Sometimes boards don't reset properly, and the address read out of the
EEPROM is zero. Stop the insanity before the device gets registered.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit side code has a number of ring problems that caused some
of the Bugzilla reports. Rather than trying to fix the details, it is safer
to rewrite the code that handles transmit completion and freeing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Consolidate all usage of ring low water mark to one value.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since accessing the PHY can take 100's of usecs, use a work queue to
allow spinning in outside of soft/hard irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch updates the myri10ge to 1.0.0, with the following changes:
* Switch to dma_alloc_coherent API.
* Avoid PCI burst when writing the firmware on chipset with unaligned completions.
* Use ethtool_op_set_tx_hw_csum instead of ethtool_op_set_tx_csum.
* Include linux/dma-mapping.h to bring DMA_32/64BIT_MASK on all architectures
(was missing at least on alpha).
* Some typo and warning fixes.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
drivers/net/myri10ge/myri10ge.c | 57 +++++++++++++++++++-----------
1 file changed, 37 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various PCI bus errors can be signaled by newer PCI controllers.
This patch adds the PCI error recovery callbacks to the intel gigabit
ethernet e1000 device driver. The patch has been tested, and appears
to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Various PCI bus errors can be signaled by newer PCI controllers. This
patch adds the PCI error recovery callbacks to the intel ethernet e100
device driver. The patch has been tested, and appears to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures. Remove them for now. We'll let them
stay in mm for a while, or find a better solution to enable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
New code added in 2.6.17 caused setup_irq to print a warning when
running ethtool -t eth0 offline.
This test marks the request_irq call made by this test as a "probe"
to see if the interrupt is shared or not.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
skb_clone() may fail, we should check the result.
Coverity CID: 1215.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matt Mackall <mpm@selenic.com>
netconsole is being wrong here. If it wasn't enabled there's no error.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
zd1201 is wifi adapter, yet it is hiding in drivers/usb/net where
noone can find it. This moves Kconfig/Makefile zd1201 to the right
place.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug logging in bcm43xx_ieee80211_set_security() is pretty noisy.
Make it more silent.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From: Florin Malita <fmalita@gmail.com>
The skb may be gone after netif_rx(), we can't use 'skb->len' to update the
stats. 'pkt_len' should work instead.
Coverity CID: 911.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also add the Poll RX DMA Memory workaround to the DMA4
(xmitstatus) path.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hi,
This patch add new PCI ID for r8169 driver.
RTL8110SBL has this PCI ID.
Please aply.
Yoichi
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds flow control support for tx and rx pause frames in
forcedeth.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original patch was using whitespaces instead of tabs.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During a code scan for another change I discovered that this call to
pcnet32_free_ring must be removed. If the open fails due to a lack of
memory all the ring structures are removed via the call to free_ring
and a subsequent call to open will dereference a null pointer in
pcnet32_init_ring.
Please apply to 2.6.17.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
(cherry picked from c653e6351e commit)
Fix section mismatch warnings:
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:arlan_probe from .text between 'init_module' (at offset
0x3526) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:init_arlan_proc from .text between 'init_module' (at offset
0x3539) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.exit.text:cleanup_arlan_proc from .text between 'cleanup_module' (at
offset 0x356c) and 'arlan_diagnostic_info_string'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix section mismatch warning:
WARNING: drivers/net/wireless/wavelan.o - Section mismatch: reference to
.init.text: from .text between 'init_module' (at offset 0x371e) and
'cleanup_module'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
increase the year dates to 2006 and bump the version to 1.0.109-k2
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
same as e1000 - remove the changelog from the driver code itself.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
deinline a few large functions as to allow the compiler to pick.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This mimics a change made in the e1000 driver that imitates a slick
tg3 way of avoiding grabbing the lock around restarting the tx queue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
There seemed to be another bug introduced as well as a performance hit
with the addtion of the sentinel descriptor workaround. Removal of
this workaround appears to prevent the hang. We'll take a risk
and remove it, as we had never seen the originally reported bug
under linux.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
user contributed fix for LAA across down/up, from tonychung00@users.sf.net.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Moved interrupt masking to before requesting the interrupt from the OS.
Moved interrupt enable to after netif_poll_enable. This fixes a racy
BUG() where polling would be running on another CPU at the same time
that netif_poll_enable would run.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
If a SIR dongle is built in the kernel while IRTTY_SIR is built
as a module, kernel compilation will fail.
