When a page has a memory uncorrectable ECC error, the recovery
code wants to prevent the page from being reused. This change
bumps the reference count to prevent the page from getting back
on the free list.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
paddr needs to be shifted by PAGE_SHIFT to be valid
input for pfn_valid().
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The determination of whether an MCA is recoverable or not must
be based on the bits set in the PSP (Processor State Parameter).
The specific bits are shown in the Intel IA-64 Architecture Software
Developer's Manual, Vol 2, Table 11-6 Software Recovery Bits in
Processor State Parameter. Those bits should be consistent
across the entire IA-64 family of processors.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
At the moment, attempting to invoke a signal-handler on the normal
stack is guaranteed to fail if the stack-pointer happens not to be
16-byte aligned. This is because the signal-trampoline will attempt
to store fp-regs with stf.spill instructions, which will trap for
misaligned addresses. This isn't terribly useful behavior. It's
better to just always align the signal frame to the next lower 16-byte
boundary.
Signed-off-by: David Mosberger-Tang <David.Mosberger@acm.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The original memory less node allocation attempted to use NODEDATA_ALIGN for
alignment. The bootmem allocator only allows a power of two alignments. This
causes a BUG_ON for some nodes. For cpu only nodes just allocate with a
PERCPU_PAGE_SIZE alignment.
Some older firmware reports SLIT distances of 0xff and results in bestnode
not being computed. This is now treated correctly.
The failed allocation check was removed because it's redundant. The
bootmem allocator already makes this check.
This fix has been boot tested on 4 node machine which has 4 cpu only nodes
and 1 memory node. Thanks to Pete Keilty for reporting this and helping me
test it.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
notify_die() added for MCA_{MONARCH,SLAVE,RENDEZVOUS}_{ENTER,PROCESS,LEAVE} and
INIT_{MONARCH,SLAVE}_{ENTER,PROCESS,LEAVE}. We need multiple
notification points for these events because they can take many seconds
to run which has nasty effects on the behaviour of the rest of the
system.
DIE_SS replaced by a generic DIE_FAULT which checks the vector number,
to allow interception of faults other than SS.
DIE_MACHINE_{HALT,RESTART} added to allow last minute close down
processing, especially when the halt/restart routines are called from
error handlers.
DIE_OOPS added.
The check for kprobe's break numbers has been moved from traps.c to
kprobes.c, allowing DIE_BREAK to be used for any additional break
numbers, i.e. it is no longer kprobes specific.
Hooks for kernel debuggers and kernel dumpers added, ENTER and LEAVE.
Both of these disable the system for long periods which impact on
watchdogs and heartbeat systems in general. More patches to come that
use these events to reset watchdogs and heartbeats.
unregister_die_notifier() added and both routines exported. Requested
by Dean Nelson.
Lock removed from {un,}register_die_notifier. notifier_chain_register()
already takes a lock. Also the generic notifier chain locking is being
reworked to distinguish between callbacks that can block and those that
cannot, the lock in {un,}register_die_notifier would interfere with
that change. http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
Leading white space removed from arch/ia64/kernel/kprobes.c.
Typo in mca.c in original version of this patch found & fixed by Dean
Nelson.
Signed-off-by: Keith Owens <kaos@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Acked-by: Anil Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reorganize the preempt_disable/enable calls to eliminate the extra preempt
depth. Changes based on Paul McKenney's review suggestions for the kprobes
RCU changeset.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the arch kprobes infrastructure to take advantage of the locking
changes introduced by usage of RCU for synchronization. All handlers are now
run without any locks held, so they have to be re-entrant or provide their own
synchronization.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IA64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following set of patches are aimed at improving kprobes scalability. We
currently serialize kprobe registration, unregistration and handler execution
using a single spinlock - kprobe_lock.
With these changes, kprobe handlers can run without any locks held. It also
allows for simultaneous kprobe handler executions on different processors as
we now track kprobe execution on a per processor basis. It is now necessary
that the handlers be re-entrant since handlers can run concurrently on
multiple processors.
All changes have been tested on i386, ia64, ppc64 and x86_64, while sparc64
has been compile tested only.
The patches can be viewed as 3 logical chunks:
patch 1: Reorder preempt_(dis/en)able calls
patches 2-7: Introduce per_cpu data areas to track kprobe execution
patches 8-9: Use RCU to synchronize kprobe (un)registration and handler
execution.
Thanks to Maneesh Soni, James Keniston and Anil Keshavamurthy for their
review and suggestions. Thanks again to Anil, Hien Nguyen and Kevin Stafford
for testing the patches.
This patch:
Reorder preempt_disable/enable() calls in arch kprobes files in preparation to
introduce locking changes. No functional changes introduced by this patch.
Signed-off-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton suggested to move kprobes from kernel hacking menu, since
kernel hacking menu is in-appropriate for the Kprobes. This patch moves
Kprobes and Oprofile under instrumentation menu.
(akpm: it's not a natural fit, but things like djprobes and the s390 guys'
statistics library need a home)
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current ia64 implementation of dma_get_cache_alignment does not work
for modules because it relies on a symbol which is not exported. Direct
access to a global is a little ugly anyway, so this patch re-implements
dma_get_cache_alignment in a manner similar to what is currently used for
x86_64.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restrict CONFIG_SGI_SN_XP to IA64_GENERIC or IA64_SGI_SN2 kernels.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
wrap_mmu_context(), delayed_tlb_flush(), get_mmu_context() all
have an extra { } block which cause one extra indentation.
get_mmu_context() is particularly bad with 5 indentations to
the most inner "if". It finally gets on my nerve that I can't
keep the code within 80 columns. Remove the extra { } block
and while I'm at it, reformat all the comments to 80-column
friendly. No functional change at all with this patch.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Corrects the very inefficent method of finding free context_ids in
get_mmu_context(). Instead of walking the task_list of all processes,
2 bitmaps are used to efficently store and lookup state, inuse and
needs flushing. The entire rid address space is now used before calling
wrap_mmu_context and global tlb flushing.
Special thanks to Ken and Rohit for their review and modifications in
using a bit flushmap.
Signed-off-by: Peter Keilty <peter.keilty@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pgdat->node_size_lock is basically only neeeded in one place in the normal
code: show_mem(), which is the arch-specific sysrq-m printing function.
Strictly speaking, the architectures not doing memory hotplug do no need this
locking in show_mem(). However, they are all included for completeness. This
should also make any future consolidation of all of the implementations a
little more straightforward.
This lock is also held in the sparsemem code during a memory removal, as
sections are invalidated. This is the place there pfn_valid() is made false
for a memory area that's being removed. The lock is only required when doing
pfn_valid() operations on memory which the user does not already have a
reference on the page, such as in show_mem().
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was one small but very significant change in the previous patch:
mprotect's flush_tlb_range fell outside the page_table_lock: as it is in 2.4,
but that doesn't prove it safe in 2.6.
On some architectures flush_tlb_range comes to the same as flush_tlb_mm, which
has always been called from outside page_table_lock in dup_mmap, and is so
proved safe. Others required a deeper audit: I could find no reliance on
page_table_lock in any; but in ia64 and parisc found some code which looks a
bit as if it might want preemption disabled. That won't do any actual harm,
so pending a decision from the maintainers, disable preemption there.
Remove comments on page_table_lock from flush_tlb_mm, flush_tlb_range and
flush_tlb_page entries in cachetlb.txt: they were rather misleading (what
generic code does is different from what usually happens), the rules are now
changing, and it's not yet clear where we'll end up (will the generic
tlb_flush_mmu happen always under lock? never under lock? or sometimes under
and sometimes not?).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
First step in pushing down the page_table_lock. init_mm.page_table_lock has
been used throughout the architectures (usually for ioremap): not to serialize
kernel address space allocation (that's usually vmlist_lock), but because
pud_alloc,pmd_alloc,pte_alloc_kernel expect caller holds it.
Reverse that: don't lock or unlock init_mm.page_table_lock in any of the
architectures; instead rely on pud_alloc,pmd_alloc,pte_alloc_kernel to take
and drop it when allocating a new one, to check lest a racing task already
did. Similarly no page_table_lock in vmalloc's map_vm_area.
Some temporary ugliness in __pud_alloc and __pmd_alloc: since they also handle
user mms, which are converted only by a later patch, for now they have to lock
differently according to whether or not it's init_mm.
If sources get muddled, there's a danger that an arch source taking
init_mm.page_table_lock will be mixed with common source also taking it (or
neither take it). So break the rules and make another change, which should
break the build for such a mismatch: remove the redundant mm arg from
pte_alloc_kernel (ppc64 scrapped its distinct ioremap_mm in 2.6.13).
Exceptions: arm26 used pte_alloc_kernel on user mm, now pte_alloc_map; ia64
used pte_alloc_map on init_mm, now pte_alloc_kernel; parisc had bad args to
pmd_alloc and pte_alloc_kernel in unused USE_HPPA_IOREMAP code; ppc64
map_io_page forgot to unlock on failure; ppc mmu_mapin_ram and ppc64 im_free
took page_table_lock for no good reason.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia64 has expand_backing_store function for growing its Register Backing Store
vma upwards. But more complete code for this purpose is found in the
CONFIG_STACK_GROWSUP part of mm/mmap.c. Uglify its #ifdefs further to provide
expand_upwards for ia64 as well as expand_stack for parisc.
The Register Backing Store vma should be marked VM_ACCOUNT. Implement the
intention of growing it only a page at a time, instead of passing an address
outside of the vma to handle_mm_fault, with unknown consequences.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The original vm_stat_account has fallen into disuse, with only one user, and
only one user of vm_stat_unaccount. It's easier to keep track if we convert
them all to __vm_stat_account, then free it from its __shackles.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... and related annotations for amd64 - swiotlb code is shared, but
prototypes are not.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In arch/ia64/kernel/ptrace.c there is a test for a peek or poke of a
register image (in register backing storage).
The test can be unnecessarily long (and occurs while holding the tasklist_lock).
Especially long on a large system with thousands of active tasks.
The ptrace caller (presumably a debugger) specifies the pid of
its target and an address to peek or poke. But the debugger could be
attached to several tasks.
The idea of find_thread_for_addr() is to find whether the target address
is in the RBS for any of those tasks.
Currently it searches the thread-list of the target pid. If that search
does not find a match, and the shared mm-struct's user count indicates
that there are other tasks sharing this address space (a rare occurrence),
a search is made of all the tasks in the system.
Another approach can drastically shorten this procedure.
It depends upon the fact that in order to peek or poke from/to any task,
the debugger must first attach to that task. And when it does, the
attached task is made a child of the debugger (is chained to its children list).
Therefore we can search just the debugger's children list.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
flush_tlb_all() can be a scaling issue on large SGI Altix systems
since it uses the global call_lock and always executes on all cpus.
When a process enters flush_tlb_range() to purge TLBs for another
process, it is possible to avoid flush_tlb_all() and instead allow
sn2_global_tlb_purge() to purge TLBs only where necessary.
This patch modifies flush_tlb_range() so that this case can be handled
by platform TLB purge functions and updates ia64_global_tlb_purge()
accordingly. sn2_global_tlb_purge() now calculates the region register
value from the mm argument introduced with this patch.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
bte_copy() calls calls get_nasid(), which will get flagged if
preemption if enabled. raw_smp_processor_id() is used instead.
It is OK if we migrate off node.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Eliminate the passing in of a scratch buffer used for locating the
reserved page setup for XPC.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
XPC needs to be changed to support up to 16k nasids on an SGI Altix system.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch addresses a few issues with the open/close protocol that
were revealed by the newly added disengage functionality combined
with more extensive testing.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In arch/ia64 change the explicit use of a for-loop using NR_CPUS into the
general for_each_online_cpu() construct. This widens the scope of potential
future optimizations of the general constructs, as well as takes advantage
of the existing optimizations of first_cpu() and next_cpu(), which is
advantageous when the true CPU count is much smaller than NR_CPUS.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In arch/ia64 change the explicit use of for-loops and NR_CPUS into the
general for_each_cpu() or for_each_online_cpu() constructs, as
appropriate. This widens the scope of potential future optimizations
of the general constructs, as well as takes advantage of the existing
optimizations of first_cpu() and next_cpu().
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The new ia64 assembler uses slot 1 for the offset of a long (2-slot)
instruction and the old assembler uses slot 2. The 2.6 kernel assumes
slot 2 and won't boot when the new assembler is used:
http://sources.redhat.com/bugzilla/show_bug.cgi?id=1433
This patch will work with either slot 1 or 2.
Patch provided by H.J. Lu
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the "siblings" field value in /proc/cpuinfo so that it now shows the
number of siblings as seen by OS, instead of what is available from
hardware perspective.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The simscsi code at present overflows an int if it's given a large
disk image. The attached patch increases the possible size to 128G.
