- Restore in s2io_reset, the mac address assigned during s2io_open.
Earlier, it was getting overwritten to the factory default (read from the
eeprom) and subsequently dropping received frames.
- Fixed the typo in calling rtnl_unlock in s2io_set_link function.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Enhanced Statistics are supported only for Xframe II (Herculas) card. Add
condition check such Enhanced statistics will included only in the case of
Xframe II card.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Turning off LED for LINK_DOWN notification
- Return from rxd_owner_bit_reset function if call to set_rxd_buffer_pointer
fails with ENOMEM
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added code to not to strip vlan tag when driver is in promiscuous mode
- Added module loadable parameter 'vlan_tag_strip" through which user can
enable or disable vlan stripping irrespective of mode
( promiscuous or non-promiscuous ).
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Optimized delay to wait for command completion so as to reduce the
initialization wait time.
- Disable differentiated services steering. By default RMAC is configured to
steer traffic with certain DS codes to other queues. Driver must initialize
the DS memory to 0 to make sure that DS steering will not be used by default.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added debug statements to print a debug message if the MSI/MSI-X vector (or)
data is zero.
- This patch removes the code that will enable NAPI for the case of single
ring and MSI-X / MSI case. There are some issue in the enabling NAPI with
MSI/MSI-X. So we are turning off NAPI in the case of MSI/MSI-X.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To reproduce this panic consistently, we run an intensive network
application like 'netperf'. After waiting for a couple of seconds,
you will see a stack trace and a kernel panic where we are calling
pci_unmap_single() in ql_poll().
Changes:
1) Check the flags on the Response MAC IO Control block to check for
errors
2) Ensure that if we are on the 4022 we only use one segment
3) Before, we were reading the memory mapped producer index register
everytime we iterated in the loop when clearing the queue. We should
only be iterating to a known point, not as the producer index
is being updated.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To Reproduce the Problem:
To reproduce this panic consistently, we run an intensive network
application like 'netperf' and then switch to a different console.
After waiting for a couple of seconds, you will see a tx reset has occured.
Reason:
We enable interrupts even if we were not running.
Solution:
Now we will enable interrupts only after we are ready to give up the poll
routine.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_map_single() could fail. We need to properly check the return
code from pci_map_single(). If we can not properly map this address,
then we should cleanup and return the proper return code.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The scatter/gather lists were not being build correctly. When
large frames spanned several buffers the chip would panic.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This change removes use of constants for rx buffer queue size
and instead calculates the queue length based on what he MTU
is set to.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This network device driver shares the same hardware as the qla4xxx
iSCSI driver. Changing the MTU via the device interface will
cause qla4xxx to crash as there is no way to make notification.
Users wishing to change the MTU must do so using an iSCSI
utility such as Qlogic SanSurfer. This forces the user to
unload/reload this network device driver after the MTU
value has been changed in flash.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1) Fix deadlock issue when in QL_RESET_ACTIVE state and traversing
through the Link State Machine
2) Fix deadlock issue when ethtool would call ql_get_settings()
3) Fix deadlock issue when adaptor is ifup'ed but adaptor fails to initialize
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We do not need to zero out the 64 byte MAC request I/O control block.
By zeroing out the control block and setting it to proper fields is
redundant work. This is because in the qla3xxx_send() function we will
already set the proper fields in this structure. The unused fields are
not looked at by the hardware and do not need to be zeroed out.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The return code was not properly set when when allocating memory or mapping
memory failed. Depending on the stack, the return code would sometimes
return 0, which indicates everything was ok, when in fact there was an error.
This would cause trouble when the module was removed. Now, we will pass
back the proper return code when an error occurs during the PCI probe.
Signed-off-by: Benjamin Li <benjamin.li@qlogic.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver contains this little piece of candy:
#if defined(CONFIG_DMA_NONCOHERENT) || defined(CONFIG_NOT_COHERENT_CACHE)
#define ETH_DMA_ALIGN L1_CACHE_BYTES
#else
#define ETH_DMA_ALIGN 8
#endif
Any reason why we're not using dma_get_cache_alignment() instead?
