This patch simply defines CONFIG_ZONE_DMA for all arches. We later do special
things with CONFIG_ZONE_DMA after the VM and an arch are prepared to work
without ZONE_DMA.
CONFIG_ZONE_DMA can be defined in two ways depending on how an architecture
handles ISA DMA.
First if CONFIG_GENERIC_ISA_DMA is set by the arch then we know that the arch
needs ZONE_DMA because ISA DMA devices are supported. We can catch this in
mm/Kconfig and do not need to modify arch code.
Second, arches may use ZONE_DMA in an unknown way. We set CONFIG_ZONE_DMA for
all arches that do not set CONFIG_GENERIC_ISA_DMA in order to insure backwards
compatibility. The arches may later undefine ZONE_DMA if their arch code has
been verified to not depend on ZONE_DMA.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset follows up on the earlier work in Andrew's tree to reduce the
number of zones. The patches allow to go to a minimum of 2 zones. This one
allows also to make ZONE_DMA optional and therefore the number of zones can be
reduced to one.
ZONE_DMA is usually used for ISA DMA devices. There are a number of reasons
why we would not want to have ZONE_DMA
1. Some arches do not need ZONE_DMA at all.
2. With the advent of IOMMUs DMA zones are no longer needed.
The necessity of DMA zones may drastically be reduced
in the future. This patchset allows a compilation of
a kernel without that overhead.
3. Devices that require ISA DMA get rare these days. All
my systems do not have any need for ISA DMA.
4. The presence of an additional zone unecessarily complicates
VM operations because it must be scanned and balancing
logic must operate on its.
5. With only ZONE_NORMAL one can reach the situation where
we have only one zone. This will allow the unrolling of many
loops in the VM and allows the optimization of varous
code paths in the VM.
6. Having only a single zone in a NUMA system results in a
1-1 correspondence between nodes and zones. Various additional
optimizations to critical VM paths become possible.
Many systems today can operate just fine with a single zone. If you look at
what is in ZONE_DMA then one usually sees that nothing uses it. The DMA slabs
are empty (Some arches use ZONE_DMA instead of ZONE_NORMAL, then ZONE_NORMAL
will be empty instead).
On all of my systems (i386, x86_64, ia64) ZONE_DMA is completely empty. Why
constantly look at an empty zone in /proc/zoneinfo and empty slab in
/proc/slabinfo? Non i386 also frequently have no need for ZONE_DMA and zones
stay empty.
The patchset was tested on i386 (UP / SMP), x86_64 (UP, NUMA) and ia64 (NUMA).
The RFC posted earlier (see
http://marc.theaimsgroup.com/?l=linux-kernel&m=115231723513008&w=2) had lots
of #ifdefs in them. An effort has been made to minize the number of #ifdefs
and make this as compact as possible. The job was made much easier by the
ongoing efforts of others to extract common arch specific functionality.
I have been running this for awhile now on my desktop and finally Linux is
using all my available RAM instead of leaving the 16MB in ZONE_DMA untouched:
christoph@pentium940:~$ cat /proc/zoneinfo
Node 0, zone Normal
pages free 4435
min 1448
low 1810
high 2172
active 241786
inactive 210170
scanned 0 (a: 0 i: 0)
spanned 524224
present 524224
nr_anon_pages 61680
nr_mapped 14271
nr_file_pages 390264
nr_slab_reclaimable 27564
nr_slab_unreclaimable 1793
nr_page_table_pages 449
nr_dirty 39
nr_writeback 0
nr_unstable 0
nr_bounce 0
cpu: 0 pcp: 0
count: 156
high: 186
batch: 31
cpu: 0 pcp: 1
count: 9
high: 62
batch: 15
vm stats threshold: 20
cpu: 1 pcp: 0
count: 177
high: 186
batch: 31
cpu: 1 pcp: 1
count: 12
high: 62
batch: 15
vm stats threshold: 20
all_unreclaimable: 0
prev_priority: 12
temp_priority: 12
start_pfn: 0
This patch:
In two places in the VM we use ZONE_DMA to refer to the first zone. If
ZONE_DMA is optional then other zones may be first. So simply replace
ZONE_DMA with zone 0.
