ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The station control register must depend on both the advertisement and the lpa
The link partner ability has better be intersected with the current
advertised value before it is feed to the station control register.
Sight-catched-by: Lars Vahlenberg <lars.vahlenberg@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added PHY identifier for the Asus K8S-MX motherboard
Note: the same ID appears in the sis900 driver.
Signed-off-by: Lars Vahlenberg <lars.vahlenberg@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a dummy read before accessing the status register
SiS driver suggests it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Allow a non-hardcoded ID for the PHY
This is the first step before the driver probes for the PHY address.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
extract bits definition from SiS driver
- fix the Rx stats;
- minor pieces of documentation.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a restriction to the size of the Rx buffer
SiS driver forces the size of any Rx buffer to be a multiple of 64 bit.
I would not be surprized that it goes along with some alignment issues
which have been experienced before. So far it does not make much of a
difference (both drivers use 1536 bytes buffer).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Extract some mac addr code from SiS's driver.
Some magic may hide beyond the isa bridge. The Rx mac control
register is now set without condition.
Note: good or bad, this part of the code is quite close to sis900.c.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace hardcoded constants by enumerated values in sis190_read_eeprom
The names of the enumerated values have been extracted from SiS'official
driver (v1.00.00 published on 2005/07/11).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Merge some register related information from SiS driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethtool/mii support
Bug: disabling autonegotiation and setting the link parameters at the
same time does not provide the expected result. More investigation is
needed.
Note: past the initial probe/open time, the link is managed from user-space
or accessed through sis190_phy_task, i.e. in a usermode context. Whence the
very limited locking needs.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
netconsole support.
This stuff should be factored out of every driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Raise the sis190 driver from the dead
The driver handles the integrated network device found on SiS 965L
chipset. It follows the classical (non-napi) interrupt-driven model
and provides minimal ethtool support.
The code comes from a heavy cleanup/rewrite of the original code
which was removed from the kernel on 14/04/2004. Since the r8169
driver does not work too bad and there will probably be (at least)
a few months of improvements/testing/fixing, I made the code as
close as possible to the r8169 one.
Pascal Chapperon <pascal.chapperon@wanadoo.fr> deserves some special
credit for testing and bug-catching. Many thanks to Lars Vahlenberg
as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed beacon frame when moving from monitor mode to master mode
(workaround for firmware bug that left IBSS IE in the Beacon
frames). This is using the same workaround that was previously used
when moving from adhoc mode to master mode.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Warning fix for 64-bit platforms
Hello!
The patch fixes following warning seen on 64-bit platforms (in my case -
x86_64, gcc-4.0):
In file included from /usr/local/src/hostap/driver/modules/hostap_cs.c:203:
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit_cb?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1674: warning: cast from pointer to integer of different size
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1758: warning: cast to pointer from integer of different size
prism2_transmit_cb uses a (void *) argument to get an integer. A
simple fix would be to use double cast from pointer to long and then to
int (and vice versa when int is passed as a pointer). But I prefer a
slightly longer patch.
I believe that whenever an argument can hold both a pointer and an
integer, it should be declared long. long can hold both pointers and
integers (except win64, but we are not coding for Windows), it can be
cast to both of them and it's never assumed to be a valid pointer, which
could be useful for some automatic code checkers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
line 129 of hostap_80211_rx.c should read:
LWNG_SETVAL(mactime, 2, 0, 4, rx_stats->mac_time);
not:
LWNG_SETVAL(mactime, 2, 0, 0, rx_stats->mac_time);
The length field is incorrect.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Firmware seems to be getting into odd state in host_roaming mode 2
when hostscan is used without join command, so try to fix this by
re-joining the current AP. This does not actually trigger a new
association if the current AP is still in the scan results.
This makes background scans (iwlist wlan0 scan) not to break data
connection when in host_roaming 2 mode, e.g., when using wpa_supplicant.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleaned up scan result processing by converting struct
hfa384x_scan_result into struct hfa384x_hostscan_result. This removes
special cases from result processing since the results are only used
in one, hostscan, format.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added support for setting channel mask for scan requests
('iwpriv wlan0 scan_channels 0x00ff' masks scans to use channels 1-8).
