa62c52 ASoC: remove a card from the list, if instantiation failed
If instantiation of a card failed, we still have to remove it from the
card list on unregistration. This fixes an Oops on Migo-R, triggering,
when after a failed firmware load attempt the driver modules are removed
and re-inserted again.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 19:39:18 +00:00
Daniel Mack
fd23b7dee5 ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.

All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.

Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 19:37:29 +00:00
Mark Brown
093208f5d0 ASoC: Hook up microphone jack detection on 1133-EV1 board
Note that since all the microphones share a bias there is a single
jack exported for all three, even though there are two physical
connectors plus the soldered down silicon mic.  Note also that the SiMic
is always present by default.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-19 14:09:05 +00:00
Barry Song
698c375666 ASoC: change bf5xx-ad1938 machine driver to bf5xx-ad193x machine driver
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 12:47:34 +00:00
Mark Brown
cffce322be ASoC: Unexport AD193x bus probe/remove functions
The export is not needed since the per-bus code lives in the same
module.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-19 12:22:03 +00:00
Barry Song
a1533d94c6 ASoC: rename ad1938 to ad193x and add support for ad1936/7/8/9
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Yi Li <yi.li@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 12:12:16 +00:00
Misael Lopez Cruz
8ecbabd977 ASoC: TWL6040: Add twl6040 codec driver
Initial version of TWL6040 codec driver.

The TWL6040 codec uses a proprietary PDM-based digital audio interface.
Audio paths supported are:

- Input: Main Mic, Sub Mic, Headset Mic, Auxiliary-FM Left/Right
- Output: Headset Left/Right, Handsfree Left/Right

TWL6040 codec supports power-up/down manual and automatic sequence.
Manual sequence is done through a specific register writes sequence.
Automatic sequence is done when the codec is powered-up through the
external AUDPWRON line. The completion of the sequence is signaled
through the audio interrupt.

TWL6040 codec sysclk can be provided by: low-power or high
performance PLL:

- The low-power PLL takes a low-frequency input at 32,768 Hz and
generates an approximate of 17.64 or 19.2 MHz (for 44.1 KHz and 48 KHz
respectively)

- The high-performance PLL generates an exact 19.2 MHz clock signal
from high-frequency input at 12/19.2/26/38.4 MHz.

Low-power playback mode is a special scenario where only headset path
(headset DAC and driver) is active.

For the particular case of headset path, PLL being used defines the
headset power mode: low-power, high-performance.

Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 11:29:33 +00:00
Mark Brown
6937c947d3 ASoC: Bail out of wm_hubs DC servo if calibration fails
We're keeping track of the number of times we've iterated but never
actually using this to bail out if the chip looks stuck.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-03-19 11:17:36 +00:00
Peter Ujfalusi
fdb6b1e195 ASoC: tlv320dac33: Internal clocking changes
During validation of the internal clocking setup it has
been found that the following settings were not configured
in an optimal way:

ASRC_CTRL_A: SRCLKDIV was incorrect, instad of divide ratio 3,
             ratio of 2 has to be used (as the comment stated)
DAC_CTRL_A: Fs = Fsref is the desired configuration instead of
            Fs = Fsref / 1.5

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 11:17:24 +00:00
Peter Ujfalusi
44f497b4e0 ASoC: tlv320dac33: Fix DSP modes
To make DSP_A mode working correctly the data delay should be
configured to 0. DSP_B mode thus can not be used with DAC33,
so remove it.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 11:17:24 +00:00
Mark Brown
27648b2f1c ASoC: Correct typoed Mic2 connections on 1133-EV1 board
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 11:15:42 +00:00
Peter Ujfalusi
299a151f53 ASoC: omap-mcbsp: Add support for Left Justified format
Basic support for Left Justified coding for OMAP McBSP.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 11:14:39 +00:00
Jorge Eduardo Candelaria
9fc71e8f58 ASoC: McPDM: Use tabs for indentation
Indentation in initial support for McPDM driver was converted to spaces.
Use tabs to comply with open source coding-style.

Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-19 11:14:39 +00:00
Guennadi Liakhovetski
da3b062e30 ASoC: SIU driver shall select FW_LOADER
The SIU ASoC driver must load firmware to program the DSP, therefore it
has to select FW_LOADER in its Kconfig entry.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-18 11:31:13 +00:00
Barry Song
f4bee1bb00 ASoC: soc-cache: let reg be AND'ed by 0xff instead of data buffer for 8_8 mode
The registers for AD193X are defined as 0x800-0x810 for spi which uses
16_8 mode, for i2c to support AD1937, we will use 8_8 mode, only the low
byte of 0x800-0x810 is valid.  The patch will not destory other codecs,
but make soc cache interface more useful.

Signed-off-by: Barry Song <barry.song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-03-18 11:23:23 +00:00