The link state event calls were being generated when the SM told the SMA
to change link states. This works for IB_EVENT_PORT_ACTIVE but not if
the link goes down and stays down. The fix is to generate event calls
from the interrupt handler when the HW link state changes.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The General Purpose I/O pins can be configured to cause interrupts. At
the end of the interrupt code dealing with all known causes, a message
is output if any bits remain un-handled. Since this is a "can't happen"
scenario, it should only be triggered by bugs elsewhere. It is harmless,
and potentially beneficial, to limit the damage by masking any such
unexpected interrupts.
This patch adds disabling of interrupts from any pins that should
not have been allowed to interrupt, in addition to emitting a message.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a count of "active hours" maintained in EEPROM, to aid
troubleshooting. The definition of "active" is based on traffic
exceeding a threshold in any given 5-second polling interval. As
originally written, the check was inadvertently bypassed for chips whose
counters were 64-bits wide, and only applied to chips with 32-bit wide
counters.
This patch moves the test for amount of traffic "out" to a more common
location, rather than depending on a side-effect of the software
emulation of 64-bit counts on chips whose hardware is only 32-bits wide.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove all the OEM and bringup boards, and complain and fail
initialization if one is found. QHT7040 with GPIO rework (128ywwuuuu)
is OK, older 112ywwuuuu is no longer supported). The check that had been
added was failing both the 112 and 128 series.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A couple of chip bugs in the iba6110 and in the iba6120 are not in more
recent chips. This first bug swaps two of the pioavail register
locations. In the second bug, the chip can sometimes forget to dma the
pio avail register to memory. We indicate the presence of these bugs
with runtime flags and we indicate the presence of the flags by bumping
the SWMINOR.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iba6110 rev3 and earlier had a chip bug where the chip could overrun the
recv header queue. rev4 fixed this chip bug so userspace no longer needs
to workaround it. Now we only set the workaround flag for older chip
versions.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_poll() suffered from a couple subtle bugs. Under the right
conditions we could leave recv interrupts enabled on an ipath user
context on close, thereby taking potentially unwanted interrupts on the
next open -- this is fixed by unconditionally turning off recv
interrupts on close. Also, we now use counters rather than set/clear
bits which allows us to make sure we catch all interrupts at the cost of
changing the semantics slightly (it's now give me all events since the
last time I called poll() rather than give me all events since I called
_this_ poll routine). We also added some memory barriers which may help
ensure we get all notifications in a timely manner.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The LMC value was being saved by the SMA in two places. This patch
cleans it up so only one copy is kept.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds the ability to set the LMC via a sysfs file as if the SM
sent a SubnSet(PortInfo) MAD. It is useful for debugging when no SM is
running.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to add an entry to the completion queue stored the QPN which is
needed for the user level verbs view of the completion queue entry but
the kernel struct ib_wc contains a pointer to the QP instead of a QPN.
When the kernel polled for a completion queue entry, the QPN was lookup
up and the QP pointer recovered. This patch stores the CQE differently
based on whether the CQ is a kernel CQ or a user CQ thus avoiding the
QPN to QP lookup overhead.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch implements the IB_EVENT_QP_LAST_WQE_REACHED event which is
needed by ib_ipoib to destroy the QP when used in connected mode.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Follow the IB spec. (C10-96) for post send which states that a flushed
completion event should be generated for work requests posted when a QP
is in the error state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch removes some redundant initialization code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In an earlier change, the amount of data read from the flash was
mistakenly limited to the size known to the current driver. This causes
problems when the length is increased, and written with the new longer
version; the checksum would fail because not enough data was read.
