Replace use of lpfc_put_lun with midlayer's int_to_scsilun
Remove driver's local definition of lpfc_put_lun (which converts an
int back to a 64-bit LUN) and replace it's use with the recently added
int_to_scsilun function provided by the midlayer.
Note: Embedding midlayer structure in our structure caused
need for more files to include midlayer headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix handling of the dev_loss and nodev timeouts.
Symptoms: when remote port disappears for a period of time longer then
either nodev_tmo or dev_loss_tmo, the lpfc driver worker thread will
stall removing that remote port.
Cause: removing remote port involves un-blocking and sync-ing
corresponding block device queue. But corresponding node in the lpfc
driver is still in the NPR(?node port recovery?) state and mid-layer
gets SCSI_MLQUEUE_HOST_BUSY as a return value when it is trying to call
queuecommand() with command for that node (AKA remote port)
Fix: Instead of returning SCSI_MLQUEUE_HOST_BUS from queuecommand() for
nodes in NPR states complete it with retry-able error code DID_BUS_BUSY
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic in lpfc_get_stats()
Symptoms: Panic on sysfs stats access
Cause: In lpfc_get_stats() we are writing to memory that we do not
own.
Fix: Fix our stats structure allocation. Embed phba->link_stats in
struct lpfc_hba and stop treating it like rogue structure.
Note: Embedding midlayer/transport structure in our structure caused
need for more files to include midlayer/transport headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clear task management bits when preparing SCSI commands
In lpfc_scsi_prep_cmnd, clear the task management bits (fcpCntl2 member
in the fcp_cmd structure) when preparing regular SCSI commands.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic on lip and cable pull
Symptoms: Panic on lip or cable pull
Cause: Use after free of nlp in lpfc_nlp_remove()
Fix: Do not make FC transport calls after a node is removed. Transport
calls are disabled by ignoring the initial delete transition.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IOCB BDE not getting fully initialized during reuse
Symptoms: Driver gets Status 3 and Reason 0x13 on IOCB completions.
Cause: The IOCB bpl.bdeSize and bdeFlags are not getting initialized on reuse.
Fix: Reinitialize these fields in prep_dma each time an IOCB is used.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Steve Wilcox <spwilcox@att.com>
In order to properly report LUN's > 7, the DEC HSG80 definition in
scsi_devinfo.c needs to include BLIST_REPORTLUN2 rather than
BLIST_SPARSELUN. I've tested this change with several HSG firmware
revisions and with both Emulex and Qlogic HBA's.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
PATCH 2/2: handle the case when device returns/needs extra data
Description:
Sometimes the device returns/needs extra data than expected.
Changes:
Modify __atapi_pio_bytes() to handle the case where device returns/needs extra data.
- for read case, discard trailing data from the device
- for write case, padding zero data to the device
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PATCH 1/2: ata_data_xfer() fix
Changes:
- Modify ata_mmio_data_xfer() and ata_pio_data_xfer() to handle odd-lengthed buffer.
- Add some function comments
This patch does not reuse ap->pad as alignment buffer since
using local variable seems good enough.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hello,
This patch adds the Intel ICH7-M DH DID to the ahci.c file for AHCI mode SATA support. This patch was built against the 2.6.13-rc6 kernel.
If acceptable, please apply.
Thanks,
Jason Gaston
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sata_sx4 directly references sg->length to calculate total_len in
pdc20621_dma_prep(). This is incorrect as dma_map_sg() could have
merged multiple sg's into one and, in such case, sg->length doesn't
reflect true size of the entry. This patch makes it use
sg_dma_len(sg).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There's a spurious (and illegal since it's marked __exit) call to
ahc_linux_exit() in ahc_linux_init() which causes a double list
deletion of the transport class; remove it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Originally From: Andrew Morton <akpm@osdl.org>
Altered By: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
There is an additional 'build fix' patch that Andrew Morton submitted on
the kernel list (I have changed out his dpr_i2o with dpt_i2o below
though).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When run on a kernel that scans all LUNs, a certain crappy
scsi scanner reports the same LUN over and over..