While it's unlikely that anyone will want to use SKI with such a
large drive, the same framework is currently being used for various
virtualisation experiments.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
changes to swiotlb.c made in commit 281dd25cdc
since this file has been moved from arch/ia64/lib/swiotlb.c to
lib/swiotlb.c
Signed-off-by: Tony Luck <tony.luck@intel.com>
This introduces a limit parameter to the core bootmem allocator; The new
parameter indicates that physical memory allocated by the bootmem
allocator should be within the requested limit.
We also introduce alloc_bootmem_low_pages_limit, alloc_bootmem_node_limit,
alloc_bootmem_low_pages_node_limit apis, but alloc_bootmem_low_pages_limit
is the only api used for swiotlb.
The existing alloc_bootmem_low_pages() api could instead have been
changed and made to pass right limit to the core allocator. But that
would make the patch more intrusive for 2.6.14, as other arches use
alloc_bootmem_low_pages(). We may be done that post 2.6.14 as a
cleanup.
With this, swiotlb gets memory within 4G for both x86_64 and ia64
arches.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've noticed a kernel hang during a storm of CMC interrupts, which was
tracked down to the continual execution of the interrupt handler.
There's code in the CMC handler that's supposed to disable CMC
interrupts and switch to polling mode when it sees a bunch of CMCs.
Because disabling CMCs across all CPUs isn't safe in interrupt context,
the disable is done with a schedule_work(). But with continual CMC
interrupts, the schedule_work() never gets executed.
The following patch immediately disables CMC interrupts for the current
CPU. This then allows (at least) one CPU to ignore CMC interrupts,
execute the schedule_work() code, and disable CMC interrupts on the rest
of the CPUs.
Acked-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Bryan Sutula <Bryan.Sutula@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
gensparse_defconfig is a config generated file for SPARSEMEM and GENERIC
kernel configuration (defconfig).
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is the minimal set of changes required by ia64 to use SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
For FLATMEM contig_page_data has been made transparent to the arch code.
This patch conforms to that change.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The patch modifies the Kconfig file to introduce the new memory model
options and other related SPARSEMEM changes. There is also a minor change
in the Makefile.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The swiotlb implementation is shared by both IA-64 and EM64T. However,
the source itself lives under arch/ia64. This patch moves swiotlb.c
from arch/ia64/lib to lib/ and fixes-up the appropriate Makefile and
Kconfig files. No actual changes are made to swiotlb.c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
/proc/iomem describes a block of memory as "Kernel data",
but the end address is derived from "_edata". The kernel
actually has many other sections beyond _edata. Get the
real end address from _end.
Acked-by: Khalid Aziz <khalid_aziz@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch adds a #define for SN_SAL_IOIF_PCI_SAFE and makes that the
preferred method of implementing sn_pci_legacy_read() and
sn_pci_legacy_write().
This SAL call has been present in SGI proms since version 4.10. If the
SN_SAL_IOIF_PCI_SAFE call fails, revert to the previous code for compatability
with older proms.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Address space resources for ACPI devices have a producer/consumer
flag. All devices "consume" the indicated address space. If the
resource is marked as a "producer", the range is also passed on
to child devices.
We currently ignore this flag when setting up MMIO and I/O port
windows for PCI root bridges, so we could mistakenly interpret
a "consumed-only" range, like CSR space for the device itself,
as a window that is routed to children.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Verify the pfn is valid before calling pfn_to_page(),
and cut isolation message if nothing was done.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Wire the MCA/INIT handler stacks into DTR[2] and track them in
IA64_KR(CURRENT_STACK). This gives the MCA/INIT handler stacks the
same TLB status as normal kernel stacks. Reload the old CURRENT_STACK
data on return from OS to SAL.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The sd driver now uses scsi_execute_req() for almost everything.
scsi_execute_req() converts requests into scatterlists.
Fix the HP SCSI disk simulator to understand scatterlists for
more commands.
Without this patch the current kernel will not boot on the simulator
(the disks are always detected as having no sectors, and so cannot be
mounted).
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Move acpi_map_iosapics() from pci.c to acpi.c, since it doesn't
have anything to do with PCI.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update comment about how ar.k0 is used. Make the initialization the
same as in start_secondary() (no functional change, just make it look
more similar).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
User mode kexec tools expect to find information about physical
memory in /proc/iomem (as they do on x86) to validate the addresses
that the new kernel will use.
Signed-off-by: Khalid Aziz <khalid.aziz@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
With the new fdtable locking rules, you have to protect fdtable with either
->file_lock or rcu_read_lock/unlock(). There are some places where we
aren't doing either. This patch fixes those places.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch increases the maximum number of cpus supported on IA64
to 1024. No changes are made to the default SSI size. The patch
simply allows specifying up to 1024p.
There are certainly scaling (& other) issues that also need to be
addressed!!! Additional patches will follow.....
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There were some trailing white spaces, long lines, brackets in
weird style etc. This patch cleans them up.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes some compilation warnings, mostly
trivially. acpi.c fix also noted by Kenji Kaneshige.
Signed-off-by; Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some of the SN code & #defines related to compact nodes & IO discovery
have gotten stale over the years. This patch attempts to clean them up.
Some of the various SN MAX_xxx #defines were also unclear & misused.
The primary changes are:
- use MAX_NUMNODES. This is the generic linux #define for the number
of nodes that are known to the generic kernel. Arrays & loops
for constructs that are 1:1 with linux-defined nodes should
use the linux #define - not an SN equivalent.
- use MAX_COMPACT_NODES for MAX_NUMNODES + NUM_TIOS. This is the
number of nodes in the SSI system. Compact nodes are a hack to
get around the IA64 architectural limit of 256 nodes. Large SGI
systems have more than 256 nodes. When we upgrade to ACPI3.0,
I _hope_ that all nodes will be real nodes that are known to
the generic kernel. That will allow us to delete the notion
of "compact nodes".
- add MAX_NUMALINK_NODES for the total number of nodes that
are in the numalink domain - all partitions.
- simplified (understandable) scan_for_ionodes()
- small amount of cleanup related to cnodes
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
PNP and PNPACPI turned on
i8042 recently changed from ACPI to PNP detection. Without PNP, it
probes legacy I/O ports for the keyboard controller, which causes an
MCA on HP boxes.
Also, I'm about to remove 8250_acpi.c, so we'll need PNP to detect
non-PCI serial ports. Until 8250_acpi.c is removed, some systems
will see serial ports reported twice (once from 8250_acpi.c and again
from 8250_pnp.c). This is harmless.
PNPACPI is still marked EXPERIMENTAL, but I'm not aware of any
outstanding issues on ia64.
IDE_GENERIC turned off (except for SGI simulator, all ia64 IDE is PCI)
ide-generic probes compiled-in legacy I/O ports for IDE devices, which
again causes an MCA. It would be nicer to just get rid of all the
legacy junk from include/asm-ia64/ide.h, but that is a bit riskier
because it could break ide-cs and the HDIO_REGISTER_HWIF ioctl
(http://www.ussg.iu.edu/hypermail/linux/kernel/0508.2/0049.html).
Here's the essence of the patch:
-# CONFIG_PNP is not set
+CONFIG_PNP=y
+CONFIG_PNPACPI=y
-CONFIG_IDE_GENERIC=y
+# CONFIG_IDE_GENERIC is not set
Tested on tiger, bigsur, and zx1.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Several implementations were essentialy a common piece of C code using
the cmpxchg() macro. Put the implementation in one spot that everyone
can share, and convert sparc64 over to using this.
Alpha is the lone arch-specific implementation, which codes up a
special fast path for the common case in order to avoid GP reloading
which a pure C version would require.
Signed-off-by: David S. Miller <davem@davemloft.net>
Machine vector selection has always been a bit of a hack given how
early in system boot it needs to be done. Services like ACPI namespace
are not available and there are non-trivial problems to moving them to
early boot. However, there's no reason we can't change to a different
machvec later in boot when the services we need are available. By
adding a entry point for later initialization of the swiotlb, we can add
an error path for the hpzx1 machevec initialization and fall back to the
DIG machine vector if IOMMU hardware isn't found in the system. Since
ia64 uses 4GB for zone DMA (no ISA support), it's trivial to allocate a
contiguous range from the slab for bounce buffer usage.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pavel Emelianov and Kirill Korotaev observe that fs and arch users of
security_vm_enough_memory tend to forget to vm_unacct_memory when a
failure occurs further down (typically in setup_arg_pages variants).
These are all users of insert_vm_struct, and that reservation will only
be unaccounted on exit if the vma is marked VM_ACCOUNT: which in some
cases it is (hidden inside VM_STACK_FLAGS) and in some cases it isn't.
So x86_64 32-bit and ppc64 vDSO ELFs have been leaking memory into
Committed_AS each time they're run. But don't add VM_ACCOUNT to them,
it's inappropriate to reserve against the very unlikely case that gdb
be used to COW a vDSO page - we ought to do something about that in
do_wp_page, but there are yet other inconsistencies to be resolved.
The safe and economical way to fix this is to let insert_vm_struct do
the security_vm_enough_memory check when it finds VM_ACCOUNT is set.
And the MIPS irix_brk has been calling security_vm_enough_memory before
calling do_brk which repeats it, doubly accounting and so also leaking.
Remove that, and all the fs and arch calls to security_vm_enough_memory:
give it a less misleading name later on.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we use 64bit kernel on ia64/x86_64/s390 architecture, and we run
32bit binary on 32bit compatibility mode, sendfile system call seems be
not set offset argument.
This is because sendfile's return value is not zero but the code regards
the result by return value is zero or not.
This problem will be affect to ia64/x86_64/s390 and not affect to other
architecture does not affect other architecture (mips/parisc/ppc64/sparc64).
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete the special case unwind code that was only used by the old
MCA/INIT handler.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The bulk of the change. Use per cpu MCA/INIT stacks. Change the SAL
to OS state (sos) to be per process. Do all the assembler work on the
MCA/INIT stacks, leaving the original stack alone. Pass per cpu state
data to the C handlers for MCA and INIT, which also means changing the
mca_drv interfaces slightly. Lots of verification on whether the
original stack is usable before converting it to a sleeping process.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reading the INIT record from SAL during the INIT event has proved to be
unreliable, and a source of hangs during INIT processing. The new
MCA/INIT handlers remove the need to get the INIT record from SAL.
Change salinfo.c so mca.c can just flag that a new record is available,
without having to read the record during INIT processing. This patch
can be applied without the new MCA/INIT handlers.
Also clean up some usage of NR_CPUS which should have been using
cpu_online().
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When introducing the generic asm-offsets.h support the dependency
chain for the prepare targets was changed. All build scripts expecting
include/asm/asm-offsets.h to be made when using the prepare target would broke.
With the limited number of prepare targets left in arch Makefiles
the trivial solution was to introduce a new arch specific target: archprepare
The dependency chain looks like this now:
prepare
|
+--> prepare0
|
+--> archprepare
|
+--> scripts_basic
+--> prepare1
|
+---> prepare2
|
+--> prepare3
So prepare 3 is processed before prepare2 etc.
This guaantees that the asm symlink, version.h, scripts_basic
are all updated before archprepare is processed.
prepare0 which build the asm-offsets.h file will need the
actions performed by archprepare.
The head target is now named prepare, because users scripts will most
likely use that target, but prepare-all has been kept for compatibility.
Updated Documentation/kbuild/makefiles.txt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch (written by me and also containing many suggestions of Arjan van
de Ven) does a major cleanup of the spinlock code. It does the following
things:
- consolidates and enhances the spinlock/rwlock debugging code
- simplifies the asm/spinlock.h files
- encapsulates the raw spinlock type and moves generic spinlock
features (such as ->break_lock) into the generic code.
- cleans up the spinlock code hierarchy to get rid of the spaghetti.
Most notably there's now only a single variant of the debugging code,
located in lib/spinlock_debug.c. (previously we had one SMP debugging
variant per architecture, plus a separate generic one for UP builds)
Also, i've enhanced the rwlock debugging facility, it will now track
write-owners. There is new spinlock-owner/CPU-tracking on SMP builds too.
All locks have lockup detection now, which will work for both soft and hard
spin/rwlock lockups.