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add MODULE_VERSION information for the Host AP kernel modules and
update the version string to indicate which version of the external
Host AP driver is included in the kernel tree.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
pcmcia id_table for hostap_cs.c
Hi Jouni,
Here's a patch for adding a pcmcia id_table to hostap_cs.c as introduced
by the PCMCIA subsystem changes in linux-2.6.13-rc1. The id_table allows
hotplug (along with pcmciautils [1]) to load the driver without the need
for the pcmcia-cs cardmgr daemon.
The id_table was generated from the CVS version of hostap_cs.conf using
a script borrowed from Dominik Brodowski. I have removed any duplicate
entries, but I have only been able to test the functionality of the
patch with a Linksys WPC11v3.
Sincerely,
Brix
[1]: http://www.kernel.org/pub/linux/utils/kernel/pcmcia/
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Create sysfs "device" files for hostap
I was writing some scripts to automatically build kismet source lines,
and I noticed that hostap devices don't have device files, unlike my
prism54 and ipw2200 cards:
$ ls -l /sys/class/net/eth0/device
/sys/class/net/eth0/device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:02:01.0
$ ls -l /sys/class/net/wifi0
ls: /sys/class/net/wifi0/device: No such file or directory
$ ls -l /sys/class/net/wlan0
ls: /sys/class/net/wlan0/device: No such file or directory
The following (quite small) patch makes sure that both the wlan and wifi
net devices have that pointer to the bus device.
This way, I can do things like
for i in /sys/class/net/*; do
if ! [ -e $i/device/drive ]; then
continue;
fi;
driver=$(basename $(readlink $i/device/driver))
case $driver in
hostap*)
echo -- hostap,$i,$i-$driver
break;
ipw2?00)
echo -- $driver,$i,$i-$driver
break;
prism54)
echo prism54g,$i
esac
done
Which should generate a working set of source lines for kismet no matter
what order I plug the cards in.
It might also be handy to have a link between the two net devices, but
that's a patch for another day.
That patch is against 2.6.13-rc1-mm1.
-- Dave
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_cs: Remove irq_list, irq_mask and pcmcia/version.h
Remove irq_list, irq_mask and pcmcia/version.h as suggested in
http://kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
EXPORT_SYMTAB does nothing. There's no need to define something if it
doesn't have any effect.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update hostap_cs to use new PCMCIA event callback registration.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
An early version of the sk98lin patch was merged via Len's tree. But there
were subsequent updates as a result of review from Jeff. THis fixes things
up.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We want to extract our LAN card driver from tulip core driver and
make a new file uli526x.c at tulip folder, because we have added
some ethtool interface support and non-eprom support in our driver
and may be other change in the futher.
If our controllers support are still contained in the tulip core
driver, I think it'll increase the complexity of maintenance, you
know, tulip core driver include several files and support so many
other controllers. Furthermore, I tested the newest kernel 2.6.12
and I found the tulip driver can not work on our lan controller, and
I no time to debug it, so I aspired want to make a single uli526x.c
file just for our controllers. Could you help us remove the ULi
m5261/m5263 lan controller support from tulip core driver and add
the new single uli526x.c file for us?
Signed-off-by: Peer Chen <Peer.Chen@uli.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sys_reboot() now calls device_suspend(), so it is no longer necessary for
the e1000 driver to register a reboot notifier [in fact doing so results in
e1000_suspend() getting called twice].
(akpm: we need to fast-track this. It's causing ia64 to oops on shutdown)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <cramerj@intel.com>
Cc: <john.ronciak@intel.com>
Cc: <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicates from the device id table.
Signed-off-by: Jarkko Raja <jar@pcuf.fi>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move in_aton to allow netpoll and pktgen to work without the rest of
the IPv4 stack. Fix whitespace and add comment for the odd placement.
Delete now-empty net/ipv4/utils.c
Re-enable netpoll/netconsole without CONFIG_INET
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggestion from Sam Ravnborg <sam@ravnborg.org>
It causes all driver families to be displayed aligned immediately under the
main network drivers heading (in menuconfig/xconfig/gconfig) instead of
not being subordinate to (i.e., not indented) the Network device support
heading at all.