Ralf
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ucc_geth_probe() to use function of_get_mac_address() to obtain the MAC
address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It looks like the skge driver inherited another bug from the sk98lin code.
If I send from 1000mbit port to a machine on 100mbit port, the switch should
be doing hardware flow control, but no pause frames show up in the statistics.
This is the analog of the recent sky2 fixes. The device needs to listen
for multicast pause frames and then not discard them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Work around a bug which occurs when adopting firmware versions
1.4.4 though 1.4.11 where broadcasts are filtered as if they
were multicasts.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple threads performing a transmit can race into
the spidernet tx ring cleanup code. This puts the
relevant check under a lock.
Signed-off-by: Linas Vepstas <lins@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It appears that under certain circumstances, a race will result
in a double-free of an skb. This patch null's out the skb pointer
upon the skb free, avoiding the inadvertent deref of bogus data.
The next patch fixes the actual race.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch separates the hardware descriptor state from the
driver descriptor state, per (old) suggestion from Ben Herrenschmidt.
This compiles and boots and seems to work.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This moves the medium variable into the spidernet card structure.
It renames the GMII_ variables to BCM54XX specific ones.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patches removes logging for SPIDER_NET_GTMFLLINT interrupts.
Since the interrupts are not irregular, and they happen frequently
when using 100Mbps network switches.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds or changes some HW specific settings for spider_net on
Celleb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves calling init_firmware() from spider_net_probe() to
spider_net_open() so as to use the driver by built-in.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add auto negotiation support for Celleb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As of 2.6.20-git4, the spider_net driver does not compile.
This appears to be due to some archaic usage involving kobjects.
It also fixes a nasty double-free during ifdown of the interface.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This version moves the medium variable to the card specific structure and
changes the GMII_* to BCM54XX_* #defines.
This patch adds improved version of enable_fiber for both the 5421 and
the 5461 phy. It is now possible to specify with these wether you want
autonegotiation or not. This is needed for bladecenter switches where
some expect autonegotiation and some dont seem to like this at all.
Depending on this flag it sets phy->autoneg accordingly for the fiber mode.
More importantly it implements proper read_link and poll_link functions
for both phys which can handle both copper and fiber mode by determining
the medium first and then branching to the required functions. For fiber
they all work fine, for copper they are not tested but return the result
of the genmii_* function anyway which is supposed to work.
The patch moves the genmii_* functions around to avoid foreward declarations.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes checksum offload feature in mcp65 chipsets as they
are not supported in hw.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There seems to be an issue when both MSI-X is enabled and NAPI is
configured. This patch disables MSI-X until the issue is root caused.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The napi poll routine was missing the call to the optimized rx process
routine. This patch adds the missing call for the optimized path.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* clear_page() use is wrong. We might have multiple pages.
Use memset() instead.
* Call pci_unregister_driver() in module exit.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
1. Add race condition check after netif_stop_queue(). tg3_tx() runs
without netif_tx_lock and can race with tg3_start_xmit_dma_bug() ->
tg3_tso_bug().
2. Firmware TSO in 5703/5704/5705 also have the same TSO limitation,
i.e. they cannot handle TSO headers bigger than 80 bytes. Rename
TG3_FL2_HW_TSO_1_BUG to TG3_FL2_TSO_BUG and set this flag on
these chips as well.
3. Update version to 3.74.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d2ed16356f.
As Thomas Gleixner reports:
"e1000 is not working anymore. ifup fails permanentely.
ADDRCONF(NETDEV_UP): eth0: link is not ready
nothing else"
The broken commit was identified with "git bisect".
Auke Kok says:
"I think we need to drop this now. The report that says that this
*fixes* something might have been on regular interrupts only. I
currently suspect that it breaks all MSI interrupts, which would make
sense if I look a the code. Very bad indeed."
