When STA role is coexisting with other sessions(P2P, SAP or IBSS),
WAPI encryption mode is not allowed.
Add a new API to check if the connection/start request should
be rejected when:
1) A STA with WAPI encryption is to be connected while there
is at least one concurrent session already running.
2) A new session is to be started while there is already a STA
connection with WAPI encryption enabled.
Change-Id: Idf0d346138eeda339254535f1f7131fda4a5086a
CRs-Fixed: 2290549
The driver currently changes the hw_mode based upon
the first candidate found in the scan list, and tries
to connect to it. It may happen that the connection
fails, and the STA then tries to connect to the AP
on same channel as the concurrent adapter.
It would result in hw_mode = DBS, as it is not
updated after connection success/failure.
Also if the first AP channel is in same band as that
of concurrent adapter, and the connection fails,
and the STA tries to connect to an AP in a different
band, this too is not allowed as hw_mode is not DBS
Fix is to change the hw_mode based upon the scan list.
If the driver finds any scan result which may lead to
DBS connection, the hw_mode should be set to DBS.
Once the connection is done or failed, the driver
can check and update the hw_mode again.
Change-Id: I3c186f47dd5528f0af2598bb02c1b7e297d01548
CRs-Fixed: 2290760
Add ENABLE_DBS_CXN_AND_DISABLE_SIMULTANEOUS_SCAN option for the ini
gDualMacFeatureDisable. This is to enable DBS support for the
connection and disable simultaneous scan from upper layer. But DBS
scan remains enabled in FW.
Change-Id: Ic280de2cc63a3775c0d9dd61985ff89df58a4a89
CRs-Fixed: 2291935
Do not invoke get_pcl when calculating weightage of channels sent to FW
as part of set_pcl WMI command.
Change-Id: I62b39aaf0943cf10deab380d8030d1ef08fbbcb3
CRs-Fixed: 2287649
Firmware needs HW MODE ID not list index.
Use HW mode ID to set HW MODE WMI command.
Change-Id: I12f9d83daee1c99706c345d85f03781257b492bf
CRs-Fixed: 2256175
Extract/Save the Hw mode ID and Mac0 band info
to hw mode list.
This helps to identify the 2x2 5G + 1x1 2G and
2x2 2G + 1x1 5G.
Change-Id: I0682337b1a80c1b502c3307e0847aaa99479d2d3
CRs-Fixed: 2256152
Standalone SAP is not allowed on lte-coex channel if STA+SAP SCC
enabled on lte-coex channel. So move the SAP to a safe channel
once STA disconnected.
Change-Id: I00682f5bbb3da772e3e26ccd8d08183be28cc9ec
CRs-Fixed: 2265263
Standalone SAP is not allowed on DFS channel if STA+SAP SCC enabled
on DFS channel. So move the SAP to a non DFS channel as soon as STA
gets disconnect.
CRs-Fixed: 2269249
Change-Id: I27d018739f53997641a7113cfc7c844e02bd7e29
If STA+SAP is doing SCC & g_sta_sap_scc_on_lte_coex_chan is set,
don't move SAP to a different channel when LTE channel avoidance
event comes.
Change-Id: I3dfdbb6d59769a8ff9b3b2e6d828feee94630569
CRs-Fixed: 2268993
When sta+sap scc enabled on dfs channel then SAP cannot operate on
DFS channel in standalone mode. If STA+SAP are operating in SCC mode
on a DFS channel and STA gets disconnected from reference AP then driver
schedules a workqueue to move the SAP from DFS channel to user configured
channel. At this time if STA again connects to reference AP within few ms
then driver again schedules one more workqueue to move the SAP to STA's
channel. Sometimes the second workqueue may fail to switch the channel
if first one is not yet completed. So added event variable to schedule
second workqueue only when first one is complete.
CRs-Fixed: 2267005
Change-Id: Ia6ce4b6264c35f6d2c809e2a3f65f535e930874e
If MCC to SCC switch is enabled, SAP is active and CSA
received for STA interface, then ignore the CSA if channel
is DFS/disabled.
CRs-Fixed: 2263037
Change-Id: I98b8d957766358ea86cc9f50339725cf4bf0038b
When STA's join req times out on current BSS, SME issues next BSS
internally without checking HW mode for new channel
For example, STA tries to connect SSID="abc",
BSSID="a1:a2:a3:a4:a5:a6", channel=36 and lets say it fails. It
should try few more times to same BSSID and after that it will try
next bss. Lets say next BSS it found has, SSID="abc",
BSSID="b1:b2:b3:b4:b5:b6", channel=1 then it needs to check whether
hardware mode change is required for channel=1. If driver fails in
checking hardware mode then following check will prevent the bad
situation.
