With the Simple Pairing support, the authentication requirements are
an explicit setting during the bonding process. Track and enforce the
requirements and allow higher layers like L2CAP and RFCOMM to increase
them if needed.
This patch introduces a new IOCTL that allows to query the current
authentication requirements. It is also possible to detect Simple
Pairing support in the kernel this way.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth technology introduces new features on a regular basis
and for some of them it is important that the hardware on both sides
support them. For features like Simple Pairing it is important that
the host stacks on both sides have switched this feature on. To make
valid decisions, a config stage during ACL link establishment has been
introduced that retrieves remote features and if needed also the remote
extended features (known as remote host features) before signalling
this link as connected.
This change introduces full reference counting of incoming and outgoing
ACL links and the Bluetooth core will disconnect both if no owner of it
is present. To better handle interoperability during the pairing phase
the disconnect timeout for incoming connections has been increased to
10 seconds. This is five times more than for outgoing connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Simple Pairing process can only be used if both sides have the
support enabled in the host stack. The current Bluetooth specification
has three ways to detect this support.
If an Extended Inquiry Result has been sent during inquiry then it
is safe to assume that Simple Pairing is enabled. It is not allowed
to enable Extended Inquiry without Simple Pairing. During the remote
name request phase a notification with the remote host supported
features will be sent to indicate Simple Pairing support. Also the
second page of the remote extended features can indicate support for
Simple Pairing.
For all three cases the value of remote Simple Pairing mode is stored
in the inquiry cache for later use.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Simple Pairing feature is optional and needs to be enabled by the
host stack first. The Linux kernel relies on the Bluetooth daemon to
either enable or disable it, but at any time it needs to know the
current state of the Simple Pairing mode. So track any changes made
by external entities and store the current mode in the HCI device
structure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the Simple Pairing process the HCI disconnect timer must be
disabled. The way to do this is by holding a reference count of the
HCI connection. The Simple Pairing process on both sides starts with
an IO Capabilities Request and ends with Simple Pairing Complete.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth specification supports the default link policy settings
on a per host controller basis. For every new connection the link
manager would then use these settings. It is better to use this instead
of bothering the controller on every connection setup to overwrite the
default settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The connection packet type can be changed after the connection has been
established and thus needs to be properly tracked to ensure that the
host stack has always correct and valid information about it.
On incoming connections the Bluetooth core switches the supported packet
types to the configured list for this controller. However the usefulness
of this feature has been questioned a lot. The general consent is that
every Bluetooth host stack should enable as many packet types as the
hardware actually supports and leave the decision to the link manager
software running on the Bluetooth chip.
When running on Bluetooth 2.0 or later hardware, don't change the packet
type for incoming connections anymore. This hardware likely supports
Enhanced Data Rate and thus leave it completely up to the link manager
to pick the best packet type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth specification allows to enable or disable the encryption
of an ACL link at any time by either the peer or the remote device. If
a L2CAP or RFCOMM connection requested an encrypted link, they will now
disconnect that link if the encryption gets disabled. Higher protocols
that don't care about encryption (like SDP) are not affected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Recent tests with various Bluetooth headsets have shown that some of
them don't enforce authentication and encryption when connecting. All
of them leave it up to the host stack to enforce it. Non of them should
allow unencrypted connections, but that is how it is. So in case the
link mode settings require authentication and/or encryption it will now
also be enforced on outgoing RFCOMM connections. Previously this was
only done for incoming connections.
This support has a small drawback from a protocol level point of view
since the host stack can't really tell with 100% certainty if a remote
side is already authenticated or not. So if both sides are configured
to enforce authentication it will be requested twice. Most Bluetooth
chips are caching this information and thus no extra authentication
procedure has to be triggered over-the-air, but it can happen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pass double tcf_proto pointers to tcf_destroy_chain() to make it
clear the start of the filter list for more consistency.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[ Based upon original report and patch by Karsten Keil. Karsten
has verified that this fixes the TAHI test case "ICMPv6 test
v6LC.5.1.2 Part F". -DaveM ]
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix three ct_extend/NAT extension related races:
- When cleaning up the extension area and removing it from the bysource hash,
the nat->ct pointer must not be set to NULL since it may still be used in
a RCU read side
- When replacing a NAT extension area in the bysource hash, the nat->ct
pointer must be assigned before performing the replacement
- When reallocating extension storage in ct_extend, the old memory must
not be freed immediately since it may still be used by a RCU read side
Possibly fixes https://bugzilla.redhat.com/show_bug.cgi?id=449315
and/or http://bugzilla.kernel.org/show_bug.cgi?id=10875
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts two changesets, ec3c0982a2
("[TCP]: TCP_DEFER_ACCEPT updates - process as established") and
the follow-on bug fix 9ae27e0adb
("tcp: Fix slab corruption with ipv6 and tcp6fuzz").