Thus, the SIR dongle config should depend on the IRTTY_SIR.
Closes kernel bug# 6512
(http://bugzilla.kernel.org/show_bug.cgi?id=6512)
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o modify the rx refill logic and tail bump
o add counter for failures
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
new SMSC LAN83C185 10BaseT/100BaseTX PHY driver for the PHY subsystem
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch provides a sysfs interface to change some properties of the
ibmveth buffer pools (size of the buffers, number of buffers per pool,
and whether a pool is active). Ethernet drivers use ethtool to provide
this type of functionality. However, the buffers in the ibmveth driver
can have an arbitrary size (not only regular, mini, and jumbo which are
the only sizes that ethtool can change), and also ibmveth can have an
arbitrary number of buffer pools
Under heavy load we have seen dropped packets which obviously kills TCP
performance. We have created several fixes that mitigate this issue,
but we definitely need a way of changing the number of buffers for an
adapter dynamically. Also, changing the size of the buffers allows
users to change the MTU to something big (bigger than a jumbo frame)
greatly improving performance on partition to partition transfers.
The patch creates directories pool1...pool4 in the device directory in
sysfs, each with files: num, size, and active (which default to the
values in the mainline version).
Comments and suggestions are welcome...
--
Santiago A. Leon
Power Linux Development
IBM Linux Technology Center
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Mon, May 15, 2006 at 12:56:37AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.17-rc3-mm1:
>...
> git-netdev-all.patch
>...
> git trees
>...
This patch makes the needlessly global bus_speed[] static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The truncate threshold calculation to prevent receiver from getting stuck
was incorrect, and it didn't take into account the upper limit on bits
in the register so the jumbo packet support was broken.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
If the skb allocation fails, the current error path calls
dev_kfree_skb_irq() with a NULL argument. Also, 'err' is not being used.
Coverity CID: 275.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increment the driver version to 1.0.104-k2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This adds a TX timeout counter to the ethtool stats, a tx timeout
debug message, and sets the timer to 5 seconds.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use DPRINTK and msglvl, and ethtool to control it. Add proper names
to netdev structs and mappings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This adds a define for an awkward and uncommented value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Add support for Copper 10GbE device ID 109E
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Make default flow control only have *sending* of flow control packets
enabled, and fix to disable / enable flow control correctly. Set flow
control defaults to disable receiving flow control from the link
partner, to fix the transmit fifo overlow errata
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fix rare early completion when using TSO. This essentially is the
e1000 fix, with code that was mostly already written. Another skb frag
was also needed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use kmalloc() instead of a local array in bnx2_nvram_write().
Update version to 1.4.40.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug in bnx2_nvram_write() caused by a counter variable not
correctly incremented by 4.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing rx error counters for 5705 and newer chips.
Update version to 3.58.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb allocation fails, the current error path calls
dev_kfree_skb_irq() with a NULL argument. Also, 'err' is not being used.
Coverity CID: 275.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With Manfred Spraul <manfred@colorfullife.com> and
Andrew Morton <akpm@osdl.org>
Bring back this recently-reverted patch, only fixed.
Original changelog:
From: Ayaz Abdulla <aabdulla@nvidia.com>
This patch fixes the issues with multiple irqs.
I am resending based on feedback. I decoupled the dma mask for
consistent memory and fixed leak with multiple irq in error path.
Thanks to Manfred for catching the spin lock problem.
Fix it:
From: Manfred Spraul <manfred@colorfullife.com>
Fix bug introduced by ebf34c9b6f, covered in
http://bugzilla.kernel.org/show_bug.cgi?id=6568.
Remove second instance of the request_irq() calls: they were moved
from nv_open into nv_request_irq.
Thanks to Alistair Strachan <alistair@devzero.co.uk> for reporting and
persisting.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call pci_map_single() with the actual size of the receive
buffers, not 0 (which skb->len is initialized to by dev_alloc_skb()).
Signed-off-by: Erling A. Jacobsen <linuxcub@email.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver will get stuck (permanent transmit timeout), if the transmit
ring size is set too small. It needs to have enough ring elements to
hold one maximum size transmit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Skge driver always causes bad checksums on big-endian.
The checksum in the receive control block was being swapped
when it doesn't need to be.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the status ring processing can't keep up with the incoming frames,
it is more efficient to have NAPI keep scheduling the poll routine
rather than causing another interrupt.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.
Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed. This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.
A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.
This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert previous patch with subject "change mdelay to msleep and remove
from ISR path". This patch seems to have caused bigger problems than
it solved, and it didn't solve much of a problem to begin with...
Discussion about backing-out this patch can be found here:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114321570402396&w=2
The git commit associated w/ the original patch is:
6ba98d311d
Signed-off-by: John W. Linville <linville@tuxdriver.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert ebf34c9b6f. Maybe. Due to crashes
at shutdown - see http://bugzilla.kernel.org/show_bug.cgi?id=6568.
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the device-tree information more generic and more
like the pSeries virtual lan device. Also use the MAC
address from the device tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
sky2: prevent dual port receiver problems
x86_64: Check for bad dma address in b44 1GB DMA workaround
The ixp2000 driver for the enp2611 was developed on a board with
There's a bunch of unused exports in the wireless drivers; that's
bad since unused exports take up quite a bit of space in total;
the patch below removes them.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I still need this hack to work around the fact that softmac doesn't
attempt to associate when we bring the device up...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.
It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
three gigabit ports, but some enp2611 models only have two ports
(and only one onboard PM3386.) The current driver assumes there
are always three ports and so it doesn't work on the two-port
version of the board at all.
This patch adds a bit of logic to the enp2611 driver to limit the
number of ports to 2 if the second PM3386 isn't detected.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
On alpha:
drivers/net/dl2k.c: In function `rio_free_tx':
drivers/net/dl2k.c:768: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c:768: error: (Each undeclared identifier is reported only once
drivers/net/dl2k.c:768: error: for each function it appears in.)
drivers/net/dl2k.c: In function `receive_packet':
drivers/net/dl2k.c:896: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c: In function `rio_close':
drivers/net/dl2k.c:1803: error: `DMA_48BIT_MASK' undeclared (first use in this function)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Even with fiber cards ethtool reports that the connected port is TP,
the patch fix this.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
[IPV6]: skb leakage in inet6_csk_xmit
[BRIDGE]: Do sysfs registration inside rtnl.
[NET]: Do sysfs registration as part of register_netdevice.
[TG3]: Fix possible NULL deref in tg3_run_loopback().
[NET] linkwatch: Handle jiffies wrap-around
[IRDA]: Switching to a workqueue for the SIR work
[IRDA]: smsc-ircc: Minimal hotplug support.
[IRDA]: Removing unused EXPORT_SYMBOLs
[IRDA]: New maintainer.
[NET]: Make netdev_chain a raw notifier.
[IPV4]: ip_options_fragment() has no effect on fragmentation
[NET]: Add missing operstates documentation.
661FX7MI-S motherboard which uses the SiS 661FX chipset. The patch adds
an entry to mii_chip_info for the transceiver.
The PHY ids were found using the sis900_c_122.diff patch from
http://brownhat.org/sis900.html but that patch didn't solve the problem,
because the PHY at address 1 was already being chosen.
Without my patch, when bursts of packets arrive from other hosts on a
LAN, the interface dropped one roughly 10% of the time, causing
retransmits. There were fifth second pauses in refresh of large xterms,
and it made Netrek suck. I can provide further test data.
Workaround in lieu of patch is to use mii-tool to advertise
100baseTx-HD, then force renegotiation.
I wasn't able to identify the actual transceiver, so the description
field is a guess.
This patch is similar to Artur Skawina's patch:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114297516729079&w=2
I'm not sure, but I wonder if it means the default behaviour should be
changed, so as to better handle future transceivers.
Diff is against 2.6.16.13.
Signed-off-by: James Cameron <james.cameron@hp.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
make sure phy_map entries whose PHY address is masked are initialized
to NULL, given that other code (such as mdiobus_unregister for
instance) assumes that non-NULL phy_map entries are allocated
phy_devices
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
tg3_run_loopback doesn't check that dev_alloc_skb() returns anything
useful.
Even if dev_alloc_skb() fails to return an skb to us we'll happily go
on and assume it did, so we risk dereferencing a NULL pointer. Much
better to fail gracefully by returning -ENOMEM than crashing here.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sir_kthread.c pretty much duplicates the workqueue
functionality, we'd better switch. The SIR fsm has been merged into
sir_dev.c and thus sir_kthread.c is deleted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimal PNP hotplug support for the smsc-ircc2 driver. A modular
driver will be modprobed via hotplug, but still bypasses driver model
probing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newer board revision changed the type of ethernet phy.
