No functional change, just use the same names as i386.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Skip clock calibration if cpu being brought online is exactly the same
speed, stepping, etc., as the previous cpu. This significantly reduces
the time to boot very large systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64 expects following vm layout:
== low memory
[register-stack grows up]
[memory-stack grows down]
== high memory
But the code assigns the base of the register stack at the
maximum stack size offset from the fixed address where the
stack *might* start. Stack randomization will result in the
memory stack starting at a lower address than this, and if the
user has set a low stack limit with "ulimit -s", then you can
end up with the register stack above the memory stack (or if
you were very unlucky right on top of it!).
Fix: Calculate the base address for the register stack starting
from the actual address of the memory stack.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following 'if' statement in ia64_setup_msi_irq() always fails even
if create_irq() returns <0 value, because variable 'irq' is defined as
unsigned int. It would cause invalid memory access.
irq = create_irq();
if (irq < 0)
return irq;
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
So I think the right solution is to simply make pci_enable_device just
flip enable bits and move the rest of the work someplace else.
However a thorough cleanup is a little extreme for this point in the
release cycle, so I think a quick hack that makes the code not stomp the
irq when msi irq's are enabled should be the first fix. Then we can
later make the code not change the irqs at all.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: IA64: fix %ll build warnings
ACPI: IA64: fix allnoconfig build
ACPI: Only use IPI on known broken machines (AMD, Dothan/BaniasPentium M)
ACPI: ibm-acpi: allow module to load when acpi notifiers can't be set (v2)
ACPI: parse 2nd MADT by default
ACPICA: revert "acpi_serialize" changes
sony-laptop: MAINTAINERS fix entry, add L: and W:
ACPI: resolve HP nx6125 S3 immediate wakeup regression
ACPI: Add support to parse 2nd MADT
In sn_io_slot_fixup(), the parent is re-set from the bus to
io(port|mem)_resource because the address is changed in a way that it's not
child of the bus any more.
However, only the root is set but not the parent/child/sibling relationship in
the resource tree which causes 'cat /proc/iomem' to stop after this memory
area. Depding on the poition in the tree the iomem may be nearly completely
empty.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When booting an SN system without specifing a console
(i.e., no "console=" on boot line), the system will hang during
boot at the point where /sbin/init is run.
The problem is that vga_console_iobase is not converted to a
virtual address before storing in io_space[0].mmio_base.
The conversion was happening in sn_scan_pcdp(), but not in
setup_vga_console().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Clearly should be checking for "val == DIE_INIT_SLAVE_ENTER".
Signed-off-by: Jay Lan <jlan@sgi.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If a system consists of mixed processor types, kmalloc()
can be called before the per-cpu data page is initialized.
If the slab contains sufficient memory, then kmalloc() works
ok. However, if the slabs are empty, slab calls the memory
allocator. This requires per-cpu data (NODE_DATA()) & the
cpu dies.
Also noted by Russ Anderson who had a very similar patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We have seen bad_pte_print when testing crashdump on an SN machine in
recent 2.6.20 kernel. There are tons of bad pte print (pfn < max_low_pfn)
reports when the crash kernel boots up, all those reported bad pages
are inside initmem range; That is because if the crash kernel code and
data happens to be at the beginning of the 1st node. build_node_maps in
discontig.c will bypass reserved regions with filter_rsvd_memory. Since
min_low_pfn is calculated in build_node_map, so in this case, min_low_pfn
will be greater than kernel code and data.
Because pages inside initmem are freed and reused later, we saw
pfn_valid check fail on those pages.
I think this theoretically happen on a normal kernel. When I check
min_low_pfn and max_low_pfn calculation in contig.c and discontig.c.
I found more issues than this.
1. min_low_pfn and max_low_pfn calculation is inconsistent between
contig.c and discontig.c,
min_low_pfn is calculated as the first page number of boot memmap in
contig.c (Why? Though this may work at the most of the time, I don't
think it is the right logic). It is calculated as the lowest physical
memory page number bypass reserved regions in discontig.c.
max_low_pfn is calculated include reserved regions in contig.c. It is
calculated exclude reserved regions in discontig.c.
