Sound recording doesn't work for this card because ACNI and ACPF
are not set before snd_card_saa7134_capture_prepare(). As a result
timeout occurs. These registers aren't poked because thread
never gets wake up signal. ACNI initialization is done in the
thread.
Sound is muted when capture stops. Shouldn't be because it may
be used during TV playback.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following two pointers in struct cx8802_dev are unused - remove them:
void* fe_handle;
int (*fe_release)(void *handle);
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The old service_set_out setting was still tested, even though it no longer
was ever set and was in fact obsolete. This meant that everything that was
written to /dev/vbi16 was ignored. Removed the service_set_out variable
altogether and now it works again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make the driver depend on V4L2 only (KConfig)
- Better and safe locking mechanism of the device structure on open(), close()
and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make the driver depend on V4L2 only (KConfig)
- Better and safe locking mechanism of the device structure on open(),
close() and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for pair OV7630+SN9C120
- Better and safe locking mechanism of the device structure on open(),
close() and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move tuner callback function pointers out of struct tuner, into
struct tuner_operations.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Procfs support on V4L were converted to sysfs support by a pre-2.6 patch:
http://www.ussg.iu.edu/hypermail/linux/kernel/0307.1/2356.html
There's no sense on keeping the dead code inside vicam.c. Also,it won't
work anyway, as part of proc_fs support were previously inside
videodev.c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CONFIG_BIGPHYS_AREA is an out-of-tree kernel patch. It makes no sense to
keep supporting this on mainstream.
The out-of-tree compilation with CONFIG_BIGPHYS_AREA will still be
preserved at the v4l-dvb development tree at:
http://linuxtv.org/hg/v4l-dvb
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The line, "#include <media/tuner.h>" appears twice.
This patch removes the second occurance.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Makefiles in the dvb directory tree used '=' when defining EXTRA_CFLAGS
rather than '+=', which is far more common in the rest of the kernel source.
= 14 times (9 of which this patch removes)
:= 25 times
+= 123 times
This change also has certain advantages for the out of kernel v4l-dvb build
system.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Although it is safe to kfree(NULL), We only need to kfree(priv)
if the release callback is undefined. As it stands now, there
is some redundancy in the operation of releasing the priv data
structures. This patch will call kfree(priv) and set priv to NULL,
if the release callback isnt defined. Otherwise, let the release
callback handle this itself.
Thanks to Mauro Carvalho Chehab for suggesting this.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define tuner release callbacks for mt20xx, tda9887 and tda8290, so that
these drivers can release their own private structures themselves.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Individual tuner drivers are now allocating memory themselves for
their own private data structures. This changeset adds a release
callback to the tuner operations, so that newer drivers that may
require more complex data structures may release this private data
themselves.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a typo the tea5761 tuner support was dead code.
This patch also fixes a bug in the no longer dead code:
A void function can't return anything.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that cx88-blackbird is only accepting the official firmware image,
we no longer have any need to store the size of the firmware inside the
cx88 data structure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove temporary support for older 256 kB firmwares.
ivtv, pvrusb2 and blackbird can now all handle the newer larger firmwares,
so support for the older (buggier) firmware can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For backwards compatibility firmware files of 256 Kb were allowed: all
drivers have now been updated to support the newer larger firmwares so
remove this compatibility code and only support the newer firmware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vivi scatter method were used as a proof of concept. It can be
safelly removed from mainstream, since the current method is
faster and better than the previous solution.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Create private data struct for device specific private data.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the long-dead references to the obsolete MODULE_PARM macro.
Given that the first one of those is actually misspelled as
"MODULE_PARAM", it's clear that they can't have been doing any good.
Acked-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In preparation for struct class_device -> struct device input
core conversion switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor at mail.ru>
Acked-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make sure devices manufactured by Dposh are not affected by previous hw
pid filtering changes
Doing so might crash it.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes several return value related problems in zr364xx.
- return -ENOMEM instead of -ENODEV on out of memory
- zr364xx checks video_register_device() error only when
its return value is -1. But video_register_device() doesn't
always return -1 on error.
