This patch contains
- new tuning code for the tda827xa silicon tuner.
- controls the preamplifier of some boards with this tuner.
- support for the Philips Tiger S hybrid DVB-T reference design.
- reworked the saa7134-dvb modulue to get rid of most of the
small board specific functions.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These entries mainly are to support configurations of the tda827x
silicon tuner with a preamplifier.
The values can be set throgh the attach inform or through
the extended TUNER_SET_TYPE_ADDR client call. The function pointer
will only be updated if the parameter is not NULL.
Since a typecast is necessary to set the pointer, i added a typedef for
this pointer (tuner_gpio_func_t) in tuner.h
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This function allows to set, clear and tristate the GPIO ports.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are the following changes:
- separate configuration of IF and GPIOs.
- set GPIOs before firmware load. This helps to avoid I2C address
collisions.
- if desired invert GPIOs at sleep (automatic return to analog mode of card).
- added 3 tuner configuration bytes to config stuct.
- added i2c gate address to config struct.
- moved _state struct declaration to header file to make it accessible
on board layer.
- added "conf_probed" to the state struct to allow i.e. probing for correct
tuner version.
- changed firmware load mechanism to always:
+ check if already loaded
+ try to boot from eeprom
+ try downlad from host
- corrected name of tda10046 firmware image (backward compatible).
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx23415 adds some extra features that this DVB decoding API did
not support. This API has been expanded to support the required
features. Both source and binary backwards compatibility is kept
intact by these changes. So existing applications are not affected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOC_G_CHIP_IDENT improves debugging of card problems: it can be
used to detect which chips are on the board and based on that information
selected register dumps can be made, making it easy to debug complicated
media chips containing tens or hundreds of registers.
This ioctl replaces the internal VIDIOC_INT_G_CHIP_IDENT ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for loading cx88-dvb and cx88-blackbird
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
added support for deferred module requesting to cx88
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added VIDIOC_INT_G_STD_OUTPUT and VIDIOC_INT_S_STD_OUTPUT to allow drivers
to set the TV standard for video output separately from the video capture.
This is needed for cx23415 support where the decoder is separate from the
encoder and can have a different TV standard.
Modified the saa7127 module to listen to VIDIOC_INT_G/S_STD_OUTPUT instead
of VIDIOC_G/S_STD.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add V4L2_BUF_TYPE_VIDEO_OUTPUT_OVERLAY support.
Also add support for local and global alpha overlays.
Add new field enums V4L2_FIELD_INTERLACED_TB and V4L2_FIELD_INTERLACED_BT.
These changes are needed to support the ivtv On Screen Display features.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added V4L2_CID_MPEG_AUDIO_MUTE, V4L2_CID_MPEG_VIDEO_MUTE and
V4L2_CID_MPEG_CX2341X_STREAM_INSERT_NAV_PACKETS controls together with
their implementation in the cx2341x module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a V4L2 driver giving support for USB webcams based on the
zr364xx chipsets.
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DVB USB remotes do not support changing keycode maps but set
input_dev->keycodesize and input_dev->keycodemax without setting
input_dev->keycode. This causes kernel oops when user tries to
look up (or change) current keymap.
While the proper fix would be to make remotes handle keymap changes
we'll just remove keycodemax and keycodesize initialization so
EVIOCGKEYCODE and EVIOCSKEYCODE will simply return -EINVAL.
http://bugzilla.kernel.org/show_bug.cgi?id=8312
Signed-off-by: olaf.kirch@oracle.com
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ADEF bits in the TSCR register have different meanings in read and
write mode. For this reason ADEF has to be reset on every
read-modify-write operation.
This patch introduces a special write function for this register, which
takes care of it.
Thanks to Holger Magnussen for pointing my nose at this problem.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Setting the message length to zero means to send one byte, so you need a
subtraction instead of an addition.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After freeing a block there should be no reference to this block.
