This means "DMA Read returns" can bypass "MMIO Writes".
Violating the PCI specs in this case improves outbound DMA "flows"
and is currently not required by any drivers.
This is NOT a new behavior. Previous chipsets did this
already and I believe ZX1 PDC was already setting this
for hpux. I just want to further document the behavior.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
SERIAL_SGI_IOC4 and BLK_DEV_SGIIOC4 depend upon SGI_IOC4, and
SERIAL_SGI_IOC3 depends upon SGI_IOC3. Currently the definitions
are out of order in the config sequence.
Fix by including drivers/sn/Kconfig immediately after SGI_SN,
upon which SGI_IOC4 and SGI_IOC3 depend.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an oops in 2.6.16.X when loading the snd_powermac module. The
name of the requested module changed during the 2.6.16 development cycle
from i2c-keylargo to i2c-powermac.
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes several bugs in the gianfar driver, including a major one
where spinlocks were horribly broken:
* Split gianfar locks into two types: TX and RX
* Made it so gfar_start() now clears RHALT
* Fixed a bug where calling gfar_start_xmit() with interrupts off would
corrupt the interrupt state
* Fixed a bug where a frame could potentially arrive, and never be handled
(if no more frames arrived
* Fixed a bug where the rx_work_limit would never be observed by the rx
completion code
* Fixed a bug where the interrupt handlers were not actually protected by
their spinlocks
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the base address of the Realtek RTL8019AS chip on the Toshiba RBTX4938
board -- this should make the driver work at least when CONFIG_PCI is enabled.
Signed-off-by: Yuri Shpilevsky <yshpilevsky@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- fix mddev_lock() usage bugs in md_attr_show() and md_attr_store().
[they did not anticipate the possibility of getting a signal]
- remove mddev_lock_uninterruptible() [unused]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a test to detect the ICH7 based Core Duo SONY laptops (such as the SZ1)
as type3 models.
Signed-off-by: Arnaud MAZIN < arnaud.mazin@gmail.com>
Acked-by: Stelian Pop <stelian@poppies.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix for bug #6395:
Fail to resume on Tecra M2 with ADM1032 and Intel 82801DBM
The BIOS of the Tecra M2 doesn't like it when it has to reboot or resume
after the i2c-i801 driver has left the SMBus in PEC mode. The most simple
fix is to clear the PEC bit after after every transaction. That's what
this driver was doing up to 2.6.15 (inclusive).
Thanks to Daniele Gaffuri for the very good report.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On the MSI-K8T-NEO2 FIR ( Athlon-64, Socket 939 with VIA-K8T800- Chipset
and onboard Sound,... ) the BIOS lets you choose "DISABLED" or "AUTO" for
the On-Board Sound Device.
If you add another PCI-Sound-Card the BIOS disables the on-board device.
So far I have a Quirk, that does set the correspondent BIT in the
PCI-registers to enable the soundcard.
But how to ensure that the code is executed ONLY on excactly this kind of
boards (not any other with similar Chipset)?
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During module unloading, cdev_del() must be called to unmap cdev related
kobject references and other cleanups(such as inode->i_cdev being set to
NULL) which prevents the OOPS upon subsequent loading, usage and unloading
of modules(as seen in the mail thread
http://marc.theaimsgroup.com/?l=linux-kernel&m=114533640609018&w=2).
Also, remove unneeded test of gpio_base.
Signed-off-by: Thayumanavar Sachithanantham <thayumk@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
WARNING: drivers/video/pm2fb.o - Section mismatch: reference
to .init.data: from .text after 'pm2fb_set_par' (at offset 0xd5d)
WARNING: drivers/video/pm2fb.o - Section mismatch: reference
to .init.data: from .text after 'pm2fb_set_par' (at offset 0xd82)
They are caused because pm2fb_set_par() uses lowhsync and lowvsync which
are marked __devinitdata.
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In a short discussion with Benjamin Herrenschmidt he mentioned
that Marvell PHYs are powered down the same way as the other
ones we currently handle. Thus actually do that, hopefully
saving some power during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The room for the names in bcm43xx_priv_wx_args[] are IFNAMSIZ long and
IFNAMSIZ is defined as 16, so the names in bcm43xx_priv_wx_args should
be 15 characters (16 including the trailing \0). This patch fixes that
for the "set_shortpreambl", "get_shortpreambl", "set_swencryption", and
"get_swencryption" private calls. Patch is against 2.6.17-rc1.
Signed-off-by: Erik Mouw <erik@harddisk-recovery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up the bcm43xx sysfs code and makes it compliant
with the unwritten sysfs rules (at least I hope so).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "depends on" to make all bcm43xx driver options be listed
at the same level.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix printk format warnings:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:456: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:460: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:476: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:480: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:200: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:311: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:733: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbol firmware F3.91-71 has an additional word in the commsquality RID.
Extend the receiving buffer by one word to accomodate it.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2.6.17-rc1 changed the title for the entry CONFIG_NET_RADIO. I
personally disagree with this change and want it reverted. Patch for
2.6.17-rc1.
Rationale : WIRELESS_EXT is an invisible option. Therefore,
the only way for a user to enable it is via NET_RADIO. Some users need
to do that for out-of-tree drivers. Therefore it should be mentionned
in the title of the option.
