Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Joseph Fannin reported that hpet_rtc_interrupt() enables hardirqs
in irq context:
[ 25.628000] [<c014af4e>] trace_hardirqs_on+0xce/0x200
[ 25.628000] [<c036cf21>] _spin_unlock_irq+0x31/0x70
[ 25.628000] [<c0296584>] rtc_get_rtc_time+0x44/0x1a0
[ 25.628000] [<c01198bb>] hpet_rtc_interrupt+0x21b/0x280
[ 25.628000] [<c0161141>] handle_IRQ_event+0x31/0x70
[ 25.628000] [<c0162d37>] handle_edge_irq+0xe7/0x210
[ 25.628000] [<c0106192>] do_IRQ+0x92/0x120
[ 25.628000] [<c0104121>] common_interrupt+0x25/0x2c
the call of rtc_get_rtc_time() is highly suspect. At a minimum we
need the patch below to save/restore hardirq state.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Joseph Fannin <jfannin@gmail.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like someone confused kmem_cache_create with a different allocator
and was attempting to give it knowledge of how many cache entries there
were.
With the unfortunate result that each slab entry was big enough to hold
every irq.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is confirmed to fix a hang due to PCI resource conflicts with
setting up the Cardbus bridge on old laptops with the 440MX chipsets.
Original report by Alessio Sangalli, lspci debugging help by Pekka
Enberg, and trial patch suggested by Daniel Ritz:
"From the docs available i would _guess_ this thing is really similar
to the 82443BX/82371AB combination. at least the SMBus base address
register is hidden at the very same place (32bit at 0x90 in function
3 of the "south" brigde)"
The dang thing is largely undocumented, but the patch was corroborated
by Asit Mallick:
"I am trying to find the register information. 440MX is an integration of
440BX north-bridge without AGP and PIIX4E (82371EB). PIIX4 quirk
should cover the ACPI and SMBus related I/O registers."
and verified to fix the problem by Alessio.
Cc: Daniel Ritz <daniel.ritz-ml@swissonline.ch>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Tested-by: Alessio Sangalli <alesan@manoweb.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The module parameters for xpram are not or in a wrong way parsed.
The xpram module uses the module_param_array directive with an int
parameter which causes the kernel to automatically parse the passed
numbers. This will cause errors if arguments are omitted or cause
wrong results if arguments have size qualifiers.
Use module_param_array with charp and parse the arguments later.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a reg_mutex to prevent unregistering a subchannel before it has been
registered. Since 2.6.17, we've seen oopses in kslowcrw when a device is
found to be not operational during sense id when doing initial device
recognition; it is not clear yet why that particular problem was not (yet)
observed with earlier kernels...
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: ACPI_DOCK: Initialize the atomic notifier list
ACPI: acpi_os_allocate() fixes
ACPI: SBS: fix initialization, sem2mutex
ACPI: add 'const' to several ACPI file_operations
ACPI: delete some defaults from ACPI Kconfig
ACPI: "Device `[%s]' is not power manageable" make message debug only
ACPI: ACPI_DOCK Kconfig
Revert "Revert "ACPI: dock driver""
ACPI: acpi_os_get_thread_id() returns current
ACPI: ACPICA 20060707
* HEAD:
[DCCP]: Fix sparse warnings.
[TCP]: Remove TCP Compound
[BPQ] lockdep: fix false positive
[IPV4] inetpeer: Get rid of volatile from peer_total
[AX.25]: Get rid of the last volatile.
No need for video to be always in
No need for smart battery driver to be always in
Acked-by: Len Brown <len.brown@intel.com>
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bpqether is encapsulating AX.25 frames into ethernet frames. There is a
virtual bpqether device paired with each ethernet devices, so it's normal
to pass through dev_queue_xmit twice for each frame which triggers the
locking detector.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a proper prototype for i2o_parm_issue() in core.h.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the snsc driver uses force_sig to send init a SIGPWR when the
system overheats. This patch switches it to kill_proc instead which has
the following advantages:
(1) gets rid of one of the last remaining tasklist_lock users
in modular code
(2) simplifies the snsc code significantly
The downside is that an init implementation could in theory block SIGPWR
and it would not get delivered. The sysvinit code used by all major
distributions doesn't do this and blocking this signal in init would be a
rather stupid thing to do.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Switch from register_chrdev() to (register|alloc)_chrdev_region().
