Patch from Richard Purdie
Update the PXA pm.c file to allow machines (such as the Sharp
Zaurus) to override the standard pm functions but reuse/wrap them
where needed.
The init call is made slightly earlier to give machine code an init
level to override them in removing any race.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Since we know the value of cpsr on entry, we can replace the bic+orr with
a single eor. Also remove a possible result delay (at least on XScale).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Make the uengine loader use ixp2000_reg_wrb in the right places.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch fixes AHB/PCI endianness problems when the
processor is in little-endian mode.
The patch configures the CSR register closely following the directives
in [1], paragraph 4.1, page 19.
According to the considerations in [1], page 11, while the AHB bus
supports both endian modes, on the IXP4XX it always uses big-endian.
The PCI bus is connected to the South AHB. A wrong setting in the CSR
register will thus cause a malfunctional PCI bus.
A schematic diagram of the bus interconnections on the IXP4XX
can be found in [1], page 18.
The patch has been verified to work on the NSLU2 in
both LE and BE modes.
The author is Peter Korsgaard.
[1] Intel® IXP4XX Product Line of Network Processors and IXC1100
Control Plane Processor:
Understanding Big Endian and Little Endian Modes
http://www.intel.com/design/network/applnots/25423701.pdf
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
We have an optimized sha1 routine (arch/arm/lib/sha1.S) meant to
override the generic one in lib/sha1.c.
Unfortunately lib/lib.a is listed _before_ arch/arm/lib/lib.a in the
link argument list and therefore the architecture specific lib functions
are not picked up before the generic versions.
This patch is a quick fix to change that ordering for ARM. Here's what
the kbuild maintainer had to say about it (was also CC'd on lkml):
On Wed, 2 Nov 2005, Sam Ravnborg wrote:
> This looks like an obvious way to achive correct ordering.
> We could change it so arch defines always took precedence but
> the above is so simple that it is not worth the effort.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dave Jiang
This provides support for IXP2xxx error interrupt handling. Previously there was a patch to remove this (although the original stuff was broken). Well, now the error bits are needed again. These are used extensively by the micro-engine drivers according to Deepak and also we will need it for the new EDAC code that Alan Cox is trying to push into the main kernel.
Re-submit of 3072/1, generated against git tree pulled today. AFAICT, this git tree pulled in all the ARM changes that's in arm.diff. Please let me know if there are additional changes. Thx!
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
ARM processors that have pld instructions are not using those copy_user
implementation anymore. Let's remove the useless PLD lines which were
half wrong anyway.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IXDP2401 config file has wrong baudrate and both boards have 3 UARTs.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Using a llx format to print addresses that might possibly be (only) 36
bits wide make sense. However making it a zero padded 16 char wide
field is a bit excessive and useless.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 'K' extension adds several new instructions to the ARMv6 ISA
which are primerily useful for SMP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
3016/1 changed the map_desc structure to take a PFN instead of a
physical address. Fixup Realview machine support for this change.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that without the extra tlb flush, we may end up faulting
during the early kernel initialisation because the TLB can't see
the updated page tables.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
CONFIG_MACH_GTWX5715 hardcodes the machine type in head-xscale.S so we
can no longer boot on any other machine types. The proper fix would be
to remove the hardcoding, but that machine is an off-the-shelf system
and most users won't have access to the bootloader. :(
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds a microcode loader for the ixp2000 architecture.
The ixp2000 is an xscale-based CPU with a number of additional small
CPUs ('microengines') on die that can be programmed to do various
things. Depending on the ixp2000 model, there are between 2 and 16
microengines.
This code provides an API that allows configuring the microengines,
loading code into them, and starting and stopping them and reading
out a number of status registers, and is used by the microengine
network driver that was recently announced to netdev.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch provides a preemption safe implementation of copy_to_user
and copy_from_user based on the copy template also used for memcpy.
It is enabled unconditionally when CONFIG_PREEMPT=y. Otherwise if the
configured architecture is not ARMv3 then it is enabled as well as it
gives better performances at least on StrongARM and XScale cores. If
ARMv3 is not too affected or if it doesn't matter too much then
uaccess.S could be removed altogether.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch provides a new implementation for optimized memory copy
functions on ARM. It is made of two levels: a template that consists of
the core copy code and separate files that define macros to be used with
the core code depending on the type of copy needed. This allows for best
performances while sharing the same core for implementing memcpy(),
copy_from_user() and copy_to_user() for instance.
Two reasons for this work:
1) the current copy_to_user/copy_from_user implementation assumes no
task switch will ever occur in the middle of each copied page making
it completely unsafe with CONFIG_PREEMPT=y.
2) current copy implementations are measurably suboptimal and optimizing
different implementations separately is a pain and more opportunities
for bugs.
The reason for (1) is the fact that copy inside user pages are performed
with the ldm instruction which has no mean for testing user protections
and could possibly race with process preemption bypassing the COW mechanism
for example. This is a longstanding issue that we said ought to be fixed
for about two years now. The solution is to substitute those ldm insns
with a series of ldrt or strt insns to enforce user memory protection.
At least on StrongARM and XScale cores the ldm is not faster than the
equivalent ldr/str insns with a warm i-cache so there is no measurable
performance degradation with that change. The fact that the copy code is
a template makes it pretty easy to reuse the same core code as for memcpy
and benefit from the same performance optimizations.
Now (2) is best demonstrated with actual throughput measurements.
First, here is a summary of memcopy tests performed on a StrongARM core:
PTR alignment buffer size kernel version this version
------------------------------------------------------------
aligned 32 59.73 107.43
unaligned 32 61.31 74.72
aligned 100 132.47 136.15
unaligned 100 103.84 123.76
aligned 4096 130.67 130.80
unaligned 4096 130.68 130.64
aligned 1048576 68.03 68.18
unaligned 1048576 68.03 68.18
The buffer size is in bytes and the measured speed in MB/s. The copy
was performed repeatedly with given buffer and throughput averaged over
3 seconds.
