11-eeh-move-to-powerpc.patch
Move arch/ppc64/kernel/eeh.c to arch//powerpc/platforms/pseries/eeh.c
No other changes (except for Makefile to build it)
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
10-EEH-enable-bugfix.patch
Bugfix: With the curent linux-2.6.14-rc2-git6, EEH errors are
ignored because thier detection requires an unused, uninitialized
flag to be set. This patch removes the unused flag.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
09-hotplug-bugfix.patch
In the current 2.6.14-rc2-git6 kernel, performing a Dynamic LPAR Add
of a hotplug slot will crash the system, with the following (abbreviated)
stack trace:
cpu 0x3: Vector: 700 (Program Check) at [c000000053dff7f0]
pc: c0000000004f5974: .__alloc_bootmem+0x0/0xb0
lr: c0000000000258a0: .update_dn_pci_info+0x108/0x118
c0000000000257c8 .update_dn_pci_info+0x30/0x118 (unreliable)
c0000000000258fc .pci_dn_reconfig_notifier+0x4c/0x64
c000000000060754 .notifier_call_chain+0x68/0x9c
The root cause was that __init __alloc_bootmem() was called long after
boot had finished, resulting in a crash because this routine is undefined
after boot time. The patch below fixes this crash, and adds some docs to
clarify the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
08-eeh-spin-counter.patch
One an EEH event is triggers, all further I/O to a device is blocked (until
reset). Bad device drivers may end up spinning in their interrupt handlers,
trying to read an interrupt status register that will never change state.
This patch moves that spin counter to a per-device structure, and adds
some diagnostic prints to help locate the bad driver.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
07-eeh-report-race.patch
When a PCI slot is isolated, all PCI functions under that slot are affected.
If hese functions have separate device drivers, the EEH isolation event
might be reported multiple times. This patch adds a lock to prevent the
racing of such multiple reports. It also marks every device under the slot
as having experienced an EEH event, so that multiple reports may be
recognized more easily.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
06-eeh-empty-slot-error.patch
Performing PCI config-space reads to empty PCI slots can lead to reports of
"permanent failure" from the firmware. Ignore permanent failures on empty slots.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
05-eeh-slot-error-detail.patch
This patch encapsulates a section of code that reports the EEH event.
The new subroutine can be used in several places to report the error.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
04-eeh-statistics.patch
This minor patch adds some statistics-gathering counters that allow the
behaviour of the EEH subsystem o be monitored. While far from perfect,
it does provide a rudimentary device that makes understanding of the
current state of the system a bit easier.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
03-eeh-addr-cache-cleanup.patch
This is a minor patch to clean up a buglet related to the PCI address cache.
(The buglet doesn't manifes itself unless there are also bugs elsewhere,
which is why its minor.). Also:
-- Improved debug printing.
-- Declare some private routines as static
-- Adds reference counting to struct pci_dn->pcidev structure
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
02-eeh-minor-cleanup.patch
This patch performs some minor cleanup of the eeh.c file, including:
-- trim some trailing whitespace
-- remove extraneous #includes
-- use the macro PCI_DN uniformly, instead of the void pointer chase.
-- typos in comments
-- improved debug printk's
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
01-pci-dn-uniformization.patch
This patch changes the rtas_pci interface to use the new struct pci_dn
structure for two routines that work with pci device nodes.
This patch also does some minor janitorial work: it uses some handy macros
and cleans up some trailing whitespace in the affected file.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Early calls to __ioremap() will panic if the hash insertion fails. This
patch makes them return NULL instead. It happens with some pSeries users
who enabled CONFIG_BOOTX_TEXT. The later is getting an incorrect address
for the fame buffer and the hash insertion fails. With this patch, it
will display an error instead of crashing at boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a few compile warnings
arch/ppc64/boot/addRamDisk.c:166: warning: int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:170: warning: int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:265: warning: unsigned int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:302: warning: unsigned int format, long unsigned int arg (arg 3)
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A stripped vmlinux does not contain enough symbols to recreate the
System.map. The System.map file is only used to determine the end of
the runtime memory size. This is the same value (rounded up to
PAGE_SIZE) as ->memsiz in the ELF program header.
Also, the target vmlinux.initrd doesnt work in 2.6.14:
arch/ppc64/boot/addRamDisk arch/ppc64/boot/ramdisk.image.gz vmlinux.strip arch/ppc64/boot/vmlinux.initrd
Name of vmlinux output file missing.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove initialization of local variables.
They get all values assigned before use.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Due to the recent update of the platform code, some platform device
drivers fail to compile. This fix is for fs_enet, adding #include of a
new header, to which a number of platform stuff has been relocated.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes ppc44x fpu support that broke from a bad arch/powerpc merge.