The improved network driver families are:
token ring, wireless, PCMCIA, WAN, ATM, and S390.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780S support by adding a new tg3_setup_fiber_mii_phy() function and
a timer function for parallel link detection. 5780S uses standard MII
registers for 1000BaseX and runs in GMII mode as opposed to TBI mode on
older serdes chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disallow jumbo TSO on 5780 due to hardware restrictions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all DMA watermark settings for standard and jumbo frames on
all chips in tg3_init_bufmgr_config() and add new settings for 5780.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rx_pkt_buf_sz to the tg3 structure to support variable buffer
sizes on the standard ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic jumbo frames support for 5780. This chip supports jumbo frames
on the standard receive ring without the jumbo ring. The
TG3_FLAG_JUMBO_ENABLE is changed to TG3_FLAG_JUMBO_RING_ENABLE to
indicate using the jumbo ring on 5704 and older chips. A new
TG3_FLG2_JUMBO_CAPABLE flag is added to indicate jumbo frames support
with or without the jumbo ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780 PCI IDs, chip IDs, and other basic support.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETCONSOLE=y and INET=n results in the following compile error:
net/built-in.o: In function `netpoll_parse_options':
: undefined reference to `in_aton'
net/built-in.o: In function `netpoll_parse_options':
: undefined reference to `in_aton'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put NETCONSOLE and NETPOLL options together since they are related.
This cuts down on the hassle of flipping back and forth between
the Networking menu and the Network drivers menu to change their
config settings.
Tested with menuconfig, gconfig, and xconfig.
gconfig has a small problem with this. I think that it's
a bug in gconfig and I will take it up with Romain Lievin.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Use of the time_after() macro, defined at linux/jiffies.h, which deal
with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Use of the time_after() macro, defined at linux/jiffies.h, which deal
with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tr_type_trans(), hippi_type_trans() left as-is.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the protocol specific config options out to the specific protocols.
With this change net/Kconfig now starts to become readable and serve as a
good basis for further re-structuring.
The menu structure is left almost intact, except that indention is
fixed in most cases. Most visible are the INET changes where several
"depends on INET" are replaced with a single ifdef INET / endif pair.
Several new files were created to accomplish this change - they are
small but serve the purpose that config options are now distributed
out where they belongs.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should do this:
.suspend()
pci_disable_device()
.resume()
pci_enable_device()
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Few more u32 vs. pm_message_t fixes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for some new PHY models to sungem as used on some
recent Apple iMac G5 models.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the usage of struct of_match to struct of_device_id,
similar to pci_device_id. This allows a device table to be generated,
which can be parsed by depmod(8) to generate a map file for module
loading.
In order for hotplug to work with macio devices, patches to
module-init-tools and hotplug must be applied. Those patches are
available at:
ftp://ftp.suse.com/pub/people/jeffm/linux/macio-hotplug/
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave, you were right and the sleeping locks in shaper were
broken. Markus Kanet noticed this and also tested the patch below that
switches locking to spinlocks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool -C with verification of user parameters.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Nicolas Pitre
Those are big, slow and generally not recommended for kernel code.
They are even not present on i386. So it should be concluded that
one could as well get away with do_div() alone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many drivers use skb->tail unnecessarily.
In these situations, the code roughly looks like:
dev = dev_alloc_skb(...);
[optional] skb_reserve(skb, ...);
... skb->tail ...
But even if the skb_reserve() happens, skb->data equals
skb->tail. So it doesn't make any sense to use anything
other than skb->data in these cases.
Another case was the s2io.c driver directly mucking with
the skb->data and skb->tail pointers. It really just wanted
to do an skb_reserve(), so that's what the code was changed
to do instead.
Another reason I'm making this change as it allows some SKB
cleanups I have planned simpler to merge. In those cleanups,
skb->head, skb->tail, and skb->end pointers are removed, and
replaced with skb->head_room and skb->tail_room integers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Now we can change the pci core to always set this pointer, as pci drivers
should use it, not the driver core callback.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
More fixes for greg depredations.
Also nuke lots of pointless typecasts.
All this new wireless code adds near-infinite amounts of trailing whitespace.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/wireless/ipw2100.c: In function `ipw2100_set_key_index':
drivers/net/wireless/ipw2100.c:5326: array index in non-array initializer
drivers/net/wireless/ipw2100.c:5326: (near initialization for `cmd')
drivers/net/wireless/ipw2100.c:5326: warning: missing braces around initializer
drivers/net/wireless/ipw2100.c:5326: warning: (near initialization for `cmd.host_command_parameters')
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix few typos/thinkos in ipw, remove ugly macro (it is commented around,
anyway), and fix types passed to pci_set_power_state.