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (21 commits)
natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
natsemi: Add support for using MII port with no PHY
skge: race with workq and RTNL
Replace local random function with random32()
s2io: RTNL and flush_scheduled_work deadlock
8139too: RTNL and flush_scheduled_work deadlock
sis190: RTNL and flush_scheduled_work deadlock
r8169: RTNL and flush_scheduled_work deadlock
[PATCH] ieee80211softmac: Fix setting of initial transmit rates
[PATCH] bcm43xx: OFDM fix for rev 1 cards
[PATCH] bcm43xx: Fix for 4311 and 02/07/07 specification changes
[PATCH] prism54: correct assignment of DOT1XENABLE in WE-19 codepaths
[PATCH] zd1211rw: Readd zd_addr_t cast
[PATCH] bcm43xx: Fix for oops on resume
[PATCH] bcm43xx: Ignore ampdu status reports
[PATCH] wavelan: Use ARRAY_SIZE macro when appropriate
[PATCH] hostap: Use ARRAY_SIZE macro when appropriate
[PATCH] misc-wireless: Use ARRAY_SIZE macro when appropriate
[PATCH] ipw2100: Use ARRAY_SIZE macro when appropriate
[PATCH] bcm43xx: Janitorial change - remove two unused variables
...
Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware. After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mackerras <paulus@samba.org>
Aculab E1/T1 PMXc cPCI carrier card cards present a natsemi on the cPCI
bus with an oversized EEPROM using a direct MII<->MII connection with no
PHY. This patch adds a new device table entry supporting these cards.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch provides code paths which allow the natsemi driver to use the
external MII port on the chip but ignore any PHYs that may be attached to it.
The link state will be left as it was when the driver started and can be
configured via ethtool. Any PHYs that are present can be accessed via the MII
ioctl()s.
This is useful for systems where the device is connected without a PHY
or where either information or actions outside the scope of the driver
are required in order to use the PHYs.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a workqueue function that needs RTNL is running when skge_down
is called then a deadlock is possible. Fix by only clearing the timer,
and handling the flush_scheduled_work on removal. This work queue is only
ever used for the old fiber based boards.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mantra: don't use flush_scheduled_work with RTNL held.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Your usual dont-flush_scheduled_work-with-RTNL-held stuff.
It is a bit different here since the thread runs permanently
or is only occasionally kicked for recovery depending on the
hardware revision.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
flush_scheduled_work() in net_device->close has a slight tendency
to deadlock with tasks on the workqueue that hold RTNL.
rtl8169_close/down simply need the recovery tasks to not meddle
with the hardware while the device is going down.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
sk98lin is scheduled for removal in July 2007. This patch makes the
deprecation more obvious in the configuration interface. FWIW, Gentoo have
been shipping a patch very similar to this for a long time.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Comtrol Hostess SV-11 driver uses features from INET but doesn't depend on it.
The simple solution is to make it depend on INET as happens for the sealevel
driver.
Fixes bug #7930.
Signed-Off-By: Baruch Even <baruch@ev-en.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Start link negotiation in the open method. Previously it was started
on driver initialialization and shutdown on close so an ifdown would
have results in closing negotiation for good.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Nag message about planned sk98lin removal.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The b44 Enet control disable bit may take longer to clear on some
systems, so the loop count is increased with this patch. Functionality
is not compromised, but a debug message can be seen when the bit is not
cleared within the count value.
Thanks to Vasileios Lourdas who reported the problem.
Signed-off by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
By reading the MAC status register we can detect whether the MAC has
seen the PHY see link. This allows us to show the link properties before
the device is up in ethtool.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that 2.6.19 provides a proper implementation that saves MSI, PCI-E
config space, we can have the e1000 driver use those instead of it's
custom implementation.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The modifications and bug fixes noted below were done by Realtime Control
Works and Contemporary Control Systems, Inc, Jan 2005. They were
incorporated into the 2.6 kernel by Jeff Morrow of Sierra Analytics, Feb
2007. <jmorrow@massspec.com>
The changes have been tested on a Contemporary Controls PCI20U-4000.