Always read the full 128 byte length to prevent this.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a bug in the receive processing for UC RDMA WRITE with
immediate which caused the last packet to be dropped.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a comment change, only, correcting the comment to match the
implemented workaround, rather than the original workaround, and
clarifying why it's needed.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipathfs file system is used to export binary data verses ASCII data
such as through /sys. This patch removes some unneeded files since the
data is available through other /sys files.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There have been a number of issues where host bandwidth via HT or PCIe
to the InfiniPath chip has been limited in some fashion (BIOS,
configuration, etc.), resulting in user confusion. This check gives a
clear warning that something is wrong and needs to be resolved.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to post UD sends tried to process work requests at the time
ib_post_send() is called without using a WQE queue. This was fine as
long as HW resources were available for sending a packet. This patch
changes UD to be handled more like RC and UC and shares more code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different processors have different ordering restrictions for write
combining. By taking advantage of this, we can eliminate some write
barriers when writing to the send buffers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On iba6110 rev4, support for three more IB counters were added. The
LocalLinkIntegrityError counter, the ExcessiveBufferOverrunErrors
counter and support for error counting of flow control packets on an
invalid VL. These counters trigger GPIO interrupts and the sw keeps
track of the counts. Since we also use GPIO interrupts to signal packet
reception, we need to turn off the fast interrupts, or we risk losing a
GPIO interrupt.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Doing min_t(int, foo, INT_MAX) doesn't work correctly, because if foo
is bigger than INT_MAX, then when treated as a signed integer, it will
become negative and hence such an expression is just an elaborate NOP.
Fix such cases in ehca to do min_t(unsigned, foo, INT_MAX) instead.
This fixes negative reported values for max_cqe, max_pd and max_ah:
Before:
max_cqe: -64
max_pd: -1
max_ah: -1
After:
max_cqe: 2147483647
max_pd: 2147483647
max_ah: 2147483647
Based on a bug report and fix from Anton Blanchard <anton@samba.org>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the way QP is being created in ipoib_cm_create_tx_qp()
consistent with ipoib_cm_create_rx_qp().
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Firmware commands are sent to the HCA by writing multiple words to a
command register block. Access to this block of registers is
serialized with a mutex. However, on large SGI systems, problems were
seen with multiple CPUs issuing FW commands at the same time, because
the writes to the register block may be reordered within the system
interconnect and reach the HCA in a different order than they were
issued (even with the mutex). Fix this by adding an mmiowb() before
dropping the mutex.
Tested-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Automatically queue MRA message to decrease the number of retries sent
by the remote side during connection establishment. This also has the
effect of increasing the overall connection timeout without using a
longer retry time in the case of dropped packets.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB CM provides a message received acknowledged (MRA) message that
can be sent to indicate that a REQ or REP message has been received, but
will require more time to process than the timeout specified by those
messages. In many cases, the application may not know how long it will
take to respond to a CM message, but the majority of the time, it will
usually respond before a retry has been sent. Rather than sending an
MRA in response to all messages just to handle the case where a longer
timeout is needed, it is more efficient to queue the MRA for sending in
case a duplicate message is received.
This avoids sending an MRA when it is not needed, but limits the number
of times that a REQ or REP will be resent. It also provides for a
simpler implementation than generating the MRA based on a timer event.
(That is, trying to send the MRA after receiving the first REQ or REP if
a response has not been generated, so that it is received at the remote
side before a duplicate REQ or REP has been received)
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Increase the number of QPs allowed per multicast group from 8 to 56.
This allows for one QP per core on 16-core systems, which are now
quite common, and allows some space for future growth.
This is basically the same patch that Jack Morgenstein
<jackm@dev.mellanox.co.il> just supplied for mlx4.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement FMRs for mlx4. This is an adaptation of code from mthca.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Write MTT entries directly to ICM from the driver (eliminating use of
WRITE_MTT command). This reduces the number of FW commands needed to
register an MR by at least a factor of 2 and speeds up memory
registration significantly. This code will also be used to implement
FMRs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_uverbs_release_event_file() is only used in uverbs_main.c, so make it
static to that file. Also move the definition before the first use, so
a forward declaration is not needed.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The declaration of struct ib_user_mad_reg_req.method_mask[] exported
to userspace was an array of __u32, but the kernel internally treated
it as a bitmap made up of longs. This makes a difference for 64-bit
big-endian kernels, where numbering the bits in an array of__u32 gives:
|31.....0|63....31|95....64|127...96|
while numbering the bits in an array of longs gives:
|63..............0|127............64|
64-bit userspace can handle this by just treating method_mask[] as an
array of longs, but 32-bit userspace is really stuck: the meaning of
the bits in method_mask[] depends on whether the kernel is 32-bit or
64-bit, and there's no sane way for userspace to know that.
Fix this by updating <rdma/ib_user_mad.h> to make it clear that
method_mask[] is an array of longs, and using a compat_ioctl method to
convert to an array of 64-bit longs to handle the 32-on-64 problem.