Signed-off-by: Andrew Morton <akpm@osdl.org>
There are several never used macros in ipw2100. This removes them.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
ipw2100 still has support for old kernels. Thats considered bad for patch in
mainline... this fixes few instances.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom macros.
This patch includes dma-mapping.h explicitly because it caused errors on some
architectures otherwise. See
http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom macros.
This patch includes dma-mapping.h explicitly because it caused errors on some
architectures otherwise. See
http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
On Mon, 06 Jun 2005 14:29:52 +0800, Zhu Yi wrote:
> ("%zd", sizeof()) should be better.
Thanks. This is a corrected version of the patch.
This patch fixes warnings when compiling ipw2100 and ipw2200 on x86_64.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: Jirka Bohac <jbohac@suse.cz>
This results in recursive dependencies:
- IPW2200 depends on NET_RADIO
- IPW2200 selects IEEE80211
- IEEE80211 selects NET_RADIO
This patch fixes the IPW2200 dependencies in a way that they are similar
to the IPW2100 dependencies.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
The amd8111e driver directly assigns the DMA mask to the dma_mask
member of the struct pci_dev instead of using pci_set_dma_mask(). This
makes the call to pci_dma_supported() redundant as pci_set_dma_mask()
does this check.
I do not own this device so I only compile-tested this patch.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
For boards that invert the SMC91x IRQ line (maybe an FPGA inverts it),
the set_irq_type() call can't assume IRQT_RISING. These particular
boards currently use OMAP-specific calls to change the trigger type,
but the boards break when set_irq_type() stops being a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add new pcmcia id_table for fmvj18x_cs and serial_cs.
(TDK multi-function card (NetPartner9610 and MobileNetworker3200))
Signed-off-by: Jun Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to handle receive and transmit packet arbiter timeouts.
Transmit arbiter timeouts happens when Gigabit sends to 100Mbit port
on same switch and pause occurs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Cleanup messages (for debug) about PHY interrrupts, because when
user can't get driver working that is often the problem.
Use a consistent way of enabling interrupts by port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Rewrite the code for handling the Broadcom PHY to something that
works. Remove link polling because Broadcom and Yukon don't need it.
When I wrote initial code, didn't have a genesis chipset based
board to test, so it was a non-working guess.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Remove support for the non-Broadcom genesis based boards. The code
is untested, and probably won't work as is. The newer boards are all
Yukon based, and only old Genesis board I can find uses Broadcom.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Remove the bits and pieces added relating to Yukon II chipset.
The Yukon 2 will be in a separate driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Replace inline accessor functions for chip revision and number of ports
with simple structure members.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The inlines and macro's needed some cleanup's and fixes:
* change name of macro SKGEMAC_REG to SK_REG to better reflect usage
and fix comments
* ditto for SK_GEXM_REG -> SK_XMAC_REG and SKGEGMA_REG -> SK_GMA_REG
* change skge_gm_ to just gm_ since it is just a local function and long
names look ugly.
* change skge_xm_ to just xm_
* fix xm_write32 to write as two u16's with correct byte order
* fix xm_outaddr to correctly use offset
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Check the link state during b44_open. This closes a 1 HZ window
that existed after b44_open ran but before the b44_timer handler ran,
during which ethtool would report "Link detected: yes" no matter what
the link state actually was.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the tulip driver to suspend and resume properly. It was
originally written by Karsten Keil and then modified by Adam Belay.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/wireless/prism54/isl_38xx.c:131: warning: 'current_time.tv_sec' is used uninitialized in this function
drivers/net/wireless/prism54/isl_38xx.c:131: warning: 'current_time.tv_usec' is used uninitialized in this function
Signed-off-by: Olaf Hering <olh@suse.de>
Jeff,
Just incase this got lost in the recent netdev mailing list transition
here is a nicer version of Andy's patch for gianfar.
- kumar
* TCP/IP/UDP checksumming and verification
* VLAN tag insertion/extraction
* Larger multicast hash-table
* Padding to align IP headers
Also added:
* msg lvl support
* Some whitespace cleanup
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
The race causes a kernel oops when smc_hardware_send_pkt() tries to
dereference pending_tx_skb which would have been freed from one of the
driver reset paths just after the tx_task tasklet has been scheduled.