Rationale2 : the option just below is called "Wireless
Extension API over RtNetlink". Some users may confuse this option for
the main "Wireless Extension" option. Therefore reverting this change
help disambiguate the relation between those two options.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send scan completion events to user space when a scan completes.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Airo firmware versions >= 5.30.17 send re-association events to the
driver that are currently unrecognized, causing spurious disassociation
events to be sent to user space. Loss of sync due to scan requests also
results in disassociation events sent to user space. This patch traps
those two events; suppressing sync-loss on scan, and sending the correct
association event on re-association notifications.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the needlessly global mthca_update_rate() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only check that RMPP version is not specified when MAD class does not
support RMPP. Just because a class is allowed to use RMPP doesn't
mean that rmpp_version needs to be set for the MAD agent to
register. Checking this was a recent change which was too pedantic.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a SCSI abort succeeds, then the aborted request should to be
removed from the list of pending requests. This fixes list corruption
after an abort occurs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix return code of fb_write():
If at least 1 byte was transferred to the device, return number of bytes,
otherwise:
- return -EFBIG - if file offset is past the maximum allowable offset or
size is greater than framebuffer length
- return -ENOSPC - if size is greater than framebuffer length - offset
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Marking radeon_pci_register() as __devinit clears up all section
mismatch warnings that are caused by radeon_pci_register() calling
various __devinit function. Is there some reason not to do this?
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text: from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x628)
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text: from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x6b5)
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text: from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x6bd)
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text:radeon_probe_screens from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x7d6)
WARNING: drivers/video/aty/radeonfb.o - Section mismatch: reference to .init.text:radeon_check_modes from .text.radeonfb_pci_register after 'radeonfb_pci_register' (at offset 0x7e5)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the following section mismatch:
WARNING: drivers/video/savage/savagefb.o - Section mismatch: reference to .init.data: from .text.savagefb_probe after 'savagefb_probe' (at offset 0x5e2)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From http://bugzilla.kernel.org/show_bug.cgi?id=6358
The alim15x3.c havn't been update for 3 years. Recently when we use this
"ULI M1573" south bridge chip found that can't mount CDROM(VCD) smoothly,
must waiting for a long time. After I check the "ULI M1573" south bridge
datasheet, I found the reason. The reason is the "ULI M1573" version in
the Linux is "0xC7" not "0xC4" anymore So I was modified the source than it
was successed.
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noted by Sergei Shtylylov <sshtylyov@ru.mvista.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the IDE device on ATI SB600
Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The wording of two messages in drivers/pnp/manager.c is incorrect. Fix that.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix all modpost section mismatch warnings in parport_pc:
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x230)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x283)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x3e6)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x400)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x463)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.text: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x488)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data:superios from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x54c)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_probe_port after 'parport_pc_probe_port' (at offset 0x56a)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x67)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x9f)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0xa7)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data:cards from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x132)
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference to .init.data: from .text.parport_pc_pci_probe after 'parport_pc_pci_probe' (at offset 0x142)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was looking into random driver code and found a suspicious looking
memcpy() in drivers/char/ipmi/ipmi_bt_sm.c on 2.6.17-rc1:
if ((size < 2) || (size > IPMI_MAX_MSG_LENGTH))
return -1;
...
memcpy(bt->write_data + 3, data + 1, size - 1);
where sizeof bt->write_data is IPMI_MAX_MSG_LENGTH. It looks like the
memcpy would overflow by 2 bytes if size == IPMI_MAX_MSG_LENGTH. A patch
attached to limit size to (IPMI_MAX_LENGTH - 2).
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
gcc complains about __devinit in the wrong location:
drivers/char/ipmi/ipmi_si_intf.c:2205: warning: '__section__' attribute does not apply to types
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are places in the kernel where we look up files in fd tables and
access the file structure without holding refereces to the file. So, we
need special care to avoid the race between looking up files in the fd
table and tearing down of the file in another CPU. Otherwise, one might
see a NULL f_dentry or such torn down version of the file. This patch
fixes those special places where such a race may happen.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Acked-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the bitmasks used when writing to the M41T00 registers.
The original code used a mask of 0x7f when writing to each register,
this is incorrect and probably the result of a copy-paste error. As a
result years from 1980 to 1999 will be read back as 2000 to 2019.
Signed-off-by: David Barksdale <amatus@ocgnet.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the EXPORT_SYMBOL_GPL of the static function cpufreq_parse_governor().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
The previous patch had bugs (locking and refcount).
This one could also be related to the latest DELL reports.
But they only slip into this if a user prog (e.g. powersave daemon does when
AC got (un) plugged due to a scheme change) echos something to
/sys/../cpufreq/scaling_governor
while the frequencies got limited by BIOS.
This one works:
Subject: Max freq stucks at low freq if reduced by _PPC and sysfs gov access
The problem is reproducable by(if machine is limiting freqs via BIOS):
- Unplugging AC -> max freq gets limited
- echo ${governor} >/sys/.../cpufreq/scaling_governor (policy->user_data.max
gets overridden with policy->max and will never come up again.)
This patch exchanged the cpufreq_set_policy call to __cpufreq_set_policy and
duplicated it's functionality but did not override user_data.max.
The same happens with overridding min/max values. If freqs are limited and
you override the min freq value, the max freq global value will also get
stuck to the limited freq, even if BIOS allows all freqs again.