2. If kernel code and data region is happen to be at the begin or the
end of physical memory, when min_low_pfn and max_low_pfn calculation is
bypassed kernel code and data, pages in initmem will report bad.
3. initrd is also in reserved regions, if it is at the begin or at the
end of physical memory, kernel will refuse to reuse the memory. Because
the virt_addr_valid check in free_initrd_mem.
So it is better to fix and clean up those issues.
Calculate min_low_pfn and max_low_pfn in a consistent way.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Acked-by: Jay Lan <jlan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The evils of Kconfig's select bite us once again...
ia64/Kconfig selects ACPI, which depends on PM.
But select ignores dependencies, allnoconfig
chooses CONFIG_PM=n, and thus the menu of sub-options
under ACPI vanish, which breaks the build.
Manually select PM along with ACPI for now.
Some day, we should delete them both, or fix select.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In sn_io_slot_fixup(), the parent is re-set from the bus to
io(port|mem)_resource because the address is changed in a way that it's not
child of the bus any more.
However, only the root is set but not the parent/child/sibling relationship
in the resource tree which causes 'cat /proc/iomem' to stop after this
memory area. Depding on the poition in the tree the iomem may be nearly
completely empty.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: John Keller <jpk@sgi.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring defconfig, tiger_defconfig and zx1_defconfig up to date. Also
sprinkle KEXEC and KDUMP combinations around liberally so that my
usual regression test builds will see all combinations:
tiger_defconfig gets KEXEC=y, CRASH_DUMP=n
zx1_defconfig gets KEXEC=n, CRASH_DUMP=y
defconfig gets KEXEC=y, CRASH_DUMP=y
others remain at KEXEC=n, CRASH_DUMP=n
Signed-off-by: Tony Luck <tomy.luck@intel.com>
kdump_find_rsvd_region() is only called by
reserve_memory() which is in __init, so it seems that
kdump_find_rsvd_region() should also be in there.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ptrace misses clearing the syscall trace flag.
The increased syscall overhead is retained after the trace is finished.
This case happens when strace is terminated by force.
Signed-off-by: Akiyama, Nobuyuki <akiyama.nobuyuk@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Grammatical fixes (s/freezed/frozen/)
Make some variables static
Change a C++ "//" comment to "/* ... */"
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Similar to memory error recovery, when a cache error is consumed
by a user process terminate the user instead of crashing the system.
Signed-off-by: Russ Anderson (rja@sgi.com)
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Jack Steiner noticed that duplicate TLB DTC entries do not cause a
linux panic. See discussion:
http://www.gelato.unsw.edu.au/archives/linux-ia64/0307/6108.html
The current TLB recovery code is recovering from the duplicate itr.d
dropins, masking the underlying problem. This change modifies
the MCA recovery code to look for the TLB check signature of the
duplicate TLB entry and panic in that case.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
On 1.6GHz Montectio Tiger4, the following performance data is measured with
kernel built with defconfig which has NUMA configured:
Fastest sys_getcpu: 502 itc counts.
Fastest fsys_getcpu: 28 itc counts.
fsys_getcpu performance is largly impacted by whether data (node_to_cpu_map
etc) is in cache. It can take fsys_getcpu up to ~150 itc counts in cold
cache case.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
efi_initialize_iomem_resources() is declared in both include/linux/efi.h
and arch/ia64/kernel/setup.c. This patch removes the latter.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Berhhard Walle noted that on his HP rx8640 he ended up with saved_max_pfn
smaller than the highest address of system ram in /proc/iomem and proposed
a patch to base the address on the unrounded and unfiltered EFI memory
map address. Simon Horman and Magnus Damm suggested that the whole test
be moved earlier in the function. This is the combination of both of
these patches.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes boot failure because irq_desc->mask() is NULL.
- Added mask/unmask functions to ia64's irq desc function table.
- rename hw_interrupt_type to irq_chip. hw_interrupt_type is old name.
- Tony: Added same change to arch/ia64/sn/kernel/irq.c as pointed out
by Eric Biederman ... mask/unmask functions there can be no-op.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The address where the ELF core header is stored is passed to the secondary
kernel as a kernel command line option. The memory area for this header is
also marked as a separate EFI memory descriptor on ia64.