This race is possible on SMP but was uncovered by the kernel RT work.
Signed-off-by: Nicolas Pitre <nico@cam.org>
--Boundary-00=_F5lsC5eH1wGW5o9
Content-Type: text/plain;
charset="koi8-r"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
Hi Jeff,
In some messages in via-rhine.c there is a leading space
for no apparent reason. This patch removes it.
--
vda
--Boundary-00=_F5lsC5eH1wGW5o9
Content-Type: text/x-diff;
charset="koi8-r";
name="via-rhine.c.diff"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
filename="via-rhine.c.diff"
Driver version, white space, comments & other
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Included proposals to false late collisions due to H/W latencies
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Ethtool set speed/duplex validates parameters for consistency
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Ethtool cleanup patch from Stephen Hemminger
* use ADVERTISED_xxx fields when setting advertised fields
* don't hardcode constant for advertised field
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed the loopback test failure for 82573 based adapters
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed register and loopback test failures with 82573 controllers
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Cleanup debug message printed when Tx Unit hang is detected
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use netdev_priv() to get to netdev->priv - from shemminger@osdl.org
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use correct WOL settings for 82544 adapters
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
NAPI performance enhancements - Fixed issues with shared interrupts and NAPI resulting in bad performance.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
e100_eeprom_load was called after e100_phy_init causing phy_init
not to use values set in EEPROM - from emann@mrv.com
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Added patch from Eran Mann to fix following e100 MDI/MDI-X issues
* MDI/MDI-X autodetection should never be enabled for 82551ER/QM chips
* enabling this feature based on eeprom settings
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
If the frame has ToDS flag set, mark it by setting skb->pkt_type to
PACKET_OTHERHOST, so that applications unaware of promiscous mode won't get
uplink (STA->AP) packets for STA->STA transmissions relayed by the AP.
Thanks to John Denker and David Gibson for finding the problem and the
solution.
Patch from Pavel Roskin
This patch is to provide support for cs89x0-based network device on
Philips' pnx0105 board.
Signed-off-by: dmitry pervushin <dpervushin@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use ssleep() / msleep_interruptible() [as appropriate]
instead of schedule_timeout() to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Use msleep_interruptible() instead of schedule_timeout() to
guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Insert set_current_state() before schedule_timeout() so the
function delays as expected. Without the addition, schedule_timeout()
will return immediately.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Use ssleep() instead of nicedelay()
to guarantee the task delays as expected. Remove the prototype and
definition of nicedelay(). This is a very weird function, because it is
called to sleep in terms of usecs, but always sleeps for 1 second,
completely ignoring the parameter. I have gone ahead and followed suit,
just sleeping for a second in all cases, but maybe someone with the
hardware could tell me if perhaps the paramter *should* matter. Additionally,
nicedelay() is called in TASK_INTERRUPTIBLE state, but doesn't deal with signals
in case these longer delays do not complete, so I believe ssleep() is more
appropriate.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
This patch fixes two bugs in the dm9000 network driver:
- Don't read one byte too much in 8bit mode.
- release correct resource
Signed-off-by: Jochen Karrer <j.karrer@lightmaze.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix int vs. pm_message_t confusion in airo. Should change no code.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This is a fix for the interrupt handler in the defxx driver to use
irqreturn_t. Beside the obvious fix of returning a proper status at all,
it actually checks board registers as appropriate for determining if an
interrupt has been recorded in the bus-specific interface logic.
The patch also includes an obvious one-line fix for SET_NETDEV_DEV needed
for the EISA variation, for which I've decided there is no point in sending
separately.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/tulip/dmfe.c: In function `dmfe_parse_srom':
drivers/net/tulip/dmfe.c:1805: warning: passing arg 1 of `__le16_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
This is basically a guess:
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The 8129/8130 support is a sub-option that is not visible if the user
hasn't enabled the 8139 support.
Let's make it a bit easier for users to find the driver for their nic.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch contains the follwing cleanups:
- make needlessly global code static
- remove obsolete Emacs settings
Signed-off-by: Adrian Bunk <bunk@stusta.de>
During some performance diagnostics I stumbled on this slightly wasteful
code in pcnet_cs.c which I made the patch included at the bottom for (two
minor comment fixes included).