Last scenario does only happen if BIOS does not reduce the frequency
to the lowest value (should never happen, just for correctness...)
drivers/cpufreq/cpufreq.c | 17 +++++++++++++++--
1 files changed, 15 insertions(+), 2 deletions(-)
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Patch from Richard Purdie
Move platform_scoop_config from the SharpSL scoop PCMCIA driver to
the SCOOP driver. This avoids build failures when PCMCIA is not built
or is modular (scoop.c itself cannot be modular).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Fix further issues in drivers/char/drm/via_irq.c
drivers/char/drm/drm_memory.c: possible cleanups
drm: deline a few large inlines in DRM code
drm: remove master setting from add/remove context
drm: drm_pci needs dma-mapping.h
[PATCH] drm: Fix issue reported by Coverity in drivers/char/drm/via_irq.c
Fix de-reference of 'dev_priv' before NULL check.
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
- #if 0 the following unused global function:
- drm_ioremap_nocache()
- make the following needlessly global functions static:
- agp_remap()
- drm_lookup_map()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix a crash when running hpacucli with multiple logical volumes on a cciss
controller. We were not properly initializing the disk->queue and causing
a fault.
Thanks to Hasso Tepper for reporting the problem. Thanks to Steve Cameron
for root causing the problem. Most of the patch just moves things around.
The fix is a one-liner.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Stephen Cameron <steve.cameron@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Limit USB_STORAGE_ISD200 to whatever BLK_DEV_IDE and USB_STORAGE
are set to (y, m) since isd200 calls ide_fix_driveid() in the
BLK_DEV_IDE code.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The at91_cf driver got out of sync with certain changes in the PCMCIA
layer, notably getting rid of some duplication of data ... causing the
version merged to kernel.org to fail compiling.
This patch gives the at91_cf platform device a new iomem resource, using
it so this new pcmcia scheme works. It also cleans up some whitepsace
bugs that have accumulated over time (mostly too-long lines).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original patch by Benjamin Herrenschmidt after debugging by Brian Hinz.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Brian Hinz <bphinz@hotmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (170 commits)
commit 3d9dd7564d
Author: Zach Brown <zach.brown@oracle.com>
Date: Fri Apr 14 16:04:18 2006 -0700
[PATCH] ip_output: account for fraggap when checking to add trailer_len
During other work I noticed that ip_append_data() seemed to be forgetting to
include the frag gap in its calculation of a fragment that consumes the rest of
the payload. Herbert confirmed that this was a bug that snuck in during a
previous rework.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 08d099974a
Author: Linus Walleij <triad@df.lth.se>
Date: Fri Apr 14 16:03:33 2006 -0700
[IRDA]: smsc-ircc2, smcinit support for ALi ISA bridges
...
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (679 commits)
commit 7676f83aeb
Author: James Bottomley <James.Bottomley@steeleye.com>
Date: Fri Apr 14 09:47:59 2006 -0500
[SCSI] scsi_transport_sas: don't scan a non-existent end device
Any end device that can't support any of the scanning protocols
shouldn't be scanned, so set its id to -1 to prevent
scsi_scan_target() being called for it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
commit 3c0c25b97c
Author: Moore, Eric <Eric.Moore@lsil.com>
Date: Thu Apr 13 16:08:17 2006 -0600
[SCSI] mptfusion - fix panic in mptsas_slave_configure
Driver panic when RAID logical volume was present when driver
loaded, or when a RAID logical volume was created on the fly.
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6: (78 commits)
commit e97b81ddbb
Author: Mark M. Hoffman <mhoffman@lightlink.com>
Date: Thu Mar 23 16:50:25 2006 +0100
[PATCH] i2c-parport: Make type parameter mandatory
This patch forces the user to specify what type of adapter is present when
loading i2c-parport or i2c-parport-light. If none is specified, the driver
init simply fails - instead of assuming adapter type 0.
This alleviates the sometimes lengthy boot time delays which can be caused
by accidentally building one of these into a kernel along with several i2c
slave drivers that have lengthy probe routines (e.g. hwmon drivers).
Kconfig and documentation updated accordingly.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (169 commits)
commit 78a596b449
Author: Adrian Bunk <bunk@stusta.de>
Date: Fri Mar 31 01:38:12 2006 -0800
[PATCH] remove kernel/power/pm.c:pm_unregister()
Since the last user is removed in -mm, we can now remove this long deprecated
function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 21440d3133
Author: David Brownell <david-b@pacbell.net>
Date: Sat Apr 1 10:21:52 2006 -0800
[PATCH] dma doc updates
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (158 commits)
commit 4f705ae3e9
Author: Bjorn Helgaas <bjorn.helgaas@hp.com>
Date: Mon Apr 3 17:09:22 2006 -0700
[PATCH] DMI: move dmi_scan.c from arch/i386 to drivers/firmware/
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.
This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes. All three
architectures already set CONFIG_DMI in their top-level Kconfig files.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
...
From: Linus Walleij <triad@df.lth.se>
This patch enables support for ALi ISA bridges when we run the smcinit
code. It is needed to properly configure some Toshiba laptops.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the STIR421x case, when the firmware upload fails, we need to
unregister_netdev. Otherwise we hit a BUG on free_netdev(), if sysfs
is enabled.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any end device that can't support any of the scanning protocols
shouldn't be scanned, so set its id to -1 to prevent
scsi_scan_target() being called for it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Asus A6VA notebook was reported to need a PCI quirk to unhide
the SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The init function for the RPA PCI Hotplug driver returns -ENODEV in the
case that no hotplug-capable slots are detected in the system. This is
bad, since hot-capable slots can be added after boot to a purely virtual
POWER partition. This is also bad because DLPAR I/O operations depend
on the rpaphp module.