This also fixes ZONETABLE_PGSHIFT. If we have only a single zone then
ZONES_PGSHIFT may become 0 because there is no need anymore to encode the zone
number related to a pgdat. However, we still need a zonetable to index all
the zones for each node if this is a NUMA system. Therefore define
ZONETABLE_SHIFT unconditionally as the offset of the ZONE field in page flags.
[apw@shadowen.org: fix mismerge]
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Values are available via ZVC sums.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Values are readily available via ZVC per node and global sums.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Function is unnecessary now. We can use the summing features of the ZVCs to
get the values we need.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nr_free_pages is now a simple access to a global variable. Make it a macro
instead of a function.
The nr_free_pages now requires vmstat.h to be included. There is one
occurrence in power management where we need to add the include. Directly
refrer to global_page_state() there to clarify why the #include was added.
[akpm@osdl.org: arm build fix]
[akpm@osdl.org: sparc64 build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The global and per zone counter sums are in arrays of longs. Reorder the ZVCs
so that the most frequently used ZVCs are put into the same cacheline. That
way calculations of the global, node and per zone vm state touches only a
single cacheline. This is mostly important for 64 bit systems were one 128
byte cacheline takes only 8 longs.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is again simplifies some of the VM counter calculations through the use
of the ZVC consolidated counters.
[michal.k.k.piotrowski@gmail.com: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The determination of the dirty ratio to determine writeback behavior is
currently based on the number of total pages on the system.
However, not all pages in the system may be dirtied. Thus the ratio is always
too low and can never reach 100%. The ratio may be particularly skewed if
large hugepage allocations, slab allocations or device driver buffers make
large sections of memory not available anymore. In that case we may get into
a situation in which f.e. the background writeback ratio of 40% cannot be
reached anymore which leads to undesired writeback behavior.
This patchset fixes that issue by determining the ratio based on the actual
pages that may potentially be dirty. These are the pages on the active and
the inactive list plus free pages.
The problem with those counts has so far been that it is expensive to
calculate these because counts from multiple nodes and multiple zones will
have to be summed up. This patchset makes these counters ZVC counters. This
means that a current sum per zone, per node and for the whole system is always
available via global variables and not expensive anymore to calculate.
The patchset results in some other good side effects:
- Removal of the various functions that sum up free, active and inactive
page counts
- Cleanup of the functions that display information via the proc filesystem.
This patch:
The use of a ZVC for nr_inactive and nr_active allows a simplification of some
counter operations. More ZVC functionality is used for sums etc in the
following patches.
[akpm@osdl.org: UP build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After do_wp_page has tested page_mkwrite, it must release old_page after
acquiring page table lock, not before: at some stage that ordering got
reversed, leaving a (very unlikely) window in which old_page might be
truncated, freed, and reused in the same position.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With CONFIG_SPARSEMEM=y:
mm/rmap.c:579: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'int'
Make __page_to_pfn() return unsigned long.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
find_min_pfn_for_node() and find_min_pfn_with_active_regions() sort
early_node_map[] on every call. This is an excessive amount of sorting and
that can be avoided. This patch always searches the whole early_node_map[]
in find_min_pfn_for_node() instead of returning the first value found. The
map is then only sorted once when required. Successfully boot tested on a
number of machines.
[akpm@osdl.org: cleanup]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the last vestiges of the long-deprecated "MAP_ANON" page protection
flag: use "MAP_ANONYMOUS" instead.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the pointer passed to cache_reap to determine the work pointer and
consolidate exit paths.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up __cache_alloc and __cache_alloc_node functions a bit. We no
longer need to do NUMA_BUILD tricks and the UMA allocation path is much
simpler. No functional changes in this patch.
Note: saves few kernel text bytes on x86 NUMA build due to using gotos in
__cache_alloc_node() and moving __GFP_THISNODE check in to
fallback_alloc().
