I had trouble connecting my cell phone as a storage device - so I added
it to the unusual_devs.h list. I had trouble with the bcdDeviceMin and
Max values - so after some experimenting I made it pretty inclusive.
From: Filip Joelsson <filip@blueturtle.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This resolves another regression caused by the "use omap_read/write
instead of __REG" patch: the hardware address used for DMA to/from
the UDC became wrong. Bug noted by Russell King.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit de85422b94, 'USB: fix interrupt
disabling for HCDs with shared interrupt handlers' changed usb_add_hcd()
to strip IRQF_DISABLED from irqflags prior to calling request_irq()
with the justification that such a removal was necessary for shared
interrupts to work properly. Unfortunately, the change in that commit
unconditionally removes the IRQF_DISABLED flag, causing problems on
platforms that don't use a shared interrupt but require IRQF_DISABLED.
This change adds a check for IRQF_SHARED prior to removing the
IRQF_DISABLED flag.
Fixes the PS3 system startup hang reported with recent Fedora and
OpenSUSE kernels.
Note that this problem is hidden when CONFIG_LOCKDEP=y (ps3_defconfig),
as local_irq_enable_in_hardirq() is defined as a null statement for
that config.
CC: stable <stable@kernel.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Stefan Becker <Stefan.Becker@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was trying to figure out why my device wasn't supported by the
drivers/usb/serial/sierra.c driver, while looking throught the device
IDs I spotted what I believe to be a typo in the device IDs. Please
apply the following patch
If you look down further, there is another HP wireless broadband card,
which has a vendor ID of 03f0, like my device. Below is my "lsusb -v
-d 03f0:1b1d".
Bus 001 Device 005: ID 03f0:1b1d Hewlett-Packard
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x03f0 Hewlett-Packard
idProduct 0x1b1d
bcdDevice 0.01
iManufacturer 1 HP
iProduct 2 HP ev2200 1xEV-DO Broadband Wireless Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 7
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 3 Data Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 128
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
From: Tony Murray <murraytony@gmail.com>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that the "Refactor "if (handshake()) state = HC_STATE_HALT"
patch from earlier this year perpetuated a potential problem: it can
mark the controller as halted when it's still running (but not acting
as, perhaps wrongly, expected).
That caused some hangs and crashes, rather than more polite failure
modes of a truly halted controller. This patch forces a true halt,
and emits a (previously missing) diagnostic.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds devices to the sierra driver and rev's the driver version.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch alters the Sierra Mass Storage patch so that it is non-configurable.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hw interface drivers for the usb serial devices deference the tty
structure to set up the parameters for the initial console. The tty
structure should be passed as a parameter to the set_termios() call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/usb/host/ohci-omap.c: In function 'ohci_omap_init':
drivers/usb/host/ohci-omap.c:228: error: 'start_hnp' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
usb 1-2: new high speed USB device using ehci_hcd and address 4
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: USB2VGA dongle found at address 4
usb 1-2: Allocated 8 output buffers
usb 1-2: 8MB 1 ch/1 r SDR SDRAM, bus width 32
usb 1-2: New USB device found, idVendor=0711, idProduct=0918
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Signed-off-by: Stefan Lippers-Hollmann <s.L-H@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1130) fixes an incompatibility between the new PM
infrastructure and USB power management. We are not allowed to call
drivers' probe routines during a system sleep transition between the
"prepare" and "complete" callbacks, but that's exactly what we do when
a driver doesn't have full suspend/resume support. Such drivers are
unbound during the "suspend" call and reprobed during the "resume" call.
The patch causes the reprobe step to be skipped if the "complete"
callback hasn't been issued yet, i.e., if the interface's
dev.power.status field is not equal to DPM_ON. Thus during the
"resume" callback nothing bad will happen, and during the final
"complete" callback the reprobing will occur as desired.
This fixes the problem reported in Bugzilla #11263.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1129) adds support for the new PM callbacks to usbcore.
The new callbacks merely invoke the same old USB power management
routines as the old ones did.