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=155457
Aparently they were so shamed by this, they chose to remain
anonymous. Though it seems the blacklist code handles
anonymous vendors just fine.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have some nasty issues with 2.6.12-rc6. Any request to scan on
the lpfc or qla2xxx FC adapters will oops. What is happening is the
system is defaulting to non-transport registered targets, which
inherit the parent of the scan. On this second scan, performed by
the attribute, the parent becomes the shost instead of the rport.
The slave functions in the 2 FC adapters use starget_to_rport()
routines, which incorrectly map the shost as an rport pointer.
Additionally, this pointed out other weaknesses:
- If the target structure is torn down outside of the transport,
we have no method for it to be regenerated at the proper parent.
- We have race conditions on the target being allocated by both
the midlayer scan (parent=shost) and by the fc transport
(parent=rport).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
This patch adds the product ID for the ICP9067MA adapter.
The entries for the ICP9085LI, ICP5085BR, IBM8k & ASR4810SAS were
incorrect and would not initialize the adapters correctly.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Prevent driver from loading if another driver (i2o) has already claimed
the resources associated with the card. Discussion associated with this
bug can be referenced at http://bugzilla.kernel.org/show_bug.cgi?id=4940
where it was agreed to use pci_request_regions in both the dpt_i2o and
the i2o driver to prevent both drivers loading on the same adapter(s).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are certain rogue devices (and the aic7xxx driver) that return
BUSY or QUEUE_FULL forever. This code will apply a global timeout (of
the total number of retries times the per command timer) to a given
command. If it is exceeded, the command is completed regardless of its
state.
The patch also removes the unused field in the command: timeout and
timeout_total.
This solves the problem of detecting an endless loop in the mid-layer
because of BUSY/QUEUE_FULL bouncing, but will not recover the device.
In the aic7xxx case, the driver can be recovered by sending a bus reset,
so possibly this should be tied into the error handler?
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I have rediffed the patch against 2.6.13-rc5, done a couple of cosmetic
cleanups, and run some tests. Brian King has acknowledged that it fixes the
problems he has seen. Seems mature enough for inclusion into 2.6.14 (or
later)?
Nate's explanation of the changes:
I've attached patches against 2.6.13rc2. These are basically identical
to my earlier patches, as I found that all issues I'd seen in earlier
kernels still existed in this kernel.
To summarize, the changes are: (more details in my original email)
- add a kref to the scsi_tape structure, and associate reference
counting stuff
- set sr_request->end_io = blk_end_sync_rq so we get notified when an IO
is rejected when the device goes away
- check rq_status when IOs complete, else we don't know that IOs
rejected for a dead device in fact did not complete
- change last_SRpnt so it's set before an async IO is issued (in case
st_sleep_done is bypassed)
- fix a bogus use of last_SRpnt in st_chk_result
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The cmd->timeout field has been obsolete for a while now. While looking
to remove it, I came across this use in the aacraid driver. It looks
like you want to initialise the firmware with the current timeout of the
command (in seconds), so the value I think you should be using is
cmd->timeout_per_command.
Acked by: Mark Haverkamp <markh@osdl.org>
Acked by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
without it you get this failure:
drivers/built-in.o(.text+0xdcccd): In function `ahd_linux_slave_configure':
drivers/scsi/aic7xxx/aic79xx_osm.c:636: undefined reference to `spi_dv_device'
drivers/built-in.o(.text+0xdd7b1): In function `ahd_send_async':
drivers/scsi/aic7xxx/aic79xx_osm.c:1652: undefined reference to `spi_display_xfer_agreement'
drivers/built-in.o(.init.text+0x7b4d): In function `ahd_linux_init':
drivers/scsi/aic7xxx/aic79xx_osm.c:2765: undefined reference to `spi_attach_transport'
drivers/built-in.o(.init.text+0x7c94):drivers/scsi/aic7xxx/aic79xx_osm.c:2774: undefined reference to `spi_release_transport'
drivers/built-in.o(.exit.text+0x72c): In function `ahd_linux_exit':
drivers/scsi/aic7xxx/aic79xx_osm.c:2783: undefined reference to `spi_release_transport'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
This patch adds support for the new raw io command. This new command
offers much larger io commands, is more friendly to the internal firmware
structure requiring less translation efforts by the firmware and offers
support for targets greater than 2TB (patch to support >2TB will
be sent in the future).
