First control messages to the stick timeouts very often due to probable
hw bug. Repeat first message few times if it fails as workaround.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bug causes 2nd FE MPEG TS buffer size to be zero and therefore no picture
when 2nd FE was enabled. Configure correct buffer size also for 2nd FE.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default case of the switch didn't unlock the mutex.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Revert a change made in change 9743 which resulted in a kernel panic in some
cases on shutdown of the audio stream.
First discovered when working on the Pinnacle 880e support, and later
reproduced by a user on the mailing list with the HVR-900 as well.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for KWorld 330U Board
Many thanks to Devin and Mauro!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for KWorld 330U AC97
Many thanks to Devin and Mauro again!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the conversion to v4l2_subdev one bit of code was accidentally dropped:
on receiving the first command the driver has to load the fw. A new init()
command was introduced to do that explicitly for bridge drivers that are
converted to use v4l2_subdev, but old drivers that are not yet converted
no longer worked.
This patch fixes this regression for these old drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_QUERYCTRL command needs to actually do a queryctrl, not a
querymenu. Similarly, the VIDIOC_QUERYMENU command needs to actually
do a querymenu not a queryctrl.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch adds support for a new version of the
Terratec Cinergy DT USB XS Diversity Dual DVB-T TV tuner stick.
The USB ID of the new stick is 0ccd:0081.
The hardware of the stick has changed, when compared to the first version of
this stick, but it still uses quite standard components, so that only minor
changes are needed to the sources.
The patch has been successfully tested with hotplugging the device and then
2 x tzap and 2 x mplayer, to watch two different TV programs simultaneously.
The stick works with both, the old and new firmwares:
- dvb-usb-dib0700-1.10.fw and
- dvb-usb-dib0700-1.20.fw
Signed-off-by: Nicolas Fournier <nicolasfournier@yahoo.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some em28xx devices use the PCM IN AC 97 PIN for digital audio. However,
currently, the PCM IN selection is not set by the driver. This patch allows
specifying the PCM IN expected output, via board description table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zoran driver does a module_get/put of THIS_MODULE on device open/close.
This isn't necessary as the kernel does this automatically.
Clean up the failure path of zoran_open() somewhat.
Make the dprintk()s on open/close a higher debug level and make the user
count printed take the current open/close into account.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver should only use the kernel mapped io address, zr36057_mem, and
not the PCI bus address, zr36057_adr. Since the latter is only printed out
once, there is no need to save it in the driver data structure.
There was some old code that looked like it was for the Alpha architecture
which would use the PCI bus address. It probably no longer applies to
modern kernels.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using custom code, just let the device layer look it up for us
from the pci device table. This requires extending the pci device table to
list each known card, plus a catch-all entry for the cards that don't have
sub-system vendor/device data.
Improve some of the info and error messages too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver was keeping a global array with an entry for each zoran device
probed. It was a leftover from when the driver didn't dynamically allocate
the driver data for each device.
There was only one use left, in the video device's ->open() method, looking
up the struct zoran for the opened device from the minor number. This can
be done better with video_get_drvdata().
Since zoran_num is now only used in the pci driver's ->probe() method, it
doesn't need to be an atomic_t and be static. There is a race if multiple
zoran cards could be probed at the same time, but currently the probe
method for a given driver is single threaded.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When initializing a module parameter that is a per-card array, use
"{ [0 ... (BUZ_MAX-1)] = -1 }" instead of "{ -1, -1, -1, -1 }". This way
all of the entries will be correctly set to -1 if someone changes BUZ_MAX
to a value other than 4.
Adjust some of the parameter help text too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When enabling a shared IRQ line, then saa7134_irq handler could be invoked
before the driver had completely set up internal structures, due to a shared
interrupt line firing. Clear the saa7134 interrupt status reg, before
requesting the irq line, so that stale IRQ status isn't processed before the
internal structures are set up.
Marcin Slusarz recently brought this Oops to the attention of the v4l-dvb
lists and provided an initial analysis by investigating reports found here:
http://kerneloops.org/guilty.php?guilty=mute_input_7133&version=2.6.27-release&start=1802240&end=1835007&class=oops
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Analog support for HVR-1250 has not been completed, but does exist for
the HVR-1800.
Since both cards use the same driver, it tries to create the analog
dev for both devices, which is not possible.