This change causes several problems, first reported by Ingo Molnar
as a distcc-over-loopback regression where connections were getting
stuck.
Ilpo Järvinen first spotted the locking problems. The new function
added by this code, tcp_defer_accept_check(), only has the
child socket locked, yet it is modifying state of the parent
listening socket.
Fixing that is non-trivial at best, because we can't simply just grab
the parent listening socket lock at this point, because it would
create an ABBA deadlock. The normal ordering is parent listening
socket --> child socket, but this code path would require the
reverse lock ordering.
Next is a problem noticed by Vitaliy Gusev, he noted:
----------------------------------------
>--- a/net/ipv4/tcp_timer.c
>+++ b/net/ipv4/tcp_timer.c
>@@ -481,6 +481,11 @@ static void tcp_keepalive_timer (unsigned long data)
> goto death;
> }
>
>+ if (tp->defer_tcp_accept.request && sk->sk_state == TCP_ESTABLISHED) {
>+ tcp_send_active_reset(sk, GFP_ATOMIC);
>+ goto death;
Here socket sk is not attached to listening socket's request queue. tcp_done()
will not call inet_csk_destroy_sock() (and tcp_v4_destroy_sock() which should
release this sk) as socket is not DEAD. Therefore socket sk will be lost for
freeing.
----------------------------------------
Finally, Alexey Kuznetsov argues that there might not even be any
real value or advantage to these new semantics even if we fix all
of the bugs:
----------------------------------------
Hiding from accept() sockets with only out-of-order data only
is the only thing which is impossible with old approach. Is this really
so valuable? My opinion: no, this is nothing but a new loophole
to consume memory without control.
----------------------------------------
So revert this thing for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun noticed that we may call reqsk_free on request sock objects where
the opt fields may not be initialized, fix it by introducing inet_reqsk_alloc
where we initialize ->opt to NULL and set ->pktopts to NULL in
inet6_reqsk_alloc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- The tcp_unhash() method in /include/net/tcp.h is no more needed, as the
unhash method in tcp_prot structure is now inet_unhash (instead of
tcp_unhash in the
past); see tcp_prot structure in net/ipv4/tcp_ipv4.c.
- So, this patch removes tcp_unhash() declaration from include/net/tcp.h
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e9df2e8fd8 ("[IPV6]: Use
appropriate sock tclass setting for routing lookup.") also changed the
way that ECN capable transports mark this capability in IPv6. As a
result, SCTP was not marking ECN capablity because the traffic class
was never set. This patch brings back the markings for IPv6 traffic.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are trying to fast retransmit the lowest outstanding TSN, we
need to restart the T3-RTX timer, so that subsequent timeouts will
correctly tag all the packets necessary for retransmissions.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Tested-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correctly keep track of Fast Recovery state and do not reduce
congestion window multiple times during sucht state.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Tested-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 UDP sockets wth IPv4 mapped address use udp_sendmsg to send the data
actually. In this case ip_flush_pending_frames should be called instead
of ip6_flush_pending_frames.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
- Allow longer lifetimes (>= 0x7fffffff/HZ) on 64bit archs
by using unsigned long.
- Shadow this arithmetic overflow workaround by introducing
helper functions: addrconf_timeout_fixup() and
addrconf_finite_timeout().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Commit 7cbca67c07 ("[IPV6]: Support
Source Address Selection API (RFC5014)") introduced NULL dereference
of asoc to sctp_v6_get_saddr in net/sctp/ipv6.c.