Improvement:
instead of *always* calculating
lea 0x2c0(%edx),%ebx
and then additionally doing the
mov %edx,0xc0(%ebx)
addition *if we need it*,
we now do the *whole* calculation of
mov %edx,0x380(%ebx)
*only* if we need it.
This even manages to save us a whole 16-byte alignment buffer loss
in this compilation case.
Result: slightly improves IRQ handler performance in both shared and
non-shared IRQ case, which should make my rusty P3/700 a slight bit happier.
Thank you for your support,
Andreas Mohr
old asm result (using gcc 3.3.5):
000015a0 <ei_irq_wrapper>:
15a0: 55 push %ebp
15a1: 89 e5 mov %esp,%ebp
15a3: 53 push %ebx
15a4: 8d 9a c0 02 00 00 lea 0x2c0(%edx),%ebx
15aa: e8 fc ff ff ff call 15ab <ei_irq_wrapper+0xb>
15af: 83 f8 01 cmp $0x1,%eax
15b2: 74 03 je 15b7 <ei_irq_wrapper+0x17>
15b4: 5b pop %ebx
15b5: 5d pop %ebp
15b6: c3 ret
15b7: 31 d2 xor %edx,%edx
15b9: 89 93 c0 00 00 00 mov %edx,0xc0(%ebx)
15bf: eb f3 jmp 15b4 <ei_irq_wrapper+0x14>
15c1: eb 0d jmp 15d0 <ei_watchdog>
15c3: 90 nop
15c4: 90 nop
15c5: 90 nop
15c6: 90 nop
15c7: 90 nop
15c8: 90 nop
15c9: 90 nop
15ca: 90 nop
15cb: 90 nop
15cc: 90 nop
15cd: 90 nop
15ce: 90 nop
15cf: 90 nop
000015d0 <ei_watchdog>:
new asm result:
000015a0 <ei_irq_wrapper>:
15a0: 55 push %ebp
15a1: 89 e5 mov %esp,%ebp
15a3: 53 push %ebx
15a4: 89 d3 mov %edx,%ebx
15a6: e8 fc ff ff ff call 15a7 <ei_irq_wrapper+0x7>
15ab: 83 f8 01 cmp $0x1,%eax
15ae: 74 03 je 15b3 <ei_irq_wrapper+0x13>
15b0: 5b pop %ebx
15b1: 5d pop %ebp
15b2: c3 ret
15b3: 31 d2 xor %edx,%edx
15b5: 89 93 80 03 00 00 mov %edx,0x380(%ebx)
15bb: eb f3 jmp 15b0 <ei_irq_wrapper+0x10>
15bd: 8d 76 00 lea 0x0(%esi),%esi
000015c0 <ei_watchdog>:
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Make sure the code compiles with and without ARLAN_ENTRY_EXIT_DEBUGGING.
Only provide parameter descriptions when parameters are defined.
Remove "arlan_"-prefix to shape up built-in parameter names:
arlan.arlan_debug -> arlan.debug
arlan.arlan_EEPROM_bad -> arlan.EEPROM_bad
arlan.arlan_entry_and_exit_debug -> arlan.entry_and_exit_debug
arlan.arlan_entry_debug -> arlan.entry_debug
arlan.arlan_exit_debug -> arlan.exit_debug
Signed-off-by: Magnus Damm <damm@opensource.se>
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom
macros.
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
The spin loop in 8139cp is limited to 100 iterations when pulling hardware
stats. There is no allowance for processor speed so on a fast machine, the
stats may not be available that fast. Also, if the board doesn't return
soon enough make sure turn the address back off to prevent later updates
when memory has gone away.
Add support for alternate slave selection algorithms to bonding
balance-xor and 802.3ad modes. Default mode (what we have now: xor of
MAC addresses) is "layer2", new choice is "layer3+4", using IP and port
information for hashing to select peer.
Originally submitted by Jason Gabler for balance-xor mode;
modified by Jay Vosburgh to additionally support 802.3ad mode. Jason's
original comment is as follows:
The attached patch to the Linux Etherchannel Bonding driver modifies the
driver's "balance-xor" mode as follows:
- alternate hashing policy support for mode 2
* Added kernel parameter "xmit_policy" to allow the specification
of different hashing policies for mode 2. The original mode 2
policy is the default, now found in xmit_hash_policy_layer2().
