There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It makes no sense to check for BSY bit being set as earlier OK_STAT()
check in cdrom_end_request() makes sure that BSY bit is cleared.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_end_rq() also for failed non-fs requests on completion
of REQUEST SENSE requests + use blk_rq_bytes() while at it.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use PageHighMem() instead of ifdefs in ide_pio_bytes()
(=> local IRQs won't be disabled when not necessary).
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add support for arbitrary transfer lengths to ide_pio_bytes()
and then inline ide_pio_multi() into ide_pio_datablock().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently¹, some ATAPI devices want to see the packet command first
before enabling DMA otherwise they simply hang indefinitely. Reorder the
two steps and start DMA only after having issued the command first.
[1] http://marc.info/?l=linux-kernel&m=123835520317235&w=2
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Reported-by: Michael Roth <mroth@nessie.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix some incorrect IDE_FTFLAG_* changes which slipped in commit
"ide: add "flagged" taskfile flags to struct ide_taskfile (v2)"
(commit 19710d25d5) few days ago.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On m68k:
| drivers/ide/ide-atapi.c: In function 'ide_io_buffers':
| drivers/ide/ide-atapi.c:87: error: implicit declaration of function 'sg_page'
| drivers/ide/ide-atapi.c:87: warning: passing argument 1 of 'PageHighMem' makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:91: warning: passing argument 1 of 'kmap_atomic' makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:96: error: implicit declaration of function 'sg_virt'
| drivers/ide/ide-atapi.c:96: warning: assignment makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:107: error: implicit declaration of function 'sg_next'
| drivers/ide/ide-atapi.c:107: warning: assignment makes pointer from integer without a cast
[bart: Dmitri Vorobiev submitted similar patch fixing MIPS]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Unfortunately, I missed a catch when reviewing the patch committed as
201bffa4. Here is the fix to the currently broken handling of sleeping
devices. In particular, this is required to get the disk shock
protection code working again.
Reported-by: Christian Thaeter <ct@pipapo.org>
Cc: stable@kernel.org
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass number of bytes instead of sectors to ide_init_sg_cmd().
* Pass number of bytes to process to ide_pio_sector() and rename
it to ide_pio_bytes().
* Rename ->nsect field to ->nbytes in struct ide_cmd and use
->nbytes, ->nleft and ->cursg_ofs to keep track of number of
bytes instead of sectors.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass command structure to ide_execute_command() and skip
__ide_set_handler() for ATAPI protocols on non-DRQ devices.
* Convert ide_issue_pc() to always use ide_execute_command()
and remove no longer needed ide_execute_pkt_cmd().
v2:
* Fix for non-DRQ devices (based on report from Borislav).
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename dma_timer_expiry() to ide_dma_sff_timer_expiry() and export it.
* Add ->dma_timer_expiry method and use it to set hwif->expiry for
ATA_PROT_DMA protocol in do_rw_taskfile().
* Initialize ->dma_timer_expiry to ide_dma_sff_timer_expiry() for SFF hosts.
* Move setting hwif->expiry from ide_execute_command() to its users and drop
'expiry' argument.
* Use ide_execute_command() instead of ->dma_exec_cmd in do_rw_taskfile().
* Remove ->dma_exec_cmd method and its implementations.
* Unexport ide_execute_command() and ide_dma_intr().
v2:
* Fix CONFIG_BLK_DEV_IDEDMA=n build (noticed by Randy Dunlap).
* Fix *dma_expiry naming (suggested by Sergei Shtylyov).
There should be no functional changes caused by this patch.
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set hwif->expiry prior to calling [__]ide_set_handler()
and drop 'expiry' argument.
* Set hwif->expiry to NULL in ide_{timer_expiry,intr}()
and remove 'hwif->expiry = NULL' assignments.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass command to ide_issue_pc() and update ->do_request methods
in ide-{cd,floppy,tape}.c accordingly.
* Convert ide_pktcmd_tf_load() to ide_init_packet_cmd() which
just initializes command structure and use do_rw_taskfile()
to load ATA_CMD_PACKET commands.
While at it:
* Rename ide{floppy,tape}_issue_pc() to ide_{floppy,tape}_issue_pc().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set IDE_TFLAG_WRITE flag and ->rq also for ATA_CMD_PACKET
commands.
* Pass command to ->dma_setup method and update all its
implementations accordingly.
* Pass command instead of request to ide_build_sglist(),
*_build_dmatable() and ide_map_sg().
While at it:
* Fix scc_dma_setup() documentation + use ATA_DMA_WR define.
* Rename sgiioc4_build_dma_table() to sgiioc4_build_dmatable(),
change return value type to 'int' and drop unused 'ddir'
argument.
* Do some minor cleanups in [tx4939]ide_dma_setup().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_rq_bytes() helper.
* Add blk_noretry_request() quirk to ide_complete_rq() (currently only fs
requests can be marked as "noretry" so there is no change in behavior).
* Switch current ide_end_request() users to use ide_complete_rq().
[ No need to check for rq->nr_sectors == 0 in {ide_dma,task_pio}_intr(),
nsectors == 0 in cdrom_end_request() and err == 0 in ide_do_devset(). ]
* Remove no longer needed ide_end_request().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This results in PIO->DMA retry being triggered also on completion
of requests using ide_complete_rq() instead of ide_end_request().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is no longer needed so remove it, also while at it dequeue the request
only on blk_end_request() success and make ide_complete_rq() return an error
value.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move rq->errors quirk out from ide_end_request() to its call sites.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set rq->errors at ide_complete_rq() call sites and then pass
error value to ide_complete_rq().
[ Some rq->errors assignments look really wrong but this patch
leaves them alone to not introduce too many changes at once. ]
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move 'uptodate' quirk from ide_end_rq() to its users.
* Move quirks for blk_noretry_request() and !blk_fs_request()
requests from ide_end_rq() to ide_end_request().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move request dequeuing from __ide_end_request() to ide_end_request().
* Rename __ide_end_request() to ide_end_rq() and export it.
* Fix ide_end_rq() to pass original blk_end_request() return value.