- If usb_register() returns error, module_init() wrongly returns 1:
retval = usb_register(&zr364xx_driver) < 0;
...
return retval;
And it allows the module to be loaded. Because sys_init_module() doesn't
see positive return value as error.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that dvb-pll is being used properly in all cx88-dvb instances,
the cx88 driver no longer needs to store pll_desc nor pll_addr.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Enhance the dvb-pll definition of the fmd1216 tuner by adding an init sequence
and a sleep sequence.
The init sequence sets the AGC control register to 0xa0, selecting the fast
time constant and 112 dBuV take-over point. This the recommended value for
DVB-T operation.
The sleep sequence sets bit P4 (which is believed to turn the analog
demodulator on), turns off the tuning voltage, and sets the AGC control
register to 0x60 (external AGC voltage, the recommended value for analog
operation).
The existing dvb-pll users in the cx88 driver, listed below, will gain these
init and sleep sequences.
CX88_BOARD_HAUPPAUGE_HVR1100 Hauppauge WinTV-HVR1100 DVB-T/Hybrid
CX88_BOARD_HAUPPAUGE_HVR1100LP Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profi
CX88_BOARD_WINFAST_DTV2000H WinFast DTV2000 H
CX88_BOARD_HAUPPAUGE_HVR3000 Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DV
CX88_BOARD_HAUPPAUGE_HVR1300 Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encod
This non-dvb-pll user in the cx88 driver should only gain the sleep sequence,
as it already had an equivalent init sequence. The non-dvb-pll code for this
user is removed.
X88_BOARD_DNTV_LIVE_DVB_T_PRO digitalnow DNTV Live! DVB-T Pro
In these saa7134 driver, these non-dvb-pll users are converted to use dvb-pll:
SAA7134_BOARD_MD7134 Medion 7134
SAA7134_BOARD_ASUS_EUROPA2_HYBRID Asus Europa2 OEM
The saa7134 functions philips_fmd1216_tuner_init(),
philips_fmd1216_tuner_sleep(), and philips_fmd1216_tuner_set_params() are
deleted and the dvb-pll versions are used.
This should result in equivalent sleep, init, and tuning sequences being sent
to the tuner.
For the cxusb driver, only one board is effected:
USB_PID_MEDION_MD95700 Medion MD95700
This board used dvb_usb_tuner_init_i2c() and dvb_usb_tuner_set_params_i2c()
for init and tuning, respectively. These functions are effectively the same
as the dvb-pll versions. They call a tuner pass control function defined at
the dvb-usb level, but this does not matter, as this card does not have a
tuner pass control function (only the dib3000mb does). This board will gain
the sleep sequence, while init and tuning should be unchanged.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support for A-LINK DTU(m) is not included in this patch.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Marked af9005 driver as experimental and add dependency for qt1010;
Added a dependency on qt1010 in Kconfig;
Corrected the experimental gain reduction of the mt2060 in case of
strong signal (though it is code included in #ifdef 0).
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
convert calls to dib3000mb_attach to use dvb_attach
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
moved tda665x pll_init into dvb_pll_desc dvb_pll_tda665x.initdata
convert handling of tda665x and tua6010xs to properly use dvb-pll
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These sources do not need to #include "dvb-pll.h"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Using Encore's key codes, we needn't add any additional key table.
Signed-off-by: Tony Wan <wankai@sjtu.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support the 10moons TM300 TV card (so called TV Master 3), which is a
10moons saa7130 based board. Here not include features for the
IR-remote.
It has been tested using TVTIME. The card was auto-detected and all the
input sources worked correct with sound.
Signed-off-by: Tony Wan <wankai@sjtu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ioctl entry point, a big switch/case, is splitted in little
functions.
These functions are set as callbacks for the video_ioctl2 video4linux
facility.
This improves the driver memory consumption and enables the v4l1
compatibility as a side effect.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Acked-by: Dwaine P. Garden <dwainegarden@rogers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Radio and video ioctls are the same,
delete the usbvision_do_radio_ioctl function
add the special cases for radio in usbvision_v4l2_do_ioctl
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
usbvision_set_video_format: add comment that VO_MODE is also being set.