Change the rpaphp init module to return success for the case of
partitions that own no hotplug-capable slots at boot. Such slots can be
dynamically added after boot.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The naming of the constant defined for PCI ID 1022:7450 does not seem
to match the information at http://pciids.sourceforge.net/:
http://pci-ids.ucw.cz/iii/?i=1022
There 1022:7450 is listed as "AMD-8131 PCI-X Bridge" while 1022:7451
is listed as "AMD-8131 PCI-X IOAPIC". Yet, the current definition for
0x7450 is PCI_DEVICE_ID_AMD_8131_APIC. It seems to me like that name
should map to 0x7451, while a name like PCI_DEVICE_ID_AMD_8131_BRIDGE
should map to 0x7450.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.
This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes. All three
architectures already set CONFIG_DMI in their top-level Kconfig files.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Print more diagnostic info to help identify the source of power management
suspend failures.
Example:
usb_hcd_pci_suspend(): pci_set_power_state+0x0/0x1af() returns -22
pci_device_suspend(): usb_hcd_pci_suspend+0x0/0x11b() returns -22
suspend_device(): pci_device_suspend+0x0/0x34() returns -22
Work-in-progress. It needs lots more suspend_report_result() calls sprinkled
everywhere.
Cc: Patrick Mochel <mochel@digitalimplant.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The manual driver <-> device binding attribute in sysfs doesn't return
the correct value on failure or success of driver_probe_device.
driver_probe_device returns 1 on success (the driver accepted the
device) or 0 on probe failure (when the driver didn't accept the
device but no real error occured). However, the attribute can't just
return 0 or 1, it must return the number of bytes consumed from buf
or an error value. Returning 0 indicates to userspace that nothing
was written (even though the kernel has tried to do the bind/probe and
failed). Returning 1 indicates that only one character was accepted in
which case userspace will re-try the write with a partial string.
A more correct version of driver_bind would return count (to indicate
the entire string was consumed) when driver_probe_device returns 1
and -ENODEV when driver_probe_device returns 0. This patch makes that
change.
Signed-off-by: Ryan Wilson <hap9@epoch.ncsc.mil>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tries to fix an issue in drivers/base/class.c, please
review and apply if correct.
Patch Description:
"parent_class" is checked for NULL already, so removed the unnecessary
check.
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as667) changes the __device_release_driver() routine to
prevent it from crashing when it runs across a device not on any bus.
This seems logical, inasmuch as the corresponding bus_add_device()
routine has an explicit check allowing it to accept such devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It works like this:
Open the file
Read all the contents.
Call poll requesting POLLERR or POLLPRI (so select/exceptfds works)
When poll returns,
close the file and go to top of loop.
or lseek to start of file and go back to the 'read'.
Events are signaled by an object manager calling
sysfs_notify(kobj, dir, attr);
If the dir is non-NULL, it is used to find a subdirectory which
contains the attribute (presumably created by sysfs_create_group).
This has a cost of one int per attribute, one wait_queuehead per kobject,
one int per open file.
The name "sysfs_notify" may be confused with the inotify
functionality. Maybe it would be nice to support inotify for sysfs
attributes as well?
This patch also uses sysfs_notify to allow /sys/block/md*/md/sync_action
to be pollable
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch forces the user to specify what type of adapter is present when
loading i2c-parport or i2c-parport-light. If none is specified, the driver
init simply fails - instead of assuming adapter type 0.
This alleviates the sometimes lengthy boot time delays which can be caused
by accidentally building one of these into a kernel along with several i2c
slave drivers that have lengthy probe routines (e.g. hwmon drivers).
Kconfig and documentation updated accordingly.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes an init-time kernel log message.
http://marc.theaimsgroup.com/?l=linux-kernel&m=114232987208628&w=3
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the w83792d driver keep quiet when misdetecting a chip. This can
happen, and the user doesn't need to know.
Also renumber the messages, and add one, for consistency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The m41t00 i2c/rtc driver currently uses a tasklet to schedule
interrupt-level writes to the rtc. This patch causes the driver
to use a workqueue instead.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A tasklet is not suitable for what the ds1374 driver does: neither sleeping
nor mutex operations are allowed in tasklets, and ds1374_set_tlet may do
both.
We can use a workqueue instead, where both sleeping and mutex operations
are allowed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prevents an Oops if booted with "console=ttyUSB0" but without a
USB-serial dongle, and plugged one in afterwards.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for a clone of Nokia DKU-5 cable made by
Ours Technology Inc for Nokia phones with PopPort (Nokia 3100 and others).
The cable uses PL2303 USB-to-serial converter from Prolific Technology Inc.
Signed-off-by: Tomasz Kazmierczak <tomek.fizyk@op.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get the "usb-bus" clock and ensure it is enabled
when the OHCI core is in use.
It seems that a few bootloaders do not enable the
UPLL at startup, which stops the OHCI core having
a 48MHz bus clock. The improvements to the clock
framework for the s3c24xx now allow the USB PLL
to be started and stopped when being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When not using this patch, the kernel will continuously return "input irq
status -32 received", while making the keyboard unusable. This can be
easely resolved using HID_QUIRK_NOGET. Vendor-ID and Device-ID should be
applied to hid-core.c, and making an entry to make use of it.