* ide_end_dequeued_request() is used only in cdrom_end_request()
so inline it there and then remove the function.
v2:
* Remove needless BUG_ON() while at it (start_request()'s one is enough).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_end_request() call out from ide_finish_cmd() to its users.
* Use ide_finish_cmd() in task_no_data_intr().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fixup ->tf_flags in ide_do_park_unpark() to match their current use.
* Use ide_complete_cmd() for REQ_UNPARK_HEADS.
While at it:
* No need to read Error register for PM requests in task_no_data_intr().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move handling of head unload commands from task_no_data_intr()
to ide_complete_cmd() and then use ide_complete_cmd() also for
head unload commands.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_error() call from task_error() to task_pio_intr()
(the only user).
* Drop no longer used arguments from task_error().
* Rename task_error() to ide_error_cmd().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
task_in_unexpected() is only used by task_pio_intr() so inline it there.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge task_out_intr() with task_in_intr().
* Rename task_in_intr() to task_pio_intr().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_MULTI_PIO taskfile flag and set it for commands
using multi-PIO protocol.
* Use ata_tf_protocols enums instead of TASKFILE_* defines to
denote command's protocol and then rename ->data_phase field
to ->protocol.
* Remove no longer needed <linux/hdreg.h> includes.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also take care of fixing up incorrect TASKFILE_IN_DMA[Q] data phase when
IDE_DRIVE_TASK_RAW_WRITE is requested (no need to do it for TASKFILE_NO_DATA
and TASKFILE_[MULTI]_IN -- it had no chance of working previously).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move command related fields from ide_hwif_t to struct ide_cmd.
* Make ide_init_sg_cmd() take command and sectors number as arguments.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_FS taskfile flag and set it for REQ_TYPE_FS requests.
* Convert ->{in,out}put_data methods to take command instead of request
as an argument. Then convert pre_task_out_intr(), task_end_request(),
task_error(), task_in_unexpected(), ide_pio_sector(), ide_pio_multi()
and ide_pio_datablock() in similar way.
* Rename task_end_request() to ide_finish_cmd().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- rename struct ide_task_s to struct ide_cmd
- remove stale comments from idedisk_{read_native,set}_max_address()
- drop unused 'cmd' argument from ide_{cmd,task}_ioctl()
- drop unused 'task' argument from tx4939ide_tf_load_fixup()
- rename ide_complete_task() to ide_complete_cmd()
- use consistent naming for struct ide_cmd variables
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Re-map sg table if needed in ide_build_sglist().
* Move ide_build_sglist() call from ->dma_setup to its users.
* Un-export ide_build_sglist().
v2:
* Build fix for CONFIG_BLK_DEV_IDEDMA=n (noticed by Randy Dunlap).
There should be no functional changes caused by this patch.
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use blk_fs_request() in ide-taskfile.c instead of checking for:
- rq->bio in ide_pio_datablock() and task_error()
- rq->cmd_type == REQ_TYPE_ATA_TASKFILE in task_end_request()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make ->pc_callback method return request status and then move
the request completion from ->pc_callback to ide_pc_intr().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Handle completion of private driver requests explicitly
for ide_floppy and ide_tape media in ide_kill_rq().
* Remove no longer needed ->end_request method.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide*_end_request() is only called with uptodate == 0 or uptodate == 1
so cleanup it accordingly.
* Inline ide*_end_request() content at call sites so the only user left
is ->end_request method.
* ->end_request is now used only for private driver requests so remove
handling of other requests from ide*_end_request().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move IDE{FLOPPY,TAPE}_ERROR_* defines to <linux/ide.h> and rename them
to IDE_DRV_ERROR_*.
* Handle ->end_request special cases for floppy/tape media in ide_kill_rq().
* Call ->end_request only for private device driver requests.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ->failed_pc from struct ide_{disk,tape}_obj to ide_drive_t.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
No need to check / clear hwif->sg_nents.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Re-map sg table if necessary (not that it really matters since
DMA support is disabled currently).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move smart_enable() call out from get_smart_data() to
proc_idedisk_read_smart().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always use hwif->task->data_phase and remove ->data_phase
field from ide_hwif_t.
* Remove superfluous REQ_TYPE_ATA_TASKFILE check from
ide_pio_datablock() while at it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move request type specific code from ide_end_drive_cmd() to callers.
* Remove stale ide_end_drive_cmd() documentation and drop no longer
used 'stat' argument. Then rename the function to ide_complete_rq().
v2:
* Fix handling of blk_pm_request() requests in task_no_data_intr().
v3:
* Some ide_no_data_taskfile() users (HPA code and HDIO_DRIVE_* ioctls
handlers) access original command later so we need to update it in
ide_complete_task().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out completion of taskfile from ide_end_drive_cmd()
to ide_complete_task().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Complete power step in ide_complete_pm_request().
* Rename ide_complete_pm_request() to ide_complete_pm_rq().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->ftf_flags field to struct ide_taskfile
and convert flags for TASKFILE ioctl to use it.
* Rename "flagged" taskfile flags:
- IDE_TFLAG_FLAGGED -> IDE_FTFLAG_FLAGGED
- IDE_TFLAG_FLAGGED_SET_IN_FLAGS -> IDE_FTFLAG_SET_IN_FLAGS
- IDE_TFLAG_{OUT,IN}_DATA -> IDE_FTFLAG_{OUT,IN}_DATA
v2:
* Remember to fully update ide-h8300.c, scc_pata.c and tx493{8,9}ide.c
(thanks to Stephen Rothwell for noticing).
There should be no functional changes caused by this patch.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_4DRIVES host flag and use it instead of ide_4drives
chipset type in ide_init_port().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_DTC2278 host flag and use it instead of ide_dtc2278
chipset type in ide_init_port().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->irq_flags field to struct ide_port_info and struct ide_host.
* Update host drivers and IDE PCI code to use ->irq_flags field.
* Convert init_irq() and ide_intr() to use host->irq_flags.