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
If the Adapter is quiet and does not produce an AIF event packets to be
picked up by the management applications for longer than the timeout
interval of two minutes, the cleanup code that deals with aging out
registrants could erroneously drop the registration. The timeout is
there to clean up should the management application die and fail to poll
for updated AIF event packets.
Moving the timer update from the ioctl code that delivers an AIF to the
polling registrant to the bottom of the ioctl means the timeout is reset
with any management application polling activity regardless if an AIF is
delivered or not removing the erroneous timeout cleanups.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
This patch removes the duplicate code in the write_callback command
completion handler, and renames read_callback to io_callback. Optimized
the lba calculation into the debug print routine macro to optimize the
i/o code path.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add in pci shutdown method so that the adapter shuts down correctly and
flushes its cache. Shutdown should also disable the adapter's interrupt
when shutdown (in particularly if the driver is rmmod'd) to prevent
spurious hardware activities.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
Fixes a bug in check_revision. It should return the driver version not
the firmware version.
Update driver version number.
Update driver version string.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
If more than two commands are outstanding to the controller, there is no
need to notify the adapter via a PCI bus transaction of additional
commands added into the queue; it will get to them when it works through
the produce/consumer indexes.
This reduced the PCI traffic in the driver to submit a command to the
queue to near zero allowing a significant number of commands to be
turned around with no need to block for the PCI bridge to flush the
notify request to the adapter.
Interrupt mitigation has always been present in the driver; it was
turned off because of a bug that prevented one from realizing the
usefulness of the feature. This bug is fixed in this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch upports all relevant code fixes and bumps the driver version
to 7.0 to signify starting a new tree.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this patch is just a cross-port of the fixup for aic7xxx DT settings.
As the same restrictions apply for aic79xx also (DT requires wide
transfers) the dt setting routine should be modified equivalently.
And an invalid period setting will be caught by ahd_find_syncrate()
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Several people noticed we dropped quite a bit on benchmark figures.
OK, it was my fault but unfortunately I discovered I ran out of brown
paper bags a while ago and forgot to reorder them.
The issue is that a construct introduced in the conversion of the
driver to use the transport class keyed off whether the block request
was tagged or not. However, the aic7xxx driver doesn't properly set
up the block layer TCQ (it uses the wrong API), so the driver now
things all requests are untagged and we keep it to a queue depth of a
single element. Oops.
The fix is to use the correct TCQ API.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This parameter is important only to people who take the time to tune the
margin control settings, otherwise it's completely irrelevant. However,
just in case anyone should want to do this, it's appropriate to include
the parameter.
I don't do anything with it in DV by design, so the parameter will come
up as off by default, so if anyone actually wants to play with the
margin control settings they'll have to enable it under the
spi_transport class first.
I also updated the transfer settings display to report all of the PPR
settings instead of only DT, IU and QAS
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a slight problem in the way you've done the transport
parameters; reading from the variables actually produces the current
settings, not the ones you just set (and there's usually a lag because
devices don't renegotiate until the next command goes over the bus). If
you set the bit immediately, you get into the situation where the
transport parameters report something as being set even if the drive
cannot support it.
I patched the driver to do it this way and also corrected a panic in the
proc routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates various scsi_transport_spi parameters with the actual
parameters used by the driver internally.
Domain Validation for all devices should now work properly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the aic79xx driver to take advantage of the
scsi_transport_spi infrastructure. Patch is quite a mess as some
procedures have been reshuffled to be closer to the aic7xxx driver.
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Jeff Garzik <jgarzik@pobox.com>
This patch removes the busyq in aic79xx and uses the command-queue from
the midlayer instead. Additionally some dead code is removed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Fixed rejections
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
we have the most recent microcode, make sure to always load it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The aic7xxx can support Data Group transfers at periods > 12.5, so
eliminate that restriction. Additionally wide is a requirement for DT
so ensure wide is set if users request DT.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rebuild the aic7xxx firmware doesn't work anymore after this change
which appeared int 2.6.13-rc1:
[SCSI] aic7xxx/aic79xx: remove useless byte order macro cruft
Two files did not include byteorder.h, resulting in aic dying with a panic
"Unknown opcode encountered in seq program"
This fixes it for me.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removing the SCSI tape module results in an oops in class_device_destroy if
any devices are present. The patch at the end of this message fixes the bug
by moving class_destroy() later in exit_st() so that the class still exists
when devices are removed. (The bug is old but class_simple_device_remove() did
nothing when the class did not exist.)