- use a cdev. This was intended for original patchset, but was
overlooked.
We use a single cdev for all pins (minor device-numbers), as gleaned
from cs5535_gpio, and in contrast to whats currently done in scx200_gpio
(which I'll fix soon)
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix module-init-func by repairing usage of platform_device_del/put in
module-exit-func. IOW, it imitates Ingo's 'mishaps' patch, which fixed the
module-init-func's undo handling.
Also fixes lack of release_region to undo the earlier registration.
Also starts to 'use a cdev' which was originally intended (its present in
scx200_gpio). Code compiles and runs, exhibits a lesser error than
previously. (re-register-chrdev fails)
Since I had to add "include <linux/cdev.h>", I went ahead and made 2
tweaks that fell into diff-context-window:
- remove include <linux/config.h> everyone's doing it
- copyright updates - current date is 'wrong'
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add LED Class device support for the Soekris net48xx Error LED. Tested
only on a net4801, but should work on a net4826 as well. I'd love to find
a way of detecting a Soekris net48xx device but there is no DMI or any
Soekris-specific PCI devices.
[akpm@osdl.org: fixlets, cleanups]
Signed-off-by: Chris Boot <bootc@bootc.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle memory-mapped chips properly, needed for example on DECstations.
This support was in Linux 2.4 but for some reason got lost in 2.6. This
patch is taken directly from the linux-mips repository.
[akpm@osdl.org: cleanup]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: Paul Gortmaker <penguin@muskoka.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Newer ARMs have a 40 bit physical address space, but mapping physical
memory above 4G needs a special page table format which we (currently?) do
not use for userspace mappings, so what happens instead is that mapping an
address >= 4G will happily discard the upper bits and wrap.
There is a valid_mmap_phys_addr_range() arch hook where we could check for
>= 4G addresses and deny the mapping, but this hook takes an unsigned long
address:
static inline int valid_mmap_phys_addr_range(unsigned long addr, size_t size);
And drivers/char/mem.c:mmap_mem() calls it like this:
static int mmap_mem(struct file * file, struct vm_area_struct * vma)
{
size_t size = vma->vm_end - vma->vm_start;
if (!valid_mmap_phys_addr_range(vma->vm_pgoff << PAGE_SHIFT, size))
So that's not much help either.
This patch makes the hook take a pfn instead of a phys address.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When EDAC was first introduced into the kernel it had a sysfs interface,
but due to some problems it was disabled in 2.6.16 and remained disabled in
2.6.17.
With feedback, several of the control and attribute files of that interface
had some good constructive feedback. PCI Blacklist/Whitelist was a major
set which has design issues and it has been removed in this patch. Instead
of storing PCI broken parity status in EDAC, it has been moved to the
pci_dev structure itself by a previous PCI patch. A future patch will
enable that feature in EDAC by utilizing the pci_dev info.
The sysfs is now enabled in this patch, with a minimal set of control and
attribute files for examining EDAC state and for enabling/disabling the
memory and PCI operations.
The Documentation for EDAC has also been updated to reflect the new state
of EDAC operation.
Signed-off-by:Doug Thompson <norsk5@xmisson.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whoops, better hope this never gets passed a null dev in its current state.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andreas Herrmann <aherrman@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two variables in drivers/s390/net/qeth_main.c:qeth_send_packet() are only
used if CONFIG_QETH_PERF_STATS. Move their definition under the same ifdef
to remove compiler warning.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the roundup() macro from binfmt_elf.c into linux/kernel.h as it's
generally useful.