This causes a NULL error to show up in video_open and mpeg_open.
-Mark
Iterations through the cx23885_devlist must check for NULL
pointers as some supported devices only have DVB support at the moment.
Mark Jenks encoutered an Oops in a system with both an HVR-1250 and HVR-1800
installed.
-Andy
Reported-by: Mark Jenks <mjenks1968@gmail.com>
Tested-by: Mark Jenks <mjenks1968@gmail.com>
Signed-off-by: Mark Jenks <mjenks1968@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register 0x2d has to be set differently in the saa7129 compared to the
saa7127. This was not done correctly, so S-Video was broken in certain
circumstances.
This fixes a regression introduced in 2.6.28.
Signed-off-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a really old and crufty driver that wasn't using the long
established pci driver framework.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
[mchehab@redhat.com: Cleaned up a few CodingStyle issues]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If Hauppauge eeprom is corrupted, the driver returns tuner = 0, instead
of TUNER_ABSENT.
This makes the drivers to initialize tuner, instead of handling the
manual parameter.
Since the tuner core rejects that a tuner to have their type changed,
this breaks the manual tuner override.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 60b4bde48b removed an unused
struct on zoran driver, when compiled with "Y".
However, as pointed by Jean Delvare <khali@linux-fr.org>, this is
neeeded when the driver is compiled as a module, since udev relies on it
to auto-load the module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Concurrent access to a single DVB CA 50221 interface slot is generally
discouraged. The underlying drivers (budget-av, budget-ci) do not implement
proper locking and thus two transactions could (and do) interfere with on
another.
This fixes the following problems seen by others and myself:
- sudden i/o errors when writing to the ci device which usually would
result in an undefined state of the hw and require a software restart
- errors about the CAM trying to send a buffer larger than the agreed size
usually also resulting in an undefined state of the hw
Due the to design of the DVB CA 50221 driver, implementing the locks in the
underlying drivers would not be enough and still leave some race conditions,
even though they were harder to trigger.
Signed-off-by: Matthias Dahl <devel@mortal-soul.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
to avoid:
| tvp514x 0-005c: No platform data
| !!<3>tvp514x 0-005d: No platform data
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap <randy.dunlap@oracle.com> wrote:
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c: In function 'cx88_call_i2c_clients':
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:122: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:123: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:127: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:128: error: 'struct cx88_core' has no member named 'gate_ctrl'
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC specification release number is a binary-coded decimal number, print
it as such.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces support for dvb-t for the following dibcom based card:
Terratec Cinergy T Express (USB-ID: 0ccd:0062)
Signed-off-by: Yusuf Altin <yusuf.altin@t-online.de>
Signed-off-by: Albert Comerma <albert.comerma@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx were trying to access the third input entry, even for boards that
don't support it.
This patch reviews the input mux selection fixing this bug and a few
other troubles, like not validating the input on one userspace ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cameras should generate KEY_CAMERA, not BTN_0. Also call input_sync()
on the device once the button has been pressed.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use internal network_device_stats that exist in network device and
net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Randy Dunlap <randy.dunlap@oracle.com> reported, cx88 has some compilation issues:
drivers/built-in.o: In function `cx88_call_i2c_clients':
(.text+0x20af17): undefined reference to `videobuf_dvb_get_frontend'
drivers/built-in.o: In function `cx8802_probe':
cx88-mpeg.c:(.devinit.text+0x268c4): undefined reference to `videobuf_dvb_alloc_frontend'
cx88-mpeg.c:(.devinit.text+0x268ea): undefined reference to `videobuf_dvb_dealloc_frontends'
With those configs:
CONFIG_VIDEO_CX88=y
CONFIG_VIDEO_CX88_BLACKBIRD=y
CONFIG_VIDEO_CX88_DVB=m
CONFIG_DVB_CORE=m
After carefully examining the code, with the current code, several cx88 drivers
(cx8800, cx8802, cx88_dvb and cx88_blackbird) should be compiled as a module,
if one of them is marked as such. Just fixing Kconfig could create a very complex
set of rules. Also, this hides a problem with the current approach where the dvb
functionality weren't confined inside dvb module.
What happens is that:
- cx88-i2c (part of cx8800) has some special rules if DVB;
- cx88-mpeg (cx8802 module) has also part of DVB init code;
- cx88-dvb has the rest of the dvb code;
- cx88-blackbird can be used with cx88-mpeg, having cx88-dvb or not.