Signed-off-by: Jeffrey Vandenbroucke <jeffrey@wirehead.be>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone recently posted a bug report where it turned out that uhci-hcd
was disagreeing with the UHCI controller over whether or not a port was
suspended: The driver thought it wasn't and the hardware thought it was.
This patch (as665) fixes the problem and simplifies the driver by
removing the internal state-tracking completely. Now the driver just
asks the hardware whether a port is suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the ASIX code is supporting more than just the AX88172 devices,
make the utility function names more generic: ax8817x_func -> asix_func.
Functions that are chip specific now indicate as such: ax88772_func.
Additionally, pull some common routines used in initialization and such
into simple functions to reduce the verbosity of certain functions such
as
the bind() routines and to make the error handling consistent across the
board.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move common definitions for NET2280 to <linux/usb/net2280.h>, so that I can
use them in prism54usb (it is not merged yet, but I plan to do it soon).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Be sure to record the peripheral's ep0 maxpacket size BEFORE using
that to initialize the (high speed) device qualifier; that helps a
lot with USBCV testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously, scatterlist tests didn't write patterned data. Given how many
corner cases are addresed by them, this was a significant gap in Linux-USB
test coverage. Moreover, when peripherals checked for correct data patterns,
false error reports would drown out the true ones.
This adds the pattern on the way OUT from the host, so scatterlist tests can
now be used to uncover bugs like host TX or peripheral RX paths failing for
back-to-back short packets. It's easy enough to get an error there with at
least one of the {DMA,PIO}{RX,TX} code paths, or run into hardware races
that need to be defended against.
Note this patch doesn't add checking for correct data patterns on the way
IN from peripherals, just a FIXME for later.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AT91: the two USB drivers (OHCI, UDC) got out of sync with various
usbcore and driver model PM updates; fix.
Also minor fixes to ohci: whitespace/style, MODULE_ALIAS so coldplug works
using /sys/.../modalias, and turn off _both_ clocks during suspend.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fill OUT buffers with 0x55 before RX, so that controller driver
bugs that mangle data can be more readily detected during testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This catches up to a change in the Kconfig support for highspeed modes;
the change predated 2.6.10, and anyone using gadgetfs on a highspeed
device would see the kernel wrongly reject the alternate descriptors.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a "avoid proprietary protocols" warnoff, identifying several
of the known deficiencies in Microsoft's excuse-for-specification, and
fixes some whitespace bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some patch broke short-OUT packet handling for net2280, making it report
illegal status values. This updates the status code so it's correct.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I submitted the wrong version of the patch teaching about the driver
for Mentor's Highspeed Dual Role Controller (HDRC), whoops! This
uses the right name for that driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB OTG devices are not required to support external hubs. This adds a
configuration option to disable that support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch fix leak of memory allocated to intr if allocation of
sc->urb_int fails.
Found by the Coverity checker.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- increase ack timeout for slow system (geode 233MHz where HZ=100)
- reset the cmv ack flag when rebooting
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- improve debug trace in order to make easy to solve user problems.
- indent some code
- increase version number
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached is a patch that fixes nasty bug, which i am afraid was there
for a long time. It was spotted by Andre Draszik <kernel@andred.net>.
From: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for DTF 521, Intuos3 12x12, and 12x19;
fixes minor data report bugs.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap pointed out that there now is a module_param_array_named
macro available. This patch (as666) updates g_file_storage to make use of
it. It also adds a comment listing the specifications documents used in
the design of the driver's SCSI operation (at Pat LaVarre's request).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A new single driver for various USB touchscreen devices. It currently
supports:
- eGalax TouchKit
- PanJit TouchSet
- 3M/Microtouch
- ITM Touchscreens
Support for the diffent devices can be enabled/disable when CONFIG_EMBEDDED
is set.
Sizes for comparision:
text data bss dec hex filename
2942 724 4 3670 e56 touchkitusb.ko
2647 660 0 3307 ceb mtouchusb.ko
2448 628 0 3076 c04 itmtouch.ko
4145 1012 12 5169 1431 usbtouchscreen.ko
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds proper prototypes in a header file for some global
functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a header file with proper prototypes for two functions
in drivers/usb/host/pci-quirks.c.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbserial's port semaphore used to synchronize serial_open()
and serial_close() are strict mutexes, convert them to the mutex
implementation.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as664) adds a comment to file_storage.c, noting that the
driver is slightly non-portable because it assumes that a buffer
allocated for a bulk-in endpoint will also be useable for a bulk-out
endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm told that some UDC hardware may work better if it knows that
receiving a short packet should always cause an error. Accordingly,
this patch (as663) sets the short_not_ok flag for bulk-out transfers in
g_file_storage. Oddly enough, there are no circumstances where that
driver can legally receive a shorter-than-expected bulk-out packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the Eclo COM to 1-Wire USB adapter
<http://www.eclo.pt/products_ibutton_adapters_usb01_en.asp> to the
ftdi_sio driver's device ID table. Details were provided by Martin
Grill on the ftdi-sio-usb-devel mailing list and I (Ian Abbott)
confirmed it matched the INF file in the Eclo's Windows driver package.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix compile errors due to functions not being
defined static
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch to gadgets/net2280.[ch] which adds support for the
net2282 controller. The original code was kindly provided by PLX
Technology, I just merged it with the current net2280 driver in the
kernel. Tested on 2.6.15.6, but only with 2282. I did the merge, so
that the behaviour for the 2280 is unaffected (except for short delays
for extra checks).
