This should bits from -mm tree that are affected by pm_message_t
conversion. [I'm not 100% sure I got all of them, but I certainly got all
the errors on make allyesconfig build, and most of warnings, too. I'll go
through the buildlog tommorow and fix any remaining bits].
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
local->hw_priv was initialized only after the interrupt handler was
registered. This could trigger a NULL pointer dereference in
prism2_pccard_card_present() that assumed that local->hw_priv is always
set (and it should have been). Fix this by setting local->hw_priv before
registering the interrupt handler.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
With my Buffalo WLI-CF-S11G PC Card kernel oopses every time in
prism2_interrupt() when I try load the hostap module. local->hw_priv is null
during the first call to prism2_interrupt(). It feels like
interrupts are enabled too early, or something.
This patch fixes the symptom, but not the cause.
Signed-off-by: Kalle Valo <Kalle.Valo@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_cs: 0.4.1-kernel (Jouni Malinen <jkmaline@cc.hut.fi>)
pcmcia: hostap_cs: invalid hash for product string "BUFFALO": is 0x1b01a57b,
should be 0x2decece3
pcmcia: see Documentation/pcmcia/devicetable.txt for details
pcmcia: hostap_cs: invalid hash for product string "WLI-CF-S11G": is
0xefd5102a, should be 0x82067c18
pcmcia: see Documentation/pcmcia/devicetable.txt for details
This patch fixes them.
Signed-off-by: Kalle Valo <Kalle.Valo@iki.fi>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Version 0.4.4 of Host AP driver was released, so let's sync the version
number in netdev-2.6 tree.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Gertjan van Wingerde <gwingerde@home.nl>
Attached patch updates the definitions of the generic ieee80211 stack to
the latest versions of the published 802.11x specification suite.
Signed-off-by: Gertjan van Wingerde <gwingerde@home.nl>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
This removes one trap for a programmer, few unused macros, and one
unused struct.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Imre Deak <imre.deak@nokia.com>
I had a problem where doing an open after a close left the device
unusable. netif_carrier_on should be called whenever we go to the
associated state, but this is not so in case of a close->open sequence.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Adrian Bunk <bunk@stusta.de>
This patch contains the following possible cleanups:
- make needlessly global code static
- remove the unused IPW_DEBUG_ENABLED
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Pavel Machek <pavel@ucw.cz>
ipw2100 uses custom debug prints that are sometimes longer and always
harder to read than normal printk. They also introduced some bugs where
prefix is printed twice.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Pavel Machek <pavel@ucw.cz>
ipw2100 uses strange X__ prefixes even for symbols already prefixed
by ipw2100. Fixed.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
airo_cs is broken on m32r; marked as such. [Proper fix would involve
separating PCI-dependent parts and making sure they don't get in the
way _and_ arranging for asm/scatterlist.h getting picked on m32r]
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace remaining WLAN_FC_* defines with the ones used in ieee80211
header file. This completes the move from hostap version of frame
control field processing to ieee80211 version.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove backwards compatibility define for WLAN_CAPABILITY_ESS now that
net/ieee80211.h defines this.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
IEEE 802.11 has a capability field flag called ESS, but ieee80211 had
renamed this to BSS for some reason. hostap has been using
WLAN_CAPABILITY_ESS and since that matches with the standard, lets use
it as the name for this define. Add WLAN_CAPABILITY_BSS as a backwards
compatibility name for the same bit since ieee80211 and ipw2200 are
using this and there are versions outside kernel tree that expect to
find this define name.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace temporary HOSTAP_FC_GET_{TYPE,STYPE} macros with the ieee80211
version of WLAN_FC_GET_{TYPE,STYPE}.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove unused defines that are already available from generic kernel
header files.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace hardware model specific #ifdef's in struct local_info with
void *hw_priv that is pointing to cs/pci/plx specific data
structure. This removes unneeded #ifdef's and as such, is a step
towards making it possible to share objects for hostap_hw.c and
hostap_download.c with cs/pci/plx drivers without having to compile
and link the same code separately for each one.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PCI version of Prism2.5/3 has undocumented DMA support for TX/RX data,
but this seems to have some hardware bugs that prevent it from being
used properly for TX. RX side could possibly be made to work reliably.