The separate EFI memory descriptor is at the moment of the type
EFI_UNUSABLE_MEMORY. With such a type the secondary kernel skips over the
entire memory granule (config option, 16M or 64M) when detecting memory.
If we are lucky we will just lose some memory, but if we happen to have
data in the same granule (such as an initramfs image), then this data will
never get mapped and the kernel bombs out when trying to access it.
So this is an attempt to fix this by changing the EFI memory descriptor
type into EFI_LOADER_DATA. This type is the same type used for the kernel
data and for initramfs. In the secondary kernel we then handle the ELF
core header data the same way as we handle the initramfs image.
This patch contains the kernel changes to make this happen. Pretty
straightforward, we reserve the area in reserve_memory(). The address for
the area comes from the kernel command line and the size comes from the
specialized EFI parsing function vmcore_find_descriptor_size().
The kexec-tools-testing code for this can be found here:
http://lists.osdl.org/pipermail/fastboot/2007-February/005983.html
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Perfmon associates vmalloc()ed memory with a file descriptor, and installs
a vma mapping that memory. Unfortunately, the vm_file field is not filled
in, so processes with mappings to that memory do not prevent the file from
being closed and the memory freed. This results in use-after-free bugs and
multiple freeing of pages, etc.
I saw this bug on an Altix on SLES9. Haven't reproduced upstream but it
looks like the same issue is there.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add VERIFY_WRITE check in the beginning like compat_sys_getdents() (EINVAL vs
EFAULT).
Signed-off-by: Alexandr Andreev <aandreev@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Always build ia64 xor.o because multiple config options now depend on it.
Necessary to build .20-mm* on ia64 when, e.g., CONFIG_ASYNC_TX_DMA is
defined. Don't know if '_ASYNC_TX_DMA makes sense on ia64. If not, maybe
Kconfig should preclude it.
Could have defined a Kconfig option that defaults to true if MD_RAID456 ||
ASYNC_TX_DMA to control building of xor.o, but xor.o is only 848 bytes and
this IS ia64...
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make saved_max_pfn point to max_pfn of entire system.
Without this patch is so that vmcore is zero length on ia64. This is
because saved_max_pfn was wrongly being set to the max_pfn of the crash
kernel's address space, rather than the max_pfg on the physical memory of
the machine - the whole purpose of vmcore is to access physical memory that
is not part of the crash kernel's addresss space.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Sort-Of-Acked-By: Jay Lan <jlan@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
To provide compatibilty with SN kernels that do and do not
have ACPI IO support, the SN PROM must build different
versions of some ACPI tables based on which kernel is booting.
As such, the tables may have to change at kernel boot time.
By default, prior to kernel boot, the PROM builds an empty
DSDT (header only) and no SSDTs. If an ACPI capable kernel
boots, the kernel will notify the PROM, at platform setup time,
and the PROM will build full DSDT and SSDT tables.
With the latest changes to acpi_table_init(), the table lengths
are saved, and when our PROM changes them, the changes are not seen,
and the kernel will crash on boot. Because of issues with kexec support,
we are not able to create the tables prior to acpi_table_init().
As a result, we are making a second call to acpi_table_init() to
process the rebuilt DSDT and SSDTs.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch replaces all instances of "set_native_irq_info(irq, mask)"
with "irq_desc[irq].affinity = mask". The latter form is clearer
uses fewer abstractions, and makes access to this field uniform
accross different architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SN code to initialize the Hub/TIO infrastructure needs to
execute before bus scanning. This was previously done with
an early call to acpi_bus_register_driver(). But now that
ACPI is using the Linux driver model, a driver cannot be registered
that early. Make changes to have the init routines invoked via
calls to acpi_get_devices().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
Fix "spin_lock_irqrestore" to "spin_unlock_irqrestore."
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
acpi_boot_init() is making a bad check on the return
status from acpi_table_parse(). acpi_table_parse() now
returns zero on success, one on failure.
Signed-off-by: Aaron Young <ayoung@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If an ATA drive uses legacy mode, ata driver will choose 14 and 15
as the fixed irq number. On ia64 platform, such numbers are GSI and
should be converted to irq vector.