The arch-level include files now only contain the minimally necessary
subset of the spinlock code - all the rest that can be generalized now
lives in the generic headers:
include/asm-i386/spinlock_types.h | 16
include/asm-x86_64/spinlock_types.h | 16
I have also split up the various spinlock variants into separate files,
making it easier to see which does what. The new layout is:
SMP | UP
----------------------------|-----------------------------------
asm/spinlock_types_smp.h | linux/spinlock_types_up.h
linux/spinlock_types.h | linux/spinlock_types.h
asm/spinlock_smp.h | linux/spinlock_up.h
linux/spinlock_api_smp.h | linux/spinlock_api_up.h
linux/spinlock.h | linux/spinlock.h
/*
* here's the role of the various spinlock/rwlock related include files:
*
* on SMP builds:
*
* asm/spinlock_types.h: contains the raw_spinlock_t/raw_rwlock_t and the
* initializers
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* asm/spinlock.h: contains the __raw_spin_*()/etc. lowlevel
* implementations, mostly inline assembly code
*
* (also included on UP-debug builds:)
*
* linux/spinlock_api_smp.h:
* contains the prototypes for the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*
* on UP builds:
*
* linux/spinlock_type_up.h:
* contains the generic, simplified UP spinlock type.
* (which is an empty structure on non-debug builds)
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* linux/spinlock_up.h:
* contains the __raw_spin_*()/etc. version of UP
* builds. (which are NOPs on non-debug, non-preempt
* builds)
*
* (included on UP-non-debug builds:)
*
* linux/spinlock_api_up.h:
* builds the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*/
All SMP and UP architectures are converted by this patch.
arm, i386, ia64, ppc, ppc64, s390/s390x, x64 was build-tested via
crosscompilers. m32r, mips, sh, sparc, have not been tested yet, but should
be mostly fine.
From: Grant Grundler <grundler@parisc-linux.org>
Booted and lightly tested on a500-44 (64-bit, SMP kernel, dual CPU).
Builds 32-bit SMP kernel (not booted or tested). I did not try to build
non-SMP kernels. That should be trivial to fix up later if necessary.
I converted bit ops atomic_hash lock to raw_spinlock_t. Doing so avoids
some ugly nesting of linux/*.h and asm/*.h files. Those particular locks
are well tested and contained entirely inside arch specific code. I do NOT
expect any new issues to arise with them.
If someone does ever need to use debug/metrics with them, then they will
need to unravel this hairball between spinlocks, atomic ops, and bit ops
that exist only because parisc has exactly one atomic instruction: LDCW
(load and clear word).
From: "Luck, Tony" <tony.luck@intel.com>
ia64 fix
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjanv@infradead.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the final 20 DEFINE_SPINLOCK holdouts. (another 580 places
are already using DEFINE_SPINLOCK). Build tested on x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order for the RCU to work, the file table array, sets and their sizes must
be updated atomically. Instead of ensuring this through too many memory
barriers, we put the arrays and their sizes in a separate structure. This
patch takes the first step of putting the file table elements in a separate
structure fdtable that is embedded withing files_struct. It also changes all
the users to refer to the file table using files_fdtable() macro. Subsequent
applciation of RCU becomes easier after this.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For architecture like ia64, the switch stack structure is fairly large
(currently 528 bytes). For context switch intensive application, we found
that significant amount of cache misses occurs in switch_to() function.
The following patch adds a hook in the schedule() function to prefetch
switch stack structure as soon as 'next' task is determined. This allows
maximum overlap in prefetch cache lines for that structure.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete obsolete stuff from arch Makefile
Rename file to asm-offsets.h
The trick used in the arch Makefile to circumvent the circular
dependency is kept.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Increase the value for the maximum physical address on SN systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
These are SN2 only drivers. They should have platform checks to prevent
them from doing evil stuff in GENERIC kernels.
Signed-off-by: Martin Hicks <mort@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Turn off the QLOGIC_FC driver. Supposedly qla2xxx should support
these devices. Do any ia64 machines have one of these devices as
the boot device?
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
New version leaves the original memory map unmodified.
Also saves any granule trimmings for use by the uncached
memory allocator.
Inspired by Khalid Aziz (various traces of his patch still
remain). Fixes to uncached_build_memmap() and sn2 testing
by Martin Hicks.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes a race condition where in system used to hang or sometime
crash within minutes when kprobes are inserted on ISR routine and a task
routine.
The fix has been stress tested on i386, ia64, pp64 and on x86_64. To
reproduce the problem insert kprobes on schedule() and do_IRQ() functions
and you should see hang or system crash.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch addresses a potential race condition for a case where Kprobe has
been removed right after another CPU has taken a break hit.
The way this is addressed here is when the CPU that has taken a break hit
does not find its corresponding kprobe, then we check to see if the
original instruction got replaced with other than break. If it got
replaced with other than break instruction, then we continue to execute
from the replaced instruction, else if we find that it is still a break,
then we let the kernel handle this, as this might be the break instruction
inserted by other than kprobe(may be kernel debugger).
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the ia64 architecture specific changes to prevent the
possible race conditions.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
64 bit architectures all implement their own compatibility sys_open(),
when in fact the difference is simply not forcing the O_LARGEFILE
flag. So use the a common function instead.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've already sent this to the maintainers, and this is now being sent to a
larger community audience. I have fixed a problem with the ia64 version of
build_sched_domains(), but a similar fix still needs to be made to the
generic build_sched_domains() in kernel/sched.c.
The "dynamic sched domains" functionality has recently been merged into
2.6.13-rcN that sees the dynamic declaration of a cpu-exclusive (a.k.a.
"isolated") cpuset and rebuilds the CPU Scheduler sched domains and sched
groups to separate away the CPUs in this cpu-exclusive cpuset from the
remainder of the non-isolated CPUs. This allows the non-isolated CPUs to
completely ignore the isolated CPUs when doing load-balancing.
Unfortunately, build_sched_domains() expects that a sched domain will
include all the CPUs of each node in the domain, i.e., that no node will
belong in both an isolated cpuset and a non-isolated cpuset. Declaring a
cpuset that violates this presumption will produce flawed data structures
and will oops the kernel.
To trigger the problem (on a NUMA system with >1 CPUs per node):
cd /dev/cpuset
mkdir newcpuset
cd newcpuset
echo 0 >cpus
echo 0 >mems
echo 1 >cpu_exclusive
I have fixed this shortcoming for ia64 NUMA (with multiple CPUs per node).
A similar shortcoming exists in the generic build_sched_domains() (in
kernel/sched.c) for NUMA, and that needs to be fixed also. The fix
involves dynamically allocating sched_group_nodes[] and
sched_group_allnodes[] for each invocation of build_sched_domains(), rather
than using global arrays for these structures. Care must be taken to
remember kmalloc() addresses so that arch_destroy_sched_domains() can
properly kfree() the new dynamic structures.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When handling writes to /proc/irq, current code is re-programming rte
entries directly. This is not recommended and could potentially cause
chipset's to lockup, or cause missing interrupts.
CONFIG_IRQ_BALANCE does this correctly, where it re-programs only when the
interrupt is pending. The same needs to be done for /proc/irq handling as well.
Otherwise user space irq balancers are really not doing the right thing.
- Changed pending_irq_balance_cpumask to pending_irq_migrate_cpumask for
lack of a generic name.
- added move_irq out of IRQ_BALANCE, and added this same to X86_64
- Added new proc handler for write, so we can do deferred write at irq
handling time.
- Display of /proc/irq/XX/smp_affinity used to display CPU_MASKALL, instead
it now shows only active cpu masks, or exactly what was set.
- Provided a common move_irq implementation, instead of duplicating
when using generic irq framework.
Tested on i386/x86_64 and ia64 with CONFIG_PCI_MSI turned on and off.
Tested UP builds as well.
MSI testing: tbd: I have cards, need to look for a x-over cable, although I
did test an earlier version of this patch. Will test in a couple days.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Zwane Mwaikambo <zwane@holomorphy.com>
Grudgingly-acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Resend using accessors instead of volatile qualifiers per hch comments, and
easier to understand convenience macros per rja comments.
Patch to apply volatile semantics when accessing MMR's in various SN files.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The config option 'CONFIG_ACPI_DEALLOCATE_IRQ' is no longer
needed. This patch removes it.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The reenabling of psr.ic should really belong to dtr mapping code block.
It make the fall through code fast since it doesn't need to execute the
predicated-off instruction. Logically make more sense as well since psr.ic
was turned off in .map code block.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The exception handler in copy user always expects fault occurs only on
user space address and the fall back recovery code is written with that
very assumption in mind. Recent source code inspection revealed that
while it worked splendid and to the expectation under normal circumstances,
It broke down under unexpected condition where some address calculation
might go outside the legal address range the original copy_user was
called for. This patch is to make copy_user exception handler more robust
and to prevent potential memory corruption.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When XPC is being shutdown (i.e., rmmod, reboot) it doesn't ensure that
other partitions with whom it was connected have completely disengaged
from any attempt at cross-partition memory references. This can lead to
MCAs in any of these other partitions when the partition is reset.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When copying data from user-space to kernel-space by __copy_user(),
a page_not_present fault sometimes occurs at vmalloced kernel address
because of VHPT pre-fetching.
Ignore the page_not_present fault in ia64_do_page_fault() before
jumping into exception handlers.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
1) workaround a h/w reset issue
2) to improve the determination of FPGA-based h/w in
the arch/ia64/sn/kernel/tiocx code.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change sn2-specific calls into generic functions. Without this change
the uncached allocator will not work on non-sn2 platforms.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
- notifying the PROM of specific features that are supported by the OS.
This is used to enable PROM feature if and only if the corresponding
feature is implemented in the OS
- fetch feature sets that are supported by the current PROM. This allows
the OS to selectively enable features when the PROM support is available.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I've solved the problem I was having with the simulator and not
booting Debian.
The problem is that the number of bits for the virtual linear array
short-format VHPT (Virtually mapped linear page table, VMLPT for
short) is being tested incorrectly.
There are two problems:
1. The PAL call that should tell the kernel the size of the
virtual address space isn't implemented for the simulator, so
the kernel uses the default 50. This is addressed separately
in dc90e95f31
2. In arch/ia64/mm/init.c there's code to calcualte the size
of the VMLPT based on the number of implemented virtual address
bits and the page size. It checks to see if the VMLPT base
address overlaps the top of the mapped region, but this check
doesn't allow for the address space hole, and in fact will
never trigger.
Here's an alternative test and panic, that I think is more accurate.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Not all of the PAL VM calls are implemented for the SKI simulator.
Don't just give up if one fails, print information from the calls
that succeed.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch implements PAL_VM_SUMMARY (and PAL_MEM_ATTRIB for good
measure) and pretends that the simulated machine is a McKinley.
Some extra comments and clean-up by Tony Luck.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
copy_page.o appeared twice in arch/ia64/lib/Makefile. The
one in global lib-y is wrong where it should be just in
lib-$(CONFIG_ITANIUM).
Both copy_page.o and copy_page_mck.o are build for Itanium2
processor and the link order will pick up the low performing
copy_page function (originally written for itanium processor).
In this case, we really want the copy_page_mck.o for optimized
version.
Signed-off-by: Kenneth Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch to support P-state transitions on ia64. This driver is based on ACPI,
and uses the ACPI processor driver interface to find out the P-state support
information for the processor. This driver plugs into generic cpufreq
infrastructure.
Once this driver is loaded successfully, ondemand/userspace governor can be
used to change the CPU frequency dynamically based on load or on request from
userspace process.
Refer :
ACPI specification -
http://www.acpi.info
P-state related PAL calls -
http://developer.intel.com/design/itanium/downloads/24869909.pdf
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
bte_copy() calls calls smp_processor_id(), which will get flagged if
preemption if enabled. raw_smp_processor_id() is used instead
because we are just using it to pick a BTE interface and are not
tied to a specific cpu.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to abstract irq_affinity down to the pci provider level since
different SGI hardware implements this in different ways.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Delete the ability to build an ACPI kernel that does
not include PCI support. When such a machine is created
and it requires a tuned kernel, send a patch.
http://bugzilla.kernel.org/show_bug.cgi?id=1364
Signed-off-by: Len Brown <len.brown@intel.com>
Build issues were mostly in the ACPI=n case -- don't do that.
Select ACPI from IA64_GENERIC.
Add some missing dependencies on ACPI.
Mark BLACKLIST_YEAR and some laptop-only ACPI drivers
as X86-only. Let me know when you get an IA64 Laptop.
Signed-off-by: Len Brown <len.brown@intel.com>
Clean up of SGI SN partitioning related code.
The SN_SAL_GET_SN_INFO SAL call returns the partition ID, making
the SN_SAL_SYSCTL_PARTITION_GET SAL call redundant. Remove sn_partid
and use sn_partition_id.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the SN pci device info to use the nearest node function
to allocate driver memory on the nearest node (rather than
defaulting to node 0).
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add a new exported function for determining the nearest node
with CPUs for I/O nodes and fix a bug where the hwperf dynamic
misc device was being registered before misc_init().
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Bugfix to export PCI topology information in /proc/sgi_sn/sn_topology.
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently, region numbers are defined in several files, with several
names. For example, we have REGION_KERNEL in asm/page.h and
RGN_KERNEL in pgtable.h
We also have address definitions that should depend on the
RGN_XXX macros, but are currently just long constants.