This fixes handling of shared IRQs for non-PCI hosts
and removes ugly ifdeffery from core IDE code.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always free drive->id in probe_for_drive() if device is not present.
While at it:
- remove dead IDE_DFLAG_DEAD flag
- remove superfluous IDE_DFLAG_PRESENT check
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Suggested-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: minor CodingStyle fixup per Sergei's suggestion]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove superfluous <asm/macints.h> include.
* No need to re-define in/out*() macros as they are no longer used
by m68k host drivers.
* readl() and writel() are not used by core IDE code.
* Use raw_*_swapw() directly in {falcon,q40}ide.c and remove
{in,out}sw_swapw() macros.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->{get,release}_lock methods to struct ide_port_info
and struct ide_host.
* Convert core IDE code, m68k IDE code and falconide support to use
->{get,release}_lock methods instead of ide_{get,release}_lock().
* Remove IDE_ARCH_LOCK.
v2:
* Build fix from Geert updating ide_{get,release}_lock() callers in
falconide.c.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This micro-optimization is not worth it. Just always check for
existence of ->ack_intr method in ide_intr() and ide_timer_expiry().
v2:
Fix brown-paper-bag bug spotted by David D. Kilzer.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Cc: "David D. Kilzer" <ddkilzer@kilzer.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
and more specifically, push __func__ into debug
macro thus making ide_debug_log() calls shorter and more readable.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
This fixes hwif->channel and drive->dn assignments.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This fixes hwif->channel and drive->dn assignments.
v2:
Fix v5/v6 mismatch noticed by Russell.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Pass pointer to buffer for IDENTIFY data to do_identify()
and try_to_identify().
* Un-static try_to_identify() and use it in ide_driveid_update().
* Rename try_to_identify() to ide_dev_read_id().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Clear drive IRQ after re-enabling local IRQs in ide_driveid_update()
to match try_to_identify().
Also remove superfluous local_irq_enable() call while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Defer classifying device type from do_identify() to do_probe().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
do_identify() marks EXABYTENEST device as non-present and frees
drive->id so enable_nest() has absolutely no chance of working.
The code was like this since at least 2.6.12-rc2 and nobody
has noticed so just remove broken EXABYTENEST support.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Doing kmalloc() in the middle of command execution is not only ugly
but leaves drive waiting to send data on kmalloc() failure. Fix it.
While at it:
* Unify error code paths.
* Fixup error message to be more useful and add missing KERN_ERR level.
* Rename 'stat' variable to 's'.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set ->irq explicitly in cs5520.c.
* Remove irq argument from ide_hw_configure().
* Remove pciirq argument from ide_pci_setup_ports().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return 0 instead of dev->irq in ->init_chipset implementations.
* Fix ->init_chipset method to return 'int' value instead of
'unsigned int' one.
This fixes ->init_chipset handling for host drivers (cs5530, hpt366
and pdc202xx_new) for which it is possible for this method to fail.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is now handled by core IDE PCI code.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move handling of IDE_HFLAG[_FORCE]_LEGACY_IRQS from ide_init_port()
to ide_pci_init_{one,two}().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Core IDE PCI code takes care of assigning hwif->irq for both ports.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Core IDE PCI code takes care of assigning hwif->irq for both ports.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix ->init_hwif to check if IDE PCI controller is in compatibility
mode instead of checking for hwif->irq == 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do some CodingStyle fixups in <linux/ide.h> while at it.
v2:
Add missing <linux/delay.h> include (reported by Stephen Rothwell).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix following checkpatch.pl warnings/errors:
- WARNING: space prohibited between function name and open parenthesis '('
- WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
- WARNING: line over 80 characters
- ERROR: trailing whitespace
- ERROR: space required before the open parenthesis '('
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move xfer mode tuning code to ide-xfer-mode.c.
* Add CONFIG_IDE_XFER_MODE config option to be selected by host drivers
that support xfer mode tuning.
* Add CONFIG_IDE_XFER_MODE=n static inline versions of ide_set_pio()
and ide_set_xfer_rate().
* Make IDE_TIMINGS and BLK_DEV_IDEDMA config options select IDE_XFER_MODE,
also add explicit selects for few host drivers that need it.
* Build/link ide-xfer-mode.o and ide-pio-blacklist.o (it is needed only
by ide-xfer-mode.o) only if CONFIG_IDE_XFER_MODE=y.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out processing of special commands from ide_special_rq()
to ide_do_devset() and ide_do_park_unpark().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use elv_add_request() instead of __elv_add_request() in ide_do_drive_cmd().
* ide_do_drive_cmd() is used only in ide-{atapi,cd}.c so inline it there.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_dma_timeout_retry() to ide-dma.c and add static inline
version for CONFIG_BLK_DEV_IDEDMA=n.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move drive_is_ready() to ide-io.c, then make it static.
Also make some minor CodingStyle fixups while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* taskfile_load_raw() is used only by do_drive_set_taskfiles()
so inline it there.
While at it:
- rename 'args' variable to 'task'
- remove struct taskfile_array
- do ide_acpigtf check early
- use REGS_PER_GTF
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_noacpi is already checked by ide_acpi_exec_tfs()
which is the only user of do_drive_set_taskfiles().
* ide_acpi_exec_tfs() prints sufficient debug info about the
device so no need to do it again.
* do_drive_get_GTF() + ide_acpi_exec_tfs() make sure that this
function will never be called with incorrect gtf_length argument
or if device is not present.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_noacpi is already checked by ide_acpi_exec_tfs()
which is the only user of do_drive_get_GTF().
* ide_acpi_exec_tfs() prints sufficient debug info about the
device so no need to have excessive data about port/host.
* It is sufficient to check for drive->acpidata->obj_handle
as it will be NULL if dev == NULL or hwif->acpidata == NULL
or device is not present.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_acpi_init() -> ide_acpi_init_port()
* ide_acpi_blacklist() -> ide_acpi_init()
* Call ide_acpi_init() only once (do it during IDE core
initialization) and cleanup the function accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_for_each_present_dev() iterator and convert IDE code to use it.