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for net2282 in net2280 driver.
Driver panic when RAID logical volume was present when driver
loaded, or when a RAID logical volume was created on the fly.
This issue was created in due to recent scsi_transport_sas change,
when sas_read_port_mode_page was added into the mptsas drivers
slave_config entry point.
This new API expects that all sdev's to be assocated to an rphy, however
that is not the case for logical volumes, as they are created using
scsi_add_device, instead of sas_rphy_add().
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
By calling send_sig do_SAK is recursively taking the
tasklist_lock, which is silly.
In addition I just audited the kernel and this was the only
place where tasklist_lock is taken inside of task_lock.
So this one line change is a general worthwhile cleanup and
it increases our options on how to fix the ptrace_attach races.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Equivalent of the same patch for the 3w-xxxx driver.
Signed-off-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_kill_request() completes requests via normal SCSI completion path
which decrements busy counts; however, requests which get passed to
scsi_kill_request() aren't holding busy counts and scsi_kill_request()
don't increment them before invoking completion path resulting in
incorrect busy counts. Bump up busy counts before invoking completion
path.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As previously reported via Michael Reed, the FC transport took a hit
in 2.6.15 (perhaps a little earlier) when we solved a recursion error.
There are 2 deadlocks occurring:
- With scan and the delete items sharing the same workq, flushing the
workq for the delete code was getting it stalled behind a very long
running scan code path.
- There's a deadlock where scsi_remove_target() has to sit behind
scsi_scan_target() due to contention over the scan_lock().
This patch resolves the 1st deadlock and significantly reduces the
odds of the second. So far, we have only replicated the 2nd deadlock
on a highly-parallel SMP system. More on the 2nd deadlock in a following
email.
This patch reworks the transport to:
- Only use the scsi host workq for scanning
- Use 2 other workq's internally. One for deletions, the other for
scheduled deletions. Originally, we tried this with a single workq,
but the occassional flushes of the scheduled queues was hitting the
second deadlock with a slightly higher frequency. In the future, we'll
look at the LLDD's and the transport to see if we can get rid of this
extra overhead.
- When moving to the other workq's we tightened up some object states
and some lock handling.
- Properly syncs adds/deletes
- minor code cleanups
- directly reference fc_host_attrs, rather than through attribute
macros
- flush the right workq on delayed work cancel failures.
Large kudos to Michael Reed who has been working this issue for the last
month.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a target is added aic79xx tries to be overly clever: it changes
the command on the fly to TEST UNIT READY and tries to requeue the
original command. Sadly this breaks SCSI compability and of course
the midlayer is getting a bit confused by it.
So we're just removing that bit of code and let the midlayer deal with
it. It's clever enough by now. And the driver code is getting simpler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's no longer needed after the convrsion to use the linux srp.h file.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As James B. correctly noted, ahd_reset_channel() in
ahd_linux_bus_reset() should be protected by ahd_lock(). However, the
main reason for not doing so was a deadlock with the interesting
polling mechanism to detect the end a bus reset.
This patch replaces the polling mechanism with a saner signalling via
flags; it also gives us the benefit of detecting any multiple calls to
ahd_reset_channel().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Ingo Flaschberger <if@xip.at>
To support the RA4100 array from Compaq.
This patch now correctly handles SCSI_UNKNOWN types with regard to
BLIST_REPORTLUNS2 (allow it) and cdb[1] LUN inclusion (don't).
It also allows a BLIST_MAX_512 flag to restrict the maximum transfer
length to 512 blocks (apparently this is an RA4100 problem).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When spinlock debugging is turned on, a struct completion grows beyond the
size allowed for the scsi_pointer. So move the struct completion back onto
the stack. The additional memory barriers are to keep us from completing
a random piece of kernel stack if the command happens to complete after
the error handling has finished.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Encapsulate some more of the device reset processing in
preparation for SATA support.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove some unused printk macros, make some more robust, and
convert some to use standard printk macros when possible.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify the dumping of the command status area by
removing some device specific information that has proven
to not be worthwhile.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixup a check used by the ipr driver to determine if a given
device is a SCSI disk. Due to the addition of support for
attaching SATA devices, this check needs to be more robust.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Instead of NULLing the resource entry pointer when a disk
goes away to prevent any new commands being sent to it,
set the adapter resource handle to an invalid value so
new ops getting sent to it will fail with a selection timeout
response. This patch is needed for future SATA patches.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
when the sg driver is unable to setup direct IO, free that scatter
gather list prior to falling back to indirect IO
Further to this thread started by Bryan Holty:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114306885116728&w=2
Here is the reworked patch again. This time it has been
tested with a program provided by Bryan.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch enables clustering and sets max_sectors to 0xffff to enable
reading and writing of large blocks with tapes (and large transfers with
sg). This change is needed after the sg and st drivers started using
chained bios through scsi_request_async() in 2.6.16.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use wait_for_completion_timeout() instead of using a timer (as
Christoph Hellwig did for aic7xxx).
That lets me eliminate the sym_eh_wait structure; the struct completion,
the old_done pointer and the to_do flag can be folded into the sym_ucmd
(which overrides the scsi_pointer in scsi_cmnd).