Signed-off-by: Thomas Viehweger <Thomas.Viehweger@marconi.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Returning -1 causes the probe to stop, but it should just continue
instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix several instances of dvb-core functions using mutex_lock_interruptible
and returning -ERESTARTSYS where the calling function will either never
retry or never check the return value.
These cause a race condition with dvb_dmxdev_filter_free and
dvb_dvr_release, both of which are filesystem release functions whose
return value is ignored and will never be retried. When this happens it
becomes impossible to open dvr0 again (-EBUSY) since it has not been
released properly.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All the radio drivers need video_dev, but they were depending on
VIDEO_DEV!=n. That meant that one could try to compile the driver into
the kernel when VIDEO_DEV=m, which will not work. If video_dev is a
module, then the radio drivers must be modules too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After dvb tuner refactoring, the pllbuff has been altered such that the pll
address is now stored in buf[0]. Instead of sending buf to set_pll_input,
we should send buf+1.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Ivan Andrewjeski <ivan@fiero-gt.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the cx88-blackbird driver to be able to use the new cx23416
firmware image released by Hauppauge Computer Works, while retaining
compatibility with the older firmware images.
cx2341x firmware can be downloaded at: http://dl.ivtvdriver.org/ivtv/firmware/
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move VIDIOC_DBG_S/G_REGISTER from the internal ioctl list to the
public ioctls, but mark it as experimental for now.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for starting, stopping, pausing and resuming an MPEG (or similar
compressed stream) encoder.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VIDIOC_G_ENC_INDEX ioctl can obtain the MPEG index from an MPEG
encoder.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Without this patch, the device will not be detected after firmware download
on big endian systems.
Signed-off-by: Jin-Bong lee <jinbong.lee@samsung.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following warning:
drivers/media/video/cafe_ccic.c: In function `cafe_vidioc_reqbufs':
drivers/media/video/cafe_ccic.c:1197: warning: 'ret' might be used uninitialized in this function
Probably not a real bug, but the warning can be avoided easily.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb-pll normally opens the i2c gate before attempting to communicate with
the pll, but the code for this device is not using dvb-pll. This should
be cleaned up in the future, but for now, just open the i2c gate at the
appropriate place in order to fix this driver bug.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The chip matching in struct v4l2_register for VIDIOC_DBG_G/S_REGISTER
was rather primitive. It could not be extended to other busses besides
i2c and it lacked a way to.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to changes in the i2c handling in 2.6.20 this cx25840 bug surfaced,
causing the firmware load to fail for the ivtv driver. The correct
sequence is to first attach the i2c client, then use the client's
device to load the firmware.
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In function 'qt1010_init':
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The result of copy_to_user was not used, so the compiler complained
now a warning will be issued if copy_to_user fails.
Signed-off-by: Marcel Siegert <mws@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Enable BER/UNC counting for the stv0297 frontend.
The idea for this patch comes from stv0297_cs.c.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Commit 00c4cc6751 Oliver Endriss changed
the budget-ci driver to use interrupt mode for i2c transfers.
This also meant that a new bunch of IR bytes that were previously lost
are now received, which allowed me to better understand how the MSP430
chip works. Unfortunately it also means that the current driver gets
some assumptions wrong and might generate double keypresses for one IR
command.
The attached patch fixes this by throwing away the repeat bytes and by
associating the correct command and device bytes.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Arjan van de Ven <arjan@infradead.org> reported an illegal re-usage of
the fileoperations struct if more than one dvb device (e.g. frontend) is
present.
This patch fixes this issue.
It allocates a new fileoperations struct each time a device is
registered and copies the default template fileops.
Signed-off-by: Marcel Siegert <mws@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The work item function is dvb_usb_read_remote_control():
INIT_WORK(&d->rc_query_work, dvb_usb_read_remote_control, d);
and the last piece of work it does is:
schedule_delayed_work(&d->rc_query_work,msecs_to_jiffies(d->props.rc_interval));
Hence you need to call "cancel_rearming_delayed_work()" and not
"cancel_delayed_work()", correct? I certainly haven't seen this oops
reoccur since I applied this patch.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