Moreover, this generalizes the way that a phy gets switched
into fiber mode when autodetection is not available.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
We found a new chip setting that we need in order
to make the driver work more reliable.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
since the au1000 driver already selects the CRC32 routines, simply replace
the internal ether_crc() implementation with the semantically equivalent
one from <linux/crc32.h>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
It is more efficient not to write the status ring from the
processor and just read the active portion.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Mask for transmit ring status was picking up bits from the
unused sync ring. They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This is a backout of earlier patch.
The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Use NULL instead of 0 for a null pointer value (sparse warning):
drivers/net/irda/irda-usb.c:1781:30: warning: Using plain integer as NULL pointer
Also, correct timeout argument to use milliseconds instead of jiffies.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The resource data in the network device is intended for ISA and other
older busses, but not for PCI. Don't put PCI data there. Don't (ab)use
the network device for keeping the IRQ number.
Retire orinoco_pci_setup_netdev(), and print some minimal information to
the kernel log instead, identifying the network device and the driver
mostly to identify problems at startup. Scripts should rely on sysfs.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use flags in the spinlocks - the PCMCIA resume functions may not
be called under lock. Don't ignore any errors.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report only the first I/O window and IRQ, and also add the driver name.
The second I/O window, Vpp and configuration index are not interesting
to most users. They can be found by PCMCIA debug tools if needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware resources should not be made available to other devices while
the network device is still registered. Also remove the related debug
statements.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running Linux 2.6.17-rc3-mm1 which has this patch included I get this
interesting message:
airo(eth0): WPA unsupported (only firmware versions 5.30.17 and greater
support WPA. Detected 5.30.17)
airo_test_wpa_capable assumes that the softSubVer part of the firmware
version number is coded in BCD. Apparently, that's not true.
I have firmware version 5.30.17 and cap_rid.softSubVer is 0x11==17.
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the conditions under which we poke at the APHY registers in
bcm43xx_phy_initg() to avoid a machine check on chips where they don't
exist.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem here is that the bcm34xx driver and the ieee80211
stack do not agree on what channels are possible for 802.11a.
The ieee80211 stack only wants channels between 34 and 165, while
the bcm43xx driver accepts anything from 0 to 200. I made the
bcm43xx driver comply with the ieee80211 stack expectations, by
using the proper constants.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[mb]: Reduce stack usage by kzalloc-ing ieee80211_geo
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for valid MAC address in SPROM fields instead of relying on
PHY type while setting the MAC address in the networking subsystem,
as some devices have multiple PHYs.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a crash when
iwconfig ethX mode foo
is done before
ifconfig ethX up
or after
ifconfig ethX down
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the issues with multiple irqs.
I am resending based on feedback. I decoupled the dma mask for
consistent memory and fixed leak with multiple irq in error path.
Thanks to Manfred for catching the spin lock problem.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Fixes Rhine I cards disclosing fragments of previously transmitted frames
in new transmissions.
Before transmission, any socket buffer (skb) shorter than the ethernet
minimum length of 60 bytes was zero-padded. On Rhine I cards the data can
later be copied into an aligned transmission buffer without copying this
padding. This resulted in the transmission of the frame with the extra
bytes beyond the provided content leaking the previous contents of this
buffer on to the network.
Now zero-padding is repeated in the local aligned buffer if one is used.
Following a suggestion from the via-rhine maintainer, no attempt is made
here to avoid the duplicated effort of padding the skb if it is known that
an aligned buffer will definitely be used. This is to make the change
"obviously correct" and allow it to be applied to a stable kernel if
necessary. There is no change to the flow of control and the changes are
only to the Rhine I code path.
The patch has run on an in-service Rhine-I host without incident. Frames
shorter than 60 bytes are now correctly zero-padded when captured on a
separate host. I see no unusual stats reported by ifconfig, and no unusual
log messages.
Signed-off-by: Craig Brind <craigbrind@gmail.com>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Sat, Mar 11, Olaf Hering wrote:
> Why is the /sys/class/net/eth0/device symlink not created for the
> mv643xx_eth driver? Does this work for other platform device drivers?
> Seems to work for the ps2 keyboard at least.