A minor improvement is that the callbacks are present only in the
"USB-device" device_type structure, rather than in the bus_type
structure. This way they will be invoked only for USB devices, not
for USB interfaces. The core USB PM routines automatically handle
suspending and resuming interfaces along with their devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1128) fixes one of the problems related to the new PM
infrastructure. We are not allowed to register new child devices
during the middle of a system sleep transition, but unbinding a USB
driver causes the core to automatically install altsetting 0 and
thereby create new endpoint pseudo-devices.
The patch fixes this problem (and the related problem that installing
altsetting 0 will fail if the device is suspended) by deferring the
Set-Interface call until some later time when it is legal and can
succeed. Possible later times are: when a new driver is being probed
for the interface, and when the interface is being resumed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1127) makes a minor change to the prototypes of the
usb_suspend_interface() and usb_resume_interface() routines. Now the
usb_device structure is passed as an argument, instead of being
computed on-the-fly from the usb_interface argument.
It makes the code look simpler, even if it really isn't much different
from before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If Indexed Mode register accesses are enabled, the ep0_rxstate()
function calls musb_g_ep0_giveback() before writing to the CSR
register. When control returns to this ep0_rxstate, the index
register contents are over-written. This causes the CSR register
write to fail.
Fixed by writing the correct value into the index register before
writing to the CSR.
This was observed only in ep0_rxstate() with g_ether loaded and
the device connected to a MS Windows host PC. Anticipatively fixed
ep0_txstate() as well.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can change debugging level on the fly via
/sys/module/musb_hdrc/parameters/debug.
We can also get rid of the LOGLEVEL facility in Kconfig
and rely only in module parameter.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should not add procfs. The functionality in the old
procfs file will be moved to debugfs.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new composite framework revealed a weakness in the
pxa27x_udc driver gadget register function. Instead of
checking if speed asked for was USB_LOW_SPEED upon
usb_gadget_register() to deny service, it checked only
for USB_FULL_SPEED, thus denying service to usb high
speed capable gadgets (like g_ether).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch gets my Rosewill RNX-56USB USB modem (with Conexant CX93010
chipset) up and running to the point where I can send AT commands and
retrieve caller ID data, which is all I want to do with it.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Irqs must not accidentally be reenabled.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch support NTT DoCoMo A2502 3G/HSDPA modem on option driver.
It is produced by AnyDATA Corp. and also sold as KT Freetelecom (Korea) ADU 620UW.
It support 3.6Mbps/7.2Mbps hight speed communication.
I have tested A2502 with NTT DoCoMo MoperaU ISP service.
Signed-off-by: Hiroshi Miura <miurahr@nttdata.co.jp>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we try to modprobe a second gadget driver before
rmmoding the first one, the reference for the first
gadget driver would get NULLed avoiding usb to change
gadget drivers later.
Cc: David Brownell <david-b@pacbell.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These drivers should not be relying on CONFIG_USB_DEBUG. By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.
PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a mechanism to let the write queue drain naturally before
closing the TTY, rather than always losing that data. There
is a timeout, so it can't wait too long.
Provide missing locking inside acm_wb_is_avail(); it matters
more now. Note, this presumes an earlier patch was applied,
removing a call to this routine where the lock was held.
Slightly improved diagnostics on write URB completion, so we
can tell when a write URB gets killed and, if so, how much
data it wrote first ... and so that I/O path is normally
silent (and can't much change timings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "increase cdc-acm write throughput" patch left in place two
now-obsolete mechanisms, either of which can make the cdc-acm
driver drop TX data (nasty!). This patch removes them:
- The write_ready flag ... if an URB and buffer were found,
they can (and should!) always be used.
- TX path acm_wb_is_used() ... used when the buffer was just
allocated, so that check is pointless.
Also fix a won't-yet-matter leak of a write buffer on a disconnect path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Engraf <david.engraf@netcom.eu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bugfixes to the usb_driver_release_interface() usage;
(a) make sure releasing *either* interface first will release
the other, instead of insisting it be the control interface;
(b) remove the recently-added self-deadlock.