[akpm@osdl.org: nuke all the other implementations]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We all failed to notice that Franck's recent update to usb-storage allowed
an URB to complete after its context data was no longer valid. This patch
(as746) makes the driver wait for the URB to complete whenever there's a
timeout.
Although timeouts in usb-storage are relatively uncommon, they do occur.
Without this patch the code in 2.6.18-rc1 will fault within an interrupt
handler, which is not nice at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pci channel state is currently uninitialized, thus there are two ways
of indicating that "everything's OK": 0 and 1. This is a bit of a burden.
If a devce driver wants to check if the pci channel is in a working or a
disconnected state, the driver writer must perform checks similar to
if((pdev->error_state != 0) &&
(pdev->error_state != pci_channel_io_normal)) {
whatever();
}
which is rather akward. The first check is needed because stuct pci_dev is
inited to all-zeros. The scond is needed because the error recovery will
set the state to pci_channel_io_normal (which is not zero).
This patch fixes this awkwardness.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes several problems:
- pmac_backlight_key() is called under interrupt context, and therefore
can't use mutexes or semaphores, so defer the backlight level for
later, as it's not critical (original code by Aristeu S. Rozanski F.
<aris@valeta.org>).
- Add exports for functions that might be called from modules
- Fix Kconfig depdencies on PMAC_BACKLIGHT.
- Fix locking issues on calls from inside the driver (reported by
Aristeu S. Rozanski F., too)
- Fix wrong calculation of backlight values in some of the drivers
- Replace pmac_backlight_key_up/down by inline functions
[akpm@osdl.org: fix function prototypes]
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Aristeu S. Rozanski F. <aris@valeta.org>
Acked-by: Rene Nussbaumer <linux-kernel@killerfox.forkbomb.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SMU driver tries to map an interrupt from the device-tree before the
interrupt controllers in the machine have been enumerated. This doesn't work
properly and cause machines like the Quad g5 to fail booting later on when
some drivers waits endlessly for an SMU request to complete. This is the
second problem preventing boot on the Quad g5. This fixes it and also makes
the SMU driver a bit more resilient to not having an interrupt.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch slightly reworks the new irq code to fix a small design error. I
removed the passing of the trigger to the map() calls entirely, it was not a
good idea to have one call do two different things. It also fixes a couple of
corner cases.
Mapping a linux virtual irq to a physical irq now does only that. Setting the
trigger is a different action which has a different call.
The main changes are:
- I no longer call host->ops->map() for an already mapped irq, I just return
the virtual number that was already mapped. It was called before to give an
opportunity to change the trigger, but that was causing issues as that could
happen while the interrupt was in use by a device, and because of the
trigger change, map would potentially muck around with things in a racy way.
That was causing much burden on a given's controller implementation of
map() to get it right. This is much simpler now. map() is only called on
the initial mapping of an irq, meaning that you know that this irq is _not_
being used. You can initialize the hardware if you want (though you don't
have to).
- Controllers that can handle different type of triggers (level/edge/etc...)
now implement the standard irq_chip->set_type() call as defined by the
generic code. That means that you can use the standard set_irq_type() to
configure an irq line manually if you wish or (though I don't like that
interface), pass explicit trigger flags to request_irq() as defined by the
generic kernel interfaces. Also, using those interfaces guarantees that
your controller set_type callback is called with the descriptor lock held,
thus providing locking against activity on the same interrupt (including
mask/unmask/etc...) automatically. A result is that, for example, MPIC's
own map() implementation calls irq_set_type(NONE) to configure the hardware
to the default triggers.
- To allow the above, the irq_map array entry for the new mapped interrupt
is now set before map() callback is called for the controller.
- The irq_create_of_mapping() (also used by irq_of_parse_and_map()) function
for mapping interrupts from the device-tree now also call the separate
set_irq_type(), and only does so if there is a change in the trigger type.
