* add ide_use_fast_pio() helper for use by host drivers
* add DMA capability and hwif->autodma checks to ide_use_dma()
- au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)
[ for the IT8211/2 in SMART mode this check shouldn't be made but since
in it821x_fixups() we set DMA bit explicitly:
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id->capability |= 3; /* LBA28, DMA */
we are better off using generic helper if we can ]
- ide-cris driver didn't set ->autodma
[ before the patch hwif->autodma was only checked in the chipset specific
hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
function so there no behavior change here ]
v2:
* updated patch description (thanks to Alan Cox for the feedback)
v3:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In cmd64x, siimage and scc_pata drivers:
* don't set drive->init_speed as it should be already
set by successful execution of ide_set_xfer_rate()
* use hwif->speedproc functions directly
Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate).
v2:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_dma_speed() fails to actually honor the IDE drivers' mode support
masks) because of the bogus checks -- thus, selecting the DMA transfer mode
that the driver explicitly refuses to support is possible. Additionally,
there is no check for validity of the UltraDMA mode data in the drive ID,
and the function is misdocumented.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
Michal Piotrowski reported the following validator assert:
hdd: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdd: set_drive_speed_status: error=0xb4 { AbortedCommand LastFailedSense=0x0b }
============================
[ BUG: illegal lock usage! ]
----------------------------
illegal {in-hardirq-W} -> {hardirq-on-W} usage.
hdparm/1821 [HC0[0]:SC0[0]:HE1:SE1] takes:
(ide_lock){++..}, at: [<c0268388>] ide_dump_opcode+0x13/0x9b
[...]
stack backtrace:
[<c0104513>] show_trace+0x1b/0x20
[<c01045f1>] dump_stack+0x1f/0x24
[<c013976c>] print_usage_bug+0x1a5/0x1b1
[<c0139e90>] mark_lock+0x2ca/0x4f7
[<c013aa96>] __lockdep_acquire+0x47e/0xaa4
[<c013b536>] lockdep_acquire+0x67/0x7f
[<c030552d>] _spin_lock+0x24/0x32
[<c0268388>] ide_dump_opcode+0x13/0x9b
[<c02688b6>] ide_dump_status+0x4a6/0x4cc
[<c0267ae6>] ide_config_drive_speed+0x32a/0x33a
[<c0262dc5>] piix_tune_chipset+0x2ed/0x2f8
[<c0262e31>] piix_config_drive_xfer_rate+0x61/0xb5
[<c0263a82>] set_using_dma+0x2f/0x60
[<c0263bee>] ide_write_setting+0x4a/0xc3
[<c02647ca>] generic_ide_ioctl+0x8a/0x47f
[<f886003a>] idecd_ioctl+0xfd/0x133 [ide_cd]
[<c01f1fff>] blkdev_driver_ioctl+0x4b/0x5f
[<c01f2783>] blkdev_ioctl+0x770/0x7bd
[<c017dc0d>] block_ioctl+0x1f/0x21
[<c0189353>] do_ioctl+0x27/0x6e
[<c0189604>] vfs_ioctl+0x26a/0x280
[<c0189667>] sys_ioctl+0x4d/0x7e
[<c0305ed2>] sysenter_past_esp+0x63/0xa1
in ide_dump_opcode() takes the ide_lock in an irq-unsafe manner, i.e. this
function expects to be called with irqs disabled. But
ide_dump_ata[pi]_status() doesnt do that - it enables interrupts specifically.
That is a no-no - what guarantees that another IDE port couldnt generate an
IDE interrupt while we are dumping this error? The fix is to turn the
irq-enabling in these functions into irq-disabling.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch fixes a crash caused by attempting to bounce buffer
when an IDE CD-ROM is used on a machine with an IO-MMU. [At least, this
patch fixes things so I can use my IDE CD-ROM behind an ns87415 on a
HP PA-RISC workstation.]
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: Denis Vlasenko <vda@ilport.com.ua>
* printk("\n") is misplaced, resulting in stray empty line in kernel log
* cleanups nerby: some back-to-back printks are combined, etc
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