The following patch reorganises all the definitions so that they have
the same form (RGN_XXX), are in one place, and that addresses that
depend on RGN_XXX are derived from them.
(This is a necessary but not sufficient patch to allow UML-like
operation on IA64).
Thanks to David Mosberger for catching the change I missed in mmu_context.h.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Kernel 2.6 doesn't support egcs, and I didn't find any user of this
function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Removed IA64 architecture specific users of asm/segment.h
The removal of asm-ia64/segment.h itself can wait until all
of the kernel source has been purged of references.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pcibios_bus_to_resource is exported on all architectures except ia64
and sparc. Add exports for the two missing architectures. Needed when
Yenta socket support is compiled as a module.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thanks to Stephane, we've now worked out the real cause of the
`Linux will not boot on simulator' problem. Turns out it's a stack
overflow because the stack pointer wasn't being initialised properly
in boot_head.S (it was being initialised to the lowest instead of the
highest address of the stack, so the first push started to overwrite
data in the BSS).
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix swiotlb sizing to match what the comments and the kernel
parameters documentation indicate. Given a default 16k page size kernel
(ia64) and a 2k swiotlb page size, we're off by a multiple of 8 trying
to size the swiotlb. When specified on the boot line, the swiotlb is
made 8x bigger than requested. When left to the default value, it's 8x
smaller than the comments indicate. For x86_64 the multiplier would be
2x. The patch below fixes this. Now, what's a good default swiotlb
size? Apparently we don't really need 64MB.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
After building a fresh tree with gcc 4 I can't boot the simulator as
the bootloader loader dies with
loading /home/ianw/kerntest/kerncomp//build/sim_defconfig/vmlinux...
failed to read phdr
After some investigation I believe this is do with differences between
the alignment of variables on the stack between gcc 3 and 4 and the
ski simulator. If you trace through with the simulator you can see
that the disk_stat structure value returned from the SSC_WAIT_COMPLETION
call seems to be only half loaded. I guess it doesn't like the alignment
of the input.
Signed-off-by: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Shub2 provides a much improved mechanism for issuing internode
TLB purges. Add code to support the newer mechanism. There is also
some debug code (disabled) that is useful for testing.
Collect statistics on the number, type & duration of TLB purges.
This data will be useful for making future improvements in the algorithms.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change the BTE driver so that it works for both shub1 and
shub2. Most of the changes are related to the number of cores
that use the BTE engine, to the MMR addresses of various
shub registers, and to using the correct processor or network
physical address.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Disable some shub1-specific code when running on systems with shub2.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the addresses of the pio_write_status_addr so that
they are correct for newer processors. Shub2 did not number
the threads in the order that I had expected.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use local SHUB alias space when referencing MMRs that are known
to be node local. There is a slight performance benefit & code
simplification.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Just `make oldconfig' doesn't help for the zx1 defconfig ---
because we need the MPT Fusion drivers, which are picked up as not
selected.
Tested on HP ZX2000 and ZX2600.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The main issue is that bus_fixup calls may potentially call
functions that require a valid bus->sysdata pointer. Since
this is the case, we must set the bus->sysdata pointer before
calling the bus_fixup functions. The remaining changes are
simple fixes to make sure memory is cleaned up in the function.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The current one doesn't even make sense anymore on i386 where it
apparently came from.
Follow-up wordsmithing by Matthew Wilcox and Tony Luck.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to add an SN pci provider for TIOCE, which is SGI's
PCI Express implementation.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to add TIO "huge-window" address support to sn_dma_flush().
Update copyright in affected files.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to abstract the force_interrupt() mechanism away from the
pcibr provider.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cosmetic altix patch to rename SGI_PCIBR_ERROR to something more generic and
remove a duplicate #define.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The PFM_LOAD_CONTEXT may fail silently and cause a session
to remain reserved even though it should not. This can happen
when the commands succeeds in reserving the session but fails
when it actually tries to attach to the load_pid. In that case,
the command has failed but will return 0. More importantly,
the session will remain reserved. This patch fixes the problem.
Signed-off-by: <stephane.eranian@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
this changeset broke the "nohalt" kernel boot option.
8df5a500a3
default_idle() is looking at new variable can_do_pal_halt. However,
that variable did not get cleared upon "nohalt" boot option. Result
is that "nohalt" option is ignored until perfmon is exercised.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
error condition is passed along by acpi_register_gsi().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Current acpi_register_gsi() function has no way to indicate errors to its
callers even though acpi_register_gsi() can fail to register gsi because of
some reasons (out of memory, lack of interrupt vectors, incorrect BIOS, and so
on). As a result, caller of acpi_register_gsi() cannot handle the case that
acpi_register_gsi() fails. I think failure of acpi_register_gsi() should be
handled properly.
This series of patches changes acpi_register_gsi() to return negative value on
error, and also changes callers of acpi_register_gsi() to handle failure of
acpi_register_gsi().
This patch changes the type of return value of acpi_register_gsi() from
"unsigned int" to "int" to indicate an error. If acpi_register_gsi() fails to
register gsi, it returns negative value.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This removes sys_set_zone_reclaim() for now. While i'm sure Martin is
trying to solve a real problem, we must not hard-code an incomplete and
insufficient approach into a syscall, because syscalls are pretty much
for eternity. I am quite strongly convinced that this syscall must not
hit v2.6.13 in its current form.
Firstly, the syscall lacks basic syscall design: e.g. it allows the
global setting of VM policy for unprivileged users. (!) [ Imagine an
Oracle installation and a SAP installation on the same NUMA box fighting
over the 'optimal' setting for this flag. What will they do? Will they
try to set the flag to their own preferred value every second or so? ]
Secondly, it was added based on a single datapoint from Martin:
http://marc.theaimsgroup.com/?l=linux-mm&m=111763597218177&w=2
where Martin characterizes the numbers the following way:
' Run-to-run variability for "make -j" is huge, so these numbers aren't
terribly useful except to see that with reclaim the benchmark still
finishes in a reasonable amount of time. '
in other words: the fundamental problem has likely not been solved, only
a tendential move into the right direction has been observed, and a
handful of numbers were picked out of a set of hugely variable results,
without showing the variability data. How much variance is there
run-to-run?
I'd really suggest to first walk the walk and see what's needed to get
stable & predictable kernel compilation numbers on that NUMA box, before
adding random syscalls to tune a particular aspect of the VM ... which
approach might not even matter once the whole picture has been analyzed
and understood!
The third, most important point is that the syscall exposes VM tuning
internals in a completely unstructured way. What sense does it make to
have a _GLOBAL_ per-node setting for 'should we go to another node for
reclaim'? If then it might make sense to do this per-app, via numalib or
so.
The change is minimalistic in that it doesnt remove the syscall and the
underlying infrastructure changes, only the user-visible changes. We
could perhaps add a CAP_SYS_ADMIN-only sysctl for this hack, a'ka
/proc/sys/vm/swappiness, but even that looks quite counterproductive
when the generic approach is that we are trying to reduce the number of
external factors in the VM balance picture.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
unwind.c can read the wrong unat bits from switch_stack.
sw->caller_unat is the value of ar.unat when the task was blocked.
sw->ar_unat is the value of ar.unat after doing st8.spill for r4-7.
IOW, ar_unat is caller_unat with 4 bits changed.
unw_access_gr() uses sw->ar_unat for r4-7 (correct), but it also uses
sw->ar_unat for other scratch registers (incorrect). sw->ar_unat
should only be used for r4-7, everything else should use
sw->caller_unat, unless modified by unwind info. Using sw->ar_unat
risks picking up the 4 bits that were overwritten when r4-7 were saved.
Also this line is wrong
unw.sw_off[unw.preg_index[UNW_REG_PFS]] = SW(AR_UNAT);
and should be
unw.sw_off[unw.preg_index[UNW_REG_PFS]] = SW(AR_PFS);
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Here's the patch again to fix the code to handle if the values between
MAX_USER_RT_PRIO and MAX_RT_PRIO are different.
Without this patch, an SMP system will crash if the values are
different.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
machine_restart, machine_halt and machine_power_off are machine
specific hooks deep into the reboot logic, that modules
have no business messing with. Usually code should be calling
kernel_restart, kernel_halt, kernel_power_off, or
emergency_restart. So don't export machine_restart,
machine_halt, and machine_power_off so we can catch buggy users.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
XPC calls smp_processor_id() twice from xpc_setup_infrastructure() with
preemption enabled, which gets flagged if 'DEBUG_PREEMPT=y'. This patch
replaces the two calls to smp_processor_id() by a single call to
raw_smp_processor_id() since any CPU within the partition will do.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The Altix subarch does not provide node information via ACPI. Instead hooks
are used to fixup pci structures. This patch determines the nodes for Altix
PCI busses.
Remote Bridges:
---------------
Altix supports remote I/O nodes without memory or processors but with bridges.
The TIOCA type of bridge is an AGP bridge and the PROM provides information
about the closest node. That information will be returned by pcibus_to_node.
The TIOCP remote bridge type is a PCI bridge but the PROM does not provide a
closest node id. pcibus_to_node will return -1 for devices on those bridges
meaning that device control structures may be allocated on any node.
Safeguard:
----------
Should the fixups result in invalid node information for a pci controller then
a warning will be printed and pcibus_to_node will return -1.
This patch also fixes the "FIXME" in sn_dma_alloc_coherent. This means that
dma_alloc_coherent will now use alloc_pages_node to allocate memory local to
the node that the PCI device is connected to.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Check with PAL to see what the i-cache line size is for
each level of the cache, and so use the correct stride
when flushing the cache.
Acked-by: David Mosberger
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the CONFIG_IA64_SGI_SN_SIM option entirely, allowing
any kernel bootable on sn2 to also be booted in the simulator.
Boot tested on Altix and HP rx2600.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pcibus_to_node provides a way for the Linux kernel to identify to which
node a certain pcibus connects to. Allocations of control structures
for devices can then be made on the node where the pci bus is located
to allow local access during interrupt and other device manipulation.
This patch provides a new "node" field in the the pci_controller
structure. The node field will be set based on ACPI information (thanks
to Alex Williamson <alex.williamson@hp.com for that piece).
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ACPI 3.0 added a Correctable Platform Error Interrupt (CPEI)
Processor Overide flag to MADT.Platform_Interrupt_Source.
Record the processor that was provided as hint from ACPI.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Current assign_irq_vector() will panic if interrupt vectors is running
out. But I think how to handle the case of lack of interrupt vectors
should be handled by the caller of this function. For example, some
PCI devices can raise the interrupt signal via both MSI and I/O
APIC. So even if the driver for these device fails to allocate a
vector for MSI, the driver still has a chance to use I/O APIC based
interrupt. But currently there is no chance for these driver to use
I/O APIC based interrupt because kernel will panic when
assign_irq_vector() fails to allocate interrupt vector.
The following patch changes assign_irq_vector() for ia64 to return
-ENOSPC on error instead of panic (as i386 and x86_64 versions do).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Description: Replace schedule_timeout() with msleep_interruptible() to
guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jesse Barnes provided the original version of this patch months ago, but
other changes kept conflicting with it, so it got deferred. Greg Edwards
dug it out of obscurity just over a week ago, and almost immediately
another conflicting patch appeared (Bob Picco's memory-less nodes).
I've resolved the conflicts and got it running again. CONFIG_SGI_TIOCX
is set to "y" in defconfig, which causes a Tiger to not boot (oops in
tiocx_init). But that can be resolved later ... get this in now before it
gets stale again.
Signed-off-by: Tony Luck <tony.luck@intel.com>
I reworked how nodes with only CPUs are treated. The patch below seems
simpler to me and has eliminated the complicated routine
reassign_cpu_only_nodes. There isn't any longer the requirement
to modify ACPI NUMA information which was in large part the
complexity introduced in reassign_cpu_only_nodes.
This patch will produce a different number of nodes. For example,
reassign_cpu_only_nodes would reduce two CPUonly nodes and one memory node
configuration to one memory+CPUs node configuration. This patch
doesn't change the number of nodes which means the user will see three. Two
nodes without memory and one node with all the memory.
While doing this patch, I noticed that early_nr_phys_cpus_node isn't serving
any useful purpose. It is called once in find_pernode_space but the value
isn't used to computer pernode space.