So, instead of doing some tricks at Kconfig and wait for a next breakage,
this patch moves the dvb code inside cx88-i2c and cx88-mpeg into cx88-dvb.
Another problem is that cx8802 were being compiled, even without cx88-dvb
and cx88-blackbird modules.
While on this code, let's fix also a reported problem:
http://www.linuxtv.org/pipermail/linux-dvb/2009-January/031225.html
A solution for the issue were proposed here:
http://www.mail-archive.com/linux-media@vger.kernel.org/msg00021.html
Thanks to Randy, Andy, Gregoire and Thomas for helping us to detect
and solve the issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Randy Dunlap <randy.dunlap@oracle.com>:
With CONFIG_INPUT=m and CONFIG_DVB_DM1105=y:
drivers/built-in.o: In function `input_sync':
dm1105.c:(.text+0x120c33): undefined reference to `input_event'
drivers/built-in.o: In function `dm1105_emit_key':
dm1105.c:(.text+0x120c6c): undefined reference to `input_event'
dm1105.c:(.text+0x120c82): undefined reference to `input_event'
dm1105.c:(.text+0x120cb2): undefined reference to `input_event'
dm1105.c:(.text+0x120cd1): undefined reference to `input_event'
drivers/built-in.o: In function `dm1105_ir_init':
(.devinit.text+0xd8ae): undefined reference to `input_allocate_device'
drivers/built-in.o: In function `dm1105_ir_init':
(.devinit.text+0xd9f6): undefined reference to `input_register_device'
drivers/built-in.o: In function `dm1105_ir_init':
(.devinit.text+0xda09): undefined reference to `input_free_device'
drivers/built-in.o: In function `dm1105_ir_exit':
(.devexit.text+0xcde): undefined reference to `input_unregister_device'
This is due to the lack of a dependency between dm1105 and CONFIG_INPUT
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't call tda8290_init_tuner unless we have either a TDA8275 or TDA8275A
present. Calling this function will cause a TDA18271 to get sick, so we
should only call it when needed.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
anysee.c:44:5: warning: symbol 'dvb_usb_anysee_delsys' was not declared. Should it be static?
cx24116.c:378:3: warning: symbol 'CX24116_MODFEC_MODES' was not declared. Should it be static?
stb0899_algo.c:57:5: warning: symbol 'stb0899_get_srate' was not declared. Should it be static?
stb0899_algo.c:766:6: warning: symbol 'Log2Int' was not declared. Should it be static?
stb0899_drv.c:137:20: warning: symbol 'stb0899_quant_tab' was not declared. Should it be static?
stb0899_drv.c:180:20: warning: symbol 'stb0899_est_tab' was not declared. Should it be static?
stb0899_drv.c:220:5: warning: symbol '_stb0899_read_reg' was not declared. Should it be static?
budget-ci.c:1348:23: warning: symbol 'tt3200_stb6100_config' was not declared. Should it be static?
/home/v4l/master/v4l/cx25840-core.c:190:6: warning: symbol 'cx25840_work_handler' was not declared. Should it be static?
/home/v4l/master/v4l/m5602_s5k83a.c:116:6: warning: symbol 's5k83a_dump_registers' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/tda8290.c:233:7: warning: symbol 'i' shadows an earlier one
/home/v4l/master/v4l/tda8290.c:178:3: warning: symbol 'fm_mode' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/dvb_frontend.c:838:19: warning: symbol 'dtv_cmds' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1035:6: warning: symbol 'dtv_property_dump' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1066:5: warning: symbol 'is_legacy_delivery_system' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1080:6: warning: symbol 'dtv_property_cache_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1132:6: warning: symbol 'dtv_property_legacy_params_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1187:6: warning: symbol 'dtv_property_adv_params_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1222:6: warning: symbol 'dtv_property_cache_submit' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1253:5: warning: symbol 'dtv_property_process_get' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1362:5: warning: symbol 'dtv_property_process_set' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/em28xx-core.c:396:25: warning: symbol 'outputs' was not declared. Should it be static?
/home/v4l/master/v4l/em28xx-input.c:324:6: warning: symbol 'em28xx_ir_start' was not declared. Should it be static?