Below patch against kernel 2.6.20 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This convters the sysctl ctl_tables to use C99 initializers. While I was
looking at it I discovered it was using a portion of the sysctl binary
addresses space under CTL_KERN KERN_OSTYPE which was completely inappropriate.
So I completely removed all of the sysctl binary names, to remove and avoid
the ABI conflict.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By not using the enumeration in sysctl.h (or even understanding it) the SN
platform placed their arch specific xpc directory on top of CTL_KERN and only
because they didn't have 4 entries in their xpc directory got lucky and didn't
break glibc.
This is totally irresponsible. So this patch entirely removes sys_sysctl
support from their sysctl code. Hopefully they don't have ascii name
conflicts as well.
And now that they have no ABI numbers add them to the end instead of the
sysctl list instead of the head so nothing else will be overridden.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove in-source externs, linux/init.h is included in all cases.
This is a fixups for "Dynamic kernel command-line" patch.
It also includes some uml __init fixups so that we can __initdata also its
command_line.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Rename saved_command_line into boot_command_line.
2. Set command_line as __initdata.
[akpm@osdl.org: move some declarations to the right place]
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Part of long forgotten patch
http://groups.google.com/group/fa.linux.kernel/msg/e98e941ce1cf29f6?dmode=source
Since then, m32r grabbed two copies.
Leave s390 copy because of important absence of CONFIG_VT, but remove
references to non-existent timerlist_lock. ia64 also loses timerlist_lock.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix-rmmod-read-write-races-in-proc-entries.patch doesn't want dynamically
allocated ->proc_fops, because it will set it to NULL at module unload time.
Regardless of module status, switch to statically allocated ->proc_fops which
leads to simpler code without wrappers.
AFAICS, also fix the following bug: "sn_force_interrupt" proc entry set
->write for itself, but was created with 0444 permissions. Change to 0644.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that almost all architectures implemented exactly the same
sys32_sysinfo... except parisc, where a bug was to be found in handling of
the uptime. So let's remove a whole whack of code for fun and profit.
Cribbed compat_sys_sysinfo from x86_64's implementation, since I figured it
would be the best tested.
This patch incorporates Arnd's suggestion of not using set_fs/get_fs, but
instead extracting out the common code from sys_sysinfo.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update all arch/*/kernel/vmlinux.lds.S to not include space for initramfs
when CONFIG_BLK_DEV_INITRAMFS is not selected. This saves another 4 kbytes
on most platfoms (some reserve PAGE_SIZE for initramfs).
Signed-off-by: Jean-Paul Saman <jean-paul.saman@nxp.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ZONE_DMA less operation for IA64 SGI platform
Disable ZONE_DMA for SGI SN2. All memory is addressable by all devices and we
do not need any special memory pool.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch simply defines CONFIG_ZONE_DMA for all arches. We later do special
things with CONFIG_ZONE_DMA after the VM and an arch are prepared to work
without ZONE_DMA.
CONFIG_ZONE_DMA can be defined in two ways depending on how an architecture
handles ISA DMA.
First if CONFIG_GENERIC_ISA_DMA is set by the arch then we know that the arch
needs ZONE_DMA because ISA DMA devices are supported. We can catch this in
mm/Kconfig and do not need to modify arch code.
Second, arches may use ZONE_DMA in an unknown way. We set CONFIG_ZONE_DMA for
all arches that do not set CONFIG_GENERIC_ISA_DMA in order to insure backwards
compatibility. The arches may later undefine ZONE_DMA if their arch code has
been verified to not depend on ZONE_DMA.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Function is unnecessary now. We can use the summing features of the ZVCs to
get the values we need.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arch hooks arch_setup_msi_irq and arch_teardown_msi_irq are now
responsible for allocating and freeing the linux irq in addition to
setting up the the linux irq to work with the interrupt.
arch_setup_msi_irq now takes a pci_device and a msi_desc and returns
an irq.
With this change in place this code should be useable by all platforms
except those that won't let the OS touch the hardware like ppc RTAS.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to be able to get from an irq number to a struct msi_desc.
The msi_desc array in msi.c had several short comings the big one was
that it could not be used outside of msi.c. Using irq_data in struct
irq_desc almost worked except on some architectures irq_data needs to
be used for something else.