Here we can see that the current kernel version has a higher entry cost
that shows up with small buffers. As buffer size grows both implementation
converge to the same throughput.
Now here's the exact same test performed on an XScale core (PXA255):
PTR alignment buffer size kernel version this version
------------------------------------------------------------
aligned 32 46.99 77.58
unaligned 32 53.61 59.59
aligned 100 107.19 136.59
unaligned 100 83.61 97.58
aligned 4096 129.13 129.98
unaligned 4096 128.36 128.53
aligned 1048576 53.76 59.41
unaligned 1048576 33.67 56.96
Again we can see the entry setup cost being higher for the current kernel
before getting to the main copy loop. Then throughput results converge
as long as the buffer remains in the cache. Then the 1MB case shows more
differences probably due to better pld placement and/or less instruction
interlocks in this proposed implementation.
Disclaimer: The PXA system was running with slower clocks than the
StrongARM system so trying to infer any conclusion by comparing those
separate sets of results side by side would be completely inappropriate.
So... What this patch does is to replace both memcpy and memmove with
an implementation based on the provided copy code template. The memmove
code is kept separate since it is used only if the memory areas involved
do overlap in which case the code is a transposition of the template but
with the copy occurring in the opposite direction (trying to fit that
mode into the template turned it into a mess not worth it for memmove
alone). And obviously both memcpy and memmove were tested with all kinds
of pointer alignments and buffer sizes to exercise all code paths for
correctness.
The next patch will provide the now trivial replacement implementation
copy_to_user and copy_from_user.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Required for future enhancement patches.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
Lubbock updates:
* Provide an address for the SMC91x chip that doesn't generate
a boot-time warning (matching the EEPROM).
* Update MMC support to (a) detect card insert/remove, and
(b) report the readonly switch setting for SD cards.
Previously, MMC/SD cards had to be present at boot time else they
couldn't be detected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Platform data for the LCD/framebuffer driver for
the RX3715 LCD panel.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Switch the users of ixp2000_reg_write that depend on writes being
flushed out of the write buffer by the time that function returns
over to ixp2000_reg_wrb.
When using XCB=101, writes to the same functional unit are still
guaranteed to complete in order, so we only need to protect against:
- reordering of writes to different functional units
- masking an interrupt and then reenabling the IRQ bit in CPSR
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The enp2611 version of the ixp2000 netdev driver needs to be able to
access a number of on-board peripherals. ioremap() is not suitable
for this, as that will cause XCB=000 mappings to be done, which will
make the cpu susceptible to crashing on ixp2400 erratum #66. Properly
aligned iotable mappings with MT_IXP2000_DEVICE will cause section
mappings with XCB=101 to be done, which is safe.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IXDP2[48]00 have only 1 UART on the board.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch gets rid of the last C implementations of needed libgcc
functions for the kernel, replacing them with optimized assembly
versions.
Those functions are:
__ashldi3
__ashrdi3
__lshrdi3
__muldi3
__ucmpdi2
The first 3 were lifted from gcc, the other two were written from scratch.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Encapsulate pool data into dmabounce_pool. Only account successful
allocations. Use dma_mapping_error().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We know what pgprot we're going to use, so don't #define it. Also,
since we select the nonaliasing/aliasing copypage implementation at
run time, there's no point having it globally visible.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add spitz irda platform support
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add corgi irda platform support
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add poodle irda platform support
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Christoph Lameter demonstrated very poor scalability on the SGI 512-way, with
a many-threaded application which concurrently initializes different parts of
a large anonymous area.
This patch corrects that, by using a separate spinlock per page table page, to
guard the page table entries in that page, instead of using the mm's single
page_table_lock. (But even then, page_table_lock is still used to guard page
table allocation, and anon_vma allocation.)
In this implementation, the spinlock is tucked inside the struct page of the
page table page: with a BUILD_BUG_ON in case it overflows - which it would in
the case of 32-bit PA-RISC with spinlock debugging enabled.
Splitting the lock is not quite for free: another cacheline access. Ideally,
I suppose we would use split ptlock only for multi-threaded processes on
multi-cpu machines; but deciding that dynamically would have its own costs.
So for now enable it by config, at some number of cpus - since the Kconfig
language doesn't support inequalities, let preprocessor compare that with
NR_CPUS. But I don't think it's worth being user-configurable: for good
testing of both split and unsplit configs, split now at 4 cpus, and perhaps
change that to 8 later.
There is a benefit even for singly threaded processes: kswapd can be attacking
one part of the mm while another part is busy faulting.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prepare arm for the split page_table_lock: three issues.
Signal handling's preserve and restore of iwmmxt context currently involves
reading and writing that context to and from user space, while holding
page_table_lock to secure the user page(s) against kswapd. If we split the
lock, then the structure might span two pages, secured by to read into and
write from a kernel stack buffer, copying that out and in without locking (the
structure is 160 bytes in size, and here we're near the top of the kernel
stack). Or would the overhead be noticeable?
arm_syscall's cmpxchg emulation use pte_offset_map_lock, instead of
pte_offset_map and mm-wide page_table_lock; and strictly, it should now also
take mmap_sem before descending to pmd, to guard against another thread
munmapping, and the page table pulled out beneath this thread.
Updated two comments in fault-armv.c. adjust_pte is interesting, since its
modification of a pte in one part of the mm depends on the lock held when
calling update_mmu_cache for a pte in some other part of that mm. This can't
be done with a split page_table_lock (and we've already taken the lowest lock
in the hierarchy here): so we'll have to disable split on arm, unless
CONFIG_CPU_CACHE_VIPT to ensures adjust_pte never used.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_user_page_readable is a problematic variant of follow_page. It's used
only by oprofile's i386 and arm backtrace code, at interrupt time, to
establish whether a userspace stackframe is currently readable.