The patch also fixes a "class leak" in init_st() error path.
I would like to get this into 2.6.13 but it may be too late?
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I am resubmitting the 2.6 kernel patch for the Version 7.12.02 ips driver.
I have eliminated a couple of inappropriate changes pointed out by Arjan.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Martin Drab found that he could get aacraid timeouts with high load on his
controller / disk drive combinations. After some experimentation Mark
Salyzyn has come up with a patch to reduce the default max_sectors to
something that will keep the controller from being overloaded and will
eliminate the timeout issues.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SCSI=m must disallow static drivers.
The problem is that all the SATA drivers depend on SCSI_SATA.
With SCSI=m and SCSI_SATA=y this allows the static enabling of the SATA
drivers with unwanted effects, e.g.:
- SCSI=m, SCSI_SATA=y, SCSI_ATA_ADMA=y
-> SCSI_ATA_ADMA is built statically but scsi/built-in.o is not linked
into the kernel
- SCSI=m, SCSI_SATA=y, SCSI_ATA_ADMA=y, SCSI_SATA_AHCI=m
-> SCSI_ATA_ADMA and libata are built statically but
scsi/built-in.o is not linked into the kernel,
SCSI_SATA_AHCI is built modular (unresolved symbols due to missing
libata)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support to not allow additions to a host when it is being removed.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the old scsi_host_cancel function as it has not been working for
sometime do to the device list possibly being empty when it is called and
possible race issues. Add setting of SHOST_CANCEL at the state of beginning
of scsi_remove_host.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Migrate the current SCSI host state model to a model like SCSI
device is using.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Basically DT isn't reported or handled at all. The problem is that
lines of code like this:
spi_dt(starget) = tinfo->curr.ppr_options & MSG_EXT_PPR_DT_REQ;
don't do what you think they do when spi_dt is a single bit variable.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It seems very unlikely that this driver will go into any stable kernel
before devfs will be removed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
aic doesnt work anymore after this change which appeared int 2.6.13-rc1:
[SCSI] aic7xxx/aic79xx: remove useless byte order macro cruft
2 files did not include byteorder.h, aic died with panic
"Unknown opcode encountered in seq program"
This patch fixes it for me.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes srp.h which uses 0x80 for SRP_LOGIN_REJ instead of
0xc2.
Signed-off-by: Linda Xie <lxie@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds functionality to check the PCI sub-class code of an
AHCI capable device before disabling AHCI. It fixes a bug where an
ICH7 sata controller is being setup by the BIOS as sub-class 1 (ide)
and the AHCI control registers weren't being initialized, thus causing
an IO error in piix_disable_ahci().
Signed-off-by: Gregory Felix <greg.felix@gmail.com>
This adds the appropriate FW_LOADER pre-requisite and a separate entry
for ISP24xx support.
Thanks to Adrian Bunk and Jesper Juhl for their efforts in fixing this
quirk.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we haven't configured the qla24xx driver, then the Makefile shouldn't
do it for us.
This also means that we can avoid the unnecessary selection of FC_ATTRS.
Debugged by James Bottomley
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a missing check for an error return code from scsi_sysfs_add_sdev.
This resolves entry #4863 in the OSDL bugzilla. Although in that bug
report the failure occurred because of a confusion over scanning vs.
rescanning, in general add_sdev can fail for a number of reasons (the
simplest being insufficient memory) and the caller should cope properly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Older gcc's dont support anonymous unions, so this driver gets hundreds of
error.
Fortunately the fix is easy...
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was going over the scsi I/O submit path, when sd_init_command
construct the scsi command, this_count is already checked in the
previous else if clause. Why does it need to check it again in
the last else block?
Patch to delete the spurious check.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_init_io calls scsi_alloc_sgtable and then calls blk_rq_map_sg
to initialize the scatterlist structure. blk_rq_map_sg() already
memset the structure for every new segment. That makes the memset
in scsi_alloc_sgtable unnecessary.