CRs-Fixed: 2261129
Change-Id: Ie31ac5b8b90c6e63122148647ad333fccfbf9dbf
Currently, PCL list is populated without checking channel select logic
ini. Check for channel select logic ini before selecting the second
connection pcl table.
Change-Id: I5a64d4ff43a7dcc2c70eac75b51d5f87de2903bb
CRs-FIxed: 2237403
When Force SCC and STA+SAP SCC on LTE coex channel are enabled:
1. When STA on LTE coex channel, start SAP, select STA
channel.
2. When SAP on, connect STA on LTE coex channel, then switch
SAP channel to STA channel.
Change-Id: I7864e0ab2655c3bee95154ea4dedfb60fe8689e4
CRs-Fixed: 2261226
Current lithim_dp flow pool created in wma_vdev_start, wma_vdev_start
is called for same vdev multiple times for vdev. This leads to creation
of multiple flow pools for each vdev. Instead create from policy_manager
when session become active.
Register flow pool create/delete callbacks with policy manager.
So that lithium_dp vdev flow pools are created/deleted when vdev
become active/not-active.
Change-Id: Iaf6aaece47c79c7e6f7745feaee35a6bc5cd1297
CRs-Fixed: 2231601
Check capability of dbs, mcc and scc on single band when enable
AP+AP, then same driver code can support different chip and
firmware.
Add wmi_service_dual_beacon_on_single_mac_(mcc/scc)_support
Change-Id: I505747122504b2a89813e7bdfcd27dc07539f39e
CRs-Fixed: 2214237
While calling sme_pdev_set_pcl() API, driver is passing the argument
by value. The size of the argument is 280 bytes which is not good
design.
Pass the argument by reference instead of passing it by value to make
design simple.
CRs-Fixed: 2238293
Change-Id: I92849fb125fe864c1c7c7977bce392a7bcfe4121
Previously change "qcacmn: Use enum QDF_OPMODE", Change-Id
Ic6f663dac11a100f168b2626c7c0fbcaccbfca4f, replaced all instances of
tQDF_ADAPTER_MODE to QDF_OPMODE in the qca-wifi-host-cmn
project. However since tQDF_ADAPTER_MODE was originally defined in a
common project, and not all references to it could be immediately
removed, a legacy definition was left with the expectation that it
would be removed when all references to it had been
updated. Unfortunately new instances of using tQDF_ADAPTER_MODE have
been subsequently added to the project, so replace them with
QDF_OPMODE.
Change-Id: I71cead84151cc0411f7cc5cc13a87a281e7502c0
CRs-Fixed: 2245249
Remove duplicate structs wmi_dual_mac_config and sir_dual_mac_config
and use policy_mgr_dual_mac_config.
Change-Id: I6da6539f519ec46ee274ba3f3ae042e5fd9c25d2
CRs-Fixed: 2191031
Add API to get NAPI instance from NAPI ID. Handle to NAPI is required
for Rx processing via GRO.
Change-Id: I15535827a03953231670d4138235c4876b16e045
CRs-Fixed: 2062180
Issue is under AP-AP MCC config, mcc event is not sent from wlan
to IPA driver. mcc mode is decided with the help of connection
table. But for AP mode, mcc mode is checked and updated before
connection table is updated by adding the SAP vdev entry.
Fix is to make ipa mcc mode check and notification when connection
table is updated.
Change-Id: I1ba3fcb874b014f05cebd8af90530b9aa54980a2
CRs-Fixed: 2214351
Add ENABLE_DBS_CXN_AND_DISABLE_DBS_SCAN option for the ini
gDualMacFeatureDisable. To enable DBS support for the
connection and disable DBS support for the scan.
Change-Id: I05c613467195fffac98e79b7e4a2991471ac1d80
CRs-Fixed: 2207820
Add support for HW mode info vendor command which sends
mac id, band, interface id and frequency information for
each MAC provided by driver to userspace.
Change-Id: If1112d29b8781cf5ba0480c84feeb772142f2c0e
CRs-Fixed: 2185559
Set hw mode to DBS or single MAC for STA+STA and STA+P2P
concurrencies based on channel_select_logic_conc ini.
Change-Id: I46ba4d5cd8f5cda71d0c00be2b612bc851eb5ba4
CRs-Fixed: 2189848
Add ini to select DBS or inter-band MCC channel selection logic
for STA+STA and STA+P2P connections.
Change-Id: I7cfde9592ec210b0a8c812171d2bc6f005e17fb2
CRs-Fixed: 2189845
If force SCC is enabled and there is a STA connection, trim the
ACS channel list on the band on which STA connection is present.