* Do some drive-by CodingStyle fixups in ide-acpi.c while at it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Init ACPI handles for devices in ide_acpi_port_init_devices()
and remove no longer needed ide_acpi_drive_get_handle().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Then make it static and remove 'dma' argument.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* IDE_DFLAG_NO_IO_32BIT may be set by cmd640's ->init_dev method
so don't clear it in ide_port_tune_devices() (+ no need to do it).
* Move IDE_DFLAG_NO_IO_32BIT handling to ide_port_init_devices().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
dma_map_sg could return a value different to 'nents' argument of
dma_map_sg so the ide stack needs to save it for the later usage
(e.g. for_each_sg).
The ide stack also needs to save the original sg_nents value for
pci_unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
since it fails the virt_to_page() translation check with DEBUG_VIRTUAL
enabled.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory
Controller with Compact Flash True IDE Mode logic.
Driver have to switch 8/16 bit bus width when accessing Task Tile or Data
Register. Moreover some extra things need to be done when setting PIO mode.
Only PIO mode is used, hardware have no DMA support. If interrupt line is
connected through GPIO extra quirk is needed to cope with fake interrupts.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Commit 9567b349f7 (ide: merge ->atapi_*put_bytes
and ->ata_*put_data methods) introduced a regression WRT the odd-length ATAPI
PIO transfers -- the final word didn't get written (causing command timeouts).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix this sparse warnings:
drivers/ide/ide-disk_proc.c:130:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-floppy_proc.c:32:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-proc.c:234:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-tape.c:2141:11: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Cc: trivial@kernel.org
Cc: kernel-janitors@vger.kernel.org
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
bart:
It seems like the bug could cause insanely long timeouts for:
- ATA_DMA_ERR error in dma_timer_expiry()
- commands without ->expiry in tc86c001_timer_expiry()
(TC86C001 IDE controller only)
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: port it to the current tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
During host driver module removal del_gendisk() results in a final
put on drive->gendev and freeing the drive by drive_release_dev().
Convert device drivers from using struct kref to use struct device
so device driver's object holds reference on ->gendev and prevents
drive from prematurely going away.
Also fix ->remove methods to not erroneously drop reference on a
host driver by using only put_device() instead of ide*_put().
Reported-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just copy the comment from drivers/scsi/sr.c::sr_done()
(from which the capacity hack has been originated).
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix missing parentheses so PIO/DMA timings for master device on the
second channel are programmed correctly (IOW "8 0 24 16" offset values
should be used instead of the current "8 0 16 16").
[ The bug went unnoticed because after PIO/DMA timings get programmed
incorrectly for the third device they are overwritten with timings
for the fourth device and since BIOS should also program timings for
the third device everything should work fine until suspend/resume
cycle or user requested transfer mode changes. ]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Documentation/kernel-parameters.txt
- ide=nodma is no longer valid.
drivers/ide/Kconfig
- The module is ide-core.ko not ide.
drivers/ide/ide.c
- It took me a while to figure out what the arguments %d.%d:%d to nodma
module parameter ment, so I added a comment to each.
- Added a comment to each of the sscanf lines.
- There is a bug, if j is 0 it would previously clear all the other bits
except the current device, changed in three different places.
mask &= (1 << i) should be mask &= ~(1 << i).
Signed-off-by: David Fries <david@fries.net>
[bart: s/disk/device/ in ide.c, beautify patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The @fnac.net will be shut down within a couple of months, so fix my
email address.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to pass struct ide_port_info also to ide_host_register().
v2:
Fix v5/v6 mismatch noticed by Russell.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The bcount is greater than 0 and less than or equal to 0x10000.
Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.
Changes done while at it:
* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
(chipset uses shared PIO/MWDMA timings).
* Fix cable detection to report 80-wires cable if BIOS set it for any
device on a port (IDE core will do drive-side cable detection later).
* Don't disable UDMA while programming PIO timings.
* Simplify PCI/MSR support.
Pros of having IDE host driver in addition to libata's one:
* IDE is much lighter than SCSI+libata, the host driver itself is also
a bit smaller:
text data bss dec hex filename
1261 496 4 1761 6e1 drivers/ata/pata_cs5536.o
1242 128 4 1374 55e drivers/ide/cs5536.o
* This allows use of IDE features which are unavailable under libata.
v2:
* Fixes per review from Sergei:
- simplify dependency check in Kconfig
- use IDE_DRV_MASK also for ->drive_data
- disable UDMA when programming MWDMA
- program new DTC timings only when necessary
- fix printk() level in cs5536_init_one()
* Fix patch description according to comments from Alan and Sergei.
v3:
* Smarter masking of UDMA bits per Sergei's suggestion.
Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the
Pegasos).
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On reboot the loop in device_shutdown gets confused by these partially
initialized devices and goes into an infinite loop. Therefore unregister
and disable these devices.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[bart: remove leftover hwif->present clearing + update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out port freeing from ide_host_free() to ide_free_port().
* Add ide_disable_port() and use it on ide_register_port() failure.
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC drivers/ide/palm_bk3710.o
drivers/ide/palm_bk3710.c: In function 'palm_bk3710_probe':
drivers/ide/palm_bk3710.c:382: warning: assignment makes integer from pointer without a cast
Someone should fix hw_regs_t to neither be a typedef, nor
use "unsigned long" where it should use "void __iomem *".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[m68k] Falcon IDE: always serialize, in order to force execution of
ide_get_lock() and friends.
Signed-off-By: Michael Schmitz <schmitz@debian.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
[bart: set flag in falconide_port_info instead of falconide_init()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Monday 12 January 2009, Simon Holm Thøgersen wrote:
> commit 295f000 ("ide: don't execute the next queued command from the
> hard-IRQ context (v2)") breaks suspend to disk for me. On
> 'echo disk > /sys/power/state' the systems hangs, letting me switch
> virtual consoles, but not responding to Alt+SysRq
Restart the request queue early for REQ_TYPE_PM_RESUME requests
(though there is only one resume request for the whole resume
sequence it stays in the queue until is fully completed and now
depends on kblockd for processing consequential resume states).