Summary of changes:
Arc-rawmode.c:
rx():
- Fixed error in received packet lengths; 256 byte packets were
being received as 257 bytes packets.
prepare_tx():
- Fixed error in transmit length calcs; 257 byte packets were being
transmitted as 260 byte packets.
com20020.c:
com20020_check():
- We now load the SETUP2 register if the 'clockm' parameter is
non-zero, instead of checking for ARC_CAN_10MBIT. The user is
now responsible for whether or not SETUP2 is loaded. If the
clock multiplier is non-zero, this means that the user wants a
baud rate greater than 2.5Mbps. This is not possible unless the
SETUP2 register is present (COM20020D, or COM20022). So, we're
relying on the user to be smart about what kind of chip he's
dealing with...
com20020-pci.c
- Added several entries to com20020pci_id_table[].
Signed-off-by: Jeff Morrow <jmorrow@massspec.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the experimental tag for the pcnet32 NAPI implementation.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove spin_lock_irqsave() around mii_ethtool_gset, mii_ethtool_sset
and generic_mii_ioctl. These are unnecessary and harmful because
the mii calls may call back into the mdio functions, which may sleep.
Pointed out by David Brownell.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't drop oversize frame it might be a VLAN (untagged).
Use different counter for fifo overrun vs fifo error.
Print error on fifo overrrun.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit timeout code could hang, and it would not clear out
problems if the hardware was stuck. Change the code to effectively do
a device down/up similar to the suspend/resume code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon-FE chip doesn't do gigabit and has a differen PHY internally.
On this chip, phy status register doesn't properly reflect the result
of flow control negotiation. To workaround the problem and avoid having
to have so much chip dependent code; compute the result of flow control
by looking at the local and remote advertised bits.
Signed-off-by: Stephen Hemmminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resetting the pause bits on shutdown is not necessary.
The code was inherited from the vendor driver, and it is currently #ifdef'd
out there as well.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't mark pause frames as errors. This problem caused transmitter not
to pause and would effectively take out a gigabit switch because the
it can't handle overrun.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix copyrights in the cxgb3 driver.
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was hardly necessary to repeat most of the code from gfar_error() in
gfar_interrupt(), especially having some inconsistencies between the two.
So, make the gfar_interrupt() just call gfar_error(), and not acknowledge
the interrupts itself as gfar_{receive/transmit/error}() do it anyway.
While at it, also clarify/cleanup debug messages in gfar_error()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert pci_module_init() to pci_register_driver().
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add device id for the Attansic L1 chip to pci_ids.h, then use it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unused define from atl1_main.c.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some Asus motherboards containing the L1 NIC, the MAC address is
written by the BIOS directly to the MAC register during POST, and is
not stored in eeprom. If we don't succeed in fetching the MAC address
from eeprom or spi, try reading it directly from the MAC register.
Suggested by Xiong Huang.
And do some cleanup while we've got the hood up...
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
An ioread32 statement reads the wrong address. Fix it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The atl1 driver doesn't need NET_PCI. Remove it from Kconfig.
Noticed by Chad Sprouse.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes include:
* New support for 88e1145
* New support for 88e111s
* Fixing 88e1101 driver to not match non-88e1101 PHYs
* Increases in feature support across Marvell PHY product line
* Fixes a bunch of whitespace issues found by Lindent
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Nearly all of the writes to the bcm43xx internal lookup tables (ilt)
involve 16-bit quantities. Accordingly, the ilt_write routine was
coded to pass a u16 value. For one early GPHY chip, 32-bit quantities
are needed. For those writes, the value was clipped to 16 bits. This
patch adds an ilt_write32 routine that receives a 32-bit quantity
and writes it to the appropriate locations.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The specifications for the bcm43xx driver have been modified. This
patch incorporates these changes in the code, which results in the
BCM4311 and BCM4312 working. The name of one of the PHY parameters,
previously known as "version", has been changed to "analog", short for
"analog core version" .
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct assignment of DOT1XENABLE in WE-19 codepaths.
RX_UNENCRYPTED_EAPOL = 1 really means setting DOT1XENABLE _off_, and
vice versa. The original WE-19 patch erroneously reversed that. This
patch fixes association with unencrypted and WEP networks when using
wpa_supplicant.