This is problematic, because we want to push the page_table_lock down inside
follow_page, and later split it; whereas oprofile is doing a spin_trylock on
it (in the i386 case, forgotten in the arm case), and needs that to pin
perhaps two pages spanned by the stackframe (which might be covered by
different locks when we split).
I think oprofile is going about this in the wrong way: it doesn't need to know
the area is readable (neither i386 nor arm uses read protection of user
pages), it doesn't need to pin the memory, it should simply
__copy_from_user_inatomic, and see if that succeeds or not. Sorry, but I've
not got around to devising the sparse __user annotations for this.
Then we can eliminate check_user_page_readable, and return to a single
follow_page without the __follow_page variants.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert those few architectures which are calling pud_alloc, pmd_alloc,
pte_alloc_map on a user mm, not to take the page_table_lock first, nor drop it
after. Each of these can continue to use pte_alloc_map, no need to change
over to pte_alloc_map_lock, they're neither racy nor swappable.
In the sparc64 io_remap_pfn_range, flush_tlb_range then falls outside of the
page_table_lock: that's okay, on sparc64 it's like flush_tlb_mm, and that has
always been called from outside of page_table_lock in dup_mmap.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
First step in pushing down the page_table_lock. init_mm.page_table_lock has
been used throughout the architectures (usually for ioremap): not to serialize
kernel address space allocation (that's usually vmlist_lock), but because
pud_alloc,pmd_alloc,pte_alloc_kernel expect caller holds it.
Reverse that: don't lock or unlock init_mm.page_table_lock in any of the
architectures; instead rely on pud_alloc,pmd_alloc,pte_alloc_kernel to take
and drop it when allocating a new one, to check lest a racing task already
did. Similarly no page_table_lock in vmalloc's map_vm_area.
Some temporary ugliness in __pud_alloc and __pmd_alloc: since they also handle
user mms, which are converted only by a later patch, for now they have to lock
differently according to whether or not it's init_mm.
If sources get muddled, there's a danger that an arch source taking
init_mm.page_table_lock will be mixed with common source also taking it (or
neither take it). So break the rules and make another change, which should
break the build for such a mismatch: remove the redundant mm arg from
pte_alloc_kernel (ppc64 scrapped its distinct ioremap_mm in 2.6.13).
Exceptions: arm26 used pte_alloc_kernel on user mm, now pte_alloc_map; ia64
used pte_alloc_map on init_mm, now pte_alloc_kernel; parisc had bad args to
pmd_alloc and pte_alloc_kernel in unused USE_HPPA_IOREMAP code; ppc64
map_io_page forgot to unlock on failure; ppc mmu_mapin_ram and ppc64 im_free
took page_table_lock for no good reason.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Nicolas Pitre
Since vmlinux.lds.S is preprocessed, we can use the defines already
present in asm/memory.h (allowed by patch #3060) for the XIP kernel link
address instead of relying on a duplicated Makefile hardcoded value, and
also get rid of its dependency on awk to handle it at the same time.
While at it let's clean XIP stuff even further and make things clearer
in head.S with a nice code reduction.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch allows for assorted type of cleanups by letting assembly code
use the same set of defines for constant values and avoid duplicated
definitions that might not always be in sync, or that might simply be
confusing due to the different names for the same thing.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Nicolas Pitre
Fix XIP support after recent bootmem code refactoring.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This got dropped from the SA1100 flash driver a while back and
never added to the platform support file. Add it back.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Bellido Nicolas
The AAED-2000 is equiped with an 640x480 LCD.
This adds the parameters that will be passed to the AAEC-2000 platform code.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
The AAEC-2000 has an ARM PrimeCell PL110 Color LCD Controller.
This patch contains the platform glue that will be used by specific boards.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Here is a preliminary clock interface support for the AAEC-2000.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
This adds platform code for MTD devices on AAEC-2000.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
The AAED-2000 board has GPIO pins on an external port.
This patch adds the defines, and do the necessary mapping.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This is the PXA2xx common IRDA driver, plus platform support
for Lubbock and Mainstone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
From: Daniel Jacobowitz <dan@debian.org>
> I also fixed a bug that confused me greatly while trying to debug: one
> SIGILL has long been a SIGSEGV because of some broken RISCOS
> compatibility code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add symbols for PXA2xx PWRMODE register M field that selects low-power
mode, replace unadorned constants. Honor power mode parameter of
pxa_cpu_suspend(mode), no longer force to 3 (sleep). Full Deep Sleep
low-power mode support for PXA27x is pending generic PM interfaces to
select more than 2 suspend-to-RAM-style power modes, but this is
expected soon. This can be hardcoded in the meantime by replacing the
pxa_cpu_suspend() parameter value. From David Burrage and Todd Poynor.
Try #2 removes one of the register copies and moves the code to save the
pxa_cpu_suspend parameter to immediately surround the call that requires
the parameter value be preserved.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
Updated 2898/1 per comments:
- Removed fixup
- Moved code in mach-mp1000/ to mach-clps711x/
- Cleaned up code in mp1000-seprom.c. Eliminated code that displayed the contents of the eeprom
Please comment.
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ian Campbell
As noted by Uli Luckas in the comments of 3025 there is a typo in the i2s platform device. The i2s platform device refers to the i2c resources.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add platform data for framebuffer for the
onboard LCD module
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add framebuffer platform data
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Change set_s3c2410fb_info to s3c2410_fb_set_platdata
and use kmalloc() for the copy of the information it
is passed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
From: Guillaume GOURAT <guillaume.gourat@nexvision.fr>
A number of devices have an extra byte on the
end of their areas due to mis-calculating the
.end field of their resources
Signed-off-by: Guillaume GOURAT <guillaume.gourat@nexvision.fr>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add generic values for the parameters to the
s3c2410_gpio_cfgpin() function, so that a caller
does not need to know the exact constant for
the specified pin.
