SiS965 and SiS180 chips must support slave mode,
SiS965L and SiS964 chips must not support slave mode.
SCR_STATUS for SATA ports in powerdown state fixed.
Now returning 0x0113 instead of 0x0117. Avoids problem
on detecting sata_sis controller.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Instead of writing 0xf blindly, preserve the content of write-once
PORTS_IMPL register over host resets.
This patch is taken from Jeff Garzik's AHCI init update patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pdc_* functions are part of the global namespace for the PDC on PA-RISC
systems and this means our choice of pdc_ causes collisions between the
PDC globals and our static functions. Rename them to pdc202xx where they
are for both 2024x and 2026x.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move dev->max_sectors configuration from ata_scsi_dev_config() to
ata_dev_configure().
* more consistent.
* allows LLDs to peek at the default dev->max_sectors value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata EH used to perform ata_set_mode() iff the EH session performed
reset as indicated by ATA_EHI_DID_RESET. This is incorrect because
->dev_config() called by revalidation is allowed to modify transfer
mode which ata_set_mode() should take care of. This patch implements
the following two flags.
* ATA_EHI_SETMODE: set during EH to schedule ata_set_mode(). Both new
device attachment and revalidation set this flag.
* ATA_EHI_POST_SETMODE: set while the device is revalidated after
ata_set_mode(). Post-setmode revalidation is different from initial
configuaration and EH revalidation in that ->dev_config() is not
allowed tune transfer mode. LLD can use this flag to determine
whether it's allowed to tune transfer mode. Note that POST_SETMODE
->dev_config() is guaranteed to be preceded by non-POST_SETMODE
->dev_config().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ehi flag ATA_EHI_PRINTINFO. This flag is set when device
configuration needs to print out device info. This used to be handled
by @print_info argument to ata_dev_configure() but LLDs also need to
know about it in ->dev_config() callback.
This patch replaces @print_info w/ ATA_EHI_PRINTINFO and make sata_sil
print workaround messages only on the initial configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci-vt8251
* requires hardreset after PHY status change
* doesn't clear BSY on signature FIS after hardreset
* needs SError cleared for the port to operate after hardreset
This patch implements ahci_vt8251_hardreset() and sets
ATA_FLAG_HRST_TO_RESUME to handle the above behaviors. This fixes EH
including hotplug on vt8251.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out sata_port_hardreset() from sata_std_hardreset(). This
will be used by LLD hardreset implementation and later by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that ahci_softreset() is fixed to automatically perform CLO if
BSY/DRQ is set on entry, AHCI_FLAG_RESET_NEEDS_CLO is redundant. Kill
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make user scan wait for scan to complete. This way user can wait for
warm plug request to complete and is prevented from causing EH event
storm by repetitively issuing scan request while EH is in progress.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Fajun Chen <fajunchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NV controllers sometimes fail to perform softreset after hotplug.
Make it use hardreset to resume link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_irq_on() isn't used outside of libata core layer. The function is
TF/SFF interface specific but currently used by core path with some
hack too. Move it from include/linux/libata.h to
drivers/ata/libata-sff.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata waits for !BSY even when the status register reports 0xff.
This causes long boot delays when D8 isn't pulled down properly. This
patch does the followings.
* don't wait if status register is 0xff in all wait functions
* make ata_busy_sleep() return 0 on success and -errno on failure.
-ENODEV is returned on 0xff status and -EBUSY on other failures.
* make ata_bus_softreset() succeed on 0xff status. 0xff status is not
reset failure. It indicates no device. This removes unnecessary
retries on such ports. Note that the code change assumes unoccupied
port reporting 0xff status does not produce valid device signature.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Joe Jin <lkmaillist@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
needs a changelog
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for ADMA mode on NVIDIA nForce4 (CK804/MCP04) SATA
controllers to the sata_nv driver. Benefits of ADMA mode include:
- NCQ support
- Reduced CPU overhead (controller DMAs command information from memory
instead of them being pushed in by the CPU)
- Full 64-bit DMA support
ADMA mode is enabled by default in this version. To disable it, set the
module parameter adma_enabled=0.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- use pci_iomap() [Alan, version 0.0.5t]
- fix Alan's version 0.0.5t change
- line length, trailing whitespace, case indentation cleanups
- don't use deprecated ->eng_timeout() in a driver that uses new EH
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a legacy mode PATA driver for the 6101/45 and will also drive
the SATA ports 1 & 2 in legacy mode as well if desired. Tested and
confirmed working by users. The chip supports AHCI type behaviour for
SATA and has a more advanced PATA interface as well so this driver will
get it working but not get best performance for now.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_module_init() conversion for pata_pdc2027x
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@redhat.com> but please apply as follows to keep
revision id straight
Cc: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_module_init convertion in ata_generic.c.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Winbond 83759A support in non-multichip mode (afaik nobody ever used
multichip mode anyway). The 83759 is not supported by this driver as it
is already handled elsewhere and doens't use the same interfaces.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Many LLDs are missing sht->slave_destroy. The method is mandatory to
support device warm unplugging (echo 1 > /sys/.../delete). Without
it, libata might access released scsi device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
JMicron AHCI controllers set PORT_IRQ_IF_ERR on device errors. The
IRQ status bit indicates interface error or protocol mismatch and ahci
driver interprets it into AC_ERR_ATA_BUS. So, whenever an ATAPI
device raises check condition, ahci interprets it as ATA bus error and
thus resets it which, in turn, raises check condition thus creating a
reset loop and rendering the device unuseable.
