This patch changes 24xx to use new register access, except for clock
framework. Clock framework register access will get updates in the
next patch.
Note that board-*.c files change GPMC (General Purpose Memory Controller)
access to use gpmc_cs_write_reg() instead of accessing the registers
directly. The code also uses gpmc_fck instead of it's parent clock
core_l3_ck for GPMC clock.
The H4 board file also adds h4_init_flash() function, which specify the
flash start and end addresses.
Also note that sleep.S removes some unused registers addresses.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds register access for 34xx power and clock management.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.
Only change USB platform init code to use new register access, other
access will be changed in later patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc clean-up for the mux code and remove some unnecessary
ifdefs. Patch changes debug function so it can be used on
both 24xx and 34xx.
Changes are mostly for omap2, but patch also cleans up some
omap1 and common mux code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove MPU-timer based sched_clock() in favor of the common one based
on 32k sync timer which works across all OMAP1/2/3 platforms.
Using 32k based one also gives a valid sched_clock() very early in the
boot process.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are no longer used and similar conversions are provided
by the clocksource/clockevent code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move now OMAP1-specific timer32k code to mach-omap1 since OMAP2/3 32k
timers are done in gptimer code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 32k timer code is moving to OMAP1 specific dir, move the
32k-based sched_clock() into common code where it is based on the 32k
sync counter and can be used even when using MPU timer.
While moving, change the ticks-to-nsecs conversion to use the helper
functions provided by clocksource.h.
Also removed the unused ticks_to_usec, leaving only ticks_to_nsec.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.
This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.
Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used. Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.) This
is important for sleep/suspend so there is a valid counter during
sleep. Note that the suspend/sleep code needs fixing to check for
overflows of this counter.
In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics. A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap processor specific function depending on system type.
Based on an earlier patch by Klaus Pedersen <klaus.k.pedersen@nokia.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.
This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the GPIO interrupt handling is duplicating some of the work
done by the generic IRQ handlers (handle_edge_irq, handle_level_irq)
such as detecting nesting, handling re-triggers etc. Remove this
duplication and use generic hooks based on IRQ type.
Using generic IRQ handlers ensures correct behavior when using
threaded interrupts introduced by the -rt patch.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clearing was moved to the unmask hook because it is known to run
after the interrupt handler has actually run. Before this patch, if
interrupts are threaded, the clearing/unmasking of level triggered
interrupts would be done before the threaded handler actually ran.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OSK board to use new tps65010 gpiolib support. This
includes moving its LED support from leds-osk to gpio-leds,
giving more trigger options and a net platform code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Start cleaning up GPIO handling for OMAP5912 OSK board:
- Initialize GPIOs using the cross-platform calls, not the old
OMAP-private ones.
- Move touchscreen setup out of ads7846 code into board-specfic
setup code, where it belongs.
This doesn't depend on the patches to update OMAP to use the
gpiolib implementation framework.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes misprints in ITE 8152 interrupt demuxing
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ccoreutils and other have started using fstatat64. Thus, we
need a shim for it if we want to support modern oldabi
userlands (such as Debian/arm/lenny) with EABI kernels.
See http://bugs.debian.org/462677
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix signal return code when enable CONFIG_OABI_COMPAT
Signed-off-by: Janboe Ye <janboe.ye@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the code required to register the F75375 device on the
GLAN Tank.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some bootloaders are disabling write buffer coalescing. Enable it back
under linux.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes the return value of omap_dma_chain_a_transfer
to 0 on success instead of the flag 'start_dma', which wasn't really useful
for anything.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although audio and dsp drivers are not integrated yet,
allow compiling in mailbox and mcbsp to see any build
warnings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO IRQ unmask doesn't actually do anything useful. The problem is
hidden by a separate explicit mass unmask at the end of the chained
bank handler.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_MAX is the number of the last gpio, not the number of gpios. So
the bitmap must provide GPIO_MAX + 1 bits.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct GPIO pin assignment for the LCD power control (PCI)
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definitions of ATAG_CORE and ATAG_CORE_SIZE in head.S to
head-common.S. There is no use of these in head.S itself, but they
are used in head-common.S. When building for the !CONFIG_MMU case
these were not defined when compiling head-nommu.S (which includes
head-common.S).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DNS-323, Kurobox-Pro / Linkstation-Pro, QNAP TS-109/TS-209 and some
other orion-based systems have several bogus memory entries in the tag
table, which causes the system to crash at startup. Ignore them by
resetting the tag ID to 0 in a machine fixup function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows monitoring compile issues with Kautobuild for
other omap1 boards until we have more board specific defconfig
files.
After 2.6.25, we can add a generic config_omap_generic16xx to
compile in support for all 16xx boards and then remove other
boards from OSK defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix some spinlock issues reported by lockdep: since the gpio bank
locks can be aquired in both irq and non-irq contexts, they need
to be consistent about always using the irq-safe variants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Build fix:
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:720: warning: passing argument 2 of 'sysfs_create_file' from incompatible pointer type
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
H2 and H3 were broken on by e27a93a944,
which removed declarations for their tps6501x chips. This resolves
that issue for the H2. (Note that this patch *also* broke the isp1301
support on H2; it presumed a not-yet-merged new-style I2c driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of build warnings and errors in mainline for H3 boards; not
all the H3 updates were correct, it seems like the OMAP1 boards are
not getting proper build testing.
Also, commit e27a93a944 introduced a
regression related to the tps65013 chip.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In mainline, the "old style" I2C registration was only removed for
OMAP2, leading to init-time bugs (regressions) like:
sysfs: duplicate filename 'i2c_omap.1' can not be created
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:424 sysfs_add_one+0x40/0xd4()
Modules linked in:
... deletia ...
[<c0036a38>] (omap_init_i2c+0x0/0x50) from [<c000cea8>] (omap_init_devices+0x10/0x24)
r4:c001e000
[<c000ce98>] (omap_init_devices+0x0/0x24) from [<c0008684>] (do_initcalls+0x78/0x200)
... deletia ...
---[ end trace ca143223eefdc828 ]---
kobject_add_internal failed for i2c_omap.1 with -EEXIST, don't try to register things with the same name in the same directory.
The fix is obvious: remove the old init code, it's no longer needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