/home/v4l/master/v4l/em28xx-cards.c:1925:5: warning: symbol 'em28xx_init_dev' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. now pxa_camera.c uses ioremap() for register access, pxa_camera.h is
totally useless. Remove it.
2. <asm/dma.h> does no longer include <mach/dma.h>, include the latter
file explicitly
delete mode 100644 drivers/media/video/pxa_camera.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not all architectures provide clear_user_page(), but clear_user_highpage()
is available everywhere at least via the compatibility inline function.
Is this the "trivial patch" that's required for these two drivers?
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a number of drivers which set their i2c bus class to
I2C_CLASS_CAM_DIGITAL, however no chip driver actually checks for this
flag, so we might as well drop it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
f_op->poll is the only vfs operation which is not allowed to sleep. It's
because poll and select implementation used task state to synchronize
against wake ups, which doesn't have to be the case anymore as wait/wake
interface can now use custom wake up functions. The non-sleep restriction
can be a bit tricky because ->poll is not called from an atomic context
and the result of accidentally sleeping in ->poll only shows up as
temporary busy looping when the timing is right or rather wrong.
This patch converts poll/select to use custom wake up function and use
separate triggered variable to synchronize against wake up events. The
only added overhead is an extra function call during wake up and
negligible.
This patch removes the one non-sleep exception from vfs locking rules and
is beneficial to userland filesystem implementations like FUSE, 9p or
peculiar fs like spufs as it's very difficult for those to implement
non-sleeping poll method.
While at it, make the following cosmetic changes to make poll.h and
select.c checkpatch friendly.
* s/type * symbol/type *symbol/ : three places in poll.h
* remove blank line before EXPORT_SYMBOL() : two places in select.c
Oleg: spotted missing barrier in poll_schedule_timeout()
Davide: spotted missing write barrier in pollwake()
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Brad Boyer <flar@allandria.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several subsystem open handlers dereference the fops_get() return value
without checking it for nullness. This opens a race condition between the
open handler and module unloading.
A module can be marked as being unloaded (MODULE_STATE_GOING) before its
exit function is called and gets the chance to unregister the driver.
During that window open handlers can still be called, and fops_get() will
fail in try_module_get() and return a NULL pointer.
This change checks the fops_get() return value and returns -ENODEV if NULL.
Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The radio_release function of the BTTV driver is missing a call to
v4l2_prio_close. As a result, after the radio device has been opened at
least once (e.g., by HAL during bootup), v4l2_priority will never drop below
V4L2_PRIORITY_INTERACTIVE again. With the following patch against 2.6.28,
applications that run with V4L2_PRIORITY_BACKGROUND are able to open devices
again. Previous Linux versions are affected as well.
Signed-off-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code had calls to both usb_set_intfdata and dev_set_drvdata, doing the
same thing.
The semantic patch that lead to finding this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@header@
@@
@same depends on header@
position p;
@@
usb_set_intfdata@p(...) { ... }
@depends on header@
position _p!=same.p;
identifier _f;
struct usb_interface *intf;
expression data;
@@
_f@_p(...) { <+...
- dev_set_drvdata(&intf->dev, data);
+ usb_set_intfdata(intf, data);
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The GPIO logic for LNA control on the Tiger r2 devices was inverted.
This patch corrects the problem.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Report to userspace that cx24116 and stv0899 drivers support DVB-S2.
Signed-off by: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices require different setups on struct_audio. Due to that, we
may need to change some fields at dev.adev during device probe. So, this
patch moves the dynamic memory allocation of adev at em28xx-alsa to the
dynamic allocation of struct em28xx dev that happens during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes autodetection for Avermedia AVerTV GO 007 FM Plus (M15C)
(PCI ID 1461:f31d).
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Avermedia AVer TV GO 007 FM Plus (M15C) on
saa7134 driver (PCI ID 1461:f31d).
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for radio driver TEA5764 from NXP.
This chip is connected in pxa I2C bus in EZX phones
from Motorola, the chip is used in phone model A1200.
This driver is for OpenEZX project (www.openezx.org)
Tested with A1200 phone, openezx kernel and fm-tools
[mchehab@redhat.com: Fixed CodingStyle and solved some merge conflicts]
Signed-off-by: Fabio Belavenuto <belavenuto@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix I2C bridge error in zl10353 if no tunner attached to internal I2C
bus of zl10353 chip.