The SET_NETDEV_DEV has to be done before a call to register_netdev. With
the new patch below, the device symlink for the platform device was
created. Unfortunately, after the 4 ls commands, the network connection
died. No idea if the box crashed or if something else broke, lost remote
access.
Provide sysfs 'device' in /class/net/ethN Also, set module owner field,
like pcnet32 driver does.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
The following patch contains fix related to init and shutdown of adapter
as per user guide. The list of changes include
1. shutdown gracefully.
2. Need to mask/unmask interrupts in ISR required fro Xframe-E
3. Tx FIFO should be enabled after WRR calender programming
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch contains additional statistics counters added to s2io driver
these statistics are very much usefull in debugging the driver.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch contains some of the bug fixes done for S2io driver.
Following are the brief description of changes
1. Continuing with initialization if we get minimum required MSI-X vectors
2. fix for ethtool online link test fails
3. make wait_for_cmd_complete generic for all command status registers
4. Print "Device is on PCI-E bus" for Xframe-E card
5. CX4 requires additional delay after sw_reset, and requires higher value for igp
6. Fixed panic due to non-TCP and/or LLC/SNAP traffic in case of lro
7. remove legacy code for old transponder
8. SPECIAL_REG_WRITE made to use 32-bit writes irrespective of system type
9. handle link interrupt as per user guide for Xframe II
10. Wait till all interrupts hndled
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
This patch contains the modification and bug fixes with respect to
input parameters and outupt dmesages. following is brief description
of the changes.
1. Set default values for rx_ring_sz[0..7] and tx_fifo_len[0..7]
2. verify few basic load parameters
3. read product description from VPD
4. clean up of dmesg when driver is loaded
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
This patch contains all the changes that were done to improve
performance of s2io driver. one line description of the changes
are
1. For Non NAPI case the rx interrupt handler is being called
unconditionally
2. code optimization and adding prefetch skb->data
3. Remove modulo operations in fast path
4. Enable Group Reads and set backoff interval to 0x1000
5. correct PIC_CNTL_SHARED_SPLITS macro definition, and reduce
pause parameter
6. Corrected logic of identifying rx buffer level in rx_buffer_level()
7. fix DMA map and unmap done with different sizes in 1-buf mode
8. Removed forcible disabling of ERO
9. Send up the packets with transfer code = 0x5
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix bug in nvram write function. If the starting nvram address offset
happens to be the last dword of the page, the NVRAM_CMD_LAST bit will
not get set in the existing code. This patch fixes the bug by changing
the "else if" to "if" so that the last dword condition always gets
checked.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With
the full chip reset during MAC address change, the automatic PHY reset
during chip reset will cause a link down and bonding will not work
properly as a result. With this reset_phy parameter, we can do a chip
reset without link down when changing MAC address or MTU.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the full chip reset when changing MAC address if ASF is enabled.
ASF sometimes uses a different MAC address than the driver. Without
the reset, the ASF MAC address may be overwritten when the driver's
MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some PHY workaround code to reduce jitter on some PHYs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_carrier_off() call during tg3_phy_reset(). This is needed
to properly track the netif_carrier state in cases where we do a
PHY reset with interrupts disabled. The SerDes code will not run
properly if the netif_carrier state is wrong.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the nic initialization. If the nic was in low power
mode, it brings it back to normal power. Also, it utilizes a new
hardware reset during the init.
I am resending based on feedback, I corrected the register size mapping
and delay after posted write.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.
The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
airo cards with firmware versions of 5.30.17 and higher support WPA.
This patch recognizes WPA-capable firmware versions and adds support for
retrieving the WPA and RSN information elements from the card's scan
results. The JOB and FLAG fields are now independent, since there was
no space left in the FLAG field for FLAG_WPA_CAPABLE.
Signed-off-by: matthieu castet <castet.matthieu@free.fr>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ipw2200 scan completion event feature will cause a potential event
race condition in wpa_supplicant. The patch fixes this problem by move the
ipw_disassociate() to the IW_AUTH_WPA_ENABLED event handling code.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->last_noise is not used with the exponential averaging algorithm
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makefile both IPW2200_RADIOTAP and IPW2200_PROMISCUOUS depend on
IPW2200_MONITOR. Let IPW2200_PROMISCUOUS select IPW2200_RADIOTAP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added version string fields so the version string indicates what is
configured (ie, you'll see 1.1.1kpmd if you are using a GIT snapshot
(Kernel.. previously -git), promiscuous (p), monitor (m), debug (d) build.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, a new promiscuous mode is enabled. If the module is loaded
with the rtap_iface=1 module parameter, two interfaces will be created
(instead of just one).