This patch makes JMB controllers ignore PORT_IRQ_IF_ERR when
interpreting error condition.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Justin Tsai <justin@jmicron.com>
Fixes ata_sas_queuecmd to properly handle a failure from
__ata_scsi_queuecmd.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the Intel ICH9 AHCI controller DID's for SATA support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do not schedule EH for revalidation on wcache on/off if old EH. Old
EH cannot handle it and will result in WARN_ON()'s and oops.
This closes bug #7412.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When building a monolithic kernel, the load order of drivers does not
work for SAS libata users, resulting in a kernel oops.
Convert libata to use subsys_initcall instead of module_init, which
ensures that libata gets loaded before any LLDD.
This is the same thing that scsi core does to solve the problem. The
load order problem was observed on ipr SAS adapters and should exist for
other SAS users as well.
Signed-off-by: Brian King <brking@us.ibm.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A curious thing happens, however, when ata_qc_new_init fails to get
an ata_queued_cmd:
First, ata_qc_new_init handles the failure like this:
cmd->result = (DID_OK << 16) | (QUEUE_FULL << 1);
done(cmd);
Then, we return to ata_scsi_translate and do this:
err_mem:
cmd->result = (DID_ERROR << 16);
done(cmd);
It appears to me that first we set a status code indicating that we're
ok but the device queue is full and finish the command, but then
we blow away that status code and replace it with an error flag and
finish the command a second time! That does not seem to be desirable
behavior since we merely want the I/O to wait until a command slot
frees up, not send errors up the block layer.
In the err_mem case, we should simply exit out of ata_scsi_translate
instead.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Helps for PATA but SATA bridged devices lie and always set all the bits
so will need the error handling fixes from Tejun.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit f833229c96:
According to reviewers and the lspci data provided in commit message
itself, PCI ID 0x7110 should not have been added to ata_piix.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci_softreset() used to use ahci_tf_read() which reads D2H_REG area
to check for the Status register. However, this area is zeroed on
initialization and not set by initial signature FIS. Replace it with
ahci_check_status().
This bug prevented CLO code from being activated whenever BSY and/or
DRQ is set prior to softreset. This fix makes
AHCI_FLAG_RESET_NEEDS_CLO flag redundant.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ICH7M was separated from ICH6M to allow undocumented MAP value 01b
which was spotted on an ASUS notebook. However, there is also
notebooks with MAP value 01b on ICH6M. This patch re-merges ICH6M and
ICH7M entries and allows MAP value 01b for both.
This problem has been reported and initial patch provided by Jonathan
Dieter.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jonathan Dieter <jdieter@gmail.com>
Cc: Tom Deblauwe <tom.deblauwe@telenet.be>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_revalidate() isn't used outside of libata core. Unexport it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi Jeff,
I tested the PATA support on my old VAIO notebook, and it failed to find
my piix device:
00:07.1 Class 0101: 8086:7111 (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at fc90 [size=16]
This patch adds the pci id to ata_piix.c and things then work as
expected.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sis_init_one() modifies probe_ent->port_flags after allocating and
initializing it using ata_pci_init_native_mode(). This makes port_flags
for the secondary port (probe_ent->pinfo2->flags) go out of sync resulting
in misdetection of device due to incorrectly initialized SCR access flag.
This patch make probe_ent alloc/init happen after the final port flags
value is determined. This is fragile but probe_ent and all the related
mess are scheduled to go away soon for exactly this reason. We just need
to hold everything together till then.
This has been spotted and diagnosed and tested by Patrick McHardy.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Patric McHardy <kaber@trash.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are some Linux supported platforms that simply cannot hit the low
I/O addresses used by ATA legacy mode PCI mappings. These platforms have
a window for PCI space that is fixed by the board logic and doesn't
include the neccessary locations.
Provide a config option so that such platforms faced with a controller
that they cannot support simply error it and punt
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the following compile error with CONFIG_ATA=y, CONFIG_BLOCK=n:
...
CC drivers/ata/libata-scsi.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c: In function ‘ata_scsi_dev_config’:
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:791: warning: implicit declaration of function ‘blk_queue_max_sectors’
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:799: error: ‘request_queue_t’ undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:799: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:799: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:799: error: ‘q’ undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:800: warning: implicit declaration of function ‘blk_queue_max_hw_segments’
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c: In function ‘ata_scsi_slave_config’:
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ata/libata-scsi.c:831:
warning: implicit declaration of function ‘blk_queue_max_phys_segments’
make[3]: *** [drivers/ata/libata-scsi.o] Error 1
Bug report by Jesper Juhl.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use valid values for ICH8 map_db. With the old values, when the
controller was in Native mode, and SCC was 1 (drives configured for
IDE), any drive plugged into a slave port was not recognized. For
Combined Mode (and SCC is still 1), 2 is a value value for MAP.map_value,
and needs to be recognized.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