Pointed out by Johann Felix Soden <johfel@users.sourceforge.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Make nlmsg_trim(), nlmsg_cancel(), genlmsg_cancel(), and
nla_nest_cancel() void functions.
Return -EMSGSIZE instead of -1 if the provided message buffer is not
big enough.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of nla_parse_nested_compat() is to parse attributes which
contain a struct followed by a stream of nested attributes. So far,
it called nla_parse_nested() to parse the stream of nested attributes
which was wrong, as nla_parse_nested() expects a container attribute
as data which holds the attribute stream. It needs to call
nla_parse() directly while pointing at the next possible alignment
point after the struct in the beginning of the attribute.
With this patch, I can no longer reproduce the reported leftover
warnings.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed from Al Viro <viro@ftp.linux.org.uk> via David Miller
<davem@davemloft.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit e38bad4766
mac80211: make ieee80211_iterate_active_interfaces not need rtnl
rt2500usb and rt73usb broke down due to attempting register access
in atomic context (which is not possible for USB hardware).
This patch restores ieee80211_iterate_active_interfaces() to use RTNL lock,
and provides the non-RTNL version under a new name:
ieee80211_iterate_active_interfaces_atomic()
So far only rt2x00 uses ieee80211_iterate_active_interfaces(), and those
drivers require the RTNL version of ieee80211_iterate_active_interfaces().
Since they already call that function directly, this patch will automatically
fix the USB rt2x00 drivers.
v2: Rename ieee80211_iterate_active_interfaces_rtnl
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was some cleanup issues during early mount which would trigger
a kernel bug for certain types of failure. This patch reorganizes the
cleanup to get rid of the bad behavior.
This also merges the 9pnet and 9pnet_fd modules for the purpose of
configuration and initialization. Keeping the fd transport separate
from the core 9pnet code seemed like a good idea at the time, but in
practice has caused more harm and confusion than good.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The kernel-doc comments of much of the 9p system have been in disarray since
reorganization. This patch fixes those problems, adds additional documentation
and a template book which collects the 9p information.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Replace u16ho with put/get_unaligned functions
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syncppp layer wants a mid-level netdev private pointer.
It was using netdev->priv but that only worked by accident,
and thus this scheme was broken when the device private
allocation strategy changed.
Add a proper mid-layer private pointer for uses like this,
update syncppp and all users, and remove the HDLC_PPP broken
tag from drivers/net/wan/Kconfig
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
tcp: Overflow bug in Vegas
[IPv4] UFO: prevent generation of chained skb destined to UFO device
iwlwifi: move the selects to the tristate drivers
ipv4: annotate a few functions __init in ipconfig.c
atm: ambassador: vcc_sf semaphore to mutex
MAINTAINERS: The socketcan-core list is subscribers-only.
netfilter: nf_conntrack: padding breaks conntrack hash on ARM
ipv4: Update MTU to all related cache entries in ip_rt_frag_needed()
sch_sfq: use del_timer_sync() in sfq_destroy()
net: Add compat support for getsockopt (MCAST_MSFILTER)
net: Several cleanups for the setsockopt compat support.
ipvs: fix oops in backup for fwmark conn templates
bridge: kernel panic when unloading bridge module
bridge: fix error handling in br_add_if()
netfilter: {nfnetlink,ip,ip6}_queue: fix skb_over_panic when enlarging packets
netfilter: x_tables: fix net namespace leak when reading /proc/net/xxx_tables_names
netfilter: xt_TCPOPTSTRIP: signed tcphoff for ipv6_skip_exthdr() retval
tcp: Limit cwnd growth when deferring for GSO
tcp: Allow send-limited cwnd to grow up to max_burst when gso disabled
[netdrvr] gianfar: Determine TBIPA value dynamically
...
* 'audit.b50' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] new predicate - AUDIT_FILETYPE
[patch 2/2] Use find_task_by_vpid in audit code
[patch 1/2] audit: let userspace fully control TTY input auditing
[PATCH 2/2] audit: fix sparse shadowed variable warnings
[PATCH 1/2] audit: move extern declarations to audit.h
Audit: MAINTAINERS update
Audit: increase the maximum length of the key field
Audit: standardize string audit interfaces
Audit: stop deadlock from signals under load
Audit: save audit_backlog_limit audit messages in case auditd comes back
Audit: collect sessionid in netlink messages
Audit: end printk with newline
commit 0794935e "[NETFILTER]: nf_conntrack: optimize hash_conntrack()"
results in ARM platforms hashing uninitialised padding. This padding
doesn't exist on other architectures.
