FM radio transmission use a preemphasis/deemphasis scheme to reduce
high-frequency noise. The cx88 audio decoder is supposedly set to no
deemphasis by the current driver.
However, the "no deemphasis" setting doesn't work. On my chip, cx23883, it
produces the same result as the 75 us time constant. Maybe the default
settings on the cx23881 are for 50 us?
Since the deemphasis time constant varies by country, allow setting it via a
module parameter.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Get rid of the "CORE" prefix from cx88 printks. It was only used a few times,
and it makes it look like they're coming from the kernel core or something.
Fix the message, "TV tuner 60 at 0x1fe, Radio tuner -1 at 0x1fe", by adding a
"cx88[0]" prefix to be consistent, and to keep people who grep their dmesg
output for cx88 from missing it. Get rid of the addresses, which are always
wrong. The addresses are always set to -1, but because it's an unsigned 8-bit
value, the left shift converts it to the nonsense address 0x1fe.
In the cx8802 driver, some cut and pasted code prefixed lines with "CORE
cx88[0]:", which has been changed to "cx88[0]/2:" like the other printks from
the cx8802 driver.
Also fix some ugly printks in the cx8802 driver that used __FUNCTION__ for
KERN_INFO and KERN_ERR messages.
The changed printks in cx88-mpeg.c also needed lots of whitespace and
80-column fixes.
A bunch of misc changes in cx88-dvb.c and cx88-video.c to add message levels
or a consistent "cx88[?]/2" or "cx88[?]/0" prefix.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A lot of code in cx88-cards.c was only used by cx88-core.c when the core state
is first allocated and initialized. Moving that task to cx88-cards makes the
driver simpler and the files more self contained.
- Module parameters tuner, radio, card, and latency move to cx88-cards.c
- cx88_boards is made static
- cx88_subids is made static and const
- cx88_bcount is eliminated
- cx88_idcount is eliminated
- cx88_card_list() is made static
- cx88_card_setup_pre_i2c() is made static
- cx88_card_setup() is made static
- cx88_pci_quirks() is moved from cx88-core to cx88-cards
The function argument "char *name" is made const too
- get_ressources() is moved from cx88-core to cx88-cards, and renamed to
cx88_get_resources()
- The code to allocate and initialize the core state struct and the chip is
moved out of cx88-core.c:cx88_get_core() and into a new function in
cx88-cards.c, cx88_core_create(). This makes both functions simpler.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx88 driver state stored the ID of the board type in core->board. Every
time the driver need to get some information about the board configuration, it
uses the board number as an index into board configuration array.
This patch changes it so that the board number is in core->boardnr, and
core->board is a copy of the board configuration information. This allows
access to board information without the extra indirection. e.g.
cx88_boards[core->board].mpeg becomes core->board.mpeg.
This has a number of advantages:
- The code is simpler to write.
- It compiles to be smaller and faster, without needing the extra array lookup
to get at the board information.
- The cx88_boards array no longer needs to be exported to all cx88 modules.
- The boards array can be made const
- It should be possible to avoid keeping the (large) cx88_boards array around
after the module is loaded.
- If module parameters or eeprom info override some board configuration
setting, it's not necessary to modify the boards array, which would
affect all boards of the same type.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An error message for PCI resource allocation failure used the board type
before it was set. Just get rid of the error message, as get_ressources()
[sic] already prints one. Format that error message better, and add the pci
function and subsystem information to better associate the error with what
caused it.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vmux setting is only two bits, but was taking up a whole 32
in the input description struct. By changing it to a two-bit
bitfield, it can fit in what was padding space before and drop
the input size by 4 bytes, from 28 to 24. This drops the board
description struct, which has 9 inputs, from 280 to 244 bytes.
Total driver size decreases by 2108 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner-simple is the only sub-driver that uses last_div, so we
can free up two bytes of memory for all other tuners, by moving
this into tuner-simple's private data area.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some lines later filp->private_data is initialized to dev again.
Since there are some checks that might fail in the mean time
keep the later version.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correctly attribute the origin of the driver to Kazuhiko
Kawakami.
It took some time to get the S-O-B line from the original
tvaudio patch author, but here it is.
Signed-off-by: Kazuhiko Kawakami <kazz-0@mail.goo.ne.jp>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When changing channels the audio has to be muted. This is done
by calling CX2341X_ENC_MUTE_AUDIO and by muted the audio input.
The latter is not necessary and is now removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Audio muting for the tuner input was implemented by stopping the
audio microcontroller and restarting it on unmute. However, it
appears that this method can actually crash the audio firmware.
It's rare and seems to happen with NTSC only.
It has been reimplemented by setting to volume to 0. In addition, the
reporting of the mute state has been improved as well: it used to be
impossible to detect whether the audio was muted by the user or if it
was muted due to the microcontroller trying to detect the audio
standard. This is now clearly stated.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Split Club3D card from Yuan PG600-2, GotView PCI DVD Lite
(different composite input)
- Add AVerTV MCE 116 Plus (M116) card
- Allow Xceive cards to be used without Xceive support
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support to optionally reset the IR and/or the video digitizer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Resetting without reloading the firmware is not enough. Sometimes the
firmware is 'stuck' and needs to be reloaded.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the addition of these ioctls, I'm able to watch TV with a 32-bit version
of tvtime on x86_64.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since videobuf_waiton is called with intr=1, it can return -EINTR and therefore
err may be non-zero. This happens when the system goes into the standby state.