Signed-off-by: bob.picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
restore_sigcontext calls ia64_set_local_fpu_owner() which requires that
preempt be disabled.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is the SGI hotplug driver and additional changes required for
the driver. These modifications include changes to the SN io_init.c code
for memory management, the inclusion of new SAL calls to enable and disable
PCI slots, and a hotplug-style driver.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is a rewrite of the code to check the PROM version. The current
code has some deficiences in the way PROM comparisons were made. The minimum
value of PROM that will boot has also been changed to 4.04.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch moves header files out of the arch/ia64/sn directories and into
include/asm-ia64/sn. These files were being included by other subsystems
and should be under include/asm-ia64/sn.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes the SN IRQ code such that cpu affinity and
Hotplug can modify IRQ values. The sn_irq_info structures are now locked
using a RCU lock mechanism to avoid lock contention in the lost interrupt
WAR code.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following renames arch_init, a kprobes function for performing any
architecture specific initialization, to arch_init_kprobes in order to
cleanup the namespace.
Also, this patch adds arch_init_kprobes to sparc64 to fix the sparc64 kprobes
build from the last return probe patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's another problem shown up by Ingo's recent patch to make
smp_processor_id() complain if it's called with preemption enabled.
local_finish_flush_tlb_mm() calls activate_context() in a situation
where it could be rescheduled to another processor. This patch
disables preemption around the call.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch makes it possible to use the "F4" function key to do
magic sysrq in the HP Ski simulator.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes an ordering issue between the init code for the
tiocx bus driver and tiocx-related device drivers. Also adds
a new brick to the list of known FPGA bricks.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is a sparse compile cleanup of tioca_provider.c, sn_hwperf.h, and
tioca_provider.h. Each of these files had sparse warnings when
compiled.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch changes some macros that are used when running kernel on the
SGI simulator.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is a sparse compile cleanup of shub_mmr.h using both the defconfig
and the sn2_defconfig config files.
The issue with this file was the missing usage of __IA64_UL_CONST wrapper.
This wrapper is defined in include/asm-ia64/types.h and wraps a long
constant definition with UL or with nothing depending on its usage in the
kernel. The missing wrapper caused many sparse compile errors like
warning: constant 0x0x0000000010000380 so big it is long
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch greatly speeds up the handling of lfetch.fault instructions
which result in NaT consumption. Due to the NaT-page mapped at address
0, this is guaranteed to happen when lfetch.fault'ing a NULL pointer.
With this patch in place, we can even define prefetch()/prefetchw() as
lfetch.fault without significant performance degradation. More
importantly, it allows compilers to be more aggressive with using
lfetch.fault on pointers that might be NULL.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
No functional change, just identify the device nicely:
-IOC: Unknown (103c:12ec) 0.1 HPA 0xf8020002000 IOVA space 1024Mb at 0x40000000
+IOC: sx2000 0.1 HPA 0xf8020002000 IOVA space 1024Mb at 0x40000000
We used to create fake PCI devices for these chips, but we no longer do that.
So I don't think there's any reason to touch pci_ids.h now.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to enable use of vgacon driver on that platform. Depends on the
PCDP generalization patch discussed at:
http://marc.theaimsgroup.com/?l=linux-ia64&m=111446235101939&w=2
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Resend 2 with changes per Bjorn Helgaas comments. Changes from original:
+ Change globals to vga_console_iobase/vga_console_membase and make them
unconditional.
+ Address style-related comments.
Patch to extend the PCDP vga setup code to support PCI io/mem translations
for the legacy vga ioport and ram spaces on architectures (e.g. altix) which
need them.
Summary of the changes:
drivers/firmware/pcdp.c
drivers/firmware/pcdp.h
-----------------------
+ add declaration for the spec-defined PCI interface struct (pcdp_if_pci)
as well as support macros.
+ extend setup_vga_console() to know about pcdp_if_pci and add a couple of
globals to hold the io and mem translation offsets if present.
arch/ia64/kernel/setup.c
------------------------
+ tweek early_console_setup() to allow multiple early console setup routines
to be called.
include/asm-ia64/vga.h
----------------------
+ make VGA_MAP_MEM vga_console_membase aware
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is an ia64 implementation of acpi_register_ioapic() and
acpi_unregister_ioapic() interfaces.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the following new interfaces for I/O xAPIC
hotplug. The implementation of these interfaces depends on each
architecture.
o int acpi_register_ioapic(acpi_handle handle, u64 phys_addr,
u32 gsi_base);
This new interface is to add a new I/O xAPIC specified by
phys_addr and gsi_base pair. phys_addr is the physical address
to which the I/O xAPIC is mapped and gsi_base is global system
interrupt base of the I/O xAPIC. acpi_register_ioapic returns
0 on success, or negative value on error.
o int acpi_unregister_ioapic(acpi_handle handle, u32 gsi_base);
This new interface is to remove a I/O xAPIC specified by
gsi_base. acpi_unregister_ioapic returns 0 on success, or
negative value on error.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Read bridge io/mem/pfmem ranges when fixing up the bus so that bus resources
are tracked. This is required to properly support pci end device and bridge
hotplug.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI scan code calls the arch specific pcibios_fixup_bus() each time it scans a
new bridge. For root bridge hot-plug, the bridge and it's attached devices
may not have been configured properly yet, so it's not safe to claim those
resources at this time.
This code goes away when we clean up the way pci resources are claimed (in
pci_enable_device()), so this is only a stopgap fix.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When checking if a PCI to PCI bridge should be enabled to decode memory and/or
IO resources, we need to look at all device resources not just the first 6.
This is needed to allow PCI bridges to pass down memory and IO accesses to
child devices even when the bridge itself does not consume resources in its
PCI BARs.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When you hot-plug a (root) bridge hierarchy, it may have p2p bridges and
devices attached to it that have not been configured by firmware. In this
case, we need to configure the devices before starting them. This patch
separates device start from device scan so that we can introduce the
configuration step in the middle.
I kept the existing semantics for pci_scan_bus() since there are a huge number
of callers to that function.
Also, I have no way of testing the changes I made to the parisc files, so this
needs review by those folks. Sorry for the massive cross-post, this touches
files in many different places.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Not safe to insert kprobes on IVT code.
This patch checks to see if the address on which Kprobes is being inserted is
in ivt code and if it is in ivt code then refuse to register kprobe.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Acked-by: David Mosberger <davidm@napali.hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without the ability to atomically write 16 bytes, we can not update the
middle slot of a bundle, slot 1, unless we stop the machine first. This
patch will ensure the ability to robustly insert and remove a kprobe by
refusing to insert a kprobe on slot 1 until a mechanism is in place to
safely handle this case.
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch implements function return probes for ia64 using
the revised design. With this new design we no longer need to do some
of the odd hacks previous required on the last ia64 return probe port
that I sent out for comments.
Note that this new implementation still does not resolve the problem noted
by Keith Owens where backtrace data is lost after a return probe is hit.
Changes include:
* Addition of kretprobe_trampoline to act as a dummy function for instrumented
functions to return to, and for the return probe infrastructure to place
a kprobe on on, gaining control so that the return probe handler
can be called, and so that the instruction pointer can be moved back
to the original return address.
* Addition of arch_init(), allowing a kprobe to be registered on
kretprobe_trampoline
* Addition of trampoline_probe_handler() which is used as the pre_handler
for the kprobe inserted on kretprobe_implementation. This is the function
that handles the details for calling the return probe handler function
and returning control back at the original return address
* Addition of arch_prepare_kretprobe() which is setup as the pre_handler
for a kprobe registered at the beginning of the target function by
kernel/kprobes.c so that a return probe instance can be setup when
a caller enters the target function. (A return probe instance contains
all the needed information for trampoline_probe_handler to do it's job.)
* Hooks added to the exit path of a task so that we can cleanup any left-over
return probe instances (i.e. if a task dies while inside a targeted function
then the return probe instance was reserved at the beginning of the function
but the function never returns so we need to mark the instance as unused.)
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the CFQ io scheduler to the new time sliced design (cfq
v3). It provides full process fairness, while giving excellent
aggregate system throughput even for many competing processes. It
supports io priorities, either inherited from the cpu nice value or set
directly with the ioprio_get/set syscalls. The latter closely mimic
set/getpriority.
This import is based on my latest from -mm.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia64 changes similar to kernel/sched.c.
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do some basic initial tuning.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dead CPU notifies online CPU that it's dead using cpu_state variable.
After switching to physical cpu hotplug, we forgot setting the variable.
This patch fixes it. Currently only __cpu_die uses it. We changed other
locations for consistency in case others use it.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(The i386 CPU hotplug patch provides infrastructure for some work which Pavel
is doing as well as for ACPI S3 (suspend-to-RAM) work which Li Shaohua
<shaohua.li@intel.com> is doing)
The following provides i386 architecture support for safely unregistering and
registering processors during runtime, updated for the current -mm tree. In
order to avoid dumping cpu hotplug code into kernel/irq/* i dropped the
cpu_online check in do_IRQ() by modifying fixup_irqs(). The difference being
that on cpu offline, fixup_irqs() is called before we clear the cpu from
cpu_online_map and a long delay in order to ensure that we never have any
queued external interrupts on the APICs. There are additional changes to s390
and ppc64 to account for this change.
1) Add CONFIG_HOTPLUG_CPU
2) disable local APIC timer on dead cpus.
3) Disable preempt around irq balancing to prevent CPUs going down.
4) Print irq stats for all possible cpus.
5) Debugging check for interrupts on offline cpus.
6) Hacky fixup_irqs() to redirect irqs when cpus go off/online.
7) play_dead() for offline cpus to spin inside.
8) Handle offline cpus set in flush_tlb_others().
9) Grab lock earlier in smp_call_function() to prevent CPUs going down.
10) Implement __cpu_disable() and __cpu_die().
11) Enable local interrupts in cpu_enable() after fixup_irqs()
12) Don't fiddle with NMI on dead cpu, but leave intact on other cpus.
13) Program IRQ affinity whilst cpu is still in cpu_online_map on offline.
Signed-off-by: Zwane Mwaikambo <zwane@linuxpower.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gcc4 doesn't like volatile casts as lvalues. Make the structure members
volatile instead.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is based on work by Carlos O'Donell and Matthew Wilcox. It
introduces/updates the compat_time_t type and uses it for compat siginfo
structures. I have built this on ppc64 and x86_64.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch includes IA64 architecture specific changes(ported form i386) to
support temporary disarming on reentrancy of probes.
In case of reentrancy we single step without calling user handler.
Signed-of-by: Anil S Keshavamurth <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Once the jprobe instrumented function returns, it executes a jprobe_break
which is a break instruction with __IA64_JPROBE_BREAK value. The current
patch checks for this break value, before assuming that jprobe instrumented
function just completed.
The previous code was not checking for this value and that was a bug.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current kprobes does not yet handle register kprobes on some of the
following kind of instruction which needs to be emulated in a special way.
1) mov r1=ip
2) chk -- Speculation check instruction
This patch attempts to fail register_kprobes() when user tries to insert
kprobes on the above kind of instruction.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current Kprobes when patching the original instruction with the break
instruction tries to retain the original qualifying predicate(qp), however
for cmp.crel.ctype where ctype == unc, which is a special instruction
always needs to be executed irrespective of qp. Hence, if the instruction
we are patching is of this type, then we should not copy the original qp to
the break instruction, this is because we always want the break fault to
happen so that we can emulate the instruction.
This patch is based on the feedback given by David Mosberger
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch_prepare_kprobes() was doing lots of functionality
in just one single function. This patch
attempts to clean up arch_prepare_kprobes() by moving
specific sub task to the following (new)functions
1)valid_kprobe_addr() -->> validate the given kprobe address
2)get_kprobe_inst(slot..)->> Retrives the instruction for a given slot from the bundle
3)prepare_break_inst() -->> Prepares break instruction within the bundle
3a)update_kprobe_inst_flag()-->>Updates the internal flags, required
for proper emulation of the instruction at later
point in time.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug where a kprobe still fires when the instruction is predicated
off. So given the p6=0, and we have an instruction like:
(p6) move loc1=0
we should not be triggering the kprobe. This is handled by carrying over
the qp section of the original instruction into the break instruction.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A cleanup of the ia64 kprobes implementation such that all of the bundle
manipulation logic is concentrated in arch_prepare_kprobe().
With the current design for kprobes, the arch specific code only has a
chance to return failure inside the arch_prepare_kprobe() function.
This patch moves all of the work that was happening in arch_copy_kprobe()
and most of the work that was happening in arch_arm_kprobe() into
arch_prepare_kprobe(). By doing this we can add further robustness checks
in arch_arm_kprobe() and refuse to insert kprobes that will cause problems.
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is required to support kprobe on branch/call instructions.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds IA64 architecture specific JProbes support on top of Kprobes
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is an IA64 arch specific handling of Kprobes
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As many of you know that kprobes exist in the main line kernel for various
architecture including i386, x86_64, ppc64 and sparc64. Attached patches
following this mail are a port of Kprobes and Jprobes for IA64.
I have tesed this patches for kprobes and Jprobes and this seems to work fine.
I have tested this patch by inserting kprobes on various slots and various
templates including various types of branch instructions.