The sym_eh_done() function becomes much simpler as the timeout handling
is done in sym_eh_handler() directly.
The host_lock can be unlocked earlier, and I cache the host in
a local variable to make accesses to it quicker.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The PDC code can set the bus mode, but we were ignoring that setting.
Also move the code that determines bus mode into its own function.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Now sym2 is using spi_print_msg, we don't need to have our own messages
for IGNORE WIDE RESIDUE and MODIFY DATA POINTER, so provide the option
of passing NULL for the label.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Undef SYM_OPT_HANDLE_DEVICE_QUEUEING.
Call sym_put_start_queue instead of sym_start_next_ccbs.
Turn asserts into checks that we can send the command to the adapter,
and return busy from queuecommand if we can't.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch below is one out of a large series to mark kernel data const when
possible, goal is to use .rodata and avoid false sharing
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- to_do was never set to SYM_EH_DO_COMPLETE, so remove that code
- move the spinlocks inside the common error handler code path
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We had our own code (pci_get_base_address()) to get the bus address of
a BAR. We can get this using pcibios_resource_to_bus() instead.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Most of the Kconfig options for switching between IO Port and MMIO
operations use the opposite sense from sym2. Really, this option
should be set at a chipset level rather than per-driver.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix puts so that release functions will be called.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Fix module param
Update driver version.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
On 64 bit machines, when a 32 bit application tries to acquire the AIF,
they will always get and EFAULT error response from the driver.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Add max_channel and max_id sysfs parameters.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Since the helper thread for the driver can be killed unceremoniously by
an application, we detect the loss of the helper and restart it.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Remove superfluous code, optimize code, harden code, cast code, correct
some text, use msleep instead of schedule_timeout_interruptible. No
bugs.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
If there are no aacraid controllers, we do not create the raid
controller chrdev, thus when the driver is unloaded it performs a
superfluous deregistration.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
The max_channel field is set one too large.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Some of the error return paths during initialization resulted in a zero
report to caller
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Plug and play actions resulting from event sequences shall time out if
they take longer than 30 seconds to complete.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
The loss of the ownership flags, despite their flaws, in the scsi
command were sorely missed and are reinstated more accurately in the
aacraid driver to track commands and permit us to properly handle error
recovery actions.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Clean up the remaining scsi id access methods, drop ID_LUN_TO_CONTAINER
macro.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a window where we can be re-enabling an adapter, but
still allow SCSI commands to be sent to the target. This fix
sets our window (request_limit) to -1 as soon as we know the
adapter is being reenabled, and closes a very teeny tiny
window where we could set the window back to 1 before we
grab a lock.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Doug found a bug where if scsi_execute_async fails, we are leaking
sg resources. scsi_do_req never failed so we did not have to handle
that case before.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently have two implementations of this obsolete ioctl, one in
the block layer and one in the scsi code. Both of them have drawbacks.
This patch kills the scsi layer version after updating the block version
with the missing bits:
- argument checking
- use scatterlist I/O
- set number of retries based on the submitted command
This is the last user of non-S/G I/O except for the gdth driver, so
getting this in ASAP and through the scsi tree would be nie to kill
the non-S/G I/O path. Jens, what do you think about adding a check
for non-S/G I/O in the midlayer?
Thanks to Or Gerlitz for testing this patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Use pci_set_consistent_dma_mask in ixgb driver
[PATCH] sky2: bad memory reference on dual port cards
[PATCH] mv643xx_eth: Fix tx_timeout to only conditionally wake tx queue
[PATCH] mv643xx_eth: Always free completed tx descs on tx interrupt
[PATCH] net drivers: fix section attributes for gcc
[PATCH] remove drivers/net/hydra.h
[PATCH] drivers/net/via-rhine.c: make a function static
[netdrvr b44] trim trailing whitespace
[PATCH] b44: increase version to 1.00
[PATCH] b44: disable default tx pause
[PATCH] via-rhine: execute bounce buffers code on Rhine-I only
[PATCH] network: axnet_cs.c: add missing 'PRIV' in ei_rx_overrun
[PATCH] dlink pci cards using wrong driver
The ixgb driver is using pci_alloc_consistent, thus is should also use
pci_set_consistent_dma_mask. This allows the driver to work on SGI
systems.
In case of an error during probing it should also disable the device again.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sky2 driver will oops referencing bad memory if used on
a dual port card. The problem is accessing past end of
MIB counter space.
Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After resetting the hardware on a tx_timeout, call netif_wake_queue()
only if we have free tx descriptors.
Also, attempt to recover if mv643xx_eth_start_xmit() is called when
there are fewer free tx descriptors than expected.
The BUG_ON() call we are replacing was hit on a tx_timeout that
called netif_wake_queue(), indirectly via netif_device_attach(),
even though we did not have enough free tx descriptors.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the tx interrupt handler to free completed tx descriptors even
when NAPI is enabled. Otherwise, the tx queue would fill up resulting
in poor performance and "NETDEV WATCHDOG: <iface>: transmit timed out"
messages.