- While I was at it, I changed pci_read_irq_line() (which is the helper I
would expect most archs to use in their pcibios_fixup() to get the PCI
interrupt routing from the device tree) to also handle a fallback when the
DT mapping fails consisting of reading the PCI_INTERRUPT_PIN to know wether
the device has an interrupt at all, and the the PCI_INTERRUPT_LINE to get an
interrupt number from the device. That number is then mapped using the
default controller, and the trigger is set to level low. That default
behaviour works for several platforms that don't have a proper interrupt
tree like Pegasos. If it doesn't work for your platform, then either
provide a proper interrupt tree from the firmware so that fallback isn't
needed, or don't call pci_read_irq_line()
- Add back a bit that got dropped by my main rework patch for properly
clearing pending IPIs on pSeries when using a kexec
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Daniel Ritz <daniel.ritz-ml@swissonline.ch> says:
The acpi driver suspend/resume patches that went in recently caused a regression
on my box (toshiba tecra 8000 laptop): after resume from swsusp the fan turns on
keeping blowing cold air out of my notebook. before the patches, the fan was off
and would only make noise when required. it's the same thing described in
bugzilla.kernel.org #5000. the acpi suspend/resume patches or at least parts of
them originate in this bug. now the last patch in the report (attach id 8438)
actually fixes the problem - for me and the reporter. this is a trimmed down
version of that patch.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Len Brown <len.brown@intel.com>
Cc: Sanjoy Mahajan <sanjoy@mrao.cam.ac.uk>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During early MD setup (superblock reading), we don't have a personality yet.
But the error-handling code tries to dereference mddev->pers. Fix.
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.
[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ioctl requires CAP_SYS_ADMIN, so sysfs should too. Note that we don't
require CAP_SYS_ADMIN for reading attributes even though the ioctl does.
There is no reason to limit the read access, and much of the information is
already available via /proc/mdstat
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some places we use number (0660) someplaces names (S_IRUGO). Change all
numbers to be names, and change 0655 to be what it should be.
Also make some formatting more consistent.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Though it rarely matters, we should be using 's' rather than r1_bio->sector
here.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment gives more details, but I didn't quite have the sequencing write,
so there was room for races to leave bits unset in the on-disk bitmap for
short periods of time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a device is unplugged, requests are moved from one or two (depending on
whether a bitmap is in use) queues to the main request queue.
So whenever requests are put on either of those queues, we should make sure
the raid5 array is 'plugged'. However we don't. We currently plug the raid5
queue just before putting requests on queues, so there is room for a race. If
something unplugs the queue at just the wrong time, requests will be left on
the queue and nothing will want to unplug them. Normally something else will
plug and unplug the queue fairly soon, but there is a risk that nothing will.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).
We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set. If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.
This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has to be done in ->load_super, not ->validate_super
Without this, hot-adding devices to an array doesn't always
work right - though there is a work around in mdadm-2.5.2 to
make this less of an issue.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have reports of a problem with raid5 which turns out to be because the raid5
device gets stuck in a 'plugged' state. This shouldn't be able to happen as
3msec after it gets plugged it should get unplugged. However it happens
none-the-less. This patch fixes the problem and is a reasonable thing to do,
though it might hurt performance slightly in some cases.
Until I can find the real problem, we should probably have this workaround in
place.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
screen_info.h doesn't have anything to do with the tty layer and shouldn't be
included by tty.h. This patches removes the include and modifies all users to
directly include screen_info.h. struct screen_info is mainly used to
communicate with the console drivers in drivers/video/console. Note that this
patch touches every arch and I have no way of testing it. If there is a
mistake the worst thing that will happen is a compile error.
[akpm@osdl.org: fix arm build]
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MAX_NR_CONSOLES, fg_console, want_console and last_console are more of a
function of the VT layer than the TTY one. Moving these to vt.h and vt_kern.h
allows all of the framebuffer and VT console drivers to remove their
dependency on tty.h.
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the warnings about the section mismatches for __init* in the HiSax
driver.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code really means to mask off the high bits, not assign 0xff.
Signed-off-by: Jens Axboe <axboe@suse.de>
Cc: Marcus Meissner <meissner@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>