This fixes the interface description to match existing behavior (so
working binaries continue to work) in almost all situations, and gives
consistent semantics in the case of 32-bit userspace that can run on
either a 32-bit or 64-bit kernel, so that the same binary can work for
both 32-on-32 and 32-on-64 systems.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for setting the P_Key index of sent MADs and getting the
P_Key index of received MADs. This requires a change to the layout of
the ABI structure struct ib_user_mad_hdr, so to avoid breaking
compatibility, we default to the old (unchanged) ABI and add a new
ioctl IB_USER_MAD_ENABLE_PKEY that allows applications that are aware
of the new ABI to opt into using it.
We plan on switching to the new ABI by default in a year or so, and
this patch adds a warning that is printed when an application uses the
old ABI, to push people towards converting to the new ABI.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Hal Rosenstock <hal@xsigo.com>
display the following device information under /sys/class/infiniband/mlx4_X:
board_id, fw_ver, hw_rev, hca_type.
This patch makes this information available to userspace utilities
such as ibstat and ibv_devinfo.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I was looking at the code for multicast.c and noticed that
ib_sa_join_multicast() calls queue_join() which puts the
request at the front of the group->pending_list. If this
is a second request, it seems like it would interfere with
process_join_error() since group->last_join won't point
to the member at the head of the pending_list. The sequence
would thus be:
1. ib_sa_join_multicast()
puts member1 on head of pending_list and starts work thread
2. mcast_work_handler()
calls send_join() which sets group->last_join to member1
3. ib_sa_join_multicast()
puts member2 on head of pending_list
4. join operation for member1 receives failures response from SA.
5. join_handler() is called with error status
6. process_join_error() fails to process member1 since
it doesn't match the first entry in the group->pending_list.
The impact is that the failed join request is tossed. The second
request is processed, and after it completes, the original request ends
up being retried.
This change also results in join requests being processed in FIFO
order.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* Replace {un}register_cpu_notifier with {un}register_hotcpu_notifier
thereby losing a couple of #ifdef HOTPLUG_CPU pairs.
* Move comp_pool_callback_nb declaration to below that of callback
function so that initialization of .notifier_call and .priority can
occur at build time itself and not runtime.
* Mark the notifier_block (and callback function, and another static
function used by it) as __cpuinit{data} for the sake of consistency
and remove enclosing #ifdef. (This may increase size for modular
build of this module, however, because these are no longer dropped
unconditionally now.)
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
<asm/scatterlist.h> is not needed because everyplace it appears,
<linux/scatterlist.h> also appears. <asm/io.h> is not needed because
nothing seems to be using device IO anyway.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Calling arp_send() to initiate neighbour discovery (ND) doesn't do the
full ND protocol. Namely, it doesn't handle retransmitting the arp
request if it is dropped. The function neigh_event_send() does all
this. Without doing full ND, RDMA address resolution fails in the
presence of dropped ARP broadcast packets.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
...because, on virtualized hardware like System p, we can't be sure
that the physical pages behind them are contiguous otherwise.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During ib_umem_get(), determine whether all pages from the memory
region are hugetlb pages and report this in the "hugetlb" member.
Low-level drivers can use this information if they need it.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide the target service ID when performing a path record query to
support optional QoS capability. QoS requires support from the SA.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export the ability to set the type of service to user space. Model
the interface after setsockopt.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide support to specify a type of service for a communication
identifier. A new function call is used when dealing with IPv4
addresses. For IPv6 addresses, the ToS is specified through the
traffic class field in the sockaddr_in6 structure.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
[ The comments Eitan Zahavi and myself have made over the v1 post at
<http://lists.openfabrics.org/pipermail/general/2007-August/039247.html>
were fully addressed. ]
Reviewed-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The QoS annex defines new fields for path records. Add them to the
ib_sa for consumers that want to use them.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can use raw_smp_processor_id() here because the processor ID is
only used for debug output and therefore our use is preemption-unsafe.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some firmware levels exhibit a race condition between H_ALLOC_RESOURCE(MR)
and H_FREE_RESOURCE(MR). Work around this problem by locking these hvCalls
against each other.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix some modify_qp() issues related to path migration.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change hvcall trace output towards better readability: reg numbers
instead of argument numbers, return code as signed decimal instead of
unsigned hex.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use Paul's new remap_4k_pfn() function to map our 4K firmware contexts
into user space on 64K-page machines without exposing neighboring
firmware contexts. Return the context's offset within a 64K page to
user space so it can determine the proper virtual address.