This is very useful for the case where a driver
is passed a gpio pin number and needs to reconfigure
the pin's function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Here's an ARM assembly SHA1 implementation to replace the default C
version. It is approximately 50% faster than the generic C version. On
an XScale processor running at 400MHz:
generic C version: 9.8 MB/s
my version: 14.5 MB/s
This code is useful to quite a few callers in the tree:
crypto/sha1.c: sha_transform(sctx->state, sctx->buffer, temp);
crypto/sha1.c: sha_transform(sctx->state, &data[i], temp);
drivers/char/random.c: sha_transform(buf, (__u8 *)r->pool+i, buf + 5);
drivers/char/random.c: sha_transform(buf, (__u8 *)data, buf + 5);
net/ipv4/syncookies.c: sha_transform(tmp + 16, (__u8 *)tmp, tmp + 16 + 5);
Signed-off-by: Nicolas Pitre <nico@cam.org>
Seems to work fine on big-endian as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch adds support for 36-bit static mapped I/O. While there
are no platforms in the tree ATM that use it, it has been tested
tested on the IXP2350 NPU and I would like to get the support for
that chipset upstream one piece at a time. There are also other
Intel chipset ports in development that are waiting on this to go
upstream.
The patch replaces the print formats for physical addresses with
%016llx which will create a bit extraneous output on 32-bit systems,
but I think that is cleaner than having #ifdefs, specially since
users will only see the output in error cases.
Depends on 3016/1.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Convert map_desc.physical to map_desc.pfn. This allows us to add
support for 36-bit addressed physical devices in the static maps
without having to resort to u64 variables.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Integrator map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
iMX map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
H720x map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Footbridge map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
EBSA110 map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
EPXA10DB mapd_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Versatile map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
CLSP7500 map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
CLSP711x map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
SA1100 map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Shark map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
S3C2410 map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
RiscPC map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
PXA map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
OMAP map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
LH7A40x map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
IXP4xx map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
IXP2000 map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
IOP3xx map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
aaec2000 map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is nothing special about having the init code separate from
the common code, so combine the two.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The common oprofile code assumes the name "PMU" (from Intel's
performance management unit). This is misleading when we
start adding oprofile support for other machine types which
don't use the same terminology. Call it op_arm_* instead of
pmu_*.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The oprofile suspend/resume was missing locking. If we failed
to start oprofile on resume, we still reported that it was
enabled. Instead, disable oprofile on error.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make ARM independent of the way bootmem operates internally. We
now map each node as we initialise it, and place the bootmem bitmap
inside each node, rather than all in the first node.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse warnings in arch/arm/kernel/module.c,
arch/arm/mm/consistent.c, drivers/pcmcia/sa1111_generic.c,
and platform support files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
EBSA110 only requires hardware.h to be included for a couple of
files. Move the include there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes compile problem when CONFIG_FB_PXA is not set.
LD .tmp_vmlinux1
arch/arm/mach-pxa/built-in.o(.text+0x1d74): In function
`spitz_get_hsync_len':
: undefined reference to `pxafb_get_hsync_time'
make: *** [.tmp_vmlinux1] Error 1
3.46user 0.46system 5.10 (0m5.106s) elapsed 77.01%CPU
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The current Simtec BAST nand area timings are a little
too slow to be obtained by a 2410 running at 266MHz,
so reduce the timings slightly to bring them into the
acceptable range.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Matt Reimer
Adds an I2S platform_device for PXA. I2S is used to interface
with sound chips on systems like iPAQ h1910/h2200/hx4700 and
Asus 716.
Signed-off-by: mreimer@vpop.net
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Machine restart calls cpu_proc_fin() to clean and disable
cache, and turn off interrupts. This patch adds proper
cpu_v6_proc_fin.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Check that the device we are looking at is really
a platform device before trying to cast it to one
to find out the platform bus number.
Thanks to RMK for pointing this out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Remove a couple of lines of accidently added code causing compile
errors.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Update corgi_lcd to use bus_find_device to locate the pxafb device
hence fixing a compile error.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a function to allow machines to set the parent of the pxa
framebuffer device. This means the power up/down sequence can be
controlled where required by the machine.
Update spitz to use the new function, fixing a compile error.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch fixes L7200 so that it builds in 2.6.latest. I do not
have the hardware so don't know if it actually still works, but
the changes are fairly trivial. I am not even sure if anyone
still maintains, uses, or cares about this machine type.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
... and therefore should not live in the .text section.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The Simtec EB2410ITX (BAST) has a PC/104 slot, and
therefore we should enable CONFIG_ISA to allow the
drivers for ISA peripherals to be selected
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Remove an unused variable from s3c2410.c and
ensure that items not needed to be exported from
s3c2440.c are declared static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The NWFPE is producing a number of errors from sparse
due to not defining a number of functions in the
header files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
Fix leading, trailing and other miscellaneous whitespace issues
in arch/arm/kernel/alignment.c.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
When building for CPU_V6 targets, we should use -mtune=arm1136j-s rather
than -mtune=strongarm but fall back to the later in case someone is
using an older toolchain (although they should really upgrade instead).
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Do not export items that are not needed by symbol name
elsewhere
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The items in the export table do not need to be
exported elsehwere, so quash the sparse warning
by making the symbol for the table entry static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
arch/arm/mach-s3c2410/time.c is missing include
of cpu.h, causing the declaration of the timer
struct (s3c24xx_timer) to be flagged as missing
the declaration.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Either no one is using an ARM710 with recent kernels, or all ARM710s
still in use are not afflicted by this swi bug. Nevertheless, the code
to work around the ARM710 swi bug is itself currently buggy since it
uses r8 as a pointer to S_PC while in fact it holds the spsr content
these days. Fix that, and simplify the code as well.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Add a defconfig for the ARM Collie platform
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Add a defconfig for the ARM Corgi Zarus platform
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Add a defconfig for the ARM Poodle Zarus platform
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Add a defconfig for the ARM Spitz Zarus platform
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Allow the GPIO pin suspend states to be specified for SCOOP devices.
