Current driver forming a unit test command within HDD layer and uses
message passing method to deliver it to WMA layer which
requires HDD layer to have a knowledge of how to form a unit test command.
User SME API to send params to WMA layer and let WMA form a unit test
command and send it directly to FW through WMI layer instead of HDD
forming and passing it down.
CRs-Fixed: 2118725
Change-Id: Id1838939813e6cd2d52cee8720a1f4e0ca34329b
In case of FILS connection, form 802.3 packet out of
HLP IE info parsed from assoc response(if present) and
send the same to IP layer.
Change-Id: I0e077ee48030da84bfe9f987722f96ac2e05ae36
CRs-Fixed: 2034452
This change adds support to append/store the HLP IE(if present)
in req_ie as part of connect request from Supplicant and adds the
same in Association request for FILS connection.
Change-Id: I8cd3e28b462a8ac2bd9eee2a383f9d0886adfa83
CRs-Fixed: 2034452
Add support to post data stall event to sys message queue
to handle it in data detection module and finally post
diag event to QXDM. Add support to send NUD failure
diag event.
CRs-Fixed: 2086176
Change-Id: I72ba36d4c2f6ef2eb495ad1586f74af0f3c69254
If Probe resp is received just after the Probe after
HB timer expires then it results in disconnection.
Fix is to increase the probe after hb timer default
value to 70msecs.
Change-Id: I0d4ac3e567def348c6b03b41c54579f332099de8
CRs-Fixed: 2111579
Check the length of the IE's before appending them
and storing them in the session in
lim_process_update_add_ies.
Change-Id: I70d26638a58998c82a8810d7c2181d1f24c56e19
CRs-Fixed: 2119729
Some vendor APs are not able to handle the SMPS frames causing the
APs to crash.
Add new check for a vendor AP OUIs and AP being in 4x4 or 3x3 11ac
capabilities to associate in 1x1 to that AP.
Change-Id: I023237fd3531529648890c9d71101b57a036cc7f
CRs-Fixed: 2112017
Currently, while parinsg RSNIE host allow up to 4 max
cipher / akm suits. Hence if beacon / probe response
carry more than 4 cipher/akm suits then RSNIE parsing
get fails.
As a part of fix, increase cipher/akm max count to 6.
Change-Id: I62f8797b480f0cc82586f76ec7fd318499bc7628
CRs-Fixed: 2081030
Enable support for multiple NAN data path peers from host.
FW already supports multiple NAN peers.
CRs-Fixed: 2121121
Change-Id: I23307c5f56114084a93b3afae0e23a07251c5013
Presently, host driver is sending the exit power save
configuration request to firmware when an interface up comes
before iface_change_timer which is not required because firmware
is the master and decides to enter/exit imps.
To mitigate the issue, don't send the exit IMPS request to firmware
before interface change timer expires and re-configure the same
incase of loadonce-unload never in case of firmware is de-initialzied.
Change-Id: Ia47687cdcfc5a5fb7be1a8066e163c3248305bba
CRs-Fixed: 2002110
Change-id Iafd5666179d079c7bcc950277092cef3046356bf was added to remove
antenna sharing support from SAP and STA case but customer needs those
changes for SAP case only.
So bringing back changes for STA case.
CRs-Fixed: 2117829
Change-Id: I79f7c5ae1fd642f0b26170f066a5409638cdd873
While DUT is in SAP or GO mode, due to LTE antenna sharing mechanism,
DUT is associating in 2x1 chains to HT clients.
As per new requirement, remove dependency of number of chains on antenna
sharing. If HT client supports 2 chains, and due to DBS/LTE antenna
sharing SAP/GO drops down a chain then rate adaptation at peer takes
care of dropping down chains at peer side
Change-Id: Iafd5666179d079c7bcc950277092cef3046356bf
CRs-Fixed: 2108484