Patch to delete the extra memset in scsi_alloc_sgtable. Tested on
a x86_64 machine. Looks stable to me.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the issues we had was reverting the midlayers lun value
into the 8byte lun value that we wanted to send to the device.
Historically, there's been some combination of byte swapping,
setting high/low, etc. There's also been no common thread between
how our driver did it and others. I also got very confused as
to why byteswap routines were being used.
Anyway, this patch is a LLDD-callable function that reverts the
midlayer's lun value, stored in an int, to the 8-byte quantity
(note: this is not the real 8byte quantity, just the same amount
that scsilun_to_int() was able to convert and store originally).
This also solves the dilemma of the thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=112116767118981&w=2
A patch for the lpfc driver to use this function will be along
in a few days (batched with other patches).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanup FC remote port registration.
Due to the inherent behaviour (an immediate scan) of adding
a 'target'-role-capable rport via fc_remote_port_add(),
split the registration into two steps -- addition as
unknown-type role, then use fc_remote_port_rolchg() with
appropriate role (based on PLOGI/PRLI bits). This allows
for a more cleaner rport->dd_data management as can be seen
with the simplified qla2xxx_slave_alloc() function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Consolidate ISP24xx chip reset logic.
Consolidate near-duplicate RISC reset logic from
qla24xx_reset_chip() and qla24xx_chip_diag(). Also, after
initiating a soft-reset, insure the firmware has completed
all NVRAM accesses before continuing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add firmware version number to qla24xx_fw_version_str().
Original code was accidently trimmed during port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The wrong sgmap structure is being assigned in aac_send_raw_srb.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update version number to 8.01.00b5-k.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct maximum supported lun and target-id definitions.
The driver uses command-IOCBs which support a maximum lun
value of 0xffff -- correct #define to reflect the change.
Also, remove superfluous MAX_TARGET definition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NVRAM id-list updates.
Resync with latest NVRAM subsystem ID list.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add OS initialization codes for ISP24xx recognition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx ISR routines.
Add appropriate glue-code for ISP24xx support -- this
included generalizing some of the core handling
routines (qla2x00_async_event() [pull-up retrieval of
mailbox values] and qla2x00_status_entry()]. Fixup
2100/2300 ISRs to handle the new conventions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx IOCB manipulation routines.
Add appropriate glue-code for ISP24xx support while
manipulting IOCB packets. Add an ISP24xx specific
'start_scsi' routine due to command-type-7 layout
changes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx flash-manipulation routines.
Add read/write flash manipulation routines for the ISP24xx.
Update sysfs NVRAM objects to use generalized accessor
functions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Generalize SNS generic-services routines.
Consolidate completion-status checking while adding support
for the ISP24xx.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx diagnostic routines.
Add function and structure definitions for the ISP24xx
diagnostic firmware dump routines.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx definitions.
Add requisite structure definitions and #define's for ISP24xx
support. Also drop volatile modifiers from device_reg_* register
layouts as the members are never really accessed, only their
offsets within the layout are used during reads and writes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add pci ids for new ISP types.
Move old definitions in local qla_def.h file to pci_ids.h as
well.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Factor-out ISP specific functions to method-based call tables.
In anticipation of ISP24xx/ISP25xx support, factor-out ISP
specific functions into a method-based call table.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
At the moment, the transport class blindly tries to set things like
QAS and IU, even if the drive won't support them. It's best not to
annoy the devices like this and instead only set what the drive says
is actually supported.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
now that we do normal PCI probing there's no need to keep a list of
all HBAs.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/dpt_i2o.c: In function `adpt_queue':
drivers/scsi/dpt_i2o.c:385: warning: unused variable `timeout'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use the macros consistently in ahd_linux_dev_reset().
If ahd_linux_dev_reset() really can be called with local interrupts disabled
then yuk.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One correction is needed. Changes are not needed for
drivers/scsi/pcmcia/nsp_cs.c because it uses versioning in the
compatibility part, which is never used in 2.6 kernels. The only right
thing we could to that compatibility code would be to remove it throughout
the file, but that would be a separate patch.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Linux PCMCIA code has some data that was apparently used (or meant to be
used) to ensure that only proper client drivers are loaded. This is now
ensured (to a certain degree) by the fact that the most client drivers are
part of the kernel. Also, the version information has not been updated
despite major changes in PCMCIA API. This has made it meaningless.
