for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use DEFINE_SPINLOCK instead of initializing spinlocks to
SPIN_LOCK_UNLOCKED, since DEFINE_SPINLOCK is better for lockdep.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just another pass through arch/powerpc for old usages.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable Periodic Recalibration (PTCAL) support for Cell XDR memory,
using the new ibm,cbe-start-ptcal and ibm,cbe-stop-ptcal RTAS calls.
Tested on QS20 and QS21 (by Thomas Huth). It seems that SLOF has
problems disabling, at least on QS20; this patch should only be
used once these problems have been addressed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for a proper device-tree.
A porper device-tree on cell contains be nodes
for each CBE containg nodes for SPEs and all the
other special devices on it.
Ofcourse oldschool devicetree is still supported.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The new PMI driver was added in order to support
cpufreq on blades that require the frequency to
be controlled by the service processor, so use it
on those.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds some attributes the cpu and spu nodes:
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_begin
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_end
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_full_stop
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch introduces a little function for transforming
register values into temperature.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This change fixes the case where spu_base and spufs are initialised on a
system with no SPEs - unconditionally create the spu_lists so spu_alloc
doesn't explode, and check for spu_management ops before starting spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
arch/powerpc/platforms/cell/spu_base.c | 7 ++++---
arch/powerpc/platforms/cell/spufs/inode.c | 5 +++++
2 files changed, 9 insertions(+), 3 deletions(-)
spu_base.c is always built into the kernel image, so there is no need
for a cleanup function. And some of the things it does are in the
way for my following patches, so I'd rather get rid of it ASAP.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
- remove the spu_acquire_runnable from spu_run_init. I need to
opencode it in spufs_run_spu in the next patch
- remove various inline attributes, we don't really want to inline
long functions with multiple callsites
- cleanup return values and runcntl_write calls in spu_run_init
- use normal kernel codingstyle in spu_reacquire_runnable
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spu_coredump_calls.owner is NULL in case of a builtin spufs,
so the checks in here break.
Check for the availability of the spu_coredump_calls variable
instead.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Dynamically allocated read/write buffer in spufs_arch_write_note() will
not be freed. Convert it to get_free_page at the same time.
Cc: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Change the loop in spu_wait to be a little more straightforward.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Add a 'mode=' option to spufs mount arguments. This allows more
control over access to the top-level spufs directory.
Tested on Cell.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
GCC may generates inline copy loop to handle memcpy() function
instead of kernel defined memcpy(). But this inlined version of memcpy()
causes an alignment interrupt when copying from local store.
This patch uses memcpy_fromio() and memcpy_toio to copy local store
to prevent memcpy() being inlined.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
We now have proper locking around assignets of the mapping pointers,
and the spin_unlock implies enough of a barrier to get rid of the
explicit one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
When SPU isolation mode enabled, isolated_loader would be
allocated by spufs_init_isolated_loader() on module_init().
But anyone do not free it.
This patch introduces spufs_exit_isolated_loader() which is
the opposite of spufs_init_isolated_loader() and called on
module_exit().
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spufs module_init forgot to call a few cleanup functions
on error path. This patch also includes cosmetic changes in
spu_sched_init() (identation fix and return error code).
[modified by hch to apply ontop of the latest schedule changes]
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch checks return value of spu_acquire_runnable() in
spufs_mfc_write().
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
There is no reason for run_sema to be a struct semaphore. Changing
it to a mutex and rename it accordingly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This change populates a siginfo struct for SPE application exceptions
(ie, invalid DMAs and illegal instructions).
Tested on an IBM Cell Blade.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Until now, we have always entered the spu page fault handler
with a mutex for the spu context held. This has multiple
bad side-effects:
- it becomes impossible to suspend the context during
page faults
- if an spu program attempts to access its own mmio
areas through DMA, we get an immediate livelock when
the nopage function tries to acquire the same mutex
This patch makes the page fault logic operate on a
struct spu_context instead of a struct spu, and moves it
from spu_base.c to a new file fault.c inside of spufs.
We now also need to copy the dar and dsisr contents
of the last fault into the saved context to have it
accessible in case we schedule out the context before
activating the page fault handler.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
There is no reason to execute spu_init_channels under spu_mutex
after the spu has been taken off the freelist it's ours.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Addition to stop_wq needs to happen before adding to the runqeueue and
under the same lock so that we don't have a race window for a lost
wake up in the spu scheduler.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
For quite a while now spu state is protected by a simple mutex instead
of the old rw_semaphore, and this means we can simplify the locking
around spu_setup_isolated a lot.