This is needed for correct operation on the spitz platform.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a missing include from corgi.c
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add some missing parameters from the scoop calls on collie.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
Add test for invalid LDRD/STRD Rd cases in ARM alignment handler
and restore SWP printk KERN_ERR.
Signed-off-by: Steve Longerbeam <slongerbeam@mvista.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
There is no reason to not allow these config options. They are useful when
the hardware has problems.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
If gcc decides to assign lr to %0 we're screwed.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The cmpxchg emulation syscall needs write access.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
Current implementation of imx_gpio_mode does not allow to
configure all alternate routing possibilities of the i.MX. With
this patch every bit in the gpio setup registers has a
corresponding bit in the gpio_mode parameter, so every routing
should be possible now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Data abort caused by ldrex/strex can leave the exclusive monitor in an
unpredictable state. It is recommended that a clrex/strex is performed to
clear this state.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
When building the fortunet ARM platform it fails to compile because of
missing include.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Serial port only needs 32 bytes of resource space but we are currently
asking for 64K.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
[ diff went missing first time due to corrupted patch ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Gen FUKATSU
Invalidate BTB entry instruction flushes two instruction
at a time. Therefore this instruction should be done four
times after invalidate instruction cache line.
Signed-off-by: Gen Fukatsu
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The warning is caused by the gic_set_cpu() function being defined but not
used if CONFIG_SMP is not defined.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
When CONFIG_CPU_CACHE_VIPT is defined, the flush_pfn_alias() function is
implicitely declared and it later conflicts with its actual definition.
This patch moves the function definition to the beginning of the file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since asm/hardware.h's only reason for existing is to include
asm/arch/hardware.h, it's completely pointless to include both.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix
arch/arm/mach-pxa/generic.c:242: warning: 'struct i2c_pxa_platform_data' declared inside parameter list
caused by missing asm/arch/i2c.h include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arm maketools needs include/asm-arm in place in the build tree.
On normal builds it's always there, of course, but on O= it's created
(by generic code) too late - when we get to asm-offset.h.
We used to get away with that by accident - creation of
include/asm-arm/arch symlink creates include/asm-arm and it happened
to go before maketools. However, we did not have such dependency,
so that luck didn't last - now maketools is picked first and we are screwed.
Both the symlink and maketools are prerequisites of the same
target (archprepare). This fix is obvious - make the latter explicitly
depend on the former and be done with that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Vincent Sanders
A recent patch which made IXP4xx mach_desc's depend on config options
had the effect of not building the kernel for several machines it
possibly could be, this patch updates the default config to ensure all
possible machines are built for by default.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We accidentally corrupted the TLS value when clearing out the ARMv6
exclusive monitor. Avoid doing so.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This patch prevents the "noreturn function does return" warning in the
__bug() function in arch/arm/kernel/traps.c
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per x86, we may deadlock while trying to get the mmap semaphore.
Implement the same fix, which allows (eg) recursive faults to cause
an oops instead of deadlocking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
This code is not being exported, declare it static
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the .arch.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the .proc.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the earlyparam
list is referencing items in the .init section as it is not itself
postfixed with .init
Also, as per rmk's suggestion, rename the __early_param to
.early_param to bring it into line with everything else
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Shark platform fails to build with gcc 4 because of a bad lvalue assignement
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the taglist
is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/arm/mach-sa1100/generic.c:224: warning: 'struct mcp_plat_data' declared inside parameter list
caused by mussing structure and function declaration.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Newer binutils complains:
/tmp/cc07pbI9.s:146: Warning: ignoring changed section type for .sched.text
Fix this warning by adding %progbits to the .section.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Building a kernel for IXDP425 currently includes the machine descriptors
for IXDP465 and PRPMC1100 even if those machines are not configured.
This means we can build a kernel that boots on those machines even
though the machine_is_xxx() macro will always return 0 and other bits
such as PCI won't be compiled in. This can lead to many wasted hours
wondering what you have done to your kernel to make it randomly crash
thus requireing large quantities of beer to be consumed. While I am
all for consumption of large quantities of beer, there are better
reasons to do so then stupid kernel bugs.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix up some pm_message_t types
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
This patch adds MMC and UDC support to the PXA Poodle platform.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch cleans up the PXA Poodle platform code removing an unneeded
static iomap. It also corrects errors in the platform header file and
adds a missing GPIO define.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch cleans up the PXA Corgi platform code removing an unneeded
static iomap, an unneeded function and some debug messages.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch adds a missing parameter to the scoop calls made by collie.c
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
It's silly to have I2C enabled in all ixp2000 defconfigs but not to
have the ixp2000 bus driver enabled in any of them. This patch enables
CONFIG_I2C_IXP2000 for all in-tree ixp2000 boards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This apparently fell in the crack somewhere. Add it back.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
As pointed out be Matthew Klahn <MKLAHN@motorola.com>, some sys_ipc()
call options require six args, e.g. SEMTIMEDOP. This patch adds an ARM sys_ipc_wrapper to save the sys_ipc() 'fifth' arg on the stack.
Signed-off-by: George G. Davis <gdavis@mvista.com>
arch/arm/kernel/calls.S | 2 +-
arch/arm/kernel/entry-common.S | 5 +++++
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the platform support code for two new Sharp Zaurus Models, Spitz
(SL-C3000) and Borzoi (SL-C3100).
This patch also adds most of the foundations for Akita (SL-C1000) Support.
The missing link for Akita is the driver for its I2C io expander. Once this
has been finished, the missing Kconfig option and machine declaration can
easily be added to this code.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
backlight driver. Abstract model/machine specific functions to corgi_lcd.c
via sharpsl.h
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
Touchscreen driver. Use the new functions in corgi_lcd.c via sharpsl.h for
hsync handling and pass the IRQ as a platform device resource. Move a
function prototype into the w100fb header file where it belongs.