It also adds two missing break statements that, left out, could result
in incorrect card configuration.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Robert P.J. Day's recent commit ("getting rid of all casts of
k[cmz]alloc() calls") introduced a sparse warning for zd1211rw,
related to our type-checking of addresses.
zd_chip.c:116:15: warning: implicit cast to nocast type
This patch readds the type cast, it is correct.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a kernel oops on bcm43xx when resuming due to an overly
tight timeout loop.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If bcm43xx were to process an afterburner (ampdu) status response,
Linux would oops. The ampdu and intermediate status bits are properly
named.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A patch to use ARRAY_SIZE macro when appropriate.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A patch to use ARRAY_SIZE macro in the Host AP wireless driver.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A patch to use ARRAY_SIZE macro already defined in kernel.h for some
miscellaneous wireless drivers with no specific maintaners.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A patch to use ARRAY_SIZE macro already defined in kernel.h.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two bit-field values are extracted from the sprom data and never used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal. Fixup the remaining users in -mm.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Print the most useful information during tx timeout to help debug.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set DMA read watermark to 4 on 5703 in PCIX mode. This is needed to
prevent some tx timeouts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following problem:
http://bugzilla.kernel.org/show_bug.cgi?id=7969
The MSI state needs to be saved during suspend. PCI state saved
during tg3_init_one() does not contain valid MSI state because
MSI hasn't been enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert network devices to use struct device instead of class_device. Greg
missed this one in his cleanup path.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace a small number of expressions with a call to the "container_of()"
macro.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparse complains about differing types from prototype to
definition, so change the u32 to phy_interface_t:
drivers/net/phy/phy_device.c:140:19: error: symbol 'phy_connect' redeclared with different type (originally declared at include/linux/phy.h:362) - incompatible argument 5 (different signedness)
drivers/net/phy/phy_device.c:190:19: error: symbol 'phy_attach' redeclared with different type (originally declared at include/linux/phy.h:360) - incompatible argument 4 (different signedness)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Error recovery for QP errors: Reset QPs and dump error information
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A number of the calls in the initialization routines fail to check the returned value for
errors. This patch adds the necessary checks and logs any errors found when appropriate.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-tc:
[EISA] EISA registration with !CONFIG_EISA
[TC] pmagb-b-fb: Convert to the driver model
[TC] dec_esp: Driver model for the PMAZ-A
[TC] mips: pmag-ba-fb: Convert to the driver model
[TC] defxx: TURBOchannel support
[TC] TURBOchannel support for the DECstation
[TC] MIPS: TURBOchannel resources off-by-one fix
[TC] MIPS: TURBOchannel update to the driver model
On all targets that sucker boils down to memcpy_fromio(sbk->data, from, len).
The function name is highly misguiding (it _never_ does any checksums), the
last argument is just a noise and simply expanding the call to memcpy_fromio()
gives shorter and more readable source. For a lot of reasons it has almost
no remaining users, so it's better to just outright kill it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of changes to add TURBOchannel support to the defxx driver. As
at this point the EISA support in the driver has become the only not having
been converted to the driver model, I took the opportunity to convert it as
well. Plus support for MMIO in addition to PIO operation as TURBOchannel
requires it anyway.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (79 commits)
[IPX]: Fix NULL pointer dereference on ipx unload
[ATM]: atmarp.h needs to always include linux/types.h
[NET]: Fix net/socket.c warnings.
[NET]: cleanup sock_from_file()
[NET]: change layout of ehash table
[S390]: Add AF_IUCV socket support
[S390]: Adapt special message interface to new IUCV API
[S390]: Adapt netiucv driver to new IUCV API
[S390]: Adapt vmlogrdr driver to new IUCV API
[S390]: Adapt monreader driver to new IUCV API
[S390]: Rewrite of the IUCV base code, part 2
[S390]: Rewrite of the IUCV base code, part 1
[X.25]: Adds /proc/net/x25/forward to view active forwarded calls.