I have also tested this patch using the tool
http://marc.theaimsgroup.com/?l=linux-kernel&m=111657358022586&w=2 and the
kprobes for IA64 works great.
Here is list of TODO things and pathes for the same will appear soon.
1) Support kprobes on "mov r1=ip" type of instruction
2) Support Kprobes and Jprobes to exist on the same address
3) Support Return probes
3) Architecture independent cleanup of kprobes
This patch adds the kdebug die notification mechanism needed by Kprobes.
For break instruction on Branch type slot, imm21 is ignored and value
zero is placed in IIM register, hence we need to handle kprobes
for switch case zero.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Rusty Lynch <Rusty.lynch@intel.com>
From: Rusty Lynch <rusty.lynch@intel.com>
At the point in traps.c where we recieve a break with a zero value, we can
not say if the break was a result of a kprobe or some other debug facility.
This simple patch changes the informational string to a more correct "break
0" value, and applies to the 2.6.12-rc2-mm2 tree with all the kprobes
patches that were just recently included for the next mm cut.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It allows a selectable timer interrupt frequency of 100, 250 and 1000 HZ.
Reducing the timer frequency may have important performance benefits on
large systems.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will at least suppress one prompt that users would have received the
first time they compile with the new DISCONTIG arch option. They'll still
get the "Memory Model" prompt, but 99% of them will have the default work
there.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For all architectures, this just means that you'll see a "Memory Model"
choice in your architecture menu. For those that implement DISCONTIGMEM,
you may eventually want to make your ARCH_DISCONTIGMEM_ENABLE a "def_bool
y" and make your users select DISCONTIGMEM right out of the new choice
menu. The only disadvantage might be if you have some specific things that
you need in your help option to explain something about DISCONTIGMEM.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch effectively eliminates direct use of pgdat->node_mem_map outside
of the DISCONTIG code. On a flat memory system, these fields aren't
currently used, neither are they on a sparsemem system.
There was also a node_mem_map(nid) macro on many architectures. Its use
along with the use of ->node_mem_map itself was not consistent. It has
been removed in favor of two new, more explicit, arch-independent macros:
pgdat_page_nr(pgdat, pagenr)
nid_page_nr(nid, pagenr)
I called them "pgdat" and "nid" because we overload the term "node" to mean
"NUMA node", "DISCONTIG node" or "pg_data_t" in very confusing ways. I
believe the newer names are much clearer.
These macros can be overridden in the sparsemem case with a theoretically
slower operation using node_start_pfn and pfn_to_page(), instead. We could
make this the only behavior if people want, but I don't want to change too
much at once. One thing at a time.
This patch removes more code than it adds.
Compile tested on alpha, alpha discontig, arm, arm-discontig, i386, i386
generic, NUMAQ, Summit, ppc64, ppc64 discontig, and x86_64. Full list
here: http://sr71.net/patches/2.6.12/2.6.12-rc1-mhp2/configs/
Boot tested on NUMAQ, x86 SMP and ppc64 power4/5 LPARs.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin J. Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SGI IOC4 I/O controller chip drivers are currently all configured by
CONFIG_BLK_DEV_SGIIOC4. This is undesirable as not all IOC4 hardware features
are needed by all systems.
This patch adds two configuration variables, CONFIG_SGI_IOC4 for core IOC4
driver support (see patch 1/3 in this series for further explanation) and
CONFIG_SERIAL_SGI_IOC4 to independently enable serial port support.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Acked-by: Pat Gefre <pfg@sgi.com>
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the bits to make the XPC code use the uncached
allocator rather than calling into the mspec driver. It also includes the
mspec.h header which is required to build the XPC modules.
Signed-off-by: Jes Sorensen <jes@wildopensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the ia64 uncached page allocator and the generic
allocator (genalloc). The uncached allocator was formerly part of the SN2
mspec driver but there are several other users of it so it has been split
off from the driver.
The generic allocator can be used by device driver to manage special memory
etc. The generic allocator is based on the allocator from the sym53c8xx_2
driver.
Various users on ia64 needs uncached memory. The SGI SN architecture requires
it for inter-partition communication between partitions within a large NUMA
cluster. The specific user for this is the XPC code. Another application is
large MPI style applications which use it for synchronization, on SN this can
be done using special 'fetchop' operations but it also benefits non SN
hardware which may use regular uncached memory for this purpose. Performance
of doing this through uncached vs cached memory is pretty substantial. This
is handled by the mspec driver which I will push out in a seperate patch.
Rather than creating a specific allocator for just uncached memory I came up
with genalloc which is a generic purpose allocator that can be used by device
drivers and other subsystems as they please. For instance to handle onboard
device memory. It was derived from the sym53c7xx_2 driver's allocator which
is also an example of a potential user (I am refraining from modifying sym2
right now as it seems to have been under fairly heavy development recently).
On ia64 memory has various properties within a granule, ie. it isn't safe to
access memory as uncached within the same granule as currently has memory
accessed in cached mode. The regular system therefore doesn't utilize memory
in the lower granules which is mixed in with device PAL code etc. The
uncached driver walks the EFI memmap and pulls out the spill uncached pages
and sticks them into the uncached pool. Only after these chunks have been
utilized, will it start converting regular cached memory into uncached memory.
Hence the reason for the EFI related code additions.
Signed-off-by: Jes Sorensen <jes@wildopensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of the code in arch/*/mm/hugetlbpage.c is quite similar. This patch
attempts to consolidate a lot of the code across the arch's, putting the
combined version in mm/hugetlb.c. There are a couple of uglyish hacks in
order to covert all the hugepage archs, but the result is a very large
reduction in the total amount of code. It also means things like hugepage
lazy allocation could be implemented in one place, instead of six.
Tested, at least a little, on ppc64, i386 and x86_64.
Notes:
- this patch changes the meaning of set_huge_pte() to be more
analagous to set_pte()
- does SH4 need s special huge_ptep_get_and_clear()??
Acked-by: William Lee Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of the (much simplified) early reclaim. The goal of this
patch is to reclaim some easily-freed pages from a zone before falling back
onto another zone.
One of the major uses of this is NUMA machines. With the default allocator
behavior the allocator would look for memory in another zone, which might be
off-node, before trying to reclaim from the current zone.
This adds a zone tuneable to enable early zone reclaim. It is selected on a
per-zone basis and is turned on/off via syscall.
Adding some extra throttling on the reclaim was also required (patch
4/4). Without the machine would grind to a crawl when doing a "make -j"
kernel build. Even with this patch the System Time is higher on
average, but it seems tolerable. Here are some numbers for kernbench
runs on a 2-node, 4cpu, 8Gig RAM Altix in the "make -j" run:
wall user sys %cpu ctx sw. sleeps
---- ---- --- ---- ------ ------
No patch 1009 1384 847 258 298170 504402
w/patch, no reclaim 880 1376 667 288 254064 396745
w/patch & reclaim 1079 1385 926 252 291625 548873
These numbers are the average of 2 runs of 3 "make -j" runs done right
after system boot. Run-to-run variability for "make -j" is huge, so
these numbers aren't terribly useful except to seee that with reclaim
the benchmark still finishes in a reasonable amount of time.
I also looked at the NUMA hit/miss stats for the "make -j" runs and the
reclaim doesn't make any difference when the machine is thrashing away.
Doing a "make -j8" on a single node that is filled with page cache pages
takes 700 seconds with reclaim turned on and 735 seconds without reclaim
(due to remote memory accesses).
The simple zone_reclaim syscall program is at
http://www.bork.org/~mort/sgi/zone_reclaim.c
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes handling of accesses to ar.rsc via ptrace & restore_sigcontext
[With Thanks to Chris Wright for noticing the restore_sigcontext path]
Signed-off-by: Matthew Chapman <matthewc@hp.com>
Acked-by: David Mosberger <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove "pci=routeirq" option for ia64. This was a workaround
after ACPI IRQ routing was changed from "all at boot for everything
in _PRT" to "do it when the device is enabled" in case there were
drivers that didn't use pci_enable_device().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The nested_dtlb_miss handler currently does not handle fault from
hugetlb address correctly. It walks the page table assuming PAGE_SIZE.
Thus when taking a fault triggered from hugetlb address, it would not
calculate the pgd/pmd/pte address correctly and thus result an incorrect
invocation of ia64_do_page_fault(). In there, kernel will signal SIGBUS
and application dies (The faulting address is perfectly legal and we
have a valid pte for the corresponding user hugetlb address as well).
This patch fix the described kernel bug. Since nested_dtlb_miss is a
rare event and a slow path anyway, I'm making the change without #ifdef
CONFIG_HUGETLB_PAGE for code readability. Tony, please apply.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Allow the SGI simulator (medusa) to work on generic kernels. There is
no inherent dependency on an sn2-specific kernel.
Boot tested on Altix, medusa and HP rx2600.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Refresh arch/ia64/defconfig, as it was getting a bit stale. The only
manual changes I made were:
CONFIG_SCSI_SATA=y needed for some Altix base I/O cards
CONFIG_SCSI_SATA_VITESSE=y
CONFIG_DM_MULTIPATH=m the rest are already modules
CONFIG_FUSION_SPI=y new driver breakout
CONFIG_FUSION_FC=m
CONFIG_SGI_TIOCX=y enable some other SGI drivers
CONFIG_SGI_MBCS=m
CONFIG_AGP_SGI_TIOCA=m
Boot tested on Altix, HP rx2600 and Intel Tiger
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The latest assembler catches this typo. (reported by Jim Wilson).
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
current->blocked will be set to the value of current->thread_info->flags if the
cmpxchg to update thread_info->flags fails. For performance reasons the store into
current->blocked was placed in the cmpxchg loop. However, the cmpxchg overwrites the
register holding the value to be stored. In the rare case of a retry the value of
thread_info->flags will be written into current->blocked.
The fix is to use another register so that the register containing the current->blocked
value is not overwritten.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There've been reports of problems with CONFIG_PREEMPT=y and the high
floating point partition. This is caused by the possibility of preemption
and rescheduling on a different processor while saving or restioirng the
high partition.
The only places where the FPU state is touched are in ptrace, in
switch_to(), and where handling a floating-point exception. In switch_to()
preemption is off. So it's only in trap.c and ptrace.c that we need to
prevent preemption.
Here is a patch that adds commentary to make the conditions clear, and adds
appropriate preempt_{en,dis}able() calls to make it so. In trap.c I use
preempt_enable_no_resched(), as we're about to return to user space where
the preemption flag will be checked anyway.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
break.b does not store the break number in cr.iim, instead it stores 0,
which makes all break.b instructions look like BUG(). Extract the
break number from the instruction itself.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Christian Hildner pointed out that the comment did not match what the
code does in cpu_init() when we set up the default control register.
Patch based on suggestions from Ken Chen.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some bits of the kernel assume that gp always points to valid memory,
in particular PHYSICAL_MODE_ENTER() assumes that both gp and sp are
valid virtual addresses with associated physical pages. The IA64
module loader puts gp well past the end of the module, with no physical
backing. Offsets on gp are still valid, but physical mode addressing
breaks for modules. Ensure that gp always falls within the module
body. Also ensure that gp is 8 byte aligned.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a bug in which shub_1_1_found is not being properly initialized or set,
resulting in the improper setting of sn_hub_info->shub_1_1_found.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This gets rid of an unused variable `error' in sys_ia32.c:sys32_epoll_wait()
Getting rid of this one makes parsing the output of the kernecomp
autobuild easier --- searching for `Error' to find a problem kept
hitting this one, even though it's only a warning.
Signed-off-by: Tony Luck <tony.luck@intel.com>
The attached patch cleans up a compilation warning when ACPI
is turned off (i.e., when compiling for the Ski simulator).
Signed-off-by: Tony Luck <tony.luck@intel.com>
In IA64 kernel, sys_mmap calls do_mmap2 and do_mmap2 returns addr if
len=0, which means the mmap sys call succeeds.
Posix.1 says:
The mmap() function shall fail if:
[EINVAL] The value of len is zero.
Here is a patch to fix it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Acked-by: David Mosberger <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I applied the penultimate version of the perfmon patch, which didn't have
the initialization of the new spinlock that was added.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Charles Spirakis
Some linux customers want to optimize their applications on the latest
hardware but are not yet willing to upgrade to the latest kernel. This
patch provides a way to plug in an alternate, basic, and GPL'ed PMU
subsystem to help with their monitoring needs or for specialty work. It
can also be used in case of serious unexpected bugs in perfmon. Mutual
exclusion between the two subsystems is guaranteed, hence no conflict
can arise from both subsystem being present.
Acked-by: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix convert_to_non_syscall() so it arranges for the kernel to be left
via ia64_leave_kernel() rather than ia64_leave_syscall(). The latter
no longer tolerates being called with pSys=0 and pNonSys=1.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The 2.6 kernel has CPE error thresholding.