Instead of doing an spu_release before entering spu_setup_isolated and
then calling the complicated spu_acquire_exclusive we can now simply
enter the function locked an in guaranteed runnable state, so that the
only bit of spu_acquire_exclusive that's left is the call to
spu_unmap_mappings.
Similarly there's no more need to unlock and reacquire the state_mutex
when spu_setup_isolated is done, but we can always return with the
lock held and only drop it in spu_run_init in the failure case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
A single context should only be woken once, and we should not have
more wakeups for a given priority than the number of contexts on
that runqueue position.
Also add some asserts to trap future problems in this area more
easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
set_bit does not guarantee ordering on powerpc, so using it
for communication between threads requires explicit
mb() calls.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
To not lose a spu thread we need to make sure it always gets put back
on the runqueue. In find_victim aswell as in the scheduler tick as done
in the previous patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
To not lose a spu thread we need to make sure it always gets put back
on the runqueue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Make sure the pointers to various mappings are cleared once the last
user stopped using them. This avoids accessing freed memory when
tearing down the gang directory aswell as optimizing away
pte invalidations if no one uses these.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The scheduler workqueue may rearm itself and deadlock when we try to stop
it. Put a flag in place to avoid skip the work if we're tearing down
the context.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This also fixes a bug where a property value was being modified
in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no reason to yield the CPU in spu_yield - if the backing
thread reenters spu_run it gets added to the end of the runqueue for
it's priority. So the yield is just a slowdown for the case where
we have higher priority contexts waiting.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I wanted to enable CBE_THERM on PS3. So I had to enable CBE_RAS first.
But the resulting kernel doesn't link, as cbe_regs.c isn't compiled for
non-PPC_CELL_NATIVE.
CBE_RAS should depend on PPC_CELL_NATIVE; this makes it so.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPU code doesn't properly invalidate SPUs SLBs when necessary,
for example when changing a segment size from the hugetlbfs code. In
addition, it saves and restores the SLB content on context switches
which makes it harder to properly handle those invalidations.
This patch removes the saving & restoring for now, something more
efficient might be found later on. It also adds a spu_flush_all_slbs(mm)
that can be used by the core mm code to flush the SLBs of all SPEs that
are running a given mm at the time of the flush.
In order to do that, it adds a spinlock to the list of all SPEs and move
some bits & pieces from spufs to spu_base.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Due to a buggy unsigned comparison, it was possible to write
beyond the end of the local store file in spufs under some
circumstances.
This rewrites the buggy function to look more like
simple_copy_from_buffer.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
This will allow us to build without PCI easier.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a clean up patch that includes the following changes:
-Some comments were added to clarify the code based on feedback
from the community.
-The write_pm_cntrl() and set_count_mode() were passed a
structure element from a global variable. The argument was
removed so the functions now just operate on the global directly.
-The set_pm_event() function call in the cell_virtual_cntr()
routine was moved to a for-loop before the for_each_cpu loop
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
I found an exploit in current kernel.
Currently, there is no range check about mmapping "/mem" node in
spufs. Thus, an application can access privilege memory region.
In case this kernel already worked on a public server, I send this
information only here.
If there are such servers in somewhere, please replace it, ASAP.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
For SCHED_RR tasks we can do some really trivial timeslicing. Basically
we fire up a time for every scheduler tick that searches for a higher
or same priority thread that is on the runqueue and if there is one
context switches to it. Because we can't lock spus from timer context
we actually run this from a delayed runqueue instead of a timer.
A nice optimization would be to skip the actual priority bitmap search
when there are less contexts than physical spus available. To implement
this I need a so far unpublished patch from Andre, and it will be added
after we have that patch in.
Note that right now we only do the time slicing for SCHED_RR tasks.
The code would work for SCHED_OTHER tasks aswell, but their prio
value is defered from the one the PPU thread has at time of spu_run,
and using this for spu scheduling decisions would make the code very
unfair. SCHED_OTHER support will be enabled once we the spu scheduler
knows how to calculcate cpu_context.prio (very soon)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