This patch removes servinfo_t and pcmcia_get_card_services_info. They are not
used in any userspace utilities such as pcmcia-cs and pcmciautils.
drivers/pcmcia/pcmcia_ioctl.c is adjusted accordingly.
CS_RELEASE and CS_RELEASE_CODE are removed. include/pcmcia/version.h is empty
now. It will be removed later, but for now it's left in the tree to avoid
touching all PCMCIA clients.
The only driver that needs to be changed is drivers/scsi/pcmcia/nsp_cs.c,
which uses CS_RELEASE_CODE.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the usage of struct of_match to struct of_device_id,
similar to pci_device_id. This allows a device table to be generated,
which can be parsed by depmod(8) to generate a map file for module
loading.
In order for hotplug to work with macio devices, patches to
module-init-tools and hotplug must be applied. Those patches are
available at:
ftp://ftp.suse.com/pub/people/jeffm/linux/macio-hotplug/
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apparently these are the only drives that try to negotiate IU and QAS
at u160 speeds. The aic7xxx driver can't cope with this. The fix is
to eliminate the IU and QAS setting routines. I've #if 0'd them out,
just in case we ever get the sequencer documentation out of Adaptec,
since we'd then be able to fix the driver.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix the problem in IBM VSCSI Client where the client doesn't send the
information which is expected by the server.
Signed-off-by: Linda Xie <lxie@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update copyright notice text and include year 2005.
Add Copyright notice for Christoph Hellwig to several files: lpfc.h
lpfc_attr.c lpfc_els.c lpfc_hbadisc.c lpfc_init.c lpfc_mbox.c
lpfc_mem.c lpfc_nportdisc.c lpfc_scsi.c lpfc_sli.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Symptom - An unmapped node (initiator) that goes away in a situation
such as cable pull, comes back as a mapped node. Fix - On ADISC
completion, put a list on the mapped list only if it is a FCP_TARGET.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add completion handler to the abort iocbs to close a hole where we
could reuse an iotag.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
lpfc_els_unsol_event() checks rjt_err to determine is LS_RJT should be
sent. However, rjt_err was set to LSEXP_NOTHING_ELSE (which is 0) in
cases where an LS_RJT should be sent, so rjt_err was never true.
Change lpfc_els_unsol_event() to set rjt_err to 1 when LS_RJT should
be sent.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix driver not seeing LP6000. Fix: add PCI id to the pci_device_id
table and a short description for the HBA in get_hba_model_desc().
Also add a default clause to the switch statement that parses the
various PCI ID's.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add max_sectors to the driver host template and initialize it with
0xFFFF since the driver has no limitations on the size a transfer
contained by a scsi command and that fits within the sg_tablesize
provisioned by the driver. This fixes a performance issue seen in
some configurations.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug reported via SourceForge - lpfc does not load on sparc. The lpfc
driver must byteswap all FCP IOCBs to recover the data into cpu native
format.
Also correct issue of "iotag not found" messages
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Analysis:
Timeout of READ_SPARM64 causes call to lpfc_mbox_timeout_handler which
reads psli->mbox_active to determine the timeout mbox. Timeout
handler then NULL's psli->mbox_active and calls
lpfc_mbx_cmpl_read_sparam(), which on timeout condition, calls
link_down(). link_down() now calls disc_done() which calls
mbox_timeout_hander() again since WORKER_MBOX_TMO is still set, which
goes back to read psli->mbox_active which is already NULL'ed.