Reported-and-bisected-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Tested-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CONFIG_LOPEC and CONFIG_SANDPOINT config options are gone.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some rotating disks also present themselves as CFA devices.
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Vortex86SX with IDE controller revision 0x11 ultra DMA must be
disabled. This patch was tested by DMP and seems to work.
It is a cleaned up version of their older Kernel patch:
http://www.dmp.com.tw/tech/vortex86sx/patch-2.6.24-DMP.gz
Tested-by: Shawn Lin <shawn@dmp.com.tw>
Signed-off-by: Brandon Philips <bphilips@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 54cc1428cf ("ide: remove
local_irq_set() macro") accidentally replaced local_save_flags()
by local_irq_set() in ide_probe_port() and __ide_wait_stat()
which resulted in LOCKDEP breakage.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make consistent use of scc_dma_sff_read_status() throughout the driver.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out ide_dma_sff_write_status(), symmetric to ide_dma_sff_read_status().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move apparently misplaced read_sff_dma_status() method from 'struct ide_tp_ops'
to 'struct ide_dma_ops', renaming it to dma_sff_read_status() and making only
required for SFF-8038i compatible IDE controller drivers (greatly cutting down
the number of initializers) as its only user (outside ide-dma-sff.c and such
drivers) appears to be ide_pci_check_simplex() which is only called for such
controllers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace setting of 'hwif->dma_ops' in the 'alim15x3' and 'palm_bk3710' drivers'
init_dma() methods with initializing the corresponding member of their 'struct
ide_port_info' instances and remove such setting from the 'hpt366' driver that
just doesn't use 'sff_dma_ops'. Along with some code save, this prepares us for
the next patch...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Support for the IT8172 IDE controller was removed from the kernel
sometime after 2.6.18. Support for the only boards that used the IT8172
was removed from the kernel after 2.6.18, as they had never compiled
since 2.6.0. However, there are a couple of platforms that use this
chip: the PMC-Sierra Xiao Hu thin-client computer, which is no longer
in production, and the Linksys NSS4000 Network Attached Storage box,
which is based on the Xiao Hu board. I am attempting to add support
for the Xiao Hu to the kernel, and this IT8172 IDE controller is the
first bit of code in this effort.
This patch resurrects the IT8172 IDE controller code. I began with
the 2.6.18 version of the it8172.c file, and have moved it forward so
that it works with the latest version of the kernel. I have run this
driver on a PMC-Sierra Xiao Hu board with the 2.6.28 kernel, and
I have had no problems with it in my configuration. The attached patch
applies cleanly against 2.6.28.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: alan@lxorguk.ukuu.org.uk
[bart: s/HWIF(drive)/drive->hwif/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This makes ide_port_scan()'s behavior match ide_host_register()'s
one and fixes OOPS in elv_may_queue() during port re-scan.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->cur_dev should now be always valid if ->handler is set so
remove redundant checks from ide_intr() and ide_timer_expiry().
* Apply CodingStyle fixups in ide_timer_expiry() while at it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->handler is set while it shouldn't be it indicates deep problems
so BUG_ON()-ning and preventing further damage is much more appropriate
than merely printing an error message.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... and remove no longer needed cdrom_start_packet_command and
cdrom_transfer_packet_command.
Tested lightly with ide-cd and ide-floppy.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
as it is done for all other IDE ATAPI devices.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... instead of assuming it is set for accelerated DRQ type devices.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According the documentation, id[ATA_ID_DWORD_IO] is non-zero if
the drive supports dword IO, while the code disables support by
setting IDE_DFLAG_NO_IO_32BIT. In addition, this word has been
reused by the ATA8 specification. This patch fixes both cases.
Signed-off-by: Mario Schwalbe <schwalbe@inf.tu-dresden.de>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove id[ATA_ID_DWORD_IO] check altogether per Sergei's suggestion]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_port_for_each_dev() / ide_host_for_each_port() iterators
and update IDE code to use them.
While at it:
- s/unit/i/ variable in ide_port_wait_ready(), ide_probe_port(),
ide_port_tune_devices(), ide_port_init_devices_data(), do_reset1(),
ide_acpi_set_state() and scc_dma_end()
- s/d/i/ variable in ide_proc_port_register_devices()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Allocate device structures dynamically instead of having them embedded
in ide_hwif_t:
* Remove needless zeroing of port structure from ide_init_port_data().
* Add ide_hwif_t.devices[MAX_DRIVES] (table of pointers to the devices).
* Add ide_port_{alloc,free}_devices() helpers and use them respectively
in ide_{host,free}_alloc().
* Convert all users of ->drives[] to use ->devices[] instead.
While at it:
* Use drive->dn for the slave device check in scc_pata.c.
As a nice side-effect this patch cuts ~1kB (x86-32) from the resulting
code size:
text data bss dec hex filename
53963 1244 237 55444 d894 drivers/ide/ide-core.o.before
52981 1244 237 54462 d4be drivers/ide/ide-core.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Because presence of the peer device was not checked in
it821x_set_pio_mode() PIO0 mode was used for taskfile PIO
in single device configurations.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove (now superfluous) ->error method from struct ide_driver.
* Unexport __ide_error() and make it static.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- s/struct ide_driver_s/struct ide_driver/
- use to_ide_driver() macro in ide-proc.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just use u8 instead, also s/__u8/u8/ in ide-cd.h while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move IDE_DEFAULT_MAX_FAILURES to <linux/ide.h>.
* Move ide_cfg_mtx, ide_hwif_to_major[], ide_port_init_devices_data(),
ide_init_port_data(), ide_init_port_hw() and ide_unregister() to
ide-probe.c from ide.c.
* Make ide_unregister(), ide_init_port_data(), ide_init_port_hw()
and ide_cfg_mtx static.
While at it:
* Remove stale ide_init_port_data() documentation and ide_lock extern.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->host_busy field to struct ide_host and use it's first bit
together with lock bitops to provide new ports serialization method.
* Convert core IDE code to use new ide_[un]lock_host() helpers.