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The same LCD is present on both the Sharp Zaurus c7x0 series and the cxx00 but
with different framebuffer drivers (w100fb vs. pxafb). This patch adds
support for the cxx00 series to the LCD driver. It also adds some LCD to
touchscreen interface logic needed by the touchscreen driver to prevent
interference problems, the idea being to keep all the ugly code in one place
leaving the drivers themselves clean. sharpsl.h is used to provide the
abstraction.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sharp's newer range of Zaurus clamshell handhelds, the cxx00's are similar to
the c7x0 series yet different. This patch series abstracts the differences
and generates a set of common drivers that support both series of devices. It
then adds machine support for Spitz (SL-C3000) and Borzoi (SL-C3100). Hooks
for Akita (SL-C1000) differences are also added. The I2C driver for its IO
expander is the only missing piece.
This patch:
Separate out the Sharp Zaurus c7x0 series specific code from corgi_ssp.c so
that other models such as the cxx00's can share it. Create sharpsl.h which
will be used to abstract machine/model specifics.
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When introducing the generic asm-offsets.h support the dependency
chain for the prepare targets was changed. All build scripts expecting
include/asm/asm-offsets.h to be made when using the prepare target would broke.
With the limited number of prepare targets left in arch Makefiles
the trivial solution was to introduce a new arch specific target: archprepare
The dependency chain looks like this now:
prepare
|
+--> prepare0
|
+--> archprepare
|
+--> scripts_basic
+--> prepare1
|
+---> prepare2
|
+--> prepare3
So prepare 3 is processed before prepare2 etc.
This guaantees that the asm symlink, version.h, scripts_basic
are all updated before archprepare is processed.
prepare0 which build the asm-offsets.h file will need the
actions performed by archprepare.
The head target is now named prepare, because users scripts will most
likely use that target, but prepare-all has been kept for compatibility.
Updated Documentation/kbuild/makefiles.txt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Randy cleaned out the bulk of these stale references to the now long gone
Documentation/smp.tex back in 2004. I followed this up with a few more
sweeps. Somehow, these have managed to sneak back in since.
I can't seem to figure out a contact point for M32R (no one listed in
MAINTAINERS!), but, these patches are only but trivial.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the final 20 DEFINE_SPINLOCK holdouts. (another 580 places
are already using DEFINE_SPINLOCK). Build tested on x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch add the plateform specific stuff needed to configure and use the
driver.
Signed-Off-By: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Dooks <ben@trinity.fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Fix a pm_message_t type warning in the Sharp scoop driver
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
We can remove this timer and its associated code from the corgi
platform code now mmc_detect_change() and the pxamci code support
an optional delay.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Updated the s3c2410_defconfig for the 2.6.13-git8
kernel release, as well as adding the Anubis
board to the list of boards built.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Convert more drivers to register resources in board-*.c to take
advantage of the driver model by David Brownell and Ladislav Michl
- Use set_irq_type() for GPIO interrupts instead of
omap_set_gpio_edge_ctrl() by David Brownell
- Add minimal support for handling optional add-on boards, such as
OSK Mistral board with LCD and keypad, by David Brownell
- Minimal support for loading functions to SRAM by Tony Lindgren
- Wake up from serial port by muxing RX lines temporarily into GPIO
interrupts by Tony Lindgren
- 32KHz sched_clock by Tony Lindgren and Juha Yrjola
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the necessary changes to ensure that we flush the
caches correctly with aliasing VIPT caches.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds low-level suspend/resume support to locomo.c.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sanitized and fixed floppy dependencies: split the messy dependencies for
BLK_DEV_FD by introducing a new symbol (ARCH_MAY_HAVE_PC_FDC), making
BLK_DEV_FD depend on that one and taking declarations of ARCH_MAY_HAVE_PC_FDC
to arch/*/Kconfig. While we are at it, fixed several obvious cases when
BLK_DEV_FD should have been excluded (architectures lacking asm/floppy.h
are *not* going to have floppy.c compile, let alone work).
If you can come up with better name for that ("this architecture might
have working PC-compatible floppy disk controller"), you are more than
welcome - just s/ARCH_MAY_HAVE_PC_FDC/your_prefered_name/g in the patch
below...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add keyboard and touchscreen device definitions for corgi.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the platform specific Sharp SL-C7x0 LCD code from the
w100fb driver into a more appropriate place and updates the Corgi code to
match the new w100fb driver.
It also updates the corgi touchscreen code to match the new simplified
interface available from w100fb.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch cleans up a commonly repeated set of changes to the NTP state
variables by adding two helper inline functions:
ntp_clear(): Clears the ntp state variables
ntp_synced(): Returns 1 if the system is synced with a time server.
This was compile tested for alpha, arm, i386, x86-64, ppc64, s390, sparc,
sparc64.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
This has been broken for a while now, so fix the
problems with the code, test and bring up to date.
This also makes the code conditional on an
Kconfig option
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Adam Brooks
The current gettimeofday implementation for the IOP3xx processors reads the contents of the timer interrupt register and does math on the value to figure out exactly what time it is. To do this it multiplies the contents of the timer register with a large constant. The result is then divided by a large constant. Unfortunately the result of the first multiplication is often too large for the register to hold. The solution is to combine the two large constants to a single smaller constant at compile time. Then the timer value can be divided by single smaller constant without any overflow issues.
Signed-off-by: Adam Brooks <adam.j.brooks@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add machine detection routines for several new models of PXA based Zaurii
(SL-C3000 - Spitz, SL-C1000 - Akita, SL-C3100 - Borzoi, SL-C6000 - Tosa).
Sharp continue to use broken bootloaders in ROM.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch updates H2 defconfig
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Clock updates by Tuukka Tikkanen, Juha Yrjola,
Daniel Petrini and Tony Lindgren
- DMA fixes by Imre Deak, Juha Yrjola and Daniel Petrini
- Add support to dual-mode hardware timers by Lauri Leukkunen
- GPIO support for 24xx by Paul Mundt
- GPIO wake-up support by Tony Lindgren
- Better GPIO interrupt handler to not lose interrupts by
Ralph Walden and Ladislav Michl
- Power Management updates by Tuukka Tikkanen
- Make Power Management code use new SRAM functions by
Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add the Simtec Anubis to the list of supported
machines in the arch/arm/mach-s3c2410 directory.