Signed-off-by: David Warman <dwarman@davidwarman.net>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes duplicate code from cx88-dvb and saa7134-dvb that handles
rf input switching for the TUV1236d tuner.
The functionality is added to dvb-pll, where all the other code that
handles the TUV1236d is kept.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.
In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All the printks had missing level prefixes so I've fixed these too.
Also fixed some grammer errors.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If cx88 support is compiled into the kernel while vp3054 is left as a module,
the kernel will fail to link. Adjust the existing "#if" code in cx88 so
that it won't consider vp3054 to be supported in this case.
It might make sense to move vp3054 selection into the "customisation" menu
instead of a cx88 sub-option (though this is a cx88 feature, there is no extra
chip involved).
It might also make sense to use dvb_attach() to load vp3054 support.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if the call to budget_register() fails in ttpci_budget_int(),
ttpci_budget_init() returns success. The attached patch will
fix this problem.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Spotted and tested by Thomas Sattler <tsattler@gmx.de>.
cinergyT2.c does cancel_delayed_work() + flush_scheduled_work() while
holding cinergyt2->sem. This leads to deadlock because work->func()
needs the same mutex to complete. Another bug is that this code in fact
can't reliably stop the re-arming delayed_work.
Convert this code to use cancel_rearming_delayed_work() and move it
out of ->sem. Another mutex, ->wq_sem, was added to protect against the
concurrent open/resume.
This patch is a horrible hack to fix the lockup which happens in practice.
As Dmitry Torokhov pointed out this driver has other problems and needs
further changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
v4l-info and other programs would loop indefinitely while querying the
tuners for cx88-blackbird cards.
The cause was that vidioc_g_tuner didn't return an error value for
qctrl->id != 0, making the application think there is a never ending
list of tuners...
This patch adds the same index check as done in vidioc_g_tuner() in
cx88-video.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If one uses a V4L *one* application, such as vlc or mplayer's v4l driver, as
the first user after the driver is loaded, the driver wedges itself and will
never capture properly. Even if one uses a V4L2 application later, it still
won't work.
If one uses a V4L *two* application first, such as tvtime or mplayer's v4l2
driver, then the driver will be ok. One can then run a V4L1 application, and
it will work.
It turns out the problem is with norm changing and the crop support that was
added in 2.6.21. The driver defaults to PAL, and keeps the last norm it was
set too across opens. If one changes the norm via V4L1, the cropping
parameters are not reset like they should be, and they'll remain broken across
device opens.
This patch removes the direct setting of btv->tvnorm in the V4L1 ioctl
VIDIOCSCHAN handler. The norm is set via the existing call to set_input(),
which calls set_tvnorm(), which will reset the cropping values now that it is
able to detect the norm change.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the test for the thread pid from >= 0 to > 0.
When the saa8134 driver initialization fails after a certain point, it goes
through the complete shutdown process for the driver. Part of shutting it
down includes tearing down the thread for tv audio.
The test for tearing down the thread tests for >= 0. Since the dev
structure is kzalloc'd, the test will always be true if we haven't tried to
start the thread yet. We end up waiting on pid 0 to complete, which will
never happen, so we lock up.
This bug was observed in Novell Bugzilla 284718, when request_irq() failed.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If one has a dependency chain (tristate)FOO depends on (bool)BAR depends on
(tristate)BAZ, build problems will result. If BAZ=m, then BAR can be set
y, which allows FOO=y. It's possible to have FOO=y && BAZ=m, which
wouldn't be allowed if FOO depended directly on BAZ. In effect, the bool
promotes the tristate from m to y.