This removes the need for taking hwgroup->lock if host is already
busy on serialized hosts and makes it possible to merge ide_hwgroup_t
into ide_hwif_t (done in the later patch).
* Remove no longer needed ide_hwgroup_t.busy and ide_[un]lock_hwgroup().
* Update do_ide_request() documentation.
v2:
* ide_release_lock() should be called inside IDE_HFLAG_SERIALIZE check.
* Add ide_hwif_t.busy flag and ide_[un]lock_port() for serializing
devices on a port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'int port_count' field to ide_hwgroup_t to keep the track
of the number of ports in the hwgroup. Then update init_irq()
and ide_remove_port_from_hwgroup() to use it.
* Remove no longer needed hwgroup->hwif, {drive,hwif}->next,
ide_add_drive_to_hwgroup() and ide_remove_drive_from_hwgroup()
(hwgroup->drive now only denotes the currently active device
in the hwgroup).
* Update locking documentation in <linux/ide.h>.
While at it:
* Rename ->drive field in ide_hwgroup_t to ->cur_dev.
* Use __func__ in ide_timer_expiry().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use hwif instead of hwgroup as {request,free}_irq()'s cookie,
teach ide_intr() to return early for non-active serialized ports,
modify unexpected_intr() accordingly and then use per-port IRQ
handlers instead of per-hwgroup ones.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass 'ide_hwif_t *' instead of 'ide_hwgroup_t *' to unexpected_intr().
* Cache pointer to the port currently being serviced in ->cur_port
and use it instead of hwif->hwgroup on serialized hosts.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix do_ide_request() to operate on previous device / port instead of
the current one. The original code was wrong since at least Feb 2002
(2.4.0 timeframe).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 295f00042a ("ide: don't execute
the next queued command from the hard-IRQ context") overlooked that
ide_do_drive_cmd() (used for REQUEST SENSE command handling) may still
invoke do_ide_request() (->request_fn) in the hard-IRQ context through
blk_start_queueing(). This resulted in a LOCKDEP warning after commit
b599bc7a1199419e122cb2e9ec6b0fa2cfbbc17b ("ide: use per-device request
queue locks (v2)").
Since calling blk_start_queuing() in ide_do_drive_cmd() doesn't make
much sense as the port is already marked as busy (so the execution of
the new command will be deferred anyway) then just remove it fixing
LOCKDEP warning and saving some CPU cycles at the same time.
Reported-and-tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Grissiom <chaos.proton@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove cdrom_do_newpc_cont and cdrom_start_rw_cont wrappers and pass
cdrom_transfer_packet_command to ide_execute_command directly.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: don't move cdrom_start_packet_command() around, remove newlines]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: move cmd_len check closer to ->output_data() call]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As a result, remove now unused ide_scsi_get_timeout and ide_scsi_expiry.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In addition, we wait for DRQ to be asserted by repeatedly polling
device status no matter what DRQ type each device implements.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... by factoring it out of ide_cd_do_request() into a helper, as suggested by
Bart.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: BLK_DEV_IDECD needs to select IDE_ATAPI now]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As planed, this removes ide-scsi.
The 2.6 kernel supports direct writing to ide CD drives, which
eliminates the need for ide-scsi. ide-scsi has been unmaintained and
marked as deprecated.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James.Bottomley@HansenPartnership.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This makes the top-level function just allocate a single pc entry, and then
pass it down as a pointer to all the helper functions that also need one
of those "struct ide_atapi_pc" things. As far as I can tell, the use of
these things never overlaps each other, BUT I DID NOT CHECK VERY CLOSELY!
So I'm not guaranteeing this is correct, and I don't have the hardware. It
would be good for somebody who knows the code more, and has the hardware,
could please test this?
With this, ide-floppy still has fairly big stack usage, but instead of
idefloppy_ioctl [vmlinux]: 1208
ide_floppy_get_capacity [vmlinux]: 872
idefloppy_release [vmlinux]: 408
idefloppy_open [vmlinux]: 408
where those two first ones are at the very top of the list of stack users
for me, it's now
ide_floppy_get_capacity [vmlinux]: 404
ide_floppy_ioctl [vmlinux]: 364
ie they are still high, but they are no longer at the top.
Borislav: Since ide_floppy_get_capacity is passed as a function pointer to other
parts of the kernel (e.g., block layer) we need that ide_atapi_pc to be created
on stack. Also, redid stack users numbers above. The two functions missing from
Linus' original 'make stackusage' output are due to ide being
rewritten/reorganized atm.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move hack for flush requests from choose_drive() to do_ide_request().
* Add ide_plug_device() helper and convert core IDE code from using
per-hwgroup lock as a request lock to use the ->queue_lock instead.
* Remove no longer needed:
- choose_drive() function
- WAKEUP() macro
- 'sleeping' flag from ide_hwif_t
- 'service_{start,time}' fields from ide_drive_t
This patch results in much simpler and more maintainable code
(besides being a scalability improvement).
v2:
* Fixes/improvements based on review from Elias:
- take as many requests off the queue as possible
- remove now redundant BUG_ON()
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_[un]lock_hwgroup() inline helpers for obtaining exclusive
access to the given hwgroup and update the core code accordingly.
[ This change besides making code saner results in more efficient
use of ide_{get,release}_lock(). ]
Cc: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove "paranoia" checks for hwgroup->busy from ide_timer_expiry()
and ide_intr(). This is a preparation for future changes.
Cc: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We now tell block layer that there is still work to do using
blk_plug_device() so hack for IDE Power Management can be removed
(it was buggy for hwgroups having more than 4 devices anyway).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Tell the block layer that we are not done handling requests by using
blk_plug_device() in ide_do_request() (request handling function)
and ide_timer_expiry() (timeout handler) if the queue is not empty.
* Remove optimization which directly calls ide_do_request() for the next
queued command from the ide_intr() (IRQ handler) and ide_timer_expiry().
* Remove no longer needed IRQ masking from ide_do_request() - in case of
IDE ports needing serialization disable_irq_nosync()/enable_irq() was
used for the (possibly shared) IRQ of the other IDE port.