* Added xmit_hash_policy_layer34()
This patch was inspired by hashing policies implemented by Cisco,
Foundry and IBM, which are explained in
Foundry documentation found at:
http://www.foundrynet.com/services/documentation/sribcg/Trunking.html#112750
Signed-off-by: Jason Gabler <jygabler@lbl.gov>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Add support for generating gratuitous ARPs in bonding
active-backup mode when failovers occur. Includes support for VLAN
tagging the ARPs as needed.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
wanpipe.txt and wan-router.txt in Documentation/networking contain the exact
same information (diff between the two shows no drivers/net/wan/Kconfig.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Move tp->irq_sync = 0 to before the interrupt mailbox IO in
tg3_enable_ints() so that the interrupt handler will always see
irq_sync == 0 when interrupts are enabled.
2. Remove the tg3_enable_ints() call in tg3_reset_hw(). Interrupts are
always enabled explicitly or through tg3_netif_start(). This is to
prevent interrupts being enabled while poll is disabled.
3. Update trans_start with jiffies in tg3_netif_stop() to prevent false
NETDEV WATCHDOG.
4. Pass in the proper irq_sync parameter to tg3_full_lock() depending on
netif_running() in some of the ethtool set calls.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all driver spinlocks to be taken at sw IRQ
context only.
This fixes the skb_copy() we were doing with hw
IRQs disabled (which is illegal and triggers a
BUG() with HIGHMEM enabled). It also simplifies
the locking all over the driver tremendously.
We accomplish this feat by creating a special
sequence to synchronize with the hw IRQ handler
using a binary state and synchronize_irq().
This idea is from Herbert Xu.
Thanks to Michael Chan for helping to track down
all of the race conditions in initial versions
of this code.
Signed-off-by: David S. Miller <davem@davemloft.net>
There must be a rmb() between reading the status block tag
and calling tg3_has_work(). This was missing in tg3_mis()
and tg3_interrupt_tagged(). tg3_poll() got it right.
Also, SD_STATUS_UPDATED must be cleared in the status block
right before we call tg3_has_work(). Only tg3_poll() got this
wrong.
Based upon patches and commentary from Grant Grundler and
Michael Chan.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can avoid assignments to the local variable 'tmp' and
actually get rid of tmp alltogether in sl_free_bufs(). This patch does
that. This is safe since both kfree() and slhc_free() handles NULL
pointers gracefully.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an obvious and nasty bug where we could exit the transmit
routine while holding tx_lock.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
- Use extern prefix for functions required.
- Removed a lot of wrappers, including t1_read/write_reg_4.
- Removed various macros, using native kernel calls now.
- Enumerated various #defines.
- Removed a lot of shared code which is not currently used in "NIC only" mode.
- Removed dead code.
Documentation/networking/cxgb.txt:
- Updated release notes for version 2.1.1
drivers/net/chelsio/ch_ethtool.h
- removed file, no longer using ETHTOOL namespace.
drivers/net/chelsio/common.h
- moved code from osdep.h to common.h
- added comment to #endif indicating which symbol it closes.
drivers/net/chelsio/cphy.h
- removed dead code.
- added comment to #endif indicating which symbol it closes.
drivers/net/chelsio/cxgb2.c
- use DMA_{32,64}BIT_MASK in include/linux/dma-mapping.h.
- removed unused code.
- use printk message for link info resembling drivers/net/mii.c.
- no longer using the MODULE_xxx namespace.
- no longer using "pci_" namespace.
- no longer using ETHTOOL namespace.
drivers/net/chelsio/cxgb2.h
- removed file, merged into common.h
drivers/net/chelsio/elmer0.h
- removed dead code.
- added various enums.
- added comment to #endif indicating which symbol it closes.
drivers/net/chelsio/espi.c
- removed various macros, using native kernel calls now.
- removed a lot of wrappers, including t1_read/write_reg_4.
drivers/net/chelsio/espi.h
- added comment to #endif indicating which symbol it closes.
drivers/net/chelsio/gmac.h
- added comment to #endif indicating which symbol it closes.
drivers/net/chelsio/mv88x201x.c
- changes to sync with Chelsio TOT.
drivers/net/chelsio/osdep.h
- removed file, consolidation. osdep was used to translate wrapper functions
since our code supports multiple OSs. removed wrappers.
drivers/net/chelsio/pm3393.c
- removed various macros, using native kernel calls now.
- removed a lot of wrappers, including t1_read/write_reg_4.