When set enable bridge from internal I2C bus to the main I2C bus
(saa7134) the main I2C bus stopped very hardly. No any communication. In
our next board we solder additional resistors to internal I2C bus.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since ttusb_dec.c relies on pci_alloc_consistent and
pci_free_consistent, make it depend on PCI in Kconfig.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since dvb-ttusb-budget.c relies on pci_alloc_consistent and
pci_free_consistent, make it depend on PCI in Kconfig.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the i2c driver ID will be removed in the near future we have to
modify the v4l2 debugging API to use the driver name instead of driver ID.
Note that this API is not used in applications other than v4l2-dbg.cpp
as it is for debugging and testing only.
Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged
with a warning that it is deprecated and will be removed in 2.6.30.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This rename prevents conflicts with the older compat_ioctl32 module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since internal to v4l2 the ioctl prototype is the same regardless of it
being called through .ioctl or .unlocked_ioctl, we need to convert it all
to the long return type of unlocked_ioctl.
Thanks to Jean-Francois Moine for posting an initial patch for this and
thus bringing it to our attention.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (583 commits)
V4L/DVB (10130): use USB API functions rather than constants
V4L/DVB (10129): dvb: remove deprecated use of RW_LOCK_UNLOCKED in frontends
V4L/DVB (10128): modify V4L documentation to be a valid XHTML
V4L/DVB (10127): stv06xx: Avoid having y unitialized
V4L/DVB (10125): em28xx: Don't do AC97 vendor detection for i2s audio devices
V4L/DVB (10124): em28xx: expand output formats available
V4L/DVB (10123): em28xx: fix reversed definitions of I2S audio modes
V4L/DVB (10122): em28xx: don't load em28xx-alsa for em2870 based devices
V4L/DVB (10121): em28xx: remove worthless Pinnacle PCTV HD Mini 80e device profile
V4L/DVB (10120): em28xx: remove redundant Pinnacle Dazzle DVC 100 profile
V4L/DVB (10119): em28xx: fix corrupted XCLK value
V4L/DVB (10118): zoran: fix warning for a variable not used
V4L/DVB (10116): af9013: Fix gcc false warnings
V4L/DVB (10111a): usbvideo.h: remove an useless blank line
V4L/DVB (10111): quickcam_messenger.c: fix a warning
V4L/DVB (10110): v4l2-ioctl: Fix warnings when using .unlocked_ioctl = __video_ioctl2
V4L/DVB (10109): anysee: Fix usage of an unitialized function
V4L/DVB (10104): uvcvideo: Add support for video output devices
V4L/DVB (10102): uvcvideo: Ignore interrupt endpoint for built-in iSight webcams.
V4L/DVB (10101): uvcvideo: Fix bulk URB processing when the header is erroneous
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_is_isoc_in(epd)
usb_endpoint_is_isoc_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: clean up
RW_LOCK_UNLOCKED is deprecated. This patch replaces it with the
__RW_LOCK_UNLOCKED(lock) macro. This change was a little trickier than
others due to the macro being used in another macro that fills an array.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed by gcc:
drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c: In function ‘hdcs_set_size’:
drivers/media/video/gspca/stv06xx/stv06xx_hdcs.c:301: warning: ‘y’ may be used uninitialized in this function
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was trying to query the AC97 registers for the vendor
information even if it was clearly not a AC97 audio device (resulting in errors
in the dmesg output). This was due to a bug in the way we did the check.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add additional output formats, which will be useful for the Pinnacle PCTV
Ultimate 880e integration with the saa7136.
Thanks to Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Noticed when doing the audio support for the Pinnacle PCTV HD Ultimate 808e
that the modes were incorrect (the 808e uses I2S in 5 sample mode)
Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Like the em2874, the em2870 does not have any analog support, so don't bother
loading the em28xx-alsa module.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Pinnacle 80e cannot be supported since Micronas yanked their driver
support for the drx-j chipset at the last minute. Remove the device profile
since it cannot work without the drx driver and it being there is only likely
to confuse people into thinking the device is supported but not working.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DVC 100 profile is redundant since we already have an existing identical
profile named "Pinnacle Dazzle DVC 90/DVC 100"
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct problem introduced during the board refactoring where the XCLK
frequency would get zero'd out. The sequence of events was as follows:
em28xx_pre_card_setup() called em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration
em28xx_pre_card_setup() would set the dev->board.xclk if not set
em28xx_pre_card_setup() would set the XCLK register based on dev->board.xclk
...