This patch lets SAL know of this error handling feature.
The changes are SN specific.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
acpi_request_vector() is called in ia64_mca_init() to get the cpe_vector.
The problem is that acpi_request_vector() looks in platform_intr_list[] to
get the vector, but platform_intr_list[] is not initialized with a valid
vector until later (in sn_setup()). Without a valid vector the code
defaults to polling mode.
This patch moves the call to acpi_request_vector() from ia64_mca_init()
to ia64_mca_late_init(), which is after platform_intr_list[] is initialized.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
convert_to_non_syscall() has the same problem that unwind_to_user()
used to have. Fix it likewise.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
These days <linux/ioctl32.h> handles everything, no need for an asm
header on just two architectures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some time ago, GAS was fixed to bring the .spillpsp directive in line
with the Intel assembler manual (there was some disagreement as to
whether or not there is a built-in 16-byte offset). Unfortunately,
there are two places in the kernel where this directive is used in
handwritten assembly files and those of course relied on the "buggy"
behavior. As a result, when using a "fixed" assembler, the kernel
picks up the UNaT bits from the wrong place (off by 16) and randomly
sets NaT bits on the scratch registers. This can be noticed easily by
looking at a coredump and finding various scratch registers with
unexpected NaT values. The patch below fixes this by using the
.spillsp directive instead, which works correctly no matter what
assembler is in use.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I noticed this typo when trying to compile a kernel which had
CONFIG_HOTPLUG turned off. In that case, __devinit is no longer a
no-op and the compiler then detects a section-conflict. Fix by using
__devinitdata instead of __devinit.
Same patch also submitted by Darren Williams to fix compilation error
using sim_defconfig (which has CONFIG_HOTPLUG=n).
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Darren Williams <dsw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Without this patch, the stack is placed _below_ the current task
structure, which is risky at best.
Tony, I think this patch needs to go into 2.6.12, since it fixes a
real bug. Without it, INIT may case secondary errors, which would be
most unpleasant.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
While looking at code generated by gcc4.0 I noticed some functions still
had frame pointers, even after we stopped ppc64 from defining
CONFIG_FRAME_POINTER. It turns out kernel/Makefile hardwires
-fno-omit-frame-pointer on when compiling schedule.c.
Create CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER and define it on architectures
that dont require frame pointers in sched.c code.
(akpm: blame me for the name)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the p_nodepda and p_subnodepda pointers from the pda_s structure.
And then define a new per-cpu pointer to the nodepda and export it so
that it can be accessed by kernel modules.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
- pfm_context_load(): change return value from EINVAL to EBUSY
when context is already loaded.
- pfm_check_task_state(): pass test if context state is MASKED.
It is safe to give access on PFM_CTX_MASKED because the PMU
state (PMD) is stable and saved in software state.
This helps multiplexing programs such as the example given
in libpfm-3.1.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The pmu_active test is based on the values of PSR.up. THIS IS THE PROBLEM as
it does not take into account the lazy restore logic which is as follow (simplified):
context switch out:
save PMDs
clear psr.up
release ownership
context switch in:
if (ctx->last_cpu == smp_processor_id() && ctx->cpu_activation == cpu_activation) {
set psr.up
return
}
restore PMD
restore PMC
ctx->last_cpu = smp_processor_id();
ctx->activation = ++cpu_activation;
set psr.up
The key here is that on context switch out, we clear psr.up and on context switch in
we check if nobody else used the PMU on that processor since last time we came. In
that case, we assume the PMD/PMC are ours and we simply reactivate.
The Caliper problem is that between the moment we context switch out and the moment we
come back, nobody effectively used the PMU BUT the processor went idle. Normally this
would have no incidence but PAL_HALT does alter the PMU registers. In default_idle(),
the test on psr.up is not strong enough to cover this case and we go into PAL which
trashed the PMU resgisters. When we come back we falsely assume that this is our state
yet it is corrupted. Very nasty indeed.
To avoid the problem it is necessary to forbid going to PAL_HALT as soon as perfmon
installs some valid state in the PMU registers. This happens with an application
attaches a context to a thread or CPU. It is not enough to check the psr/dcr bits.
Hence I propose the attached patch. It adds a callback in process.c to modify the
condition to enter PAL on idle. Basically, now it is conditional to pal_halt=1 AND
perfmon saying it is okay.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Correct a bug where tioca_dma_mapped() is putting tioca dma map structs
on the wrong list.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When SAL calls back into the OS, the OS code is running with preempt
disabled so it cannot call sleeping functions.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jack Steiner uncovered some opportunities for improvement in
the MCA recovery code.
1) Set bsp to save registers on the kernel stack.
2) Disable interrupts while in the MCA recovery code.
3) Change the way the user process is killed, to avoid
a panic in schedule.
Testing shows that these changes make the recovery code much
more reliable with the 2.6.12 kernel.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Attached is a patch against David's audit.17 kernel that adds checks
for the TIF_SYSCALL_AUDIT thread flag to the ia64 system call and
signal handling code paths. The patch enables auditing of system
calls set up via fsys_bubble_down, as well as ensuring that
audit_syscall_exit() is called on return from sigreturn.
Neglecting to check for TIF_SYSCALL_AUDIT at these points results in
incorrect information in audit_context, causing frequent system panics
when system call auditing is enabled on an ia64 system.
I have tested this patch and have seen no problems with it.
[Original patch from Amy Griffis ported to current kernel by David Woodhouse]
From: Amy Griffis <amy.griffis@hp.com>
From: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Andi noted that during normal runtime cpu_idle_map is bounced around a lot,
and occassionally at a higher frequency than the timer interrupt wakeup
which we normally exit pm_idle from. So switch to a percpu variable.
I didn't move things to the slow path because it would involve adding
scheduler code to wakeup the idle thread on the cpus we're waiting for.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following patch fixes a bug in the SGI Altix sn_dma_flush code.
sn_dma_flush is broken in 2.6. The code isn't waiting for the DMA
data to be flushed out of the PIC ASIC. This patch is based off the
linux-ia64-test-2.6.12 tree
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch simplifies a couple places where we search for _PXM
values in ACPI namespace. Thanks,
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following patch ensures that the correct error interrupt handling
routine is initialized. This patch is based on the 2.6.12 ia64 release tree.
Signed-off-by: Colin Ngam <cngam@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch detects the existence of an uncached physical AMO address setup
by EFI's XPBOOT (SGI) and converts it to an uncached virtual AMO address.
Depends on a patch submitted on 23 March 2005 with the subject of:
[PATCH 2/3] SGI Altix cross partition functionality (2nd revision)
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch contains the cross partition pseudo-ethernet driver (XPNET)
functional support module.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch contains the communication module (XPC) for cross partition
communication on a partitioned SGI Altix.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
cg-patch couldn't apply the patch to Makefile, and my dumb script
rushed on and ran cg-commit without this change.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch contains the shim module (XP) which interfaces between the
communication module (XPC) and the functional support modules (like XPNET).
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Another step in the effort to eliminate the SN pda structure.
This patch moves the cnodeid_to_nasid_table field out of the pda,
making it a standalone per-cpu data item, and exports it so it can
be accessed by kernel modules.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Here is a patch to enable the SGI tiocx bus driver to distingush between
FPGA-attached h/w and non-FPGA-attached h/w.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Hi Tony,
This patch against ia64-test-2.6.12 fixes a bug where the tiocx code
was inadvertently un-doing some address modifications done in earlier
fixup code. This patch just removes the offending code.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is a small patch to switch fluch_icache_range() to use fc.i
instead of fc. This would save time on processors which can establish
i-cache coherency without flushing the cache-line out to memory (not
that any current processors do). On existing processors, fc.i behaves
like fc. The only caveat is that very old assemblers may not know
about fc.i yet.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch below fixes 3 trivial typos which are caught by the new
assembler (v2.169.90). Please apply.
[Note: fix to memcpy that was also part of this patch was separately
applied from patches by H.J. and Andreas ... so the delta here only
has the other two fixes. -Tony]
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The current ia64 assembler complains about mismatching .proc/.endp pairs.
(Same patch also sent by H.J. Lu)
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Now that we have MC/MT detection patches in, appended patch allows us to
configure MT scheduler optimizations. For now, we will this option off
by default.
There is some discussion going on lkml about setting up sched-domains
which are absolutely needed (like for example, we shouldn't setup SMT domain
for non MT processors). Once that patch goes in, we can enable this option by
default.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Convert most of the current code that uses _NSIG directly to instead use
valid_signal(). This avoids gcc -W warnings and off-by-one errors.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Attached is a patch against David's audit.17 kernel that adds checks
for the TIF_SYSCALL_AUDIT thread flag to the ia64 system call and
signal handling code paths.The patch enables auditing of system
calls set up via fsys_bubble_down, as well as ensuring that
audit_syscall_exit() is called on return from sigreturn.
Neglecting to check for TIF_SYSCALL_AUDIT at these points results in
incorrect information in audit_context, causing frequent system panics
when system call auditing is enabled on an ia64 system.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We were calling ptrace_notify() after auditing the syscall and arguments,
but the debugger could have _changed_ them before the syscall was actually
invoked. Reorder the calls to fix that.
While we're touching ever call to audit_syscall_entry(), we also make it
take an extra argument: the architecture of the syscall which was made,
because some architectures allow more than one type of syscall.
Also add an explicit success/failure flag to audit_syscall_exit(), for
the benefit of architectures which return that in a condition register
rather than only returning a single register.
Change type of syscall return value to 'long' not 'int'.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Yanmin Zhang pointed out a sequence problem when saving the psr. David
Mosberger provided this patch (which gave up a cycle).
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch switches the srlz.i in ia64_leave_kernel() to srlz.d. As
per architecture manual, the former is needed only to ensure that the
clearing of PSR.IC is seen by the VHPT for subsequent instruction
fetches. However, since the remainder of the code (up to and
including the RFI instruction) is mapped by a pinned TLB entry, there
is no chance of an iTLB miss and we don't care whether or not the VHPT
sees PSR.IC cleared. Since srlz.d is substantially cheaper than
srlz.i, this should shave off a few cycles off the interrupt path
(unverified though; I'm not setup to measure this at the moment).
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch changes comments & formatting only. There is no code
change.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Improvements come from eliminating srlz.i, not scheduling AR/CR-reads
too early (while there are others still pending), scheduling the
backing-store switch as well as possible, splitting the BBB bundle
into a MIB/MBB pair.
Why is it safe to eliminate the srlz.i? Observe
that we used to clear bits ~PSR_PRESERVED_BITS in PSR.L. Since
PSR_PRESERVED_BITS==PSR.{UP,MFL,MFH,PK,DT,PP,SP,RT,IC}, we
ended up clearing PSR.{BE,AC,I,DFL,DFH,DI,DB,SI,TB}. However,
PSR.BE : already is turned off in __kernel_syscall_via_epc()
PSR.AC : don't care (kernel normally turns PSR.AC on)
PSR.I : already turned off by the time fsys_bubble_down gets invoked
PSR.DFL: always 0 (kernel never turns it on)
PSR.DFH: don't care --- kernel never touches f32-f127 on its own
initiative
PSR.DI : always 0 (kernel never turns it on)
PSR.SI : always 0 (kernel never turns it on)
PSR.DB : don't care --- kernel never enables kernel-level breakpoints
PSR.TB : must be 0 already; if it wasn't zero on entry to
__kernel_syscall_via_epc, the branch to fsys_bubble_down
will trigger a taken branch; the taken-trap-handler then
converts the syscall into a break-based system-call.
In other words: all the bits we're clearying are either 0 already or
are don't cares! Thus, we don't have to write PSR.L at all and we
don't have to do a srlz.i either.
Good for another ~20 cycle improvement for EPC-based heavy-weight
syscalls.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Two other very minor changes: use "mov.i" instead of "mov" for reading
ar.pfs (for clarity; doesn't affect the code at all). Also, predicate
the load of r14 for consistency.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Avoid some stalls, which is good for about 2 cycles when invoking a
light-weight handler. When invoking a heavy-weight handler, this
helps by about 7 cycles, with most of the improvement coming from the
improved branch-prediction achieved by splitting the BBB bundle into
two MIB bundles.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch reorganizes break_fault() to optimistically assume that a
system-call is being performed from user-space (which is almost always
the case). If it turns out that (a) we're not being called due to a
system call or (b) we're being called from within the kernel, we fixup
the no-longer-valid assumptions in non_syscall() and .break_fixup(),
respectively.
With this approach, there are 3 major phases:
- Phase 1: Read various control & application registers, in
particular the current task pointer from AR.K6.
- Phase 2: Do all memory loads (load system-call entry,
load current_thread_info()->flags, prefetch
kernel register-backing store) and switch
to kernel register-stack.