Signed-off-by: Brent Cook <bcook@bpointsys.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If CONFIG_HOTPLUG=n, gcc doesn't like some __initdata to be const (rodata)
and other __initdata not const, so make the non-const __initdata const.
gcc errors:
drivers/net/bnx2.c:66: error: version causes a section type conflict
drivers/net/starfire.c:338: error: version causes a section type conflict
drivers/net/typhoon.c:137: error: version causes a section type conflict
drivers/net/natsemi.c:241: error: version causes a section type conflict
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove drivers/net/hydra.h which is both unused and covered by a 4 clause
BSD licence (not by the UCB).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-By: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently it crashes when trying to dump the registers. This is an obvious
one-liner fix I suppose.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Disable default tx pause frame support.
The b44 controller has a bug that generates excessive tx pause
frames.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the problem of some Dlink cards picking the wrong
driver. It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver allocates SRQ WQEs size with a power of 2 size both for
Tavor and for memfree. For Tavor, however, the hardware only requires
the WQE size to be a multiple of 16, not a power of 2, and the max
number of scatter-gather allowed is reported accordingly by the
firmware (and this is the value currently returned by
ib_query_device() and ibv_query_device()).
If the max number of scatter/gather entries reported by the FW is used
when creating an SRQ, the creation will fail for Tavor, since the
required WQE size will be increased to the next power of 2, which
turns out to be larger than the device permitted max WQE size (which
is not a power of 2).
This patch reduces the reported SRQ max wqe size so that it can be used
successfully in creating an SRQ on Tavor HCAs.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The pen down IRQ will toggle during each X,Y,Z measurement cycle.
Even though the IRQ is disabled it will be latched and delivered
when after enable_irq. Thus in the IRQ handler we must avoid
starting a new measurement cycle when such an "unwanted" IRQ happens.
Add a get_pendown_state platform function, which will probably
determine this by reading the current GPIO level of the pen IRQ pin.
Move the IRQ reenabling from the SPI RX function to the timer. After
the last power down message the pen IRQ pin is still active for a
while and get_pendown_state would report incorrectly a pen down state.
When suspending we should check the ts->pending flag instead of
ts->pendown, since the timer can be pending regardless of ts->pendown.
Also if ts->pending is set we can be sure that the timer is running,
so no need to rearm it. Similarly if ts->pending is not set we can
be sure that the IRQ is enabled (and the timer is not).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Add disable attribute to support device locking mode where
unintentional touch event shouldn't wake up the system;
- Update comments;
- Add missing spin_lock_init;
- Do device resume with the lock held;
- Do cleanup calls / free memory in the reverse order of initialization.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes a polling loop had a hard time changing state without
pre-emption enabled. Use msleep instead, it's better anyway.
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some touchscreens seem to oscillate heavily for a while after touching
the screen. Implement support for sampling the screen until we get two
consecutive values that are close enough.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Submit a seperate request for powering down the ADC in ads7846,
doing it after the last read request. Otherwise some of the read
values are incorrect.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It's handy for userspace diagnostics to see the pen down status, to
see whether the touchscreen is "stuck" (shortcircuited).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Coverity found some static overruns in isdn_ppp.c (bug id #519) At several
places slot is compared <0 and > ISDN_MAX_CHANNELS and then used to index
ippp_table[ISDN_MAX_CHANNELS] A value of slot = ISDN_MAX_CHANNELS would run
over the end of the array.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The in-kernel Sangoma drivers are both not compiling and marked as BROKEN
since at least kernel 2.6.0.
Sangoma offers out-of-tree drivers, and David Mandelstam told me Sangoma
does no longer maintain the in-kernel drivers and prefers to provide them
as a separate installation package.
This patch therefore removes these drivers.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: fix typo in change count initialization
kconfig: recenter menuconfig
kconfig: revert conf behaviour change
kconfig: fix default value for choice input
kbuild: fix NULL dereference in scripts/mod/modpost.c
kbuild: fix mode of checkstack.pl and other files.
kbuild: rebuild initramfs if content of initramfs changes
kbuild: properly pass options to hostcc when doing make O=..
kbuild: modules_install for external modules must not remove existing modules
kbuild: fix make dir/
ver_linux: don't print reiser4progs version if none found
kbuild: mips: fix sed regexp to generate asm-offset.h
kbuild: fix building single targets with make O=.. single-target
kbuild: use relative path to -I
kbuild: fix unneeded rebuilds in drivers/net/chelsio after moving source tree
kbuild: fix unneeded rebuilds in drivers/media/video after moving source tree
kbuild: fix garbled text in modules.txt
Since the arrays are declared as in_urbs[N_IN_URB]
and out_urbs[N_OUT_URB], both for loops go one
over the end of the array. This fixes coverity id #555.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-Off-By: Linus Torvalds <torvalds@osdl.org>
Since the visual STATIC_PSEUDOCOLOR has a read-only colormap, use logos
with 16 colors only since these logos use the console palette. This has a
higher likelihood that the logo will display correctly.
Signed-of-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bugzilla Bug 6299:
A pixel size of 8 bits produces wrong logo colors in x86_64.
The driver has 2 methods for setting the color map, using the protected
mode interface provided by the video BIOS and directly writing to the VGA
registers. The former is not supported in x86_64 and the latter is enabled
only in i386.
Fix by enabling the latter method in x86_64 only if supported by the BIOS.
If both methods are unsupported, change the visual of vesafb to
STATIC_PSEUDOCOLOR.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Heaps of build errors - disable it to keep sparc32 allmodconfig happy.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an obvious of-by-one error spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CRC_CCITT is an internal helper function that should be select'ed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
