This is my libata compatible low level driver for the Marvell SATA
family. Currently it successfully runs in PIO mode on a 6081 chip.
EDMA support is in the works and should be done shortly. Review,
testing (especially on other flavors of Marvell), comments welcome.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ata_get_mode_mask() uses bits 3 and 4 in the pio_mask to represent PIO
modes 3 and 4. The value read from the drive, which reports support
for PIO3 and PIO4 in bits 0 and 1, is shifted left by 3 bits and OR'd
with 0x7 (which then corresponds to PIO 2-0 in libata). Thus, the
drivers below need adjustments to comply with the way pio_mask is
used. I changed the masks from the commented values to all support
PIO4-0, since the spec mandates that PIO0-2 are supported and there's
no reason not to support PIO3 IMO.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
No code changes, just Lindent + manual fixups.
This prepares us for updating to the latest Intel driver code, plus
gives the source code a nice facelift.
Need to use compat struct sizes and compat_sys_ioctl().
Reported by Adrian Bunk via kernel bugzilla #2683
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Max Kellermann <max@duempel.org>
The sunrpc stats are collected in unsigned integers, but they are printed
with '%d'. That can result in negative numbers in /proc/net/rpc when the
highest bit of a counter is set. The following patch changes '%d' to '%u'
where appropriate.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
proto_unregister holds a lock while calling kmem_cache_destroy, which
can sleep.
Noticed by Daniele Orlandi <daniele@orlandi.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
result of comma operator is not an lvalue
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Dan Williams already included most parts of my WE-19 patch for
the airo driver in the kernel. There was just a few bits he could not
do because WE-19 itself was not in the kernel. Those are the missing
bits.
Tested with 2.6.13 (with real HW).
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
My patch that adds WE-17 support to the Prism54 driver went
already in the kernel, except for a tiny bit that was dropped on the
way. This is the missing bit....
Tested with 2.6.13 (with real HW).
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
wl3501_cs won't compile with WE-19. This patches fixes it.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Acked-by: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This adds support for WE-17 to the atmel_cs driver. Not
tested, I don't have the HW.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This adds support for WE-17 to the netwave_cs driver. Tested
with 2.6.13 (with real HW).
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This adds support for WE-17 to the ray_cs driver. Tested
with 2.6.13 (with real HW).
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi Jeff,
This is version 19 of the Wireless Extensions. It was supposed
to be the fallback of the WPA API changes, but people seem quite happy
about it (especially Jouni), so the patch is rather small.
The patch has been fully tested with 2.6.13 and various
wireless drivers, and is in its final version. Would you mind pushing
that into Linus's kernel so that the driver and the apps can take
advantage ot it ?
It includes :
o iwstat improvement (explicit dBm). This is the result of
long discussions with Dan Williams, the authors of
NetworkManager. Thanks to him for all the fruitful feedback.
o remove pointer from event stream. I was not totally sure if
this pointer was 32-64 bits clean, so I'd rather remove it and be at
peace with it.
o remove linux header from wireless.h. This has long been
requested by people writting user space apps, now it's done, and it
was not even painful.
o final deprecation of spy_offset. You did not like it, it's
now gone for good.
o Start deprecating dev->get_wireless_stats -> debloat netdev
o Add "check" version of event macros for ieee802.11
stack. Jiri Benc doesn't like the current macros, we aim to please ;-)
All those changes, except the last one, have been bit-roting on
my web pages for a while...
Patches for most kernel drivers will follow. Patches for the
Orinoco and the HostAP drivers have been sent to their respective
maintainers.
Have fun...
Jean
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Another small update for the spidernet driver to fix a bug encountered
during testing our latest hardware with dual-ethernet support.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Prevent PCI posting problems by using synchronous register access
in critical places
- Check return value from firmware device tree functions
- fix device cleanup
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds a driver for a new 1000 Mbit ethernet NIC. It is
integrated on the south bridge that is used for our Cell Blades.
The code gets the MAC address from the Open Firmware device tree, so it
won't compile on platforms other than ppc64.
This is the first public release, so I don't expect the first version to
get merged, but I'd aim for integration within the 2.6.13 time frame.
Cc: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
My overlords have asked me to update the copyright notice for iseries_veth.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
no need to mess with (wrong) casts for ->mem_start, when we have the
original iomem pointer used to set ->mem_start in the first place...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch contains the following hardware related fixes and other
miscellaneous bug fixes.
1. Updated the definition of single and double-bit ECC errors
2. Earlier we were allocating Transmit descriptors equal to
MAX_SKB_FRAGS. This was causing a boundary condition failure.
Need to allocate MAX_SKB_FRAGS+1 descriptors.
3. On some platforms(like PPC), pci_alloc_consistent() can return
a zero DMA address. Since the NIC cannot handle zero-addresses,
a workaround has been provided. Basically, we don't use such
that page. We reallocate.
4. If list_info allocation failed during driver load, check for
it during driver exit and return instead of trying to dereference
NULL pointer.