- Phase 3: Call ia64_syscall_setup() and invoke
syscall-handler.
Good for 26-30 cycles of improvement on break-based syscall-path.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reschedule code to read ar.bsp as early as possible. To enable this,
don't bother clearing some of the registers when we're returning to
kernel stacks. Also, instead of trying to support the pNonSys case
(which makes no sense), do a bugcheck instead (with break 0). Finally,
remove a clear of r14 which is a left-over from the previous patch.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Using stf8 seemed like a clever idea at the time, but stf8 forces
the cache-line to be invalidated in the L1D (if it happens to be
there already). This patch eliminates a guaranteed L1D cache-miss
and, by itself, is good for a 1-2 cycle improvement for heavy-weight
syscalls.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Why is this a good idea? Clearing b7 to 0 is guaranteed to do us no
good and writing it with __kernel_syscall_via_epc() yields a 6 cycle
improvement _if_ the application performs another EPC-based system-
call without overwriting b7, which is not all that uncommon. Well
worth the minimal cost of 1 bundle of code.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Decreases syscall overhead by approximately 6 cycles.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This by itself is good for a 1-2 cycle speed up. Effect is bigger
when combined with the later patches.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[IA64] fix ia64 Kconfig to allow CONFIG_PM on sn2
This probably should have been fixed when I fixed up the generic build for
discontig+numa machines, but oh well.
CONFIG_PM is allowable for generic builds but not for sn2 builds, which
doesn't make much sense, and in fact breaks the build if recent ACPI bits are
added to the tree. It looks like the only arch that needs to prevent
CONFIG_PM stuff is the ski simulator (though those options could probably use
some cleanup as well), so remove the big conditional and replace it with a
simple test for IA64_HP_SIM instead.
Signed-off-by: Jesse Barnes <jbarnes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
vector sharing patch had a typo ... mismatched spin_lock() with
a spin_unlock_irq(). Fix from Kenji Kaneshige.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Rohit and Suresh changed their mind about the order to print things
in /proc/cpuinfo, but didn't include the change in the version of
the patch they sent to me.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Current ia64 linux cannot handle greater than 184 interrupt sources
because of the lack of vectors. The following patch enables ia64 linux
to handle greater than 184 interrupt sources by allowing the same
vector number to be shared by multiple IOSAPIC's RTEs. The design of
this patch is besed on "Intel(R) Itanium(R) Processor Family Interrupt
Architecture Guide".
Even if you don't have a large I/O system, you can see the behavior of
vector sharing by changing IOSAPIC_LAST_DEVICE_VECTOR to fewer value.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Version 3 - rediffed to apply on top of Ashok's hotplug cpu
patch. /proc/cpuinfo output in step with x86.
This is an updated MC/MT identification patch based on the
previous discussions on list.
Add the Multi-core and Multi-threading detection for IPF.
- Add new core and threading related fields in /proc/cpuinfo.
Physical id
Core id
Thread id
Siblings
- setup the cpu_core_map and cpu_sibling_map appropriately
- Handles Hot plug CPU
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Gordon Jin <gordon.jin@intel.com>
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
memcpy_mck.S::__copy_user breaks in the prefetch code under these conditions :-
* src is unaligned and
* dst is near the end of a page and
* the page after dst is unmapped.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Thanks to Mark for tracking down this one. Users of __copy_from_user_inatomic()
will be sad if we don't handle lfetch faults for the "no_context" case.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch against ia64-test-2.6.12 is needed for forthcoming
Altix chipsets. It renames geoid_any_t to geoid_common_t and
splits the 8bit 'slab' field into two 4bit fields for 'slab'
and 'slot'. Similar changes in the Altix SAL will retain backward
compatibility for old kernels.
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Sadly, I goofed in this syscall-tuning patch:
ChangeSet 1.1966.1.40 2005/01/22 13:31:05 davidm@hpl.hp.com
[IA64] Improve ia64_leave_syscall() for McKinley-type cores.
Optimize ia64_leave_syscall() a bit better for McKinley-type cores.
The patch looks big, but that's mostly due to renaming r16/r17 to r2/r3.
Good for a 13 cycle improvement.
The problem is that the size of the physical stacked registers was
loaded into the wrong register (r3 instead of r17). Since r17 by
coincidence always had the value 1, this had the effect of turning
rse_clear_invalid into a no-op. That poses the risk of leaking kernel
state back to user-land and is hence not acceptable.
The fix below is simple, but unfortunately it costs us about 28 cycles
in syscall overhead. ;-(
Unfortunately, there isn't much we can do about that since those
registers have to be cleared one way or another.
--david
Signed-off-by: Tony Luck <tony.luck@intel.com>
patch 2:
Shub2 BTE recovery code will be implemented in SAL.
Define the SAL interface.
Modify bte_error to call SAL for shub2.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch to disable SGI TIOCA GART TLB prefetching due to hw bug.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes a couple of bugs in the zx1/sx1000 sba_iommu. These are
all pretty low likelihood of hitting. The first problem is a simple off
by one, deep in the sba_alloc_range() error path. Surrounding that was
a lock ordering problem that could have potentially deadlocked with the
order the locks are grabbed in sba_unmap_single(). I moved the resource
locking into sba_search_bitmap() to prevent this. Finally, there's a
potential race between unmapping pdir entries and marking incoming DMA
pages clean. If you see any oddities, please let me know, but I've
tested it pretty thoroughly here. Tony, please apply. Thanks,
BTW, many of the options in this driver not on by default are becoming
more and more broken. I'll be working on some patches to clean them
out, but I wanted to get this bug fix out first.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch introduces using the quicklists for pgd, pmd, and pte levels
by combining the alloc and free functions into a common set of routines.
This greatly simplifies the reading of this header file.
This patch is simple but necessary for large numa configurations.
It simply ensures that only pages from the local node are added to a
cpus quicklist. This prevents the trapping of pages on a remote nodes
quicklist by starting a process, touching a large number of pages to
fill pmd and pte entries, migrating to another node, and then unmapping
or exiting. With those conditions, the pages get trapped and if the
machine has more than 100 nodes of the same size, the calculation of
the pgtable high water mark will be larger than any single node so page
table cache flushing will never occur.
I ran lmbench lat_proc fork and lat_proc exec on a zx1 with and without
this patch and did not notice any change.
On an sn2 machine, there was a slight improvement which is possibly
due to pages from other nodes trapped on the test node before starting
the run. I did not investigate further.
This patch shrinks the quicklist based upon free memory on the node
instead of the high/low water marks. I have written it to enable
preemption periodically and recalculate the amount to shrink every time
we have freed enough pages that the quicklist size should have grown.
I rescan the nodes zones each pass because other processess may be
draining node memory at the same time as we are adding.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch adds the necessary "hook" to allow SGI/SN
machines to perform a system power off upon a
'init 0', 'halt -p', 'poweroff' or 'shutdown -h'.
The "hook" is to set the pm_power_off callback
to ia64_sn_power_down(). pm_power_off is checked
in machine_power_off()/do_poweroff() and, if set, is executed.
ia64_sn_power_down() is a function already present (but not
used currently) in the sn kernel.
ia64_sn_power_down() makes a SAL call to execute the
power off.
Signed-off-by: Aaron J Young <ayoung@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is to provide CX port infrastructure for SGI TIO-based
h/w. Also a 'core services' driver for SGI FPGA-based h/w.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
- make pfm_sysctl a global such that it is possible
to enable/disable debug printk in sampling formats
using PFM_DEBUG.
- remove unused pfm_debug_var variable
- fix a bug in pfm_handle_work where an BUG_ON() could
be triggered. There is a path where pfm_handle_work()
can be called with interrupts enabled, i.e., when
TIF_NEED_RESCHED is set. The fix correct the masking
and unmasking of interrupts in pfm_handle_work() such
that we restore the interrupt mask as it was upon entry.
signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
please accept this patch to the Altix SN platform topology export
interface to support new chipsets and to export PCI topology.
This follows on top of Jack Steiner's patch dated March 1st
("New chipset support for SN platform").
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Recently I noticed that clearing ar.ssd/ar.csd right before srlz.d is
causing significant stalling in the syscall path. The patch below
fixes that by moving the register-writes after srlz.d. On a Madison,
this drops break-based getpid() from 241 to 226 cycles (-15 cycles).
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Detect user space by the unwind frame with predicate PRED_USER_STACK
set, instead of a user space IP. Tighten up the last ditch check for
running off the top of the kernel stack.
Based on a suggestion by David Mosberger, reworked to fit the current
tree. This survives my stress test which used to break 2.6.9 kernels.
Unlike 2.6.11, the stress test now unwinds to the correct point, so
gdb can get the user space registers.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Call cpu_relax() in busy-waiting loops of the ITC-syncing code.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Provide a driver for the altix TIOCA AGP chipset. An agpgart backend will
be provided as a separate patch.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Move a couple of headers out of arch/ia64/sn/include/pci and into
include/asm-ia64/sn.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Provide an abstraction of the altix pci dma runtime layer so that multiple
pci-based bridges can be supported.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is required to support cpu removal for IPF systems. Existing code
just fakes the real offline by keeping it run the idle thread, and polling
for the bit to re-appear in the cpu_state to get out of the idle loop.
For the cpu-offline to work correctly, we need to pass control of this CPU
back to SAL so it can continue in the boot-rendez mode. This gives the
SAL control to not pick this cpu as the monarch processor for global MCA
events, and addition does not wait for this cpu to checkin with SAL
for global MCA events as well. The handoff is implemented as documented in
SAL specification section 3.2.5.1 "OS_BOOT_RENDEZ to SAL return State"
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Found by Alexander Nyberg, improved by Bjorn Helgaas.
- Fix the incorrect argument to sizeof()
- looks like memcpy() code pass was dervived from code that used
copy_from_user(). But in this case we are doing to kernel space
to kernel space copy, so memcpy is the right routine, but it
doesn't return an error code.
Signed-off-by: Arun Sharma <arun.sharma@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64 and ppc64 had hugetlb_free_pgtables functions which were no longer being
called, and it wasn't obvious what to do about them.
The ppc64 case turns out to be easy: the associated tables are noted elsewhere
and freed later, safe to either skip its hugetlb areas or go through the
motions of freeing nothing. Since ia64 does need a special case, restore to
ppc64 the special case of skipping them.
The ia64 hugetlb case has been broken since pgd_addr_end went in, though it
probably appeared to work okay if you just had one such area; in fact it's
been broken much longer if you consider a long munmap spanning from another
region into the hugetlb region.
In the ia64 hugetlb region, more virtual address bits are available than in
the other regions, yet the page tables are structured the same way: the page
at the bottom is larger. Here we need to scale down each addr before passing
it to the standard free_pgd_range. Was about to write a hugely_scaled_down
macro, but found htlbpage_to_page already exists for just this purpose. Fixed
off-by-one in ia64 is_hugepage_only_range.
Uninline free_pgd_range to make it available to ia64. Make sure the
vma-gathering loop in free_pgtables cannot join a hugepage_only_range to any
other (safe to join huges? probably but don't bother).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent woes with some arches needing their own pgd_addr_end macro; and 4-level
clear_page_range regression since 2.6.10's clear_page_tables; and its
long-standing well-known inefficiency in searching throughout the higher-level
page tables for those few entries to clear and free: all can be blamed on
ignoring the list of vmas when we free page tables.
Replace exit_mmap's clear_page_range of the total user address space by
free_pgtables operating on the mm's vma list; unmap_region use it in the same
way, giving floor and ceiling beyond which it may not free tables. This
brings lmbench fork/exec/sh numbers back to 2.6.10 (unless preempt is enabled,
in which case latency fixes spoil unmap_vmas throughput).
Beware: the do_mmap_pgoff driver failure case must now use unmap_region
instead of zap_page_range, since a page table might have been allocated, and
can only be freed while it is touched by some vma.
Move free_pgtables from mmap.c to memory.c, where its lower levels are adapted
from the clear_page_range levels. (Most of free_pgtables' old code was
actually for a non-existent case, prev not properly set up, dating from before
hch gave us split_vma.) Pass mmu_gather** in the public interfaces, since we
might want to add latency lockdrops later; but no attempt to do so yet, going
by vma should itself reduce latency.
But what if is_hugepage_only_range? Those ia64 and ppc64 cases need careful
examination: put that off until a later patch of the series.
What of x86_64's 32bit vdso page __map_syscall32 maps outside any vma?
And the range to sparc64's flush_tlb_pgtables? It's less clear to me now that
we need to do more than is done here - every PMD_SIZE ever occupied will be
flushed, do we really have to flush every PGDIR_SIZE ever partially occupied?
A shame to complicate it unnecessarily.
Special thanks to David Miller for time spent repairing my ceilings.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
