- Release task management command before counting outstanding commands.
TMF was being erroneously counted as an active outstanding command.
- Serialize EH calls and block requests when EH function is running.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove locking wrappers around error handlers. Wrappers were added in
early 2.6.13 api change
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Miscellaneous Cleanups:
- Remove ProgType READ_REV mailbox command value check in lpfc_config_port_prep.
- Convert simple printk to an lpfc_printf_log in queuecommand.
- Modify lpfc_abort_handler message 0749 to display more accurate text and data.
- Minor style cleanup: fix 3 long lines in lpfc_hw.h
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use schedule_timeout_uninterruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Return FAILED from eh_ routines if command(s) is(are) not completed
There were scenarios where we may have returned from the error
handlers prior to all affected commands being flushed to the midlayer.
Add changes to ensure this doesn't happen.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adjust lpfc_scsi_buf allocation to account for lun_queue_depth and
error handling
Under high load and high duress, the error handler could steal some
command resources from the normal i/o path. Rework to allocate
additional resources to avoid this scneario.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace lpfc_sli_issue_iocb_wait_high_priority with lpfc_sli_issue_iocb_wait.
Simplify code paths, as there really wasn't a "priority"
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: James Smart <James.Smart@emulex.com>
There were scenarios where the error handlers could reuse an iotag
value of an active io. Remove all possibility of this by
pre-assigning iotag resources to command resources.
Signed-off-by: James Smart <James.Smart@emulex.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace use of lpfc_put_lun with midlayer's int_to_scsilun
Remove driver's local definition of lpfc_put_lun (which converts an
int back to a 64-bit LUN) and replace it's use with the recently added
int_to_scsilun function provided by the midlayer.
Note: Embedding midlayer structure in our structure caused
need for more files to include midlayer headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix handling of the dev_loss and nodev timeouts.
Symptoms: when remote port disappears for a period of time longer then
either nodev_tmo or dev_loss_tmo, the lpfc driver worker thread will
stall removing that remote port.
Cause: removing remote port involves un-blocking and sync-ing
corresponding block device queue. But corresponding node in the lpfc
driver is still in the NPR(?node port recovery?) state and mid-layer
gets SCSI_MLQUEUE_HOST_BUSY as a return value when it is trying to call
queuecommand() with command for that node (AKA remote port)
Fix: Instead of returning SCSI_MLQUEUE_HOST_BUS from queuecommand() for
nodes in NPR states complete it with retry-able error code DID_BUS_BUSY
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clear task management bits when preparing SCSI commands
In lpfc_scsi_prep_cmnd, clear the task management bits (fcpCntl2 member
in the fcp_cmd structure) when preparing regular SCSI commands.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IOCB BDE not getting fully initialized during reuse
Symptoms: Driver gets Status 3 and Reason 0x13 on IOCB completions.
Cause: The IOCB bpl.bdeSize and bdeFlags are not getting initialized on reuse.
Fix: Reinitialize these fields in prep_dma each time an IOCB is used.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update copyright notice text and include year 2005.
Add Copyright notice for Christoph Hellwig to several files: lpfc.h
lpfc_attr.c lpfc_els.c lpfc_hbadisc.c lpfc_init.c lpfc_mbox.c
lpfc_mem.c lpfc_nportdisc.c lpfc_scsi.c lpfc_sli.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add completion handler to the abort iocbs to close a hole where we
could reuse an iotag.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add max_sectors to the driver host template and initialize it with
0xFFFF since the driver has no limitations on the size a transfer
contained by a scsi command and that fits within the sg_tablesize
provisioned by the driver. This fixes a performance issue seen in
some configurations.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