Fix this by replacing NF_CT_TUPLE_U_BLANK() with memset() to ensure
everything is initialised. There were only 4 bytes that
NF_CT_TUPLE_U_BLANK() wasn't clearing anyway (or 12 bytes on ARM).
Signed-off-by: Philip Craig <philipc@snapgear.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct net_device parameter to ip_rt_frag_needed() and update MTU to
cache entries where ifindex is specified. This is similar to what is
already done in ip_rt_redirect().
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for getsockopt for MCAST_MSFILTER for
both IPv4 and IPv6. It depends on the previous setsockopt patch,
and uses the same method.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=10556
where conn templates with protocol=IPPROTO_IP can oops backup box.
Result from ip_vs_proto_get() should be checked because
protocol value can be invalid or unsupported in backup. But
for valid message we should not fail for templates which use
IPPROTO_IP. Also, add checks to validate message limits and
connection state. Show state NONE for templates using IPPROTO_IP.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
iwlwifi: Allow building iwl3945 without iwl4965.
wireless: Fix compile error with wifi & leds
tcp: Fix slab corruption with ipv6 and tcp6fuzz
ipv4/ipv6 compat: Fix SSM applications on 64bit kernels.
[IPSEC]: Use digest_null directly for auth
sunrpc: fix missing kernel-doc
can: Fix copy_from_user() results interpretation
Revert "ipv6: Fix typo in net/ipv6/Kconfig"
tipc: endianness annotations
ipv6: result of csum_fold() is already 16bit, no need to cast
[XFRM] AUDIT: Fix flowlabel text format ambibuity.
Previously I added sessionid output to all audit messages where it was
available but we still didn't know the sessionid of the sender of
netlink messages. This patch adds that information to netlink messages
so we can audit who sent netlink messages.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add support on 64-bit kernels for seting 32-bit compatible MCAST*
socket options.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds IPv6 support to the interfaces that are used to express nfsd
exports. All addressed are stored internally as IPv6; backwards
compatibility is maintained using mapped addresses.
Thanks to Bruce Fields, Brian Haley, Neil Brown and Hideaki Joshifuji
for comments
Signed-off-by: Aurelien Charbon <aurelien.charbon@bull.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Brian Haley <brian.haley@hp.com>
Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
As it stands it's impossible to use any authentication algorithms
with an ID above 31 portably. It just happens to work on x86 but
fails miserably on ppc64.
The reason is that we're using a bit mask to check the algorithm
ID but the mask is only 32 bits wide.
After looking at how this is used in the field, I have concluded
that in the long term we should phase out state matching by IDs
because this is made superfluous by the reqid feature. For current
applications, the best solution IMHO is to allow all algorithms when
the bit masks are all ~0.
The following patch does exactly that.
This bug was identified by IBM when testing on the ppc64 platform
using the NULL authentication algorithm which has an ID of 251.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This deblats ~200 bytes when ipv6 and dccp are 'y'.
Besides, this will ease compilation issues for patches
I'm working on to make inet hash tables more scalable
wrt net namespaces.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I can see from the code, two places (tcp_v6_syn_recv_sock and
dccp_v6_request_recv_sock) that call this one already run with
BHs disabled, so it's safe to call __inet_inherit_port there.
Besides (in case I missed smth with code review) the calltrace
tcp_v6_syn_recv_sock
`- tcp_v4_syn_recv_sock
`- __inet_inherit_port
and the similar for DCCP are valid, but assumes BHs to be disabled.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to send BSS changes to driver from beacons processed
during scanning. We are more interested in beacons from an AP with which
we are associated - these will still be used to send updates to driver as
the beacons are received without scanning.
This change·removes the requirement that bss_info_changed needs to be atomic.
The beacons received during scanning are processed from a tasklet, but if we
do not call bss_info_changed for these beacons there is no need for it to be
atomic. This function (bss_info_changed) is called either from workqueue or
ioctl in all other instances.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>