This ensures the core peripherals are registered,
the timer source is configured and the correct
power-management is enabled.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch updates the PCMCIA pxa2xx_sharpsl driver to support multiple scoop
devices by adding a scoop to pcmcia slot mapping structure. It adds platform
support for poodle, is known to work on spitz (which is dual slot) and
should also support collie with a minor amount of further work.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The n30 machine file is using a kernel thread to change the
state of the USB D+ pull-up resistor, which is not the proper
way to do this. Once the usb-gadget support for the 24xx is
merge, the proper access method will be added.
This patch also removes the problem of using HZ for the
msleep calls, from Nishanth Aravamudan.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is part of Thomas Gleixner's generic IRQ patch, which converts
ARM to use the generic IRQ subsystem. Here, we wrap calls to
desc->handler() in an inline function, desc_handle_irq(). This
reduces the size of Thomas' patch since the changes become more
localised.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is part of Thomas Gleixner's generic IRQ patch, which converts
ARM to use the generic IRQ subsystem. Here, we rename two of the
irq_chip methods - wake becomes set_wake, and type becomes set_type.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do not access children in struct device directly, use
device_for_each_child helper instead. It fixes compilation.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Timothy Baldwin
All data aborts are treated as read accesses. The existing code updates the wrong bit of r1, also the comments are wrong in that the sense of the L bit is inverted.
Signed-off-by: Timothy E. Baldwin <T.E.Baldwin99@members.leeds.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The power management sleep code needs to call cpu_init()
to restore the cpu state after the system resumes from
suspend. Also clear off an un-necessary comment.
Thanks to Dimitry Andric for reporting the bug and
for rmk for pointing out the cause.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We weren't explicitly setting the page table bits we desired
in user_prot in the protection table, which resulted in the
user mappings for v6 CPUs being marked global.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No point checking what CPU architecture level we have each time
within the loop, so precompute the base PMD flags outside the
loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The prototype for sys_fadvise64_64() is:
long sys_fadvise64_64(int fd, loff_t offset, loff_t len, int advice)
The argument list is therefore as follows on legacy ABI:
fd: type int (r0)
offset: type long long (r1-r2)
len: type long long (r3-sp[0])
advice: type int (sp[4])
With EABI this becomes:
fd: type int (r0)
offset: type long long (r2-r3)
len: type long long (sp[0]-sp[4])
advice: type int (sp[8])
Not only do we have ABI differences here, but the EABI version requires
one additional word on the syscall stack.
To avoid the ABI mismatch and the extra stack space required with EABI
this syscall is now defined with a different argument ordering
on ARM as follows:
long sys_arm_fadvise64_64(int fd, int advice, loff_t offset, loff_t len)
This gives us the following ABI independent argument distribution:
fd: type int (r0)
advice: type int (r1)
offset: type long long (r2-r3)
len: type long long (sp[0]-sp[4])
Now, since the syscall entry code takes care of 5 registers only by
default including the store of r4 to the stack, we need a wrapper to
store r5 to the stack as well. Because that wrapper was missing and was
always required this means that sys_fadvise64_64 never worked on ARM and
therefore we can safely reuse its syscall number for our new
sys_arm_fadvise64_64 interface.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Minor compilation error fix.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Steve Longerbeam
Adds an implementation of unaligned LDRD and STRD fixups.
Also fixes a bug where do_alignment() would misinterpret and
fixup an unaligned LDRD/STRD as LDRH/STRH, causing memory
corruption.
This is the same as Patch #2867/1, but with minor whitespace
and comments changes, plus a check for arch-level >= v5TE
before printing ai_dword count in proc_alignment_read().
Signed-off-by: Steve Longerbeam <stevel@mwwireless.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
timer_dyn_reprogram() fails with an OOPS if the
configuration for CONFIG_NO_IDLE_HZ is enabled, and
the system has no support for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Working on adding support for 36-bit static mappings for ARMv6 and
Intel's XSC3 core and noticed that alloc_init_supersection currently
increments the phys addr by 1MB on each of the 16 iterations and then
forces alignment to supersection size (16MB). This is really uneeded
b/c we have already forced the phys address to be 16MB aligned in
create_mapping(). Furthermore, this breaks 36-bit addressing b/c bits
[23:20] of the PMD contain bits [35:32] of the physical address and
the masking causes us to loose those bits thus ending up with an
incorrect virt -> phys translation. The other option is to have an
alloc_init_supersection36.
Tested on Intel IXP2350 CPU with 36-bit static I/O mappings.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Show the state of DVS (Dynamic Voltage Scaling) when
starting up on the S3C2440
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add the definitions for the S3C2410_CLKSLOW registers to
the header files, and show the values when the system
starts up
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch implements the set_irq_type() hooks for configuring GPIO
IRQ type and updates all the platforms to use it instead of the
gpio_line_config() function which is now used to configure input
vs. output on the pins.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
None of the board-specific map_io routines do anything, so kill them.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This kills i386-specific stuff from arm Kconfig. Please apply,
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are currently reserving one byte more than actually needed by the flash
device and overlapping into the next I/O expansion bus window. This a)
causes us to allocate an extra page of VM due to ARM ioremap() alignment
code and b) could cause problems if another driver tries to request the
next expansion bus window.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
a bunch of functions switched from volatile to __attribute__((noreturn)) and
from const to __attribute_pure__
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add platform device data for the SA11x0 MCP device. This allows
platforms to customise the configuration of the SA11x0 MCP device
according to their needs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the core of the multimedia communication port
framework. This is a port used to communicate with devices
with two DMA paths and a control path.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dimitry Andric
This patch removes the initial UART I/O mapping from s3c2410_iodesc,
since the same mapping is already done in the function s3c24xx_init_io
in the file arch/arm/mach-s3c2410/cpu.c, through the s3c_iodesc array.
