This patch updates the Xilinx ML507 device tree to match the released
ML507 powerpc reference design (ml507_ppc440_emb_ref). This patch is
needed to boot Linux on the ML507 powerpc reference design without
manually generating and tweaking a device tree from the project directory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On digsy MTC PSC4 and PSC5 should be configured as UART, not PSC3 and PSC4.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Board support for the InterControl Digsy-MTC device based on the MPC5200B SoC.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds board support for the Media5200 platform. Changes are:
- add the media5200 device tree
- add the media5200 platform support code and cascaded interrupt controller
- add media5200 to the build targets.
Note: this patch also includes a minor tweak to the lite5200(b) target
images list to add the .dtb files to the image list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Trim out obsolete/extraneous properties and tighten up some usage
conventions. Changes include:
- removal of device_type properties
- removal of cell-index properties
- Addition of gpio-controller and #gpio-cells properties to gpio
nodes
- Move common interrupt-parent property out of device nodes and
into top level parent node.
This patch also include what looks to be just trivial editorial
whitespace/format changes, but there is real method in this
madness. Editorial changes were made to keep the all the
mpc5200 board device trees as similar as possible so that diffs
between them only show the real differences between the boards.
The pcm030 device tree was most affected by this because many
of the comments had been changed from // to /* */ style and
some cell values where changed from decimal to hex format when
it was cloned from one of the other 5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert the Warp platform to use the newly merged NDFC driver
- warp.dts changed to work with ndfc
- warp-nand.c no longer needed
- removed obsolete rev A support from cuboot-warp.c
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added additional information for type and compatibility strings and
interrupt information to the SDRAM0 memory-controller device tree
nodes for AMCC PowerPC 405EX[r]-based boards to facilitate binding
with the new "ibm,sdram-4xx-ddr2" EDAC memory controller adapter driver.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
FSL U-Boots use /soc8315@e0000000 node to search and fixup serial
nodes' clock-frequency properties. Though in upstream kernels we use
new naming convention -- for IMMR address space dts files specify
/immr@e0000000 nodes.
This makes FSL U-Boots fail to fixup the clock frequencies, and that
leads to serial ports misbehaviour. We can workaround the issue by
filling the clock frequency values manually.
p.s. For the same reason FSL U-Boots fail to fixup MAC addresses for
ethernet nodes, so users should either change the .dts file locally
or set MAC address via `ifconfig hw ether' command.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the FPGA based watchdog timer on GE Fanuc's SBC610.
This patch enables one of the watchdog timers found on the SBC610. There are
two identical watchdog timers at different offsets in the above mentioned
boards, however the current driver is only capable of supporting one of them.
The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The newest revision of uboot reworks the memory map for this
board to look more like the 85xx boards. Also, some regions
which were far larger than the actual hardware have been scaled
back to match the board, and the imaginary second flash bank has
been removed. Rapidio and PCI are mutually exclusive in the hardware,
and they now are occupying the same space in the address map.
The Rapidio node is commented out of the .dts since PCI is the
common use case.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add the usb node to support USB host on the MPC8360E-RDK
boards.
Currently U-Boot doesn't fill the clock-frequency property for
timer nodes, so for now we have to fill it manually.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.
The work is loosely based on Li Yang's patch[1], which was used
to support peripheral mode only.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html
The s-o-b line of the original patch preserved here.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the localbus reg & range properties to respect that the top
level #address-cells and #size-cells = 2. The original commit
(c64ef80b51) did not do that.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this patch the L2 cache is enabled on Canyonlands to increase the
overall performance. There is a known cache coherency issue with the L2
cache, but this is related to the high bandwidth (HB) PLB segment where
the memory address is 0x8.xxxx.xxxx (low bandwidth PLB segment is mapped
to 0x0.xxxx.xxxx). Since this HB address is currently unused it is safe
to enable the L2 cache.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch creates the dts files for each core and splits the devices
between the two cores for MPC8572DS.
core0 has memory, L2, i2c, dma1, global-util, eth0, eth1, crypto, pci0, pci1.
core1 has L2, dma2, eth2, eth3, pci2, msi.
MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add NOR and NAND flash partitions for mpc8572ds board
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic support for the GPIO available on the SBC610 VPX Single Board Computer
from GE Fanuc (PowerPC MPC8641D).
This patch adds basic support for the GPIO in the devices I/O FPGA, the GPIO
functionality is exposed through the AFIX pins on the backplane, unless used
by an AFIX card.
This code currently does not support switching between totem-pole and
open-drain outputs (when used as outputs, GPIOs default to totem-pole).
The interrupt capabilites of the GPIO lines is also not currently supported.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding use of newly added Epson RTX-8581 real-time clock driver to GE
Fanuc SBC610's dts file and adding driver to default config.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Just found the merge issue in 442746989d
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.
The original patch[1] was OK though. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and
ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so
that the interfaces do not swap addresses when control passes from
U-Boot to the kernel.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no
reason to have the wrong value in the dts.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch corrects the bus-frequency value provided in the SBC610's dts.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't want to encourage the device_type usage. It isn't used in
the code, so we can simply remove it from the dts files.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT2 interrupt line, the line is shared with
Vitesse 8201 Ethernet PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to
provide soft power-off function, but also exports two GPIOs (wired to
the LEDs and also available from the external headers).
Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the top-level #address-cells and #size-cells to <2> so the
mpc8572ds.dts is easier to deal with both a true 32-bit physical
or 36-bit physical address space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't want to encourage the bogus device_type usage.
The device type isn't used in the code, so we can simply remove it from
the documentation and dts files.
Boards should specify proper compatible entries instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds support for a HCU4 PPC405GPr based board from Netstal Maschinen AG.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board.
In addition to some of the normal PPC 40x peripherals, the Acadia
board has:
- 64 MiB PSRAM
- NOR and NAND flash
- Two USB 1.1 host ports
- Two CAN 2.0 ports
- ADC and DAC connectors
- LCD display
This adds the basic platform support to build from.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The StMicro NAND chip (512Mbit, 64MB) is connected to the local bus,
the first local bus' user-programmable machine is configured by the
firmware to work with NAND chips.
QE GPIO pin is used to poll the NAND's Ready-Not-Busy signal.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