This ends up causing a problem with several menuconfigs that look like:
menuconfig BAR
bool
depends on BAZ [tristate]
if BAR
config FOO
tristate
endif
The solution used here is to add the dependencies of BAR to the if
statement, so that items in the if block will gain a direct
non-bool-promoted dependency on BAZ. This is how it would work if a menu
was used instead of an if block.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves flexcop-dma (currently used only by flexcop-pci) to
b2c2-flexcop-pci module, that is dependent on CONFIG_PCI, fixing the bug
as reported by Geert Uytterhoeven <geert@linux-m68k.org>:
drivers/media/dvb/b2c2/flexcop-dma.c uses the PCI DMA API, but
DVB_B2C2_FLEXCOP doesn't depend on PCI, causing the following problem on
PCI-less systems:
| linux/drivers/media/dvb/b2c2/flexcop-dma.c:20: warning: implicit declaration of function 'pci_alloc_consistent'
| linux/drivers/media/dvb/b2c2/flexcop-dma.c:20: warning: implicit declaration of function 'pci_alloc_consistent'
Apparently this is the flexcop DMA core, which is used by both
DVB_B2C2_FLEXCOP_PCI and DVB_B2C2_FLEXCOP_USB.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VIDIOC_CROPCAP ioctl was missing in ivtv.
The handling of output video cropping was wrong. This has now been fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L2_CAP_VIDEO_OUTPUT_POS was initially introduced for 2.6.22 but never
actually used: remove it before the final 2.6.22 is made.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed the urb allocation part that was not taking into account the current alternate setting
this fixes usb_submit_urb returning -90 errno in isocIrq.
- fixed usb_submit_urb returning -1 errno in isocIrq (need to ignore usb urb with status==-ENOENT)
Acked-by: Dwaine P. Garden <dwainegarden@rogers.com>
Signed-off-by: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several people reported unreliable reception with the current driver.
Furthermore, STR and SNR values seem to be inverted.
This fix is based on a patch posted by Hartmut Hackman.
Thanks to Helmut Auer for testing and helping to optimize the patch.
tda826x:
- set baseband cut-off to 19 MHz
tda10086:
- change the parameters of the carrier recovery loop
- toggle register 0x02 between 0x35 (tuning) and 0x00 (locked)
- invert STR and SNR values
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sliced VBI transfers use PIO instead of DMA. This was done inside the
interrupt handler, but since PIO accesses are very slow this meant that
a lot of time was spent inside the interrupt handler. All PIO copies are
now moved to a workqueue. This should fix various issues with missing time
ticks and remote key hits.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If this mutex_lock_interruptible() does fail due to signal_pending() then the
state of the driver will get trashed in interesting ways, because userspace
cannot and will not retry the close().
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the SAA7111 device is powered down, and requires re-initialisation when
the V4L device is opened (as on the NetWinder), the SAA7111 driver gets
completely confused about the current settings.
The problem is centred around the way the driver keeps _two_ cached copies
of the current settings - one of the struct video_picture settings, and one
of the registers.
When the decoder is re-initailised, the cached register settings are
overwritten, as are the values in the hardware registers. However, the
cached video_picture settings are not.
Resolve this by removing the useless and buggy second level of caching for
video_picture. Instead, provide a function which updates register values
if and only if the value we are going to write to the register has changed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The recent changes on Kconfig broke compilation when VIDEO_DEV is compiled
as module. On some cases, drivers like VIDEO_BUF are compiled with 'y' option
instead of 'm':
...
Thanks to: Toralf Forster <toralf.foerster@gmx.de> for pointing this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A bug in the ov7670 sensor causes it to introduce noise unless the CLKRC
register is rewritten *after* setting the image mode. Naturally,
resetting CLKRC in this way will cause other modes to fail. So
carefully poke the register only when indicated.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The proper method for powering down the sensor on OLPC systems has
changed somewhat; in particular, the sensor must be powered down
completely (rather than simply told to power down) or the associated
"camera active" LED will stay on.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow to use SECAM-BG with the FI1216MF tuner.
The selection is done with the secam=B module argument.
The default behaviour should be the same as before.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb-core is not started early enough when device drivers that use dvb are
compiled in so dvb_register_device fails (silently) since dvb_class is
NULL, this runs dvb_init using subsys_initcall instead of module_init.
dvb_register_device will now check the return value of class_device_create.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reverted the change to struct v4l2_pix_format. I completely missed that
this struct was used by existing ioctls so that changing it broke the ABI.
I will have to think of another way of setting the top/left coordinates
but for now this change is reverted to preserve compatibility.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