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Christoph Lameter <christoph@lameter.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PageSlab debug check in kfree_debugcheck() is broken for compound
pages. It is also redundant as we already do BUG_ON for non-slab pages in
page_get_cache() and page_get_slab() which are always called before we free
any actual objects.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TI FlasMedia controller attempts to validate command responses and
issues a "status error" if response does not matches its perceived
(by controller) value. As mmc layer does its own validation we can
safely ignore the controller's opinion.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This is kind of hokey, we could use the hardware provided facilities
much better.
MSIs are assosciated with MSI Queues. MSI Queues generate interrupts
when any MSI assosciated with it is signalled. This suggests a
two-tiered IRQ dispatch scheme:
MSI Queue interrupt --> queue interrupt handler
MSI dispatch --> driver interrupt handler
But we just get one-level under Linux currently. What I'd like to do
is possibly stick the IRQ actions into a per-MSI-Queue data structure,
and dispatch them form there, but the generic IRQ layer doesn't
provide a way to do that right now.
So, the current kludge is to "ACK" the interrupt by processing the
MSI Queue data structures and ACK'ing them, then we run the actual
handler like normal.
We are wasting a lot of useful information, for example the MSI data
and address are provided with ever MSI, as well as a system tick if
available. If we could pass this into the IRQ handler it could help
with certain things, in particular for PCI-Express error messages.
The MSI entries on sparc64 also tell you exactly which bus/device/fn
sent the MSI, which would be great for error handling when no
registered IRQ handler can service the interrupt.
We override the disable/enable IRQ chip methods in sun4v_msi, so we
have to call {mask,unmask}_msi_irq() directly from there. This is
another ugly wart.
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we can't use the generic MSI code.
Furthermore, properly use the {get,set}_irq_foo() abstracted
interfaces instead of direct accesses to irq_desc[]->foo.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some partitioning systems create special partitions that
span the entire disk. One example are Sun partitions, and
this whole-disk partition exists to tell the firmware the
extent of the entire device so it can load the boot block
and do other things.
Such partitions should not be treated as normal partitions,
because all the other partitions overlap this whole-disk one.
So we'd see multiple instances of the same UUID etc. which
we do not want. udev and friends can thus search for this
'whole_disk' attribute and use it to decide to ignore the
partition.
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I forgot to test build this part of the networking code... Sorry guys.
This patch renames u.rt_next to u.dst.rt_next
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems to miss RO mode path by IPv6 over IPv4 IPsec tunnel patch
when it changed semantics to check the mode from
"xfrm[i]->props.mode != XFRM_MODE_TRANSPORT" to
"xfrm[i]->props.mode == XFRM_MODE_TUNNEL" before changing address.
It also makes two incline functions __xfrm6_bundle_addr_{remote,local}
are used by nobody.
This patch fixes it.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This last patch (but not least :) ) finally moves the next pointer at
the end of struct dst_entry. This permits to perform route cache
lookups with a minimal cost of one cache line per entry, instead of
two.
Both 32bits and 64bits platforms benefit from this new layout.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the next pointer from 'struct dn_route.u' union,
and renames u.rt_next to u.dst.dn_next.
It also moves 'struct flowi' right after 'struct dst_entry' to prepare
speedup lookups.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the next pointer from 'struct rt6_info.u' union,
and renames u.next to u.dst.rt6_next.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the rt_next pointer from 'struct rtable.u' union,
and renames u.rt_next to u.dst_rt_next.
It also moves 'struct flowi' right after 'struct dst_entry' to prepare
the gain on lookups.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces an anonymous union to nicely express the fact that all
objects inherited from struct dst_entry should access to the generic 'next'
pointer but with appropriate type verification.
This patch is a prereq before following patches.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a prior patch, I introduced a sk_hash field (__sk_common.skc_hash) to let
tcp lookups use one cache line per unmatched entry instead of two.
We can also use sk_hash to speedup UDP part as well. We store in sk_hash the
hnum value, and use sk->sk_hash (same cache line than 'next' pointer),
instead of inet->num (different cache line)
Note : We still have a false sharing problem for SMP machines, because
sock_hold(sock) dirties the cache line containing the 'next' pointer. Not
counting the udp_hash_lock rwlock. (did someone mentioned RCU ? :) )
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
