The Kconfig symbol SERIAL_TEXT_DEBUG was removed from
arch/powerpc/Kconfig.debug in v2.6.22. (In v2.6.27 it was also removed
from arch/ppc/Kconfig.debug.) So the check for its macro has evaluated
to false for over five years now. Remove that check and the few lines
of code hidden behind it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Vector Crypto category instructions are supported by current POWER8
chips, advertise them to userspace using a specific bit to properly
differentiate with chips of the same architecture level that might not
have them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.10+]
display rework fixes lots of displayport issues.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (43 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
We were sending the necessary state changes to unset the mode, but
never actually hit the big GO button unless another modeset happens
afterwards.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
SOR_PWR has no effect to power-off DP links, unlike other SOR protocols.
Instead, on the source side, we cut power to the lanes after having put
the sink into D3. Link training takes care of everything required to
bring it back again.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This previously worked for the most part due to userspace doing a
modeset in response to HPD interrupts. This will allow us to
properly handle cases where sync is lost for other reasons, or if
userspace isn't caring.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will, at some point, be used to replace various bits and pieces of
code doing direct bios parsing. For now, it'll just be used for some
DP improvements.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's also provisions to allow a pad to be locked with a specific
routing, for an indefinite period of time. This will be used in
future patches.
The G94+ pad driver will now also power-down pads when not required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was a half-finished hack before, just enough to handle the shared
aux/i2c pad thing on G94 and up.
We got lucky with locking etc up until now, as this was (generally) all
protected by the DRM mode_config lock. It's about to become a lot more
likely to hit the races.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Re-uses the implementation's accessor functions rather than requiring
and init/fini implementation for each chipset.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Hariprasad Shenai says:
====================
Adds support for CIQ and other misc. fixes for rdma/cxgb4
This patch series adds support to allocate and use IQs specifically for
indirect interrupts, adds fixes to align ISS for iWARP connections & fixes
related to tcp snd/rvd window for Chelsio T4/T5 adapters on iw_cxgb4.
Also changes Interrupt Holdoff Packet Count threshold of response queues for
cxgb4 driver.
The patches series is created against 'net-next' tree.
And includes patches on cxgb4 and iw_cxgb4 driver.
Since this patch-series contains cxgb4 and iw_cxgb4 patches, we would like to
request this patch series to get merged via David Miller's 'net-next' tree.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug that shows up with recv window sizes that exceed the size of
the RCV_BUFSIZ field in opt0 (>= 1024K). If the recv window exceeds
this, then we specify the max possible in opt0, add add the rest in via
a RX_DATA_ACK credits.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