(The "fix disconnect bug in cdc-acm" patch was incomplete and incorrect.)
Plus a small "sparse" fix: rename a local variable so it doesn't
shadow a function parameter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the CDC-ACM gadget code to support the peripheral-to-host
notifications when the tty is opened or closed, or issues a BREAK.
The serial framework code calls new generic hooks; right now only
CDC-ACM uses those hooks. This resolves several REVISIT comments
in the code. (Based on a patch from Felipe Balbi.)
Note that this doesn't expose USB_CDC_CAP_BRK to the host, since
this code still rejects USB_CDC_REQ_SEND_BREAK control requests
for host-to-peripheral BREAK signaling (received via /dev/ttyGS*).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes some unused members from the various USB functions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the regression in commit 29fab0cd89
that this driver executed reconnection processing when disconnected
some devices.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1123b) fixes a compiler warning: do_unbind_rebind() is
defined but not used if CONFIG_PM=n.
Problem originally found and initial patch submitted by Alexander
Beregalov <a.beregalov@gmail.com>.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1120) adds an unusual_devs entry for the Nokia 5300.
Maybe once Nokia releases the Symbian code we'll be able to fix all
the problems it has with the USB mass-storage protocol.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Cedric Godin <cedric@belbone.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The irq flags should be unsigned long.
CC [M] drivers/usb/class/cdc-acm.o
drivers/usb/class/cdc-acm.c: In function 'acm_waker':
drivers/usb/class/cdc-acm.c:527: warning: comparison of distinct pointer types lacks a cast
drivers/usb/class/cdc-acm.c:529: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the Product ID for the BandLuxe C150/C250 3.5G data
card series from BandRich Inc.
After detection, the data card works fine.
It was patched against kernel 2.6.27-rc1 with -mm patch
Signed-off-by: Leon Leong <upleong@bandrich.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.
Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: Lex V. Ross <lross@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to Alan Stern, short packets are quite normal under
certain circumstances. This printk was triggered by usb to
serial converters on every packet and some usb sticks triggered
a few of those while plugging the stick.
This printks are now hidden unless USB debug mode is activated.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ISP1760 requires a delay of 90ns between programming the address and
reading the data. Current driver solves this by a mdelay(1) which is
very heavy weighted and slow. This patch applies the workaround from
the ISP1760 FAQ by using two different banks for PTD and payload data
and using a common wait for them. This wait is done by an additional
ISP1760 access (whose timing constraints guarantee the 90ns delay).
This improves speed when reading from an USB stick from:
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 1m 15.43s
user 0m 0.44s
sys 0m 39.46s
to
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 0m 18.53s
user 0m 0.16s
sys 0m 12.97s
[bigeasy@linutronix.de: fixed comment formating, moved define into
header file, obey 80 char rule]
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if the enqueue function returns -ESHUTDOWN or -ENOMEM then
we return 0 instead of an error. This leads to a timeout and
then to a dequeue request of an not enqueued urb.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update RX path handling in new serial gadget code to cope better with
RX blockage: queue every RX packet until its contents can safely be
passed up to the ldisc. Most of the RX path work is now done in the
RX tasklet, instead of just the final "push to ldisc" step. This
addresses some cases of data loss:
- A longstanding serial gadget bug: when tty_insert_flip_string()
didn't copy the entire buffer, the rest of the characters were
dropped! Now that packet stays queued until the rest of its data
is pushed to the ldisc.
- Another longstanding issue: in the unlikely case that an RX
transfer returns data and also reports a fault, that data is
no longer discarded.
- In the recently added RX throttling logic: it needs to stop
pushing data into the TTY layer, instead of just not submitting
new USB read requests. When the TTY is throttled long enough,
backpressure will eventually make the OUT endpoint NAK.
Also: an #ifdef is removed (no longer necessary); and start switching
to a better convention for debug messages (prefix them with tty name).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