Instead of adding KernelFP back in (which duplicates code) we use
the same kernel fpu unavailable handler as classic PPC processors.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves a bunch of files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
abs_addr.h
compat.h
lppaca.h
paca.h
tce.h
cpu_setup_power4.S
ioctl32.c
firmware.c
pacaData.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
- pacaData.c renamed paca.c to remove studlyCaps
- Misplaced { moved in lppaca.h
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges current.h. This is a one-big-ifdef merge, but both
versions are so tiny, I think we can live with it. While we're at it,
we get rid of the fairly pointless redirection through get_current()
in the ppc64 version.
Built and booted on POWER5 LPAR (ARCH=powerpc & ARCH=ppc64). Built
for 32-bit pmac (ARCH=powerpc & ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having already merged the ppc and ppc64 versions of signal.c, this
patch finishes the job by merging signal.h. The two versions were
almost identical already. Notable changes:
- We use BITS_PER_LONG to correctly size sigset_t
- Remove some uneeded #includes and struct forward
declarations. This does mean adding an include to signal_32.c which
relied on the indirect inclusion of sigcontext.h
- As the ppc64 version, the merged signal.h has prototypes for
do_signal() and do_signal32(). Thus remove extra prototypes from
ppc_ksyms.c which had them directly.
Built and booted on POWER5 LPAR (ARCH=ppc64 and ARCH=powerpc). Built
for 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- Re-add a hunk lost during merge: ppc64 is missing the hunk that disables
preempt on the secondary CPUs before they call cpu_idle().
- ppc's cpu_idle() had the need_resched() test wrong.
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
recalc_task_prio() is called from activate_task() to calculate dynamic
priority and interactive credit for the activating task. For real-time
scheduling process, all that dynamic calculation is thrown away at the end
because rt priority is fixed. Patch to optimize recalc_task_prio() away
for rt processes.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <piggin@cyberone.com.au>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem (eject not working on ATAPI LS-120 drive) is caused by
idefloppy_ioctl() function which *first* tries generic_ide_ioctl()
and *only* if it fails with -EINVAL, proceeds with the specific ioctls.
The generic eject command fails with something other than -EINVAL
and the specific one is never executed.
This patch fixes it by first going through the internal ioctls
and only trying generic_ide_ioctl() if none of them matches.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
wbsd_*_remove() is declared as __devexit but __devexit_p isn't used
when taking their addresses.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The siimage driver proports to support the Adaptec SA-1210 SATA
controller. However, at least some of those cards boot-up with their
interrupts disabled internally. The siimage driver currently ignores
that fact, so that driver does not actually work with those cards.
This patch enables those interrupts on cards that need it.
[ This is implemented based on similar code in the libata-based
sata_sil driver. ]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Matthew Wilcox asked that this got a comment explaining why it is done
so here it is.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
AGP shouldn't use "global_flush_tlb()" to flush the AGP mappings, that i
spurely an x86'ism. The proper AGP mapping flusher that should be used
is "flush_agp_mappings()", which on x86 obviously happens to do a global
TLB flush.
This makes AGP (or at least the config _I_ happen to use) compile again
on ppc64.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
From: "Jordan Crouse" <jordan.crouse@amd.com>
The core IDE engine on the CS5536 is the same as the other AMD southbridges,
so unlike the CS5535, we can simply add the appropriate PCI headers to
the existing amd74xx code.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch started life as a response to fedora specific ide subsystem changes
that made error handling of my ATAPI tape drive fail; the specifics are in
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=160868
The insertion of the statement rq->errors = err; near the end of
ide_end_drive_cmd() in drivers/ide/ide-io.c means that rq->errors does not
contain what it needs to in idescsi_end_request() in drivers/scsi/ide-scsi.c
anymore. Recent mainline kernels now also have this change.
The patch below makes ide-scsi whole.
Signed-off-by: Willem Riede <wrlk@riede.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch contains the following possible cleanups:
- pci/cy82c693.c: make a needlessly global function static
- remove the following unneeded EXPORT_SYMBOL's:
- ide-taskfile.c: do_rw_taskfile
- ide-iops.c: default_hwif_iops
- ide-iops.c: default_hwif_transport
- ide-iops.c: wait_for_ready
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CONFIG_IDE_MAX_HWIFS is a generic thing, no need to have it duplicated
by every arch that uses it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Devices driven by ide-cs will appear under /sys/devices instead of the
appropriate PCMCIA device. To fix this I had to extend the hw_regs_t
structure with a 'struct device' field, which allows us to set the
parent link for the appropriate hwif.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@suse.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do not include .config for target kernelrelease
Signed-off-by: Uwe Zeisberger <zeisberg@informatik.uni-freiburg.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated. A
similar delay was needed with earlier ISPs.
Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct issue where abort I/O command was not being issued
when the loop-state was down.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When mulitple initiators are coming up in an FCAL topology.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On MMIO relaxed-order platforms, it is possible for the
proper delay during NVRAM access to begin before the request
passes through the PCI bus (via a MMIO write) to the ISP.
Thus, causing a subsequent read to the NVRAM part to fail.
Add a MMIO read, after the MMIO write to insure any posted
writes are flushed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
The return data from a read capacity 16 needs to have RTO_EN and PROT_EN
zeroed out.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