Remove redundant if statement in lpfc_mbox_timeout_handler. pmbox is
assigned psli->mbox_active so there is no need to check if it actually
equals psli->mbox_active.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix issue where all hosts connected to SAN get spammed with nodev
message when other initiators go away. Display nodev message only
when FC targets go away. However this behavior will be overridden if
LOG_DISCOVERY is set.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Christoph Hellwig <hch@lst.de>:
- rename PGP/HPH to lpfc_pgp/lpfc_hgp
- use __le32 types for the members to start fixing sparse -Wbitwise
issues
- remove lpfc_sli.MBhostaddr, we can always use the pointer from
SLI2_DESC directly
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The check in
627 BUG_ON(index > SG_MEMPOOL_NR);
with SG_MEMPOOL_NR defined in
32 #define SG_MEMPOOL_NR (sizeof(scsi_sg_pools)/sizeof(struct scsi_host_sg_pool))
was not sufficient.
sgp, set in
629 sgp = scsi_sg_pools + index;
is dereferenced in
630 mempool_free(sgl, sgp->pool);
Signed-off-by: Zaur Kambarov <zkambarov@coverity.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now we can change the pci core to always set this pointer, as pci drivers
should use it, not the driver core callback.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch lengthens the delay between DET setting and clearing for
COMMRESET from 400us to 1ms. I couldn't find any requiremen regarding
the duration of COMMRESET in SATA I/II specs but AHCI-1.1 10.4.2
states that it should be at least 1ms.
Signed-off-by: Tejun Heo <htejun@gmail.com>
From: Andy Whitcroft <apw@shadowen.org>
Updated to remove the bogus translated target check.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We never look at it except for the old megaraid driver that abuses it
for sending internal commands. That usage can be fixed easily because
those internal commands are single-threaded by a mutex and we can easily
use a completion there.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
it's never set to anything, and just three broken drivers are looking
at it and doing odd things.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch add the following products to the driver:
IBM ServeRAID 8i
ICP 9014R0
ICP 9024R0
ICP 9047MA
ICP 9087MA
ICP 9085LI
ICP 5085AU
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_add_host is the proper place to set the device, but people copy
the scsi_set_device usage from older drivers again and again.
note that this leaves some legacy drivers like qlogicisp/qlogicfc
without pci association in sysfs, but they're scheduled to go away soon
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use ssleep() instead of schedule_timeout to guarantee the task
delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains the following cleanups:
- make needlessly global code static
- remove or #if 0 the following unused functions:
- tul_pop_pend_scb
- tul_device_reset
- tul_reset_scsi_bus
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another rollup of patches which give various symbols static scope
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver plays with waitqueue internals and fails to compile after Ben's
"aio: make wait_queue ->task ->private" patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The fixes for sparse warnings mixed in with the fixups for
the raw_srb handler resulted in a bug that showed up in the 32 bit
environments when trying to issue calls directly to the physical devices
that are part of the arrays (ioctl scsi passthrough).
Received from Mark Salyzyn at adaptec.
Applied comment from Christoph to remove cpu_to_le32(0)
Applied Mark S fix of missing memcpy.
It applies to the scsi-misc-2.6 git tree.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Drivers need not implement a hook that returns FAILED, and does nothing
else, since the SCSI midlayer code will do that for us.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI ->done() hook should not be called from inside a spinlock.
Drivers that do this are mostly cut-n-paste from 2.2.x-era.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following the go around over the SONY DVD that needs artificial limits,
this should be the correct code for all cases (minus the debugging
prints).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
M68k: Mark Sun-3 NCR5380 SCSI broken until NCR5380_abort() and
NCR5380_bus_reset() are replaced with real new-style EH routines (the old EH
SCSI constants were removed in 2.6.12-rc3).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- the eisa layer only probes when it's actually safe, no need for
a driver option
- store the id table directly in linux format instead of convering
at runtime
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
there's absolutely no reason not to trust the driver private data
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return to previous held-logic of calling scsi_add_host() only
after the board has been completely initialized. Also return
pci_*() error-codes during probe failure paths.
This also corrects an issue where only lun 0 is being scanned for
a given port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Problem:
Incorrect md5sum when using ATAPI PIO mode to verify a distro CD.
Root cause: sg traverse problem.
In __atapi_pio_bytes(), if qc->cursg++ is increased and "goto
next_page" is executed, then sg is not updated to the new qc->cursg
and the old sg is overwritten with the new data.
Changes:
- Replace "goto next_page" with "goto next_sg" to make sg updated.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Bump sata_svw.c version number to indicate support for BCM5785(HT1000)
Southbridge SATA controller.