- removed unused code.
drivers/net/chelsio/regs.h
- added a few register entries for future and current feature support.
- added comment to #endif indicating which symbol it closes.
drivers/net/chelsio/sge.c
- rewrote large portion of scatter-gather engine to stabilize
performance.
- using u8/u16/u32 kernel types instead of __u8/__u16/__u32 compiler
types.
drivers/net/chelsio/sge.h
- rewrote large portion of scatter-gather engine to stabilize
performance.
- added comment to #endif indicating which symbol it closes.
drivers/net/chelsio/subr.c
- merged tp.c into subr.c
- removed various macros, using native kernel calls now.
- removed a lot of wrappers, including t1_read/write_reg_4.
- removed unused code.
drivers/net/chelsio/suni1x10gexp_regs.h
- modified copyright and authorship of file.
- added comment to #endif indicating which symbol it closes.
drivers/net/chelsio/tp.c
- removed file, merged into subr.c.
drivers/net/chelsio/tp.h
- removed file.
include/linux/pci_ids.h
- patched to include PCI_VENDOR_ID_CHELSIO 0x1425, removed define from
our code.
Use ssleep() / msleep() [as appropriate]
instead of schedule_timeout() to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an obsolete header file include/asm-m32r/m32102peri.h.
In this header, there are some undesirable single character types, like V.
And the header is almost no longer used.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the superfluous test of "if (vortex_debug > 3)" inside the "if
(vortex_debug > 6)" clause early in boomerang_start_xmit.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a fixed-up version of the broken "upstream-2.6.13" branch, where
I re-did the manual merge of drivers/net/r8169.c by hand, and made sure
the history is all good.
From: Ralf Baechle <ralf@linux-mips.org>
There are archives of the old list at http://oss.sgi.com/archives/netdev
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
My patch from a few weeks back (now in mainline), called "Cleanup skbs to
prevent unregister_netdevice() hanging", can cause our TX timeout code to
fire on machines with lots of VLANs (because it takes > 2 seconds between
when we stop the queues and when we're finished stopping the connections).
When that happens the TX timeout code freaks out and does a WARN_ON()
because as far as it's concerned there shouldn't be a TX timeout happening,
which is fair enough.
I have a "proper" fix for this, which is to a) do refcounting on
connections and b) implement a proper ack timer so we don't keep unacked
skbs lying around for ever. But for 2.6.12 I propose just supressing the
WARN_ON(). Users will still see the "NETDEV WATCHDOG" warning, but that's
not nearly as bad as a WARN_ON() which users interpret as an Oops.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix 5700/5701 DMA write corruption on Apple G4 by detecting the Apple
UniNorth PCI 1.5 chipset and adjusting the DMA write boundary to 16. DMA
test fails to detect the problem with this chipset.
Thanks to Manuel Perez Ayala for reporting the problem and helping to
debug it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some 5701 devices with older bootcode, the LED configuration bits in
SRAM may be invalid with value zero. The fix is to check for invalid
bits (0) and default to PHY 1 mode. Incorrect LED mode will lead to
error in programming the PHY.
Thanks to Grant Grundler for debugging the problem.
>From Grant:
| In May, 2004, tg3 v3.4 changed how MAC_LED_CTRL (0x40c) was getting
| programmed and how to determine what to program into LED_CTRL. The new
| code trusted NIC_SRAM_DATA_CFG (0x00000b58) to indicate what to write
| to LED_CTRL and MII EXT_CTRL registers. On "IOX Core Lan", SRAM was
| saying MODE_MAC (0x0) and that doesn't work.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o use a semaphore instead of an opencoded and racy lock
o move locking out of shaper_kick and into the callers - most just
released the lock before calling shaper_kick
o remove in_interrupt() tests. from ->close we can always block, from
->hard_start_xmit and timer context never
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The times when tricky goto's produced better codes are long gone.
This patch should express the same in a better way.
(Also fixes the final gcc-4.0 x86 compile error)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add tg3_nvram_lock() and tg3_nvram_unlock() calls around tg3_halt_cpu().
It is possible that the bootcode may be loading code from nvram during
this call and stopping the cpu without getting the lock may cause
uncompleted nvram data to be left in the nvram data register. Subsequent
calls to read/write nvram data will fail.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test uses the previously added tg3_test_interrupt() to perform the
test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