[X.25]: Adds /proc/sys/net/x25/x25_forward to control forwarding.
[X.25]: Add call forwarding
[XFRM]: xfrm_migrate() needs exporting to modules.
[PFKEYV2]: CONFIG_NET_KEY_MIGRATE option
[PFKEYV2]: Extension for dynamic update of endpoint address(es)
[XFRM]: CONFIG_XFRM_MIGRATE option
[XFRM]: User interface for handling XFRM_MSG_MIGRATE
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
MAINTAINERS: update DMFE and wireless drivers mailing list
ucc_geth: Add support to local-mac-address property
ucc_geth: Remove obsolete workaround of link speed change
cxgb3: sysfs attributes in -mm tree
Add Attansic L1 ethernet driver.
IEEE-1275 defines “local-mac-address” to be a standard
property name to specify preassigned network address.
This patch adds support for it.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The workaround used a long delay of 4s which caused problem
when two link-changes happens at the same time.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Wu Xiaochuan <xiao-chuan.wu@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the usage of sysfs attributes in cxgb3 for the -mm tree.
It is built against the driver commited in the -mm tree.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace kmalloc() + memset() pairs with the appropriate kzalloc() calls in
the bonding driver.
Signed-off-by: Joe Jin <lkmaillist@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
During an oprofile session of linux-2.6.20 on a dual opteron system, I noticed
an expensive divide was done in tg3_poll().
I am using gcc-4.1.1, so the following comment from drivers/net/tg3.c seems
over-optimistic :
/* Do not place this n-ring entries value into the tp struct itself,
* we really want to expose these constants to GCC so that modulo et
* al. operations are done with shifts and masks instead of with
* hw multiply/modulo instructions. Another solution would be to
* replace things like '% foo' with '& (foo - 1)'.
*/
#define TG3_RX_RCB_RING_SIZE(tp) \
((tp->tg3_flags2 & TG3_FLG2_5705_PLUS) ? 512 : 1024)
Assembly code before patch :
(oprofile results included)
6434 0.0088 :ffffffff803684b9: mov 0x6f0(%r15),%eax
587 8.0e-04 :ffffffff803684c0: and $0x40000,%eax
2170 0.0030 :ffffffff803684c5: cmp $0x1,%eax
:ffffffff803684c8: lea 0x1(%r13),%eax
:ffffffff803684cc: sbb %ecx,%ecx
2051 0.0028 :ffffffff803684ce: xor %edx,%edx
:ffffffff803684d0: and $0x200,%ecx
20 2.7e-05 :ffffffff803684d6: add $0x200,%ecx
1986 0.0027 :ffffffff803684dc: div %ecx
103427 0.1410 :ffffffff803684de: cmp %edx,0xffffffffffffff7c(%rbp)
Assembly code after the suggested patch :
ffffffff803684b9: mov 0x6f0(%r15),%eax
ffffffff803684c0: and $0x40000,%eax
ffffffff803684c5: cmp $0x1,%eax
ffffffff803684c8: sbb %eax,%eax
ffffffff803684ca: inc %r13d
ffffffff803684cd: and $0x200,%eax
ffffffff803684d2: add $0x1ff,%eax
ffffffff803684d7: and %eax,%r13d
ffffffff803684da: cmp %r13d,0xffffffffffffff7c(%rbp)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace kmalloc() + memset() pairs with the appropriate
kzalloc().
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc: (116 commits)
[POWERPC] Add export of vgacon_remap_base
[POWERPC] Remove bogus comment about page_is_ram
[POWERPC] windfarm: don't die on suspend thread signal
[POWERPC] Fix comment in kernel/irq.c
[POWERPC] ppc: Fix booke watchdog initialization
[POWERPC] PPC: Use ARRAY_SIZE macro when appropriate
[POWERPC] Use ARRAY_SIZE macro when appropriate
[POWERPC] Fix ppc64's writing to struct file_operations
[POWERPC] ppc: use syslog macro for the printk log level
[POWERPC] ppc: cs4218_tdm remove extra brace
[POWERPC] Add mpc52xx/lite5200 PCI support
[POWERPC] Only use H_BULK_REMOVE if the firmware supports it
[POWERPC] Fixup error handling when emulating a floating point instruction
[POWERPC] Enable interrupts if we are doing fp math emulation
[POWERPC] Added kprobes support to ppc32
[POWERPC] Make pSeries use the H_BULK_REMOVE hypervisor call
[POWERPC] Clear RI bit in MSR before restoring r13 when returning to userspace
[POWERPC] Fix performance monitor exception
[POWERPC] Compile fixes for arch/powerpc dcr code
[POWERPC] Maple: use mmio nvram
...