So this patch adds a msi_desc pointer to irq_desc, adds the appropriate
wrappers and changes all of the msi code to use them.
The dynamic_irq_init/cleanup code was tweaked to ensure the new
field is left in a well defined state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (140 commits)
ACPICA: reduce table header messages to fit within 80 columns
asus-laptop: merge with ACPICA table update
ACPI: bay: Convert ACPI Bay driver to be compatible with sysfs update.
ACPI: bay: new driver is EXPERIMENTAL
ACPI: bay: make drive_bays static
ACPI: bay: make bay a platform driver
ACPI: bay: remove prototype procfs code
ACPI: bay: delete unused variable
ACPI: bay: new driver adding removable drive bay support
ACPI: dock: check if parent is on dock
ACPICA: fix gcc build warnings
Altix: Add ACPI SSDT PCI device support (hotplug)
Altix: ACPI SSDT PCI device support
ACPICA: reduce conflicts with Altix patch series
ACPI_NUMA: fix HP IA64 simulator issue with extended memory domain
ACPI: fix HP RX2600 IA64 boot
ACPI: build fix for IBM x440 - CONFIG_X86_SUMMIT
ACPICA: Update version to 20070126
ACPICA: Fix for incorrect parameter passed to AcpiTbDeleteTable during table load.
ACPICA: Update copyright to 2007.
...
Instead of pinning per-cpu TLB into a DTR, use DTC. This will free up
one TLB entry for application, or even kernel if access pattern to
per-cpu data area has high temporal locality.
Since per-cpu is mapped at the top of region 7 address, we just need to
add special case in alt_dtlb_miss. The physical address of per-cpu data
is already conveniently stored in IA64_KR(PER_CPU_DATA). Latency for
alt_dtlb_miss is not affected as we can hide all the latency. It was
measured that alt_dtlb_miss handler has 23 cycles latency before and
after the patch.
The performance effect is massive for applications that put lots of tlb
pressure on CPU. Workload environment like database online transaction
processing or application uses tera-byte of memory would benefit the most.
Measurement with industry standard database benchmark shown an upward
of 1.6% gain. While smaller workloads like cpu, java also showing small
improvement.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It's not efficient to use a per-cpu variable just to store
how many physical stack register a cpu has. Ever since the
incarnation of ia64 up till upcoming Montecito processor, that
variable has "glued" to 96. Having a variable in memory means
that the kernel is burning an extra cacheline access on every
syscall and kernel exit path. Such "static" value is better
served with the instruction patching utility exists today.
Convert ia64_phys_stacked_size_p8 into dynamic insn patching.
This also has a pleasant side effect of eliminating access to
per-cpu area while psr.ic=0 in the kernel exit path. (fixable
for per-cpu DTC work, but why bother?)
There are some concerns with the default value that the instruc-
tion encoded in the kernel image. It shouldn't be concerned.
The reasons are:
(1) cpu_init() is called at CPU initialization. In there, we
find out physical stack register size from PAL and patch
two instructions in kernel exit code. The code in question
can not be executed before the patching is done.
(2) current implementation stores zero in ia64_phys_stacked_size_p8,
and that's what the current kernel exit path loads the value with.
With the new code, it is equivalent that we store reg size 96
in ia64_phys_stacked_size_p8, thus creating a better safety net.
Given (1) above can never fail, having (2) is just a bonus.
All in all, this patch allow one less memory reference in the kernel
exit path, thus reducing syscall and interrupt return latency; and
avoid polluting potential useful data in the CPU cache.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes
- marking I-cache clean of pages DMAed to now only done for IA64
- broken multiple inclusion in include/asm-x86_64/swiotlb.h
- missing call to mark_clean in swiotlb_sync_sg()
- a (perhaps only theoretical) issue in swiotlb_dma_supported() when
io_tlb_end is exactly at the end of memory
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
getcpu system call returns cpu# and node# on which this system call and
its caller are running. This patch hooks up its implementation on IA64.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Eliminate arch specific memory_present call ia64 NUMA by utilizing
sparse_memory_present_with_active_regions.
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On the ia64 architecture only this patch upgrades show_mem() for sparse
memory to be the same as it was for discontig memory. It has been shown to
work on NUMA and flatmem architectures.
