3945 does not have update_chain_flags defined and because if this we always
see the debug message that does not apply to it. Add a check to be specific
about what is actually happening.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some concerns were raised about the automatic adjustment
of sleep intervals to all the same, potentially high,
value, and I can imagine the hardware behaving better
when we don't ask too much of it.
So let's convert to use a succession of sleep levels
when requesting to go to deeper sleeps (which can only
happen with large DTIM intervals), using the succession
values from power level three, which have the benefit of
also having been tested extensively already.
As a result, the automatic sleep level adjustment will
now be mostly equivalent to power level three, except
for the RX/TX timeouts and possibly using smaller sleep
vectors to account for networking latency.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For HT packets, mac80211 expects the rate_idx to be an MCS number, which is the
lower byte of rate_n_flags. However, iwl_hwrate_to_plcp_idx takes the MCS
number and reduces it down to the range 0-8 (6 to 60 Mbps), removing the bits
that signify multiply streams, HT40 Duplicate mode, or unequal modulation.
This version is used for various internal purposes through the driver.
Add the function iwl_hwrate_get_mac80211_idx, an alternate version which takes
the rate and the band and returns the mac80211 index (MCS, for HT packets, and
PLCP rate, for legacy packets).
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor and correct rate selection for outgoing transmitted
packets.
First, note that HT rates in the mac80211 rate table do not provide valid
indices when ieee80211_get_tx_rate is called; the check to see if we could to
abort a transmission early in iwl_tx_skb() would thus occasionally read invalid
memory and occasionally stall transmission (if the erroneous byte was 0xff).
We remove that code; the check wasn't valid anyway.
Second, iwl_tx_cmd_build_rate() also called ieee80211_get_tx_rate to be used
for sending management packets, which do not use the uCode station table. This
patch refactors that function and adds comments to enhance legibility, replaces
the call to ieee80211_get_tx_rate() with a direct lookup, and adds error
handling in case the table entry is invalid.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_supported_band is supposed to only contain legacy rates in the
bitrates table (HT rates go in the ieee80211_sta_ht_cap substruct). Make
iwlwifi driver obey this restriction by removing the 60 Mbps rate. Also, clean
up a few pieces of other code that formerly relied on 60 Mbps being in
sband->bitrates.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Single line log messages should be emitted by a single call
where possible.
Converted multiple calls to DBG_PRINT to single call form.
Removed "s2io:" preface from DBG_PRINTs.
The DBG_PRINT macro now emits a log level and is surrounded by
a do {...} while (0)
All s2io log output is now prefaced with KBUILD_MODNAME ": "
via pr_fmt.
The DBG_PRINT macro should probably be converted to use the
dev_<level> form eventually.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missed doing the conversion in earlier patch.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regularize the declaration and uses of
struct config_param *config = &sp->config;
struct mac_info *mac_control = &sp->mac_control;
and use
struct stat_block *stats = mac_control->stats_info;
struct swStat *swstats = &stats->sw_stat;
struct xpakStat *xstats = &stats->xpak_stat;
and convert the longish uses like
nic->mac_control.stats_info->sw_stat.<foo>
to
swstats-><foo>
etc.
This also makes the statistics code marginally smaller
and presumably faster.
Old:
$ size s2io.o
text data bss dec hex filename
114289 516 33360 148165 242c5 s2io.o
New:
$ size s2io.o
text data bss dec hex filename
114097 516 33360 147973 24205 s2io.o
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed trivial typo as well
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Still has a few long lines.
checkpatch was:
total: 263 errors, 53 warnings, 8751 lines checked
is:
total: 4 errors, 35 warnings, 8767 lines checked
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use consistent style. Don't calculate the kmalloc size multiple times
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Repeated variable use and line wrapping is hard to read.
Use temp variables instead of direct references.
struct fifo_info *fifo = &mac_control->fifos[i];
struct ring_info *ring = &mac_control->rings[i];
struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pfifo_fast_enqueue has this check:
if (skb_queue_len(list) < qdisc_dev(qdisc)->tx_queue_len) {
which allows each band to enqueue upto tx_queue_len skbs for a
total of 3*tx_queue_len skbs. I am not sure if this was the
intention of limiting in qdisc.
Patch compiled and 32 simultaneous netperf testing ran fine. Also:
# tc -s qdisc show dev eth2
qdisc pfifo_fast 0: root bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
Sent 16835026752 bytes 373116 pkt (dropped 0, overlimits 0 requeues 25)
rate 0bit 0pps backlog 0b 0p requeues 25
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch compiled and 32 simultaneous netperf testing ran fine.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch compiled and 32 simultaneous netperf testing ran fine.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dropped skb's should be documented by an appropriate return value.
Use the correct NET_RX_DROP and NET_RX_SUCCESS values for that reason.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the tests that check whether Frame* bits are not set
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements suspend/resume and WOL support for UCC Ethernet
driver.