I'm not sure if duplicate mappings do any harm, but it's simply
redundant. Also, in s3c2440.c the UART I/O mapping is NOT done.
Additionally, I put a comma behind the last mapping, to ease
copy/pasting stuff around, and make the style consistent with
s3c2440.c and other files.
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sean Lee
In the arch/arm/mm/Kconfig file, the CPU_DCACHE_WRITETHROUGH
option is depend on the CPU_DISABLE_DCACHE, but the "Disable
D-Cache" option is configured as CPU_DCACHE_DISABLE.
The CPU_DISABLE_DCACHE should be CPU_DCACHE_DISABLE
Signed-off-by: Sean Lee <beginner2arm@eyou.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The exception handling code fails to compile if the extended
precision mode is enabled. This patch fixes those compile errors and
also stops _quiet functions from incorrectly raising exceptions.
Reported-by: Ralph Siemsen <ralphs@netwinder.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Rename the s3c2410_report_oc() to s3c2410_usb_report_oc()
as this is an usb specific function.
Change port power on the usb-simtec implementation to only
power up the output if both are set, as per the usb 1.1
specification
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, we can't use the "user" bit in the page tables to
control whether a page table entry is "global" or "asid" specific,
since the vector page is mapped as "user" accessible but is not
process specific.
Therefore, give direct control of the ARMv6 "nG" (not global)
bit to the mm layers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In yenta_socket, we default to using the resource setting of the CardBus
bridge. However, this is a PCI-bus-centric view of resources and thus needs
to be converted to generic resources first. Therefore, add a call to
pcibios_bus_to_resource() call in between. This function is a mere wrapper on
x86 and friends, however on some others it already exists, is added in this
patch (alpha, arm, ppc, ppc64) or still needs to be provided (parisc -- where
is its pcibios_resource_to_bus() ?).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Michael Gernoth
As discussed on the handhelds.org Jornada mailinglist, I take over
maintainership of the currently unmaintained Jornada 720-port in
the mainline kernel.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Fix a typo causing a warning in the arm oprofile backtrace code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM fault handler is optimised to make the fast path, err, fast.
The renumbering of the VM_FAULT_* codes broke this because numbers
were used instead of the definitions. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This allows the serial driver autconf to work properly on all the IXP
serial ports. W/o it we basically put the serial port in an unrecoverable
state and lose console.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The IEEE 754 standard specifies that the result of (x - x), where x is
a valid number, should be -0 if the rounding mode is towards minus
infinity or +0 otherwise.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
The XScale locking code is not something that has been validated
on 2.6 and needs to be replaced with a more generic API to use
with other ARMs that support locking features.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
NWFPE used global variables which meant it wasn't safe for use with
preemptive kernels. This patch removes them and communicates the
information between functions in a preempt safe manner. Generation
of some exceptions was broken and this has also been corrected.
Tests with glibc's maths test suite show no change in the results
before/after this patch.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The default clock rate does not specify a maximum, so the
default of 400KHz is used. This rate is too fast for the PMU
on the EB2410ITX, so we now specify platform data with a rate
of around 100KHz.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the secondary CPUs will not be operating in symetric mode
while they are held in the pen, we need to ensure that the write
to pen_release is visible to them, by flushing the cache.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We sometimes forgot to check whether the exclusive store succeeded.
Ensure that we always check. Also ensure that we always use the
out of line versions, since the inline versions are not SMP safe.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since ARMv6 CPUs will not flush the TLB on context switches, it is
possible that we may end up with some global TLB entries remaining
present, eventually upsetting userspace. Explicitly flush the
entire TLB on secondary CPUs as they startup, after we have switched
to the init_mm page tables.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we found that the bit was already in the desired state, we
would skip performing the operation, and write random data back.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Split the s3c2440 specific clocks from the arch clock support, to
make the code clearer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
machine_restart, machine_halt and machine_power_off are machine
specific hooks deep into the reboot logic, that modules
have no business messing with. Usually code should be calling
kernel_restart, kernel_halt, kernel_power_off, or
emergency_restart. So don't export machine_restart,
machine_halt, and machine_power_off so we can catch buggy users.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ARMv6 introduces memory types into the page tables. Mark devices
mappings with the "shared device" memory type.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Remove the need for the #ifdefs and place the IRQ handling code for
the s3c2440 into a new file, which is only compiled when the
s3c2440 cpu support is enabled.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
There is no point in mapping this staticaly, the driver is going
to ioremap() the area as it sees fit. Also correct the dates on
the changelog comments
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch replaces the sizeof()'s %d specifier by %ld on a S3C2410 DMA
printk.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Use platform device for the 16500 UARTs in the onboard
SuperIO controller.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alexander Schulz
Up to now, shark kernels were limited to one megabyte compressed
size. As the kernels get bigger, this becomes more and more
uncomfortable. So I added a loop to copy 3 MB instead of one
and added some comments.
Signed-off-by: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent changes to nwfpe broke the build with some gcc versions:
In file included from arch/arm/nwfpe/softfloat.c:33:
arch/arm/nwfpe/fpa11.h:32: global register variable follows a function definition
make[1]: *** [arch/arm/nwfpe/softfloat.o] Error 1
Since we now ensure that the kernel stack is empty when returning
to user space, we can now access the userspace registers with
reference to the kernel stack using current_thread_info(), rather
than remembering the stack pointer at the time nwfpe was called.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alexander Schulz
This patch brings a new default config file for the shark and
fixes a compilation issue with io addressing and a runtime
problem with the serial ports, where I corrected a wrong
regshift value.
These are all shark specific files so I hope it is ok to
put them in one patch.
Signed-off-by: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Preserve the interrupt status across a call to register_undef_hook.
This allows it to be called while interrupts are disabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>