For details about remap_4k_pfn(), see commit 721151d0 or
http://patchwork.ozlabs.org/linuxppc/patch?id=10281
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
These driver changes incorporate the proposed PCI-X / PCI-Express read
byte count interface. Reading and setting those values doesn't take
place "manually", instead wrapping functions are called to allow
quirks for some PCI bridges.
Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_create_send_mad() returns an error code pointer on error, not NULL.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At the moment the ehca module parameters are not exported in sysfs.
Export them with 0444 permissions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ehca spits out a lot of debugging information. I had to look closely to
see the "Port 1 is not active" message within all the debug:
eHCA Infiniband Device Driver (Rel.: SVNEHCA_0022)
eHCA scaling code enabled
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_define_sqp Port 1 is not active.
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_create_qp ehca_define_sqp() failed rc=ffffffffffffffff
ib_mad: Couldn't create ib_mad QP1
ib_mad: Couldn't open ehca0 port 1
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr unsupported fmr_attr->page_shift=9
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr rc=ffffffffffffffea pd=c000000b4b5b2420 mr_access_flags=7 fmr_attr=c0000005afd37394
fmr_create failed for FMR 0
Remove a few debug statements so that things are clearer:
eHCA Infiniband Device Driver (Rel.: SVNEHCA_0022)
eHCA scaling code enabled
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_define_sqp Port 1 is not active.
ib_mad: Couldn't create ib_mad QP1
ib_mad: Couldn't open ehca0 port 1
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr unsupported fmr_attr->page_shift=9
fmr_create failed for FMR 0
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_srq_query() returns a big-endian 16-bit value through an int *,
which screws up sparse checking. Fix this so that a CPU-endian value
is returned.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up properly if ib_query_pkey() or ib_query_gid() fail.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recover from MSI-X errors by automatically falling back on regular
interrupt, instead of asking the user to do this manually. This makes
it possible to enable MSI-X by default, and will make it possible to
get rid of the msi_x module option in the future.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A number of printks in fmr_pool.c dont have newlines, eg:
fmr_create failed for FMR 0<5>FS-Cache: Loaded
Fix them up.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ehca_classes.h uses struct mutex, so while <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include <linux/mutex.h> directly.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Acked-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use a __set_data_seg() helper in mlx4_ib_post_recv() too; in addition
to making the code easier to read, this also allows gcc to generate
better code -- on x86_64:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function old new delta
mlx4_ib_post_recv 359 351 -8
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix sparse warning
drivers/infiniband/core/device.c:142:6: warning: incorrect type in argument 1 (different signedness)
drivers/infiniband/core/device.c:142:6: expected unsigned long const *addr
drivers/infiniband/core/device.c:142:6: got long *[assigned] inuse
by making the local variable inuse unsigned. Does not affect generated
code at all.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current IPoIB code might process receive completions from
ipoib_drain_cq() when bringing down the interface. This could cause
packets to be passed up the stack without the device's poll method
being called. Avoid this by setting the status of any successful
completions to IB_WC_WR_FLUSH_ERR.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow changing parameter values without having to reload the module.
This is safe because these parameters are only looked at when a new
connection is established.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is an addendum to commit 0e6e7416 ("IB/mlx4: Handle new FW
requirement for send request prefetching"). We also need to handle
prefetch marking properly for S/G segments, or else the HCA may end up
processing S/G segments that are not fully written and end up sending
the wrong data. This can actually cause data corruption in practice,
especially on systems with relatively slow CPUs (where the HCA is more
likely to prefetch while the CPU is in the middle of writing a work
request into memory).
We write S/G segments in reverse order into the WQE, in order to
guarantee that the first dword of all cachelines containing S/G
segments is written last (overwriting the headroom invalidation
pattern). The entire cacheline will thus contain valid data when the
invalidation pattern is overwritten.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: SRQ fixes to enable IPoIB CM
IB/ehca: Fix Small QP regressions
Fix ehca SRQ support so that IPoIB connected mode works:
- Report max_srq > 0 if SRQ is supported
- Report "last wqe reached" asynchronous event when base QP dies;
this is required by the IB spec and IPoIB CM relies on receiving it
when cleaning up.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new Small QP code had a few bugs that would also make it trigger
for non-Small QPs. Fix them.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.
Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A stray semicolon makes us inadvertently ignore the value of err.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_transport_dev_init() calls ipoib_cm_dev_init(), so it needs to
call ipoib_cm_dev_cleanup() to unwind that on the error path.
Found by Dotan Barak of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code has a cut-and-paste error and returns IB_WC_SEND when it
should return IB_WC_RDMA_READ.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New Cisco IB SRP targets use the Cisco OUI 00-1b-0d but still need the
Topspin workarounds. Add this OUI to srp_target_is_topspin().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrap the checking for Mellanox and Topspin OUIs to decide whether to
use a workaround into helper functions. This will make it cleaner to
add a new OUI to check (as we need to do now that some targets with a
Cisco OUI still need the Topspin workarounds).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After moving the definition of struct ib_umem_chunk from ib_verbs.h to
ib_umem.h there isn't any reason for the macro IB_UMEM_MAX_PAGE_CHUNK
to stay in ib_verbs.h. Move the macro to umem.c, the only place where
it is used.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The address handle associated with dual-sided RMPP direction switch
ACKs is never destroyed. Free the AH for ACKs which fall into this
category.
Problem was reported by Dotan Barak <dotanb@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Nothing looks at the return value of agent_send_response(), so there's
no point in returning anything.
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If agent_send_response() returns an error, we shouldn't do anything
differently than if it succeeds; setting response to NULL just means
that the response buffer gets leaked.
Signed-off-by: Suresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If ib_mad_recv_done_handler() fails to allocate response, then it just
printed a warning and continued, which leads to an oops if the MAD is
being handled for a switch device, because the switch code uses
response without checking for NULL. Fix this by bailing out of the
function if the allocation fails.
Signed-off-by: Suresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that ib_find_pkey() ignores the membership bit of P_Keys, there's no
need for ib_sa to look for both 0x7fff and 0xffff in a port's P_Key table.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_find_pkey() is used as a replacement for ib_find_cached_pkey(), and
the original function ignored the membership bit when searching for a
P_Key, so ib_find_pkey() should ignore the bit too.
In particular, IPoIB turns on the P_Key membership bit of limited
membership P_Keys when creating a child interface and looks for the
full membership P_key. This broke if a port was a partial member of a
partition when IPoIB switched from ib_find_cached_pkey() to
ib_find_pkey(), and this change fixes things again.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
One patch for two trivial typos of 'error' with three R's, appearing in message strings.
There's a bunch more of the same in comments, not dealt with here.
Signed-off-by: Eddy L O Jansson <eddy@klopper.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: Workaround problem of errormask register being overwritten
IB/ipath: Fix some issues with buffer cancel and sendctrl register update
IB/ipath: Use faster put_tid_2 routine after initialization
IB/ipath: Remove unsafe fastrcvint code from interrupt handler
IB/ehca: Move extern declarations from .c files to .h files
IB/mlx4: Whitespace fix
IB/ehca: Fix include order to better match kernel style
mlx4_core: Remove kfree() in mlx4_mr_alloc() error flow
RDMA/amso1100: Initialize the wait_queue_head_t in the c2_qp structure
On some system hardware, we are seeing moderately common cases of the
chip errormask register being overwritten due to a chip bug in iba6120
that is triggered by a vendor-specific PCIe broadcast message. This
patch merely checks periodically, and corrects it if needed (the
overwrite can cause us to not get error and hardware error
interrupts). Also, make dd->ipath_errormask the one, true canonical
source for kr_errormask, and remove references to ipath_ignorederrs as
it is currently unused.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There was confused use of INFINIPATH_S_PIOBUFAVAILUPD (value) and
IPATH_S_PIOBUFAVAILUPD (bit position). Also, some callers of
ipath_cancel_sends() need kr_sendctrl restored, and some want to do it
later.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one time the ipath_minrev field was initialized prior to the
ipath_init_iba6120_funcs call, but that is no longer the case, so the
slower put_tid routine was always being used.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The fastrcvint code's purpose was to avoid reading the interrupt
status if kernel packets were in the receive queue (to reduce
overhead). Because intstatus was not read, we could miss the error
interrupt bit indicating freeze mode, since it only delivers a single
interrupt, even if still pending after intclear is written.
This patch removes that unsafe optimization.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
Make sure declarations stay in sync with definitions by keeping all
extern declarations in common .h files.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