We support two wake up events: wake on PHY/link changes and wake
on magic packet.
In some CPUs (like MPC8569) QE shuts down during sleep, so magic packet
detection is unusable, and also on resume we should fully reinitialize
UCC structures.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes currently unused UGETH_MAGIC_PACKET Kconfig symbol
and code, i.e. magic_packet_detection_{enable,disable} functions.
The two functions each contain just two steps that we'll place into
suspend/resume code path under CONFIG_PM.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch factors out MAC initialization into ucc_geth_init_mac()
function that we'll use for suspend/resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some CPUs (i.e. MPC8569) QE shuts down completely during sleep,
drivers may want to know that to reinitialize registers and buffer
descriptors.
This patch implements qe_alive_during_sleep() helper function, so far
it just checks if MPC8569-compatible power management controller is
present, which is a sign that QE turns off during sleep.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 3e73fc9a12 ("ucc_geth: Fix IO
memory (un)mapping code") I fixed ug_regs IO memory leak by properly
freeing the allocated memory. But ethtool_stats() callback doesn't
check for ug_regs being NULL, and that causes following oops if
'ethtool -S' is executed on a closed eth device:
Unable to handle kernel paging request for data at address 0x00000180
Faulting instruction address: 0xc0208228
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0208228] uec_get_ethtool_stats+0x38/0x140
LR [c02559a0] ethtool_get_stats+0xf8/0x23c
Call Trace:
[ef87bcd0] [c025597c] ethtool_get_stats+0xd4/0x23c (unreliable)
[ef87bd00] [c025706c] dev_ethtool+0xfe8/0x11bc
[ef87be00] [c0252b5c] dev_ioctl+0x454/0x6a8
...
---[ end trace 77fff1162a9586b0 ]---
Segmentation fault
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tx_prod, tx_cons, tx_pending, tx_ring, and
tx_buffers transmit ring device members to a per-interrupt structure.
It also adds a new transmit producer mailbox member (prodmbox) and
converts the code to use it rather than a preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the rx_rcb, rx_rcb_mapping, and rx_rcb_ptr return ring
device members to a per-interrupt structure. It also adds a new return
ring consumer mailbox register member (consmbox) and converts the code
to use it rather than a preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the last_tag, last_tag_irq, and hw_status device
members to a per-interrupt structure. It also adds a new interrupt
mailbox member (int_mbox) and converts the code to use it rather than a
direct preprocessor constant.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the napi interrupt handler functions to accept and
use tg3_napi structures.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates the ISR parameter from struct net_device to struct
tg3_napi. Checkpatch complains about the existence of the preexisting
IRQF_SAMPLE_RANDOM flag. I've opted to keep this patch conservative and
let it continue to exist until the flag gets officially purged from the
kernel.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a per-interrupt data structure, moves the napi
member over, and creates a tg3 pointer back to the device structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later patches will be adding MSIX support, which will complicate
interrupt initialization. This patch prepares for the integration by
breaking out the interrupt setup and teardown code into separate
functions and cleaning up the error return paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 only uses extended buffer descriptors for the jumbo producer
ring. Extended buffer descriptors are available on all devices that
support a separate jumbo producer ring so make the change universal.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates most of the rx producer ring variables to a new
tg3_rx_prodring_set structure and modifies the code accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later patches are going to complicate the ring initialization routines.
This patch breaks out the setup and teardown of the rx producer rings
into separate functions to make the code more readable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to document the various rx buffer sizes used by the
driver and how they relate to each other.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves where the jumbo capable and msi support flags are
located. This is prep work for the addition of msix support flags.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates the code that sets up the mini producer ring from
the code that sets up the jumbo producer rings. The 5717 asic rev
devices do not have a mini ring, but do have a jumbo frame
implementation similar to the 5704 and previous devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes up the NVRAM detection switch statements to conform
to the kernel coding style.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device firmware uses the MDIO bus during early setup. If the driver
modifies the MDIO bus configuration while it is in use by the firmware,
any number of bad things can happen. This patch delays MDIO setup until
after the firmware posts its magic signature, signifying initialization
is complete.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the bearer_priority to be less than TIPC_MIN_LINK_PRI and greater than
TIPC_MAX_LINK_PRI is logically impossible.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
create_proc_read_entry() is going to be removed soon.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method of ETHER_LINK pin is board dependence.
This patch adding paramters are:
- no_ether_link : If set to 1, do not use ETHER_LINK
- ether_link_active_low : If set to 1, ETHER_LINK is active low.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On TI's DA850/OMAP-L138 EVM, MAC address is stored in SPI
flash which is accessed using MTD interface.
This patch delays the initialization of DaVinci EMAC driver
by changing module_init to late_initcall. This helps SPI and
MTD drivers to get initialized before EMAC thereby enabling
EMAC driver to read the MAC address while booting and use it.
Tested with NFS on DM644x, DM6467, DA830/OMAP-L137 and
DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