em28xx_card_setup() would call em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration (clearing out
value of dev->board.xclk set in em28xx_pre_card_setup)
...
em28xx_audio_analog_set() sets the XCLK register based on dev->board.xclk
(which now contains zero)
The change sets the default XCLK and I2C Clock fields in the board definition
inside of em28xx_set_model() so that subsequent calls do not cause the
values to be overwritten.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix this warning:
drivers/media/video/zoran/zoran_card.c:156: warning: ‘zr36067_pci_tbl’ defined but not used
Currently, zoran driver relies on a find routine that doesn't use the
pci table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_set_coeff’:
drivers/media/dvb/frontends/af9013.c:231: warning: ‘ns_coeff2_8k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:230: warning: ‘ns_coeff2_2k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:229: warning: ‘ns_coeff1_8193nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:228: warning: ‘ns_coeff1_8192nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:227: warning: ‘ns_coeff1_8191nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:226: warning: ‘ns_coeff1_2048nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_snr’:
drivers/media/dvb/frontends/af9013.c:1012: warning: ‘snr_table’ may be used uninitialized in this function
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed to sync with the development tree. Probably, a merge
conflict were solved by adding this blank line.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/usbvideo/quickcam_messenger.c: In function ‘qcm_sensor_init’:
drivers/media/video/usbvideo/quickcam_messenger.c:450: warning: operation on ‘ret’ may be undefined
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes this warning:
drivers/media/video/gspca/gspca.c:1811: warning: initialization from incompatible pointer type
The reason is that the returned argument should be a long, not an
integer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/anysee.c: In function ‘anysee_master_xfer’:
drivers/media/dvb/dvb-usb/anysee.c:156: warning: ‘ret’ may be used uninitialized
By looking at the function, altrough very unlikely, this might
eventually be true if num = 0. So, better to fix the warning by
initializing with ret = 0.
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend the range of supported UVC devices by allowing video output devices
matching the following structure:
TT_STREAMING -> VC_PROCESSING_UNIT -> VC_EXTENSION_UNIT{0,n} -> OTT_*
Video output devices are reported with the V4L2_CAP_VIDEO_OUTPUT capability
flag and are subject to the same restrictions as video input devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Built-in iSight webcams have an interrupt endpoint but spit proprietary data
that don't conform to the UVC status endpoint messages. Don't try to handle
the interrupt endpoint for those cameras.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the first bulk URB of a video payload contains an erroneous header, or
when no V4L2 buffer is available, the whole payload must be dropped. Change
the skip logic to drop all bulk URBs until the end of the payload instead of
the first one only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This camera is rather similar to MT9M001, but also has a couple of
enhanced features, like pixel binning.
create mode 100644 drivers/media/video/mt9t031.c
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't modify driver's state in try_fmt, just verify format acceptability
or adjust it to driver's capabilities.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
priv->scale is checked in start_capture.
Therefore, it should be NULL if failing in set_fmt.
This patch resolve this problem.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds tw9910 driver that use soc_camera framework.
It was tested on SH Migo-r board and mplayer.
create mode 100644 drivers/media/video/tw9910.c
create mode 100644 include/media/tw9910.h
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sh_mobile_ceu_camera.c is already prepared to support interlaced format, this
patch moves the choice of a field type down to host and / or camera drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch cleans up the sh_mobile_ceu driver and adds comments and
constants to clarify the magic sequence in sh_mobile_ceu_capture().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch presents new method to be able to select V4L2 input type
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch presents new method to be able to check v4l2_std_id
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds NV16/NV61 support to the sh_mobile_ceu driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds NV12/NV21 support to the sh_mobile_ceu driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move mutex from host drivers to camera device object, take into account
videobuf locking.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the introduction of the format conversion support in soc-camera, we now
also have to take care to pass the correct pixel format to the camera driver
when calling its try_fmt() method.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplify multiple drivers by replacing f->fmt.pix.* with a single pointer
dereference, merge some needlessly broken lines, verify host and camera
operations pointers on registration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the sh_mobile_ceu driver to make use
of the new pixel format translation code. Only pass-though
mode at this point.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using PXA270's FIFO inactivity time-out register (CITOR) reduces FIFO overruns.