Change-Id: Ibd580a7afdcdfc5fb4398ada547565e229d59c70
CRs-Fixed: 2193720
For the AP+AP SCC LTE-Coex case, when channel avoidance event
is reported, the channel switch request for SAP will be blocked
by policy manager if the target channel is different with the
operating channel of the existing SAP due to the SCC policy.
Need to update the logic to give higher priority to the channel
avoidance request.
Change-Id: Ie42bab50c1fa92e4e8df9f1b0ce8b8f4f09551b5
CRs-Fixed: 2176250
Stop the opportunistic timer & take action to keep HW mode in sync
when hdd stop happens.
Change-Id: Id34adb579987605831d2c7c4e22c2d76fe7d25dd
CRs-Fixed: 2165109
Set passive dwell time to 28msecs for active
scan when bt a2dp is enabled and hw is not dbs
capable and when sta is connected on 2G band.
Change-Id: I44f2e3d98f2d7ddc52e4902ba989131c256da4ef
CRs-Fixed: 2160963
Allow SAP to come up on DFS channel in STA+SAP concurrency mode
only when g_sta_sap_scc_on_dfs_chan enabled in ini file and also
disable chan_switch_hostapd_rate_enabled when force SCC is enabled.
CRs-Fixed: 2147032
Change-Id: Id1333a49d0538eb4ccfaf3c8498e9ca06671de02
Typically set hw mode & Nss update happens at the same time. Since the
order of these 2 actions may not be same always, make them independent
of each other.
Change-Id: I652ad08e16680991535e0f064c7b5996f4f58792
CRs-Fixed: 2144977
Change "qcacmn: Rename enum tQDF_ADAPTER_MODE" (qca-wifi-host-cmn
Change-Id I20f1b6d1a0ab4b8fe6a85cefdff96a49e2f4652c) renamed enum
tQDF_ADAPTER_MODE to QDF_OPMODE. Update all references to use the
new name.
Change-Id: Ic6f663dac11a100f168b2626c7c0fbcaccbfca4f
CRs-Fixed: 2141061
Stop the opportunistic timer & take action if needed when hdd stop
happens. Also, take action when set_hw_mode request to FW times out.
Change-Id: I32f1e38e93a5805e0d85b800cc4e070cd6f79669
CRs-Fixed: 2133388
If force SCC is set and SAP is active then all DFS/disabled
channels in PCL should have 0 weight to avoid the STA roaming
to these channels.
Change-Id: I4519c29477c5108f5131b7caa806505b69efea8b
CRs-Fixed: 2135750
SAP Rx TPUT is bounded by host network stack, which is running in the
context of IPA work-queue, when IPA offload data path enabled.
However RPS shouldn't enabled for legacy Rx data path, where NAPI is
enabled. So, we dynamically enable RPS for SAP interface when the vdev
comes up and IPA was enabled only.
Send RPS enable indication to CNSS daemon to enable RPS only when SAP
interface comes up and disable RPS when SAP interface is closed.
Change-Id: Ia669b2c3ae814d0577f5226d8acbf026740ad760
CRs-Fixed: 2129520
LRO rx jumbo packets cannot be forwarded to other vdev and kernel drops
them with warning message:
"skbuff: wlan0: received packets cannot be forwarded while LRO is enabled"
So disable LRO capability during concurrency.
Change-Id: Ib35e1ee5f9c18a846e21ce1eb293e12e17761fa8
CRs-Fixed: 1092193
Refactor the code to dynamically change the conc_system_pref.
Whenever user changes conc_system_pref from application,
driver is overwriting the conc_system_pref which is getting
populated from ini file. Once it is overwritten there is no way
to get the configured value for this setting. So add a new
variable to hold the value of conc_system_pref without disturbing
default value read from ini file.
CRs-Fixed: 2082073
Change-Id: Icfb245c7a8872885332ec222780c911d08521d46
If SAP is up & STA is coming up next(or vice versa) on a different
channel causing MCC, move SAP to cause SCC or DBS. This logic is
enabled only if gWlanMccToSccSwitchMode is set to
QDF_MCC_TO_SCC_SWITCH_FORCE_WITHOUT_DISCONNECTION or
QDF_MCC_TO_SCC_SWITCH_WITH_FAVORITE_CHANNEL.
Change-Id: I16615d828a285762133ee3533339320ef119b3d3
CRs-Fixed: 2063060
If STA is up & SAP is comings up on a ACS derived channel causing MCC,
move SAP to the other band if DBS is supported. This logic is enabled
only if gWlanMccToSccSwitchMode is set to
QDF_MCC_TO_SCC_SWITCH_FORCE_WITHOUT_DISCONNECTION.
Change-Id: I48d809f83921292f51ca1735bff4c4d6dd339975
CRs-Fixed: 2063060