This driver is a modified version of the Attansic reference driver
for the L1 ethernet adapter. Attansic has granted permission for
its inclusion in the mainline kernel.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (28 commits)
sysfs: Shadow directory support
Driver Core: Increase the default timeout value of the firmware subsystem
Driver core: allow to delay the uevent at device creation time
Driver core: add device_type to struct device
Driver core: add uevent vars for devices of a class
SYSFS: Fix missing include of list.h in sysfs.h
HOWTO: Add a reference to Harbison and Steele
sysfs: error handling in sysfs, fill_read_buffer()
kobject: kobject_put cleanup
sysfs: kobject_put cleanup
sysfs: suppress lockdep warnings
Driver core: fix race in sysfs between sysfs_remove_file() and read()/write()
driver core: Change function call order in device_bind_driver().
driver core: Don't stop probing on ->probe errors.
driver core fixes: device_register() retval check in platform.c
driver core fixes: make_class_name() retval checks
/sys/modules/*/holders
USB: add the sysfs driver name to all modules
SERIO: add the sysfs driver name to all modules
PCI: add the sysfs driver name to all modules
...
The Atmel MACB Ethernet peripheral is also integrated in the AT91SAM9260
and AT91SAM9263 processors. The differences from the AVR32 version are:
* Single peripheral clock.
* MII/RMII selection bit is inverted.
* Clock enable bit.
Original patch from Patrice Vilchez.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More new chip id's from vendor driver version 10.0.4.3
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is basic support for the new Yukon Extreme
chip, extracted from the new vendor driver 10.0.4.3.
Since this is untested hardware, it has a big fat warning for now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rather than trying to be "smart" about possible transmit timeout
causes. Just clear all pending frames and reset the PHY.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC_U chipset apparently supports TSO but only for non-Jumbo
frame sizes because it lacks a Ram buffer.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the standard dev_xxx functions instead of printk directly for
error reports. Fix a bug where the initialization would return 0
if allocation of network device failed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I don't see any reason why we need pci_msi_quirk, quirk code can just
call pci_no_msi() instead.
Remove the check of pci_msi_quirk in msi_init(). This is safe as all
calls to msi_init() are protected by calls to pci_msi_supported(),
which checks pci_msi_enable, which is disabled by pci_no_msi().
The pci_disable_msi routines didn't check pci_msi_quirk, only
pci_msi_enable, but as far as I can see that was a bug not a feature.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds basic magic packet wake on lan support to the sky2 driver.
Note: initial WOL value is based on BIOS settings.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent an unaligned exception to occur. (GCC 4.1) tmp is defined as char
pointer while it is later accessed as short.
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the unused kernel config option DLCI_COUNT.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Krzysztof Halasa {khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At some point someone added a spin_lock(&dev->lock) to the IRQ handler for
the Z85230 driver. This actually correctly fixes a bug but the necessary
changes to remove the chan->lock calls in the event handlers were not made
(c->lock is the same lock).
Simona Dascenzo reported the problem with the driver and this patch should
fix the problem he found.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a set of changes that converts the PMAD-A support to the driver model.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the hardware perceive the RX descriptor ring as a null-terminated linked
list, instead of a circular ring.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename some internal ipw2100 debugging macros to not look like
user-settable kernel config settings.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This causes a lot of uninteresting output in noisy environments, and
doesn't really serve any purpose.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added update of network device error statistics.