* Put the misplaced comment in the right place in ide_do_request().
* Drop no longer needed 'int masked_irq' argument from ide_do_request().
* Merge ide_do_request() into do_ide_request().
* Remove no longer needed IDE_NO_IRQ define.
While at it:
* Don't use HWGROUP() macro in do_ide_request().
* Use __func__ in ide_intr().
This patch reduces IRQ hadling latency for IDE and improves the system-wide
handling of shared IRQs (which should result in more timeout resistant and
stable IDE systems). It also makes it possible to do some further changes
later (i.e. replace some busy-waiting delays with sleeping equivalents).
v2:
Changes per review from Elias Oltmanns:
- fix wrong goto statement in 'if (startstop == ide_stopped)' block
- use spin_unlock_irq()
- don't use obsolete HWIF() macro
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- media_string() -> ide_media_string()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out device type classifying from do_identify()
to ide_classify_ata_dev() and ide_classify_atapi_dev().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set chipset type explicitly in tx4938ide and tx4939ide host drivers
(all other host drivers were updated already).
* Remove no longer used chipset type fixup from ide_host_register().
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
External driver files should not include any private acpica headers.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (33 commits)
ide-cd: remove dead dsc_overlap setting
ide: push local_irq_{save,restore}() to do_identify()
ide: remove superfluous local_irq_{save,restore}() from ide_dump_status()
ide: move legacy ISA/VLB ports handling to ide-legacy.c (v2)
ide: move Power Management support to ide-pm.c
ide: use ATA_DMA_* defines in ide-dma-sff.c
ide: checkpatch.pl fixes for ide-lib.c
ide: remove inline tags from ide-probe.c
ide: remove redundant code from ide_end_drive_cmd()
ide: struct device - replace bus_id with dev_name(), dev_set_name()
ide: rework handling of serialized ports (v2)
cy82c693: remove superfluous ide_cy82c693 chipset type
trm290: add IDE_HFLAG_TRM290 host flag
ide: add ->max_sectors field to struct ide_port_info
rz1000: apply chipset quirks early (v2)
ide: always set nIEN on idle devices
ide: fix ->quirk_list checking in ide_do_request()
gayle: set IDE_HFLAG_SERIALIZE explictly
cmd64x: set IDE_HFLAG_SERIALIZE explictly for CMD646
ali14xx: doesn't use shared IRQs
...
dsc_overlap setting is not useful anymore for ide-cd so remove
"dsc_overlap" /proc setting, disallow changing the setting through
HDIO_SET_NICE ioctl and cleanup ide_cd{rom_setup,_release}().
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Push local_irq_{save,restore}() from actual_try_to_identify()
to do_identify() and remove no longer needed local_irq_enable().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move legacy ISA/VLB ports handling from ide-probe.c to ide-legacy.c.
* Add CONFIG_IDE_LEGACY config option to be selected by host drivers
needing ide-legacy.c.
v2:
Fix CONFIG_IDE_LEGACY not being defined in Kconfig.
(from Takashi Iwai <tiwai@suse.de>)
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In few places open-coded values were still being used. Fix it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix following errors/warnings detected by checkpatch.pl:
- WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
- WARNING: space prohibited between function name and open parenthesis '('
- ERROR: trailing whitespace
- ERROR: trailing statements should be on next line
- WARNING: printk() should include KERN_ facility level
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt366: set IDE_HFLAG_SERIALIZE in ->host_flags if needed
in init_hwif_hpt366(). Remove HPT_SERIALIZE_IO while at it.
* Set IDE_HFLAG_SERIALIZE in ->host_flags if needed in
ide_init_port().
* Convert init_irq() to use IDE_HFLAG_SERIALIZE together with
hwif->host to find out ports which need to be serialized.
* Remove no longer needed save_match() and ide_hwif_t.serialized.
v2:
* Set host's ->host_flags field instead of port's copy.
This patch should fix the incorrect grouping of port(s) from
host(s) that need serialization with port(s) that happen to use
the same IRQ(s) but are from the host(s) that don't need it.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since CY82C693 doesn't require serialization we may as well
use the default ide_pci chipset type.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRM290 host flag and use it in ide_build_dmatable().
* Remove no longer needed ide_trm290 chipset type.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->max_sectors field to struct ide_port_info to allow host drivers
to specify value used for hwif->rqsize (if smaller than the default).
* Convert pdc202xx_old to use ->max_sectors and remove no longer needed
IDE_HFLAG_RQSIZE_256 flag.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use pci_name(dev) instead of hwif->name in init_hwif_rz1000().
* init_hwif_rz1000() -> rz1000_init_chipset(). Update rz1000_init_one()
to use rz1000_init_chipset() and add now required rz1000_remove().
* Remove superfluous ide_rz1000 chipset type.
v2:
* unsigned int rz1000_init_chipset() -> int rz1000_disable_readahead()
per Sergei's suggestion.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set nIEN for previous port/device in ide_do_request()
also if port uses a non-shared IRQ.
* Remove no longer needed ide_hwif_t.sharing_irq.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix nIEN quirk check to also omit quirky devices using pdc202xx_{new,old}
host drivers for which ->quirk_list == 2.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If IDE doubler is used ports need to be serialized. Currently
init_irq() handles it fine but lets also set IDE_HFLAG_SERIALIZE
host flag explicitly in preparation for future changes.
Also convert the driver to use struct ide_port_info while at it.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set IDE_HFLAG_SERIALIZE explictly for CMD646.
* Remove no longer needed ide_cmd646 chipset type (which has
a nice side-effect of fixing handling of unexpected IRQs).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It doesn't make much sense nowadays and is problematic on some drives.
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Both choose_drive() and PM handling code make sure that the queue
is unplugged so no need to check it again.
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now that (almost) all host drivers have been fixed not to abuse ide_lock
and core code usage of ide_lock has been sanitized we may safely replace
ide_lock by per-hwgroup locks.
This patch is partially based on earlier patch from Ravikiran G Thirumalai.