Signed-off-by: Narendra Sankar <nsankar@broadcom.com>
diff -uNr linux-2.6.12-rc5/drivers/scsi/sata_svw.c linux-2.6.12-rc5.brcm/drivers/scsi/sata_svw.c
This patch adds some files into the /sys/class/scsi_host/hostN
directories for aacraid adapters:
model
vendor
hba_kernel_version
hba_monitor_version
hba_bios_version
serial_number
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are several extra things that have to be considered when running
Domain Validation on a u320 target (notably how you fall back).
Hopefully this should help us when someone adds this transport class to
aic79xx.
I've tested this on the lsi1030, so I know it works correctly up to
u320.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For setting coupled parameters, we need to be comparing against the goal
settings, not the current ones.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A problem exists todayin the sg driver that if an SG_IO request is
outstanding to a device when it is removed from the system. The
system may oops if that command completes later in time.
1. sg_remove gets called
2. sg_remove calls sg_finish_req_req on all pending requests
This removes the Sg_request's from the headrp list in the Sg_fd
3. The sleeping SG_IO ioctl is woken. It does nothing and returns.
4. The caller closes the fd, which invokes sg_release
5. sg_release calls sg_remove_sfp. It finds no outstanding commands
since the headrp list is empty, so it calls __sg_remove_sfp,
which frees the sfp.
6. Now when sg_cmd_done gets called, sg uses upper_private_data in
the Scsi_Request, which should point to the srp, which has been
freed, so it points to freed memory.
7. sg then dereferences the srp pointer to get the sfp, and we oops.
The fix is to NULL out the upper_private_data field in this path,
which sg_cmd_done already checks for, which will prevent the oops
from occurring.
cpu 0x1: Vector: 300 (Data Access) at [c00000000fff7aa0]
pc: d0000000002bbea8: .sg_cmd_done+0x70/0x394 [sg]
lr: d000000000073304: .scsi_finish_command+0x10c/0x130 [scsi_mod]
sp: c00000000fff7d20
msr: 8000000000009032
dar: 2f70726f63202f78
dsisr: 40000000
current = 0xc0000000024589b0
paca = 0xc0000000003da800
pid = 7, comm = events/1
[c00000000fff7dc0] d000000000073304 .scsi_finish_command+0x10c/0x130 [scsi_mod]
[c00000000fff7e50] d00000000007317c .scsi_softirq+0x140/0x168 [scsi_mod]
[c00000000fff7ef0] c0000000000634dc .__do_softirq+0xa0/0x17c
[c00000000fff7f90] c000000000018430 .call_do_softirq+0x14/0x24
[c00000000ed472e0] c0000000000142e0 .do_softirq+0x74/0x9c
[c00000000ed47370] c000000000013c9c .do_IRQ+0xe8/0x100
[c00000000ed473f0] c00000000000ae34 HardwareInterrupt_entry+0x8/0x54
c00000000003df28 .smp_call_function+0
x100/0x1d0
[c00000000ed47780] c0000000000ba99c .invalidate_bh_lrus+0x30/0x70
[c00000000ed47810] c0000000000b91a0 .invalidate_bdev+0x18/0x3c
[c00000000ed478a0] c0000000000da7b8 .__invalidate_device+0x70/0x94
[c00000000ed47930] c0000000001d40bc .invalidate_partition+0x4c/0x7c
[c00000000ed479c0] c00000000010a944 .del_gendisk+0x48/0x15c
[c00000000ed47a50] d00000000003d55c .sd_remove+0x34/0xe4 [sd_mod]
[c00000000ed47ae0] c0000000001c5d30 .device_release_driver+0x90/0xb4
[c00000000ed47b70] c0000000001c6130 .bus_remove_device+0xb0/0x12c
[c00000000ed47c00] c0000000001c4378 .device_del+0x120/0x198
[c00000000ed47ca0] d00000000007dcdc .scsi_remove_device+0xb4/0x194 [scsi_mod]
[c00000000ed47d30] d0000000000a5864 .ipr_worker_thread+0x1d4/0x27c [ipr]
[c00000000ed47dd0] c0000000000734c4 .worker_thread+0x238/0x2f4
[c00000000ed47ee0] c0000000000796c0 .kthread+0xcc/0x11c
[c00000000ed47f90] c000000000018ad0 .kernel_thread+0x4c/0x6c
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