The time-out is calculated in CICLK / LCDCLK ticks and has to be longer than
one pixel time. For this we have to know the pixel clock frequency, which
usually is provided by the camera. We use the struct soc_camera_sense to
request PCLK frequency from the camera driver upon each data format change.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Antonio Ospite <ospite@studenti.unina.it> two platforms with a
mt9m111 camera require opposite pixel clock polarity, which means one of them
inverts it. This patch adds support for inversion flags and switches all
available camera drivers to using them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"static" on stv06xx for all static functions and parameters to avoid
such troubles.
Cc: Erik Andren <erik.andren@gmail.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Testing for non-NULL platform-data is not enough, we have to check if the GPIO
in the platform data is valid or not. Also see my earlier patch:
[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Micron mt9m111 offers 4 byte orders for YCbCr
output. This patchs adds all possible outputs capabilities
to the mt9m111 driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch replace return -1; with return retval; in 3 functions.
And we also change if-checks for this returned values.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a lot of patches for dsbr100 last time we should update version
of driver.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We should use dev_err (not dev_warn) if video_register_device fails.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We should make if-constructions more clear. Introduce int retval
variables in some functions to make it this way. Also a lot of useful
dev_err messages added. And now we check every returned value after
usb_control_msg.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove printk in one line and place dev_warn there.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch corrects unplug procedure. Patch adds
usb_dsbr100_video_device_release, new macros - videodev_to_radio, mutex
lock and a lot of safety checks.
Struct video_device videodev is embedded in dsbr100_device structure.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Because this device doesn't provide any powermanagment capabilities(may
be they exist but unknown to me yet, so they are not implemented), we
should turn them off. Patch sets support_autosuspend equal to 0.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch corrects unplug procedure, that was implemented wrong in
previous patch. New function usb_amradio_device_release added.
Disconnect lock removed.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The po1030 never sends long i2c messages, no need to test for that in
the init phase.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the s5k83a sensor to use the common read_sensor function
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the s5k4aa sensor to use the common read_sensor function
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Toggle read sensor sequence depending on type of sensor. Check that no
more than max width of a sensor is read.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
First step into unifying the read and write sensor functions
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This restores the correct boolean expression
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The buffer type is already checked in v4l2-ioctl.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- move the rev12a sequence from setcontrast to end of start
- add the white balance control for rev72a
- adjust the contrast formula
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the initialization of the URB list for a DVB-USB device to prevent
problems on certain platforms (MIPS).
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, just two routines are enough for analog: the first one configs the analog
part and register V4L2 devices, and the second one release analog devices.
After this patch, it will be easier to transform em28xx-video into an em28xx
extension, loaded only on analog devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx-video were holding several code that are not specific to V4L2
interface.
This patch moves the core code for em28xx-core, and usb probing code
into em28xx-cards.
This opens the possibility of breaking em28xx into a core module and a
V4L2 module, loaded only on devices that have analog interfaces.
Some cleanup may be done at em28xx-cards to optimize the config code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements VIDIOC_ENUM_FRAMESIZES, it is used at least
by gstreamer.
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib7000p.h defines a few extern symbols when CONFIG_DVB_DIB7000P is not set. since the
header is used on more than one driver, this causes symbol duplication, as pointed by
Ingo Molnar <mingo@elte.hu>:
drivers/media/dvb/built-in.o: In function `dib7000p_set_gpio':
(.text+0x3f242): multiple definition of `dib7000p_set_gpio'
drivers/media/video/built-in.o:(.text+0xb8c1e): first defined here
drivers/media/dvb/built-in.o: In function `dib7000p_i2c_enumeration':
(.text+0x3f282): multiple definition of `dib7000p_i2c_enumeration'
drivers/media/video/built-in.o:(.text+0xb8c3e): first defined here
drivers/media/dvb/built-in.o: In function `dib7000p_set_wbd_ref':
(.text+0x3f1c1): multiple definition of `dib7000p_set_wbd_ref'
drivers/media/video/built-in.o:(.text+0xb8bfe): first defined here
LD drivers/net/built-in.o
make[2]: *** [drivers/media/built-in.o] Error 1
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that use v4l2_device can set that as parent pointer in the v4l2_dev
field instead of using the struct device parent field.