While at it:
- don't use deprecated HWIF() and HWGROUP() macros
- update locking documentation in ide.h
v2:
Add missing spin_lock_init(&hwgroup->lock). (Noticed by Elias Oltmanns)
Cc: Vaibhav V. Nivargi <vaibhav.nivargi@gmail.com>
Cc: Alok N. Kataria <alokk@calsoftinc.com>
Cc: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is just a preparation for future changes and there should be no
functional changes caused by this patch since ide_lock is currently
also used as queue lock.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use blk_end_request() instead of ide_lock + __blk_end_request()
in cdrom_end_request(), cdrom_newpc_intr(), __ide_end_request(),
ide_complete_pm_request() and ide_end_drive_cmd().
[ ide_lock is currently also used as queue lock ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE settings are protected by ide_setting_mtx mutex so there is
no need to hold ide_lock in ide_setting_ioctl(), ide_read_setting()
and ide_proc_unregister_driver().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just a preparation for future changes.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Commit 4dde4492d8 ("ide: make drive->id
an union (take 2)") accidentally introduced an IDE ACPI regression which
at least on some machines confuses ACPI and breaks suspend. Fix it.
Fixes kernel.org bug #12279:
http://bugzilla.kernel.org/show_bug.cgi?id=12279
[ Sorry about the bug (IDE ACPI is not used by default so it managed
to slip in). Still it is kind of surprising that the bug breaks
suspend as it shouldn't impact anything except IDE ACPI (it seems
that it uncovered either some ACPI/PM deficiency or a BIOS bug). ]
Reported-and-bisected-by: David Roka <roka@dawid.hu>
Tested-by: David Roka <roka@dawid.hu>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This fixes data corruption on PIO mode.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: stable <stable@kernel.org>
Cc: sshtylyov@ru.mvista.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This fixes data corruption on some heavy load.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: stable <stable@kernel.org>
Cc: sshtylyov@ru.mvista.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove some more cruft from machw.h and drop the #include where it isn't
needed.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The generic_defconfig has three section mismatches. This clears up
ioc4_ide_attach_one().
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Mike Reid <mdr@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
IDE pmac host driver build fails with CONFIG_BLK_DEV_IDEDMA_PMAC=n
as reported by Kamalesh:
> drivers/ide/pmac.c: In function 'pmac_ide_set_pio_mode':
> drivers/ide/pmac.c:527: error: implicit declaration of function 'kauai_lookup_timing'
> drivers/ide/pmac.c:527: error: 'shasta_pio_timings' undeclared (first use in this function)
> drivers/ide/pmac.c:527: error: (Each undeclared identifier is reported only once
> drivers/ide/pmac.c:527: error: for each function it appears in.)
> drivers/ide/pmac.c:534: error: 'kauai_pio_timings' undeclared (first use in this function)
> drivers/ide/pmac.c: In function 'pmac_ide_do_resume':
> drivers/ide/pmac.c:914: error: 'IDE_WAKEUP_DELAY' undeclared (first use in this function)
> drivers/ide/pmac.c: At top level:
> drivers/ide/pmac.c:1007: error: 'pmac_ide_init_dma' undeclared here (not in a function)
> drivers/ide/pmac.c: In function 'pmac_ide_setup_device':
> drivers/ide/pmac.c:1107: error: 'IDE_WAKEUP_DELAY' undeclared (first use in this function)
> drivers/ide/pmac.c: In function 'pmac_ide_macio_attach':
> drivers/ide/pmac.c:1209: error: 'pmac_ide_hwif_t' has no member named 'dma_regs'
> drivers/ide/pmac.c:1210: error: 'pmac_ide_hwif_t' has no member named 'dma_regs'
> make[2]: *** [drivers/ide/pmac.o] Error 1
Fix it by removing the superfluous config option.
Reported-and-tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This reverts commit e9eb838830 since
it could break resume (thanks to Paul Collins for the report).
I'll look into sorting this out properly for 2.6.29
but for 2.6.28 it is the best to just revert my patch.
Reported-by: Paul Collins <paul@burly.ondioline.org>
Cc: rjw@sisk.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We guarantee 400ns delay at the time of issuing the command.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also while at it:
* Drop unused arguments from ide_complete_power_step().
* Move DEBUG_PM printk() from ide_end_drive_cmd() to
ide_complete_power_step().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode. In order to achieve this:
* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.
* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
driver for nVidia controllers in Compatibility Mode.
* Teach actual_try_to_identify() and drive_is_ready() about the new flag.
This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).
[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
and distributions use) it never worked correctly. ]
Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.
More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659http://bugzilla.kernel.org/show_bug.cgi?id=10216
Reported-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Lars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
icside_register_v[56] is called from (__devinit) icside_probe
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CLPS7500 platform has not built since 2.6.22-git7 and there
seems to be no interest in fixing it. So, remove the platform
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for Apacer photo steno pro card.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk
CC: linux-ide@vger.kernel.org
We need to re-get a removable media's capacity when revalidating the
disk so that its partitions get rescanned by the block layer.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: axboe@kernel.dk
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make 'wt' variable signed while it can be negative during calculation.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: sshtylyov@ru.mvista.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Call devm_ioremap() for CS0 and CS1 separetely.
And some style cleanups.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: ralf@linux-mips.org
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
SHWT value is used as address valid to -CSx assertion and -CSx to -DIOx
assertion setup time, and contrarywise, -DIOx to -CSx release and -CSx
release to address invalid hold time, so it actualy applies 4 times and
so constitutes -DIOx recovery time. Check requirement of the recovery
time and cycle time. Also check SHWT maximum value.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: ralf@linux-mips.org
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
e5318b531b ("ide: use the dma safe check for
REQ_TYPE_ATA_PC") introduced a regression which caused some ATAPI drives to
turn off DMA for REQ_TYPE_BLOCK_PC commands while burning and thus degrading
performance and ultimately causing an excessive amount of underruns.
The issue is documented also in:
http://bugzilla.kernel.org/show_bug.cgi?id=11742.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Valerio Passini <valerio.passini@unicam.it>
[bart: fixup patch description per comments from Sergei Shtylyov]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