Even though DMA support would be very useful for saving host CPU (from
about 40% to 5-10% when operating at maximum throughput), it seems to
be best to just remove this code finally. The implementation has
always been commented out by default and has received very limited
testing. The code may have already been broken number of times and I
don't have much interested in trying to verify whether it works or
not. Getting this out makes it easier to maintain the driver and
allows some cleanups that have been partly postponed because of this
experimental bus master/DMA code.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Old AP mode code for power saving was using skb->cb for couple of
flags before the more generic 802.11 TX code started using the same
buffer for struct hostap_skb_tx_data. This resulted in the power save
code corrupting the magic value in beginning of the buffer and TX code
dropping the power saved packets because of this for the case where
STAs send PS-Poll frames with PwrMgmt flag set.
This patch modifies the power save code to use the same struct
hostap_skb_tx_data as rest of the TX path in order to avoid corrupting
the data in skb->cb.
In addition, this patch reorders fields in the structure and makes
them use smaller types in order to make the structure fit in skb->cb
on 64-bit hosts.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add the device ID of the Buffalo AirStation WLI-CF-S11G
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A few sparse cleanups for orinoco.c
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace Host AP version of WEP, TKIP, CCMP implementation with
net/ieee80211 that has more or less identical implementation (since
it is based on the Host AP implementation). Remove Host AP specific
implementation and modules from drivers/net/wireless/hostap.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Preparations for starting to use net/ieee80211 instead of private
IEEE 802.11 implementation. Include net/ieee80211.h and
net/ieee80211_crypt.h into files that will be needed these in the
future. Remove duplicate definitions from hostap_common.h and
rename WLAN_FC_GET_{TYPE,STYPE} macros for now sinc net/ieee80211.h
is using incompatible definitions. This will be resolved in the
future by updating Host AP to use the versions that do not shift
type/stype.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed beacon frame when moving from monitor mode to master mode
(workaround for firmware bug that left IBSS IE in the Beacon
frames). This is using the same workaround that was previously used
when moving from adhoc mode to master mode.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Warning fix for 64-bit platforms
Hello!
The patch fixes following warning seen on 64-bit platforms (in my case -
x86_64, gcc-4.0):
In file included from /usr/local/src/hostap/driver/modules/hostap_cs.c:203:
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit_cb?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1674: warning: cast from pointer to integer of different size
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1758: warning: cast to pointer from integer of different size
prism2_transmit_cb uses a (void *) argument to get an integer. A
simple fix would be to use double cast from pointer to long and then to
int (and vice versa when int is passed as a pointer). But I prefer a
slightly longer patch.
I believe that whenever an argument can hold both a pointer and an
integer, it should be declared long. long can hold both pointers and
integers (except win64, but we are not coding for Windows), it can be
cast to both of them and it's never assumed to be a valid pointer, which
could be useful for some automatic code checkers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
line 129 of hostap_80211_rx.c should read:
LWNG_SETVAL(mactime, 2, 0, 4, rx_stats->mac_time);
not:
LWNG_SETVAL(mactime, 2, 0, 0, rx_stats->mac_time);
The length field is incorrect.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Firmware seems to be getting into odd state in host_roaming mode 2
when hostscan is used without join command, so try to fix this by
re-joining the current AP. This does not actually trigger a new
association if the current AP is still in the scan results.
This makes background scans (iwlist wlan0 scan) not to break data
connection when in host_roaming 2 mode, e.g., when using wpa_supplicant.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleaned up scan result processing by converting struct
hfa384x_scan_result into struct hfa384x_hostscan_result. This removes
special cases from result processing since the results are only used
in one, hostscan, format.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added support for setting channel mask for scan requests
('iwpriv wlan0 scan_channels 0x00ff' masks scans to use channels 1-8).
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add MODULE_VERSION information for the Host AP kernel modules and
update the version string to indicate which version of the external
Host AP driver is included in the kernel tree.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
pcmcia id_table for hostap_cs.c
Hi Jouni,
Here's a patch for adding a pcmcia id_table to hostap_cs.c as introduced
by the PCMCIA subsystem changes in linux-2.6.13-rc1. The id_table allows
hotplug (along with pcmciautils [1]) to load the driver without the need
for the pcmcia-cs cardmgr daemon.
The id_table was generated from the CVS version of hostap_cs.conf using
a script borrowed from Dominik Brodowski. I have removed any duplicate
entries, but I have only been able to test the functionality of the
patch with a Linksys WPC11v3.
Sincerely,
Brix
[1]: http://www.kernel.org/pub/linux/utils/kernel/pcmcia/
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