The second interface is prefixed 'rtap' and provides received 802.11 frames
on the current channel to user space in a radiotap header format.
Example usage:
% modprobe ipw2200 rtap_iface=1
% iwconfig eth1 essid MyNetwork
% dhcpcd eth1
% tcpdump -i rtap0
If you do not specify 'rtap_iface=1' then the rtap interface will
not be created and you will need to turn it on via:
% echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
You can filter out what type of information is passed to user space via
the rtap_filter sysfs entry. Currently you can tell the driver to
transmit just the headers (which will provide the RADIOTAP and IEEE
802.11 header but not the payload), to filter based on frame control
type (Management, Control, or Data), and whether to report transmitted
frames, received frames, or both.
The transmit frame reporting is based on a patch by Stefan Rompf.
Filters can be get and set via a sysfs interface. For example, set the
filter to only send headers (0x7), don't report Tx'd frames (0x10), and
don't report data frames (0x100):
% echo 0x117 > /sys/bus/pci/drivers/ipw2200/*/rtap_filter
All your packets are belong to us:
% tethereal -n -i rtap0
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects endian issues with the v3.0 fw image format.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch make ipw2200 generate the scan event every time a scan has
completed, so that user space know when to get fresh results.
Dan Williams would like to go towards this model in Network Manager
rather than having to poll.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works with the ieee80211 stack to set the correct QoS bit to the
ipw2200 card. It fixed the TX failure problem for using WPA with QoS.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces sliding averaging by exponential averaging for
reporting the wireless statistics for signal and noise level for ipw2200.
See details from: http://www.ces.clemson.edu/linux/ipw2200_averages.shtml
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make all Orinoco PCI drivers (orinoco_pci, orinoco_plx, orinoco_tmd and
orinoco_nortel) as similar as possible. Use the best implementation of
error handling, the best error messages, the best comments.
Put common code to orinoco_pci.h. For now, it's suspend and resume
functions and function for registering the network device.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy PCI suspend/resume functions from orinoco_pci.c.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to identify the card before possible allocation problems,
so that the user at least can report the firmware version that fails.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After several days of operation of Netgear MA311 card, the card becomes
to seek improperly and needs reset. This patch tries to reset the card
when this situation occurs.
Mar 9 06:45:16 berkeley kernel: wlan0: Error -5 writing packet to BAP
Mar 9 06:45:16 berkeley kernel: hermes @ f992a000: BAP0 offset error: reg=0x4044 id=0x128 offset=0x44
Mar 9 06:45:16 berkeley kernel: wlan0: Error -5 writing packet to BAP
Mar 9 06:45:16 berkeley kernel: hermes @ f992a000: BAP0 offset error: reg=0x4044 id=0x128 offset=0x44
(etc.)
A more detailed description of the problem can be found at
https://bugzilla.novell.com/show_bug.cgi?id=154773
The same problem with different card is reported at
http://sourceforge.net/mailarchive/message.php?msg_id=14597046
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use skb_pull() to strip the addresses from the original packet. Don't
strip protocol bytes.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The result of orinoco_xmit() can be OK, dropped packet and busy
transmitter. Rename labels accordingly. Increment stats->tx_errors in
one place. Increment stats->tx_dropped - nobody is doing it for us.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hermes_bap_pwrite() supports odd-sized packets now. There is no
minimal packet size for 802.11. Also, hermes_bap_pwrite() supports
odd-sized packets now. This removes all reasons to pad the Tx data.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new function can write an odd number of bytes, thus making padding
unnecessary.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't ever return -errno from orinoco_xmit() - the network layer doesn't
expect it.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing Tx exception, only read data until addr1. Rename
hermes_tx_descriptor_802_11 to hermes_txexc_data since it's only used to
Tx exceptions. Reuse existing hermes_tx_descriptor structure. Remove
fields after addr1 - they are not read from the card.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sparse is much better at finding endianess issues than such visual cues.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCMCIA drivers would never be loaded if the CIS were wrong.
No other PCMCIA drivers validate CIS.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes PIO mode on the softmac bcm43xx
driver. (A dscape patch will follow).