Signed-off-by: George Beshers <gbeshers@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add missing exports to allow several drivers to be built as module with
CONFIG_IA64_HP_ZX1_SWIOTLB.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Occasionally the FSYS_RETURN patch list can have an odd length, causing other
data structures to get out of alignment. In OpenVZ it is odd and we get
misaligned kernel image, which does not boot.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
While pursuing and unrelated issue with 64Mb granules I noticed a problem
related to inconsistent use of add_active_range. There doesn't appear any
reason to me why FLATMEM versus DISCONTIG_MEM should register memory to
add_active_range with different code. So I've changed the code into a
common implementation.
The other subtle issue fixed by this patch was calling add_active_range in
count_node_pages before granule aligning is performed. We were lucky with
16MB granules but not so with 64MB granules. count_node_pages has reserved
regions filtered out and as a consequence linked kernel text and data
aren't covered by calls to count_node_pages. So linked kernel regions
wasn't reported to add_active_regions. This resulted in free_initmem
causing numerous bad_page reports. This won't occur with this patch
because now all known memory regions are reported by
register_active_ranges.
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Don't force CONFIG_SWIOTLB on when not actually needed (i.e. HP_ZX1 and
SGI_SN2).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When we offline a CPU, migrate_irqs() tries to determine whether the
affinity bits of the IRQ descriptor match any of the remaining online
CPUs. If not, it fixes up the interrupt to point somewhere else.
Unfortunately, if an IRQ is unregistered the IRQ descriptor may still
have affinity to the CPU being offlined, but the no_irq_chip handler
doesn't provide a set_affinity function. This causes us to hit the
WARN_ON in migrate_irqs().
The easiest solution seems to be setting all the bits in the affinity
mask when the last interrupt is removed from the vector. I hit this on
an older kernel with Xen/ia64 using driver domains (so it probably needs
more testing on upstream). Xen essentially uses the bind/unbind
interface in sysfs to unregister a device from a driver and thus
unregister the interrupt.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
All IA64 systems except IA64_HP_SIM include ACPI and PCI.
So prevent IA64 Kconfigs that try to do irritating things like building
PCI without building ACPI.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes a NULL-pointer dereference in ia64_machine_kexec().
The variable ia64_kimage is set in machine_kexec_prepare() which is
called from sys_kexec_load(). If kdump wasn't configured before,
ia64_kimage is NULL. machine_kdump_on_init() passes ia64_kimage() to
machine_kexec() which assumes a valid value.
The patch also adds a few sanity checks for the image to simplify
debugging of similar problems in future.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I encountered one problem when running ptrace test case the situation
is this: traced process's syscall parameter needs to be accessed, but
for sys_clone system call with clone_flag (CLONE_VFORK | CLONE_VM |
SIGCHLD) parameter. This syscall's parameter accessing result is wrong.
The reason is that vforked child process mm point is the same, but
tgid is different. Without this patch find_thread_for_addr will return
vforked process if vforked process is also stopped, but not the thread
which calls vfork syscall.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some patches have turned up on xen-devel recently to convert strcpy()
to safer alternatives and so forth. While reviewing those patches
I noticed that the features string building could be cleaned up.
This patch uses snprintf() instead of strcpy() and direct character
pointer manipulation. It makes the features string building safe and
gets rid of the special case for features output in show_cpuinfo()
Additionally I removed the (int) cast of ARRAY_SIZE, which seems to
serve no purpose.
Signed-off-by: Aron Griffis <aron@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As is pointed out in
http://www.gelato.org/community/view_linear.php?id=1_1036&from=authors&value=Ian%20Wienand#1_1039,
if single step on break instruction, the break fault has higher
priority than the single-step trap. When the break fault handler
is entered, it advances the IP by 1 instruction so break instruction
single-stepping is skipped, actually it is next instruction which
is single stepped.
This patch modifies this, it adds TIF_SINGLESTEP bit for thread
flags, and generate a fake sigtrap when single stepping break
instruction. Test case in attachment can verify this. Any comments
is welcome.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This moves the ia64 implementation of machine_shutdown() from
machine_kexec.c to process.c, which is in keeping with the implelmentation
on other architectures, and seems like a much more appropriate home for it.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove the Remove inline declaration of efi_get_pal_addr() as it is
declared in linux/efi.h.