Without the BUG() occurring, there's no problem with standby mode while DVB
is being used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add radio support for the Thomson DTT7612 tuner.
This tuner uses a different 1st intermediate frequency than the other radio
tuners supported (a lot of NTSC radio tuners probably need this change too).
Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for
radio reception. The radio frequency setting code in tuner-simple now uses
this field, instead of a special case select() block for each tuner with radio
support.
The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1
in tuner-types.c.
The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and
fm_gain_normal = 1.
Add some defines for tda9887 bits that control IF setting in radio mode.
Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz
radio IF.
Fix the way tda9887 radio options work. The driver was modifying the default
radio mode config templates based on the TDA9887_XXXX flags. This means that
_all_ tuners would get the same settings. If you had a one tuner than used
TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the
tda9987 driver just checks if tuner mode is radio and then applies the config
settings directly to the data being sent, just like how all the TV mode
settings already work.
The PLL setting math is made a little more accurate.
And a grammar error in a printk is fixed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the advanced debug functions to the radio videodev template. One could
already use them from the video and vbi devices.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After some tedious work with a logic probe and a magnifying glass, I've
determined that GPIO 7 is used to switch between the DTT7612's Sound 4.5 MHz
IF output on pin 12 and the FM 10.7MHz If output on pin 11. GPIO 2 is used to
switch the card's analog sound output from from the analog input connector to
the CX23883's audio DACs.
So, in radio mode GPIO2 = 1 and GPIO7 = 0.
Add some comments about how the HD-3000's GPIOs are connected.
Delete the vmux setting for the radio, as vmux doesn't apply to radio mode.
Also delete the lines setting unused gpio words to zero; it's not necessary as
0 is the default value for uninitialized fields.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the current driver, the field order is global. As soon as it's changed it
takes immediate effect. This is a problem when the video changes order mid
stream. Although it mostly works okay, the video may judder / flicker.
This patch attaches the field order to the frame, so that any buffered frames
will not be displayed until the correct field. In the event that the field
order is changed mid stream, the driver will ensure that the previous frame
is displayed for a minimum of 3 fields. These are the two original fields the
frame should have occupied, plus the one extra since the new frame still has
to wait for the correct field.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The yuv output code always compares the new frame position & size with those
of the previous frame. If they are different, a flag is set to request the
yuv output registers be updated when the new frame is displayed.
If the incoming frames are delivered too fast, exhausting the buffers, the
most recent frame already buffered will be discarded. Unfortunately, any
update request will also be discarded. If the new frame matches the size &
position of the now discarded frame, the yuv registers are not flagged for
update & will remain in their old state.
This patch preserves the register update flag in the event that a frame is
dropped.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Framebuffer timings are currently locked to the video format in use when the
module is loaded. If the video format is then changed, the timings returned
by the framebuffer will be for the original format.
This patch ensures that the timings returned reflect the current video format.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the video standard is changed, there's no guarantee the framebuffer
dimensions are still legal. The yuv output code uses these dimensions to
calculate the size & position for the video overlay. If the framebuffer
dimensions are now illegal, the output may exceed the vertical limit of the
display, causing distortion.
This patch adds an additional check to ensure the output doesn't exceed
the limits for the current video standard, cropping if required.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This device is internal to the Panasonic VP27S tuner and is used to set
the mono/stereo/bilingual setting of the tuner.
It is used by two Japanese cx23416-based cards.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The firmware is now loaded when the driver is actually used for the first
time. This allows the driver to be compiled in-kernel instead of as a module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up duplicate includes in
drivers/media/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the ivtv-fb framebuffer driver for cx23415 devices (currently
only the Hauppauge PVR-350 cards). This makes it possible to use
the On-Screen Display functionality of these cards, either for menus
during MPEG playback, or as a console or X display.
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: John P Harvey <john.p.harvey@btinternet.com>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add permissions to all the module parameters so they can be queried and set
(when possible) via sysfs.
Add description for the vidmem parameter.
Change the video_nr parameter to an array, so that the video number can be
specified when a user has more than one card. The driver would try to give
all cards the same number otherwise, which will fail for all cards after the
first.
The default_input option would only allow values of 0 or 1, contrary to the
description. Allow values up to the number of inputs defined for the card.
Add description of lock_norm's different behavior for 1 and >1.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Debugging cleanups to the zr36067 driver:
* Use module_param_named() to declare the debug parameter, so we can
use a single global variable to handle the debug level. This makes
the driver a bit smaller (by 648 bytes on x86_64), thanks to one
less level of indirection on every use.
* Change the debug parameter sysfs permissions, so that the debug
level can be adjusted at runtime, as is done in many other
media/video drivers.
* The debug level is between 0 and 5, not 0 and 4.
* Move the zr_debug export and dprintk macro definition to a header
file so that we don't have to define them in each source file.
* Simplify a duplicate test on zr_debug.
Note that zr_debug was subsequently renamed to debug_zr36067 to avoid
possible conflicts with other Zoran device drivers, on a suggestion
by Trent Piepho.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a compile warning on non-32-bit machines in v4l2-int-device.h.
Add internal ioctl interface fallback function for ioctls with one
argument.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