It mainly fixes endianess issues.
This patch is tested on PowerPC32 and i386.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was doing arithmetics on a little-endian value.
Reported by Stelios Koroneos <stelios@stelioscellar.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ibmveth_printk() is only used to print the driver version when the module
initializes, which means on all machines as long as it's compiled in.
If it's really only needed for debugging, boot with loglevel=8, or get
it from dmesg instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes several bugs in the gianfar driver, including a major one
where spinlocks were horribly broken:
* Split gianfar locks into two types: TX and RX
* Made it so gfar_start() now clears RHALT
* Fixed a bug where calling gfar_start_xmit() with interrupts off would
corrupt the interrupt state
* Fixed a bug where a frame could potentially arrive, and never be handled
(if no more frames arrived
* Fixed a bug where the rx_work_limit would never be observed by the rx
completion code
* Fixed a bug where the interrupt handlers were not actually protected by
their spinlocks
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Folks,
This patch (against 2.6.17-rc1) converts the cassini driver to the
pci_iomap API that will do the right thing, so architectures like
PARISC can stop screaming about illegal usage of ioremap() on
non-cacheable regions.
Tested on 64bit PARISC kernel.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>
> The patch was badly wordwrapped. Please fix and resend.
>
OK, I've fixed the wrapping and removed the CONFIG_ARM restriction. I've also did my
best to modify the C style to conform to the comments.
I noticed that the patch is getting ignored by majordomo due to its size >100K.
Should it be broken up somehow to allow posting to the lists?
Signed-off-by: Dustin McIntire <dustin@sensoria.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Straighten up the AMD Au1xx0 Ethernet probing code, make it print out (and
store in the 'net_device' structure) the physical address of the controller,
not the KSEG1-based virtual. Make the driver also claim/release the 4-byte MAC
enable registers and assign to the Ethernet ports two consecutive MAC
addresses to match those that are printed on their stickers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In a short discussion with Benjamin Herrenschmidt he mentioned
that Marvell PHYs are powered down the same way as the other
ones we currently handle. Thus actually do that, hopefully
saving some power during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The attached patch adds support for VLANs to the sis900 driver and bumps
the version number. It is based on an old (2003) patch for the 2.4
series by Hamid Hashemi Golpayegani. It applies on top of 2.6.16(.5).
I have one report that it works and behaves as intended.
Please review and consider for inclusion.
Signed-off-by: Daniele Venzano <venza@brownhat.org>
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the base address of the Realtek RTL8019AS chip on the Toshiba RBTX4938
board -- this should make the driver work at least when CONFIG_PCI is enabled.
Signed-off-by: Yuri Shpilevsky <yshpilevsky@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In a short discussion with Benjamin Herrenschmidt he mentioned
that Marvell PHYs are powered down the same way as the other
ones we currently handle. Thus actually do that, hopefully
saving some power during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The room for the names in bcm43xx_priv_wx_args[] are IFNAMSIZ long and
IFNAMSIZ is defined as 16, so the names in bcm43xx_priv_wx_args should
be 15 characters (16 including the trailing \0). This patch fixes that
for the "set_shortpreambl", "get_shortpreambl", "set_swencryption", and
"get_swencryption" private calls. Patch is against 2.6.17-rc1.
Signed-off-by: Erik Mouw <erik@harddisk-recovery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up the bcm43xx sysfs code and makes it compliant
with the unwritten sysfs rules (at least I hope so).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "depends on" to make all bcm43xx driver options be listed
at the same level.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix printk format warnings:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:456: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:460: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:476: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:480: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:200: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:311: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:733: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbol firmware F3.91-71 has an additional word in the commsquality RID.
Extend the receiving buffer by one word to accomodate it.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2.6.17-rc1 changed the title for the entry CONFIG_NET_RADIO. I
personally disagree with this change and want it reverted. Patch for
2.6.17-rc1.
Rationale : WIRELESS_EXT is an invisible option. Therefore,
the only way for a user to enable it is via NET_RADIO. Some users need
to do that for out-of-tree drivers. Therefore it should be mentionned
in the title of the option.
Rationale2 : the option just below is called "Wireless
Extension API over RtNetlink". Some users may confuse this option for
the main "Wireless Extension" option. Therefore reverting this change
help disambiguate the relation between those two options.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send scan completion events to user space when a scan completes.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