This allows v4l2-dev.c to check whether this driver is v4l2_device based,
and if so then it can offer additional services.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of relying on the cdev release callback we should rely on the
release callback from the device struct. This requires that we use
get_device/put_device to do proper refcounting. In order to do this
safely v4l2-dev.c now sets up its own file_operations that call
out to the driver's ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usbvideo_ClientIncModCount may return value < 0 in the case of error, not > 0.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted to v4l2_subdev. While doing that I also discovered a stray 'break'
that broke the S_CTRL handling. Fixed that as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver can be coupled to an anciliary AC97 chip. This patch
allows read/write AC97 registers directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_index requires a valid parent device in order to discover which
indices are in use. Some drivers (e.g. pvrusb2) do not set the parent
device. In that case just return 0.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bt832 i2c driver was never used or even compiled and is no longer
maintained. It is now removed completely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a consistent crystal value of 28.636360 MHz for computing all PLL
parameters so clocks don't have relative error due to assumed crystal
value mismatches. Also aimed to have all PLLs run their VOCs at close to
400 MHz to minimze the error of these PLLs as frequency synthesizers. Also
set the VDCLK and AIMCLK PLLs to sane values before the APU and CPU firmware
are loaded. Also fixed I2S Master clock dividers.
Many thanks to Mike Bradley and Jeff Campbell for reporting this problem and
suggesting the solution, researching and experimenting, and performing
extensive testing to support their suggested solution.
Reported-by: Jeff Campbell <jac1dlists@gmail.com>
Reported-by: Mike Bradley <mike.bradley@incanetworks.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disable AV_LOCK, locking of audio PLL to video PLL in the cx18-av-core for
analog captures. It seems to have adverse effects on captures from
SVideo and CVBS sources with current clock & crystal settings in the driver.
Many thanks to Jeff Campbell and Mike Bradley for reporting this problem,
and suggesting the solution and performing extensive testing to support their
suggestion.
Reported-by: Jeff Campbell <jac1dlists@gmail.com>
Reported-by: Mike Bradley <mike.bradley@incanetworks.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added all missing v4l1/2 ioctls and fix several broken conversions.
Partially based on work done by Cody Pisto <cpisto@gmail.com>.
Tested-by: Brandon Jenkins <bcjenkins@tvwhere.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the gp8psk module to use the S2API.
It pretends to be DVB-S2 capable in order to allow the various
supported modulations (8PSK, QPSK-Turbo, etc), and keep software
compatibility with the S2API patches for Mythtv and VDR.
Signed-off by: Alan Nisota <alannisota@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch uses the same code for enumberating video formats that are
present on cx88, bttv and saa7134 drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The changeset 78aa52a159cf introduced a bug on em28xx: buffer setup should be
awaking xc3028. Instead, since we didn't specify the tuner mode, the device
were going to sleep, due to the lack of tuner mode when asking tuner to handle
VIDIOC_S_FREQUENCY:
xc2028 0-0061: Device is Xceive 3028 version 1.0, firmware version 2.7
xc2028 0-0061: divisor= 00 00 14 d0 (freq=83.250)
xc2028 0-0061: Putting xc2028/3028 into poweroff mode.
xc2028 0-0061: Printing sleep stack trace:
Pid: 10936, comm: mplayer Tainted: P M 2.6.27.8 #1
Call Trace:
[<ffffffffa0b759ea>] xc2028_sleep+0x89/0x1ab [tuner_xc2028]
[<ffffffffa0b48fb9>] tuner_s_frequency+0xf5/0x165 [tuner]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init_fw option was broken for the HVR-950q because we would call the reset
callback inside of dvb_attach() and the callback had not been setup yet.
Michael Krufky (who added the init_fw feature) says it's no longer required,
so just remove the option completely.
Thanks to user Zzeiss from #linuxtv chat for reporting the issue and
Michael Krufky <mkrufky@linuxtv.org> for proposing the fix.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't operate under the assumption that every device that uses the em2820
default USB ID is a Prolink PlayTV USB. We have an eeprom hash, so use that,
since otherwise we cannot support other devices with the 2820 default USB ID
(such as the ADS Tech Instant TV USB USBAV-704)
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the em2870 to the list of known em28xx chip ids.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