Based on earlier work by Maxime Austruy.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This resets the device in the probe call. It does work with
2.6.19.2 including the softmac patches. It might fix the
reboot/reset problems a lot of people reported.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The in-kernel bcm43xx driver only works with V3 firmware, whereas the
experimental version that incorporates the d80211 stack requires V4
firmware. In bcm43xx-d80211, the fwpostfix module parameter is used
to differentiate between the versions. In bcm43xx-softmac, this
module parameter is only enabled when debugging is on. This patch
makes the module parameter available unconditionaly, and should
ease the future transition from softmac to d80211.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bcm43xx driver returns the available frequencies to 'iwlist freq'
with the wrong scaling.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bcm43xx scales the rate information supplied to a WE iwlist rate
call incorrectly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some versions of the bcm43xx chips only support 30-bit DMA, which means
that the descriptors and buffers must be in the first 1 GB of RAM. On
the i386 and x86_64 architectures with more than 1 GB RAM, an incorrect
assignment may occur. This patch ensures that the various DMA addresses
are within the capability of the chip. Testing has been limited to x86_64
as no one has an i386 system with more than 1 GB RAM.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
usb_init should call destroy_workqueue when usb_register fails.
Signed-off-by: Maxime Austruy <maxime@tralhalla.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets the network core have the ability to handle suspend/resume
issues, if it wants to.
Thanks to Frederik Deweerdt <frederik.deweerdt@gmail.com> for the arm
driver fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the
current kernel. Current patch fixes it, as well as other inconsistencies
expressed, that do not permit targets from working properly:
- Updated dts with a chosen node with interrupt controller,
- fixed messed device IDs among CPM2 SoC devices,
- corrected odd header name and fixed type in defines,
- Added 82xx subdir to the powerpc/platforms Makefile, missed during
initial commit,
- new solely-powerpc header file for 8260 family (was using one from
arch/ppc, this one cleaned up from the extra stuff), in fact for now
a placeholder to get the board-specific includes for stuff not yet
capable to live with devicetree peeks only
- Fixed couple of misprints in reference mpc8272 dts.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the inline function "is_power_of_2()" to log2.h, where the value
zero is *not* considered to be a power of two.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
drivers/net/amd8111e.c::amd8111e_poll() contains local_irq_disable() after
local_save_flags(). Turn it into local_irq_save().
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/3c59x.c::poll_vortex() contains local_irq_disable() after
local_save_flags(). Turn it into local_irq_save().
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert pci_module_init() to pci_register_driver().
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Added ethtool support for user level firmware management utilities.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark this as 1.10 because WOL now works
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add WOL support for Yukon chipsets in skge device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use dev_printk related macros for PCI related errors and warnings
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some motherboards are broken and have no address set. Failing at probe time
prevents the device from ever being used (like to download a fixed BIOS). Instead
warn on probe and check again when device is brought up. That way the address
can be set.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver for the PA Semi PWRficient on-chip Ethernet (1/10G)
Basic enablement, will be complemented with performance enhancements
over time. PHY support will be added as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removed namespace collisions due to usage of nic_t as per Ralf's patch
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Fix for updating skb->truesize properly.
2. Disable NAPI only if more than one ring configured in case of MSI/MSI-X
interrupts. Previously we were disabling NAPI irrespective of number of
rings when MSI/MSI-X interrupts were used.
3. Code cleanup.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Fix for reset and link handling.
2. Allow for promiscuos mode and multicast state be maintained through
ifconfig up and down.
3. Support to print adapter serial number.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds two load parameters napi and ufo. Previously NAPI was
compilation option with these changes wan enable disable NAPI using load
parameter. Also we are introducing ufo load parameter to enable/disable
ufo feature
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The attached patch adds an alternative driver "pc300too" for PCI WAN
cards PC300/RSV and PC300/X21 made by Cyclades Corp. (now Avocent Corp).
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some cases, SG_DATA_INTR won't clear on read and the following
interrupt may cause us to assert because NAPI is already scheduled.
Remove the assertion, NAPI can handle attempts to rearm it while
it's already scheduled.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