5. Increase the debug level of few non-critical debug messages.
6. Reset the card on critical ECC double errors only in case of
XframeI since XframeII can recover from such errors.
7. Print copyright message on driver load.
8. Bumped up the driver version no. to 2.0.8.1
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This was found by inspection while looking for checksum problems
with the skge driver that sets CHECKSUM_HW. It did not fix the
problem, but it looks like it is needed.
If IP reassembly is trimming an overlapping fragment, it
should reset (or adjust) the hardware checksum flag on the skb.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ax2asc was still using a static buffer for all invocations which isn't
exactly SMP-safe. Change ax2asc to take an additional result buffer as
the argument. Change all callers to provide such a buffer.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new timestamp get/set routines should have const attribute
on parameters (helps to indicate direction).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This broke the pam audit module which includes an incorrect check for
-ENOENT instead of -EPROTONOTSUPP.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
scsi_io_completion() can be a bit noisy about certain conditions.
Previously this wasn't a problem for internally generated commands,
since they never hit it. However, since we do all SCSI commands via
bios, now they do. user CD testers like magicdev are now getting not
ready messages every time they touch the CD to see if there's anything
in it.
Fix this by making all scsi_execute commands REQ_QUIET and making
scsi_finish_io() not say anything for REQ_QUIET.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This returns always false with new-style drivers right now. Make it
return always true instead, as a host must be present if we are able
to call the ioctl (without a host attached there would be no device
node to call on..)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Fri, Dec 13, 2002 at 12:24:39AM +1100, Anton Blanchard wrote:
> We tested 2.5.51 on a ppc64 box, qlogic 2312 and a fastt700 array. I
> had CONFIG_SCSI_REPORT_LUNS and unfortunately it thought the management
> LUN was a disk:
>
> Vendor: IBM Model: Universal Xport Rev: 0520
> Type: Direct-Access ANSI SCSI revision: 03
>
> ...
>
> SCSI device sdaj: drive cache: write through
> SCSI device sdaj: 40960 512-byte hdwr sectors (21 MB)
> sdaj: unknown partition table
> Attached scsi disk sdaj at scsi2, channel 0, id 0, lun 31
>
> ...
>
> end_request: I/O error, dev sdaj, sector 0
Three years later...
It looks like SGI use the same FC vendor and they already have a
workaround for this issue. The following patch adds the IBM version of
it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a delay tailored for USB flash devices that are slow to
initialize their firmware. The symptom is a repeated Unit Attention with
ASC=0x28 (Not Ready to Ready transition). The patch will wait for up to 5
seconds for such devices to become ready. Normal devices won't send the
repeated Unit Attention sense key and hence won't trigger the patch.
This fixes a problem with James Roberts-Thomson's USB device, and I've
seen several reports of other devices exhibiting the same symptoms --
presumably they will be helped as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The problem lies in the way the error handler uses TEST UNIT READY to
tell whether error recovery has succeeded. The scsi_eh_tur function
gives up after one round of retrying; after that it decides that more
error recovery is needed.
However TUR is liable to report sense data indicating a retry is needed
when in fact error recovery has succeeded. A typical example might be
SK=2, ASC=4, ASCQ=1 (Logical unit in process of becoming ready). The mere
fact that we were able to get a sensible reply to the TUR should indicate
that the device is working well enough to stop error recovery.
I ran across a case back in January where this happened. A CD-ROM drive
timed out the INQUIRY command, and a device reset fixed the blockage.
But then the drive kept responding with 2/4/1 -- because it was spinning
up I suppose -- until the error handler gave up and placed it offline.
If the initial INQUIRY had received the 2/4/1 instead, everything would
have worked okay. It doesn't seem reasonable for things to fail just
because the error handler had started running.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The maximum size of a scatter-gather list that the current IBM VSCSI
Client can handle is 10. This patch adds large scatter-gather support
to the client so that it is capable of handling up to SG_ALL(255)
number of requests in the scatter-gather list.
Signed-off-by: Linda Xie <lxie@us.ibm.com>
Acked by: Dave C Boutcher <sleddog@us.ibm.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The following patch kills __ip_ct_expect_unlink_destroy and export
unlink_expect as ip_ct_unlink_expect. As it was discussed [1], the function
__ip_ct_expect_unlink_destroy is a bit confusing so better do the following
sequence: ip_ct_destroy_expect and ip_conntrack_expect_put.
[1] https://lists.netfilter.org/pipermail/netfilter-devel/2005-August/020794.html
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the NAT module is loaded when connections are already confirmed
it must not change their tuples anymore. This is especially important
with CONFIG_NETFILTER_DEBUG, the netfilter listhelp functions will
refuse to remove an entry from a list when it can not be found on
the list, so when a changed tuple hashes to a new bucket the entry
is kept in the list until and after the conntrack is freed.
Allocate the exact conntrack tuple for NAT for already confirmed
connections or drop them if that fails.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Connection mark tracking support is one of the feature in connection
tracking, so IP_NF_CONNTRACK_MARK depends on IP_NF_CONNTRACK.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A permanent expectation exists until timeing out and can expect
multiple related connections.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