Signed-Off-By: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
linux/uaccess.h was being included, but it seems that
really the following includes are needed.
asm/page.h: for __va() and PAGE_SHIFT
asm/uaccess.h: for copy_to_user()
I guess that linux/uaccess.h pulls in both asm/page.h and asm/uaccess.h.
I notices this while backporting the code to xen's linux-2.6.16.33,
which does not have linux/uaccess.h. I'm posting it as I think it is a
correct, though somewhat cosmetic fix.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a typo in the saved_max_pfn description in contig.c
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Set saved_max_pfn when discontig memory is in use.
This sets up saved_max_pfn when disctontig memory is in use.
This mirrors the code for contig memory.
This patch does not entirely solve the problem of making vmcore work,
however it does appear to be neccessary. Please consider applying.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Kexec support for 2.6.20 on ia64 does not build properly using a config
made up by CONFIG_SMP=n and CONFIG_HOTPLUG_CPU=n:
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Jay Lan <jlan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SN Altix platform does not conform to the IOSAPIC IRQ routing model.
Add code in acpi_unregister_gsi() to check if (acpi_irq_model ==
ACPI_IRQ_MODEL_PLATFORM) and return.
Due to an oversight, this code was not added previously when
similar code was added to acpi_register_gsi().
http://marc.theaimsgroup.com/?l=linux-acpi&m=116680983430121&w=2
Signed-off-by: John Keller <jpk@sgi.com>
Acked-by: Len Brown <lenb@kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes up ia64 kexec support for HP rx2620 hardware. It does
this by skipping migration of already disabled irqs. This is most likely a
problem on other ia64 platforms as well, but I've only been able to
reproduce it on one machine so far.
The full story is that handle_bad_irq() gets invoked before starting the
new kernel without this patch. This seems to happen when fixup_irqs()
calls generic_handle_irq() on already migrated (and disabled) irqs. So by
avoiding migration of disabled irqs we stay away of handle_bad_irq().
The code has been tested on three different ia64 machines, all with good
results. It is possible to trigger the same bug by offlining a processor
using echo 0 > /sys/devices/system/cpu/cpuX/online.
More detailed information is available in the following mail thread:
http://lists.osdl.org/pipermail/fastboot/2007-January/thread.html#5774
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Zou, Nanhai <nanhai.zou@intel.com>
Acked-by: Jay Lan <jlan@sgi.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SN platform support for running with an ACPI
capable PROM that defines PCI devices in SSDT
tables. There is a SSDT table for every occupied
slot on a root bus, containing info for every
PPB and/or device on the bus. The SSDTs will be
dynamically loaded/unloaded at hotplug enable/disable.
Platform specific information that is currently
passed via a SAL call, will now be passed via the
Vendor resource in the ACPI Device object(s) defined
in each SSDT.
Signed-off-by: John Keller <jpk@sgi.com>
Cc: Greg KH <greg@kroah.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI 3.0 incorporated the SRAT spec, upping the table version to 2,
and extending the size of the proximity domain from 1-byte to 4-bytes.
This extension was into a reserved field that firmware should
set to 0, but the HP simulator had non-zero values there
resulting in unexpected huge numbers.
So mask the domain down to 8-bits for now.
A more general fix will be to check the table version
supplied by firmware and get paranoid about reserved fields.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This kernel driver patch provides sysfs interface for user application to
call pal_mc_error_inject() procedure.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch has kenrel configuration changes for the MC Error Injection
Tool.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
Revert "ACPI: ibm-acpi: make non-generic bay support optional"
ACPI: update MAINTAINERS
ACPI: schedule obsolete features for deletion
ACPI: delete two spurious ACPI messages
ACPI: rename cstate_entry_s to cstate_entry
ACPI: ec: enable printk on cmdline use
ACPI: Altix: ACPI _PRT support
Fix an oops experienced on the Cell architecture when init-time functions,
early_*(), are called at runtime. It alters the call paths to make sure
that the callers explicitly say whether the call is being made on behalf of
a hotplug even, or happening at boot-time.
It has been compile tested on ppc64, ia64, s390, i386 and x86_64.
Acked-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
