At the moment the fixed mapping is by default strongly ordered (the
iommu_fixed=weak boot option must be used to make the fixed mapping weakly
ordered). If we're on a setup where the southbridge is being used in
endpoint mode (triblade and CAB boards) the default should be a weakly
ordered fixed mapping.
This adds a check so that if a node of type pcie-endpoint can be found in
the device tree the fixed mapping is set to be weak by default (but can be
overridden using iommu_fixed=strong).
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch implements support for HW based watchpoint via the
DBSR_DAC (Data Address Compare) facility of the BookE processors.
It does so by interfacing with the existing DABR breakpoint code
and adding the necessary bits and pieces for the new bits to
be properly set or cleared
Signed-off-by: Luis Machado <luisgpm@br.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A struct sysdev_attribute * parameter was added to the show routine by
commit 4a0b2b4dbe "sysdev: Pass the
attribute to the low level sysdev show/store function".
This eliminates a warning:
arch/powerpc/kernel/sysfs.c:538: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stash the first platform string matched by identify_cpu() in
powerpc_base_platform, and supply that to the ELF loader for the value
of AT_BASE_PLATFORM.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: Add transport feature handling stub for virtio_ring.
virtio: Rename set_features to finalize_features
virtio: Formally reserve bits 28-31 to be 'transport' features.
s390: use virtio_console for KVM on s390
virtio: console as a config option
virtio_console: use virtqueue notification for hvc_console
hvc_console: rework setup to replace irq functions with callbacks
virtio_blk: check for hardsector size from host
virtio: Use bus_type probe and remove methods
virtio: don't always force a notification when ring is full
virtio: clarify that ABI is usable by any implementations
virtio: Recycle unused recv buffer pages for large skbs in net driver
virtio net: Allow receiving SG packets
virtio net: Add ethtool ops for SG/GSO
virtio: fix virtio_net xmit of freed skb bug
This patch enables virtio_console as the default console on kvm for
s390. We currently use the same notify hack as lguest for early
console output. I will try to address this for lguest and s390 later.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
..otherwise oprofile will fall back on that poor timer interrupt.
Also replace the unreadable chain of if-statements with a "switch()"
statement instead. It generates better code, and is a lot clearer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suresh Siddha wants to fix a possible FPU leakage in error conditions,
but the fact that save/restore_i387() are inlines in a header file makes
that harder to do than necessary. So start off with an obvious cleanup.
This just moves the x86-64 version of save/restore_i387() out of the
header file, and moves it to the only file that it is actually used in:
arch/x86/kernel/signal_64.c. So exposing it in a header file was wrong
to begin with.
[ Side note: I'd like to fix up some of the games we play with the
32-bit version of these functions too, but that's a separate
matter. The 32-bit versions are shared - under different names
at that! - by both the native x86-32 code and the x86-64 32-bit
compatibility code ]
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arch/mips/kernel/stacktrace.c: Heiko can't type
kthread: reduce stack pressure in create_kthread and kthreadd
fix core/stacktrace changes on avr32, mips, sh
Commit 9d25d4db81 ("x86: BUILD_IRQ say
.text to avoid .data.percpu") added a ".text" specifier to make sure
that BUILD_IRQ() builds the irq trampoline in the text segment rather
than in some random left-over segment that the compiler happened to
leave the asm in.
However, we should also make sure that we switch back by adding a
".previous" at the end, so that there are no subtle issues with
subsequent compiler-generated code.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix header export, asm-x86/processor-flags.h, CONFIG_* leaks
x86: BUILD_IRQ say .text to avoid .data.percpu
xen: don't use sysret for sysexit32
x86: call early_cpu_init at the same point
* 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc:
Remove __DECLARE_SEMAPHORE_GENERIC
Remove asm/semaphore.h
Remove use of asm/semaphore.h
Add missing semaphore.h includes
Remove mention of semaphores from kernel-locking
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: put ColdFire head code into .text.head section
m68knommu: remove last use of CONFIG_FADS and CONFIG_RPXCLASSIC
m68knommu: remove RPXCLASSIC from the m68k tree
m68knommu: fec: remove FADS
m68knommu: MCF5307 PIT GENERIC_CLOCKEVENTS support
m68knommu: add read_barrier_depends() and irqs_disabled_flags()
m68knommu: add byteswap assembly opcode for ISA A+
m68knommu: add ffs and __ffs plattform which support ISA A+ or ISA C
m68knommu: add sched_clock() for the DMA timer
m68knommu: complete generic time
m68knommu: move code within time.c
m68knommu: m68knommu: add old stack trace method
m68knommu: Add Coldfire DMA Timer support
m68knommu: defconfig for M5407C3 board
m68knommu: defconfig for M5307C3 board
m68knommu: defconfig for M5275EVB board
m68knommu: defconfig for M5249EVB board
m68knommu: change to a configs directory for board configurations
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Ensure led->trigger is set earlier
leds: Add support for Philips PCA955x I2C LED drivers
leds: Fix sparse warnings in leds-h1940 driver
leds: mark led_classdev.default_trigger as const
leds: fix unsigned value overflow in atmel pwm driver
leds: Add pca9532 platform data for Thecus N2100
leds: Add pca9532 led driver
This fixes kernel http://bugzilla.kernel.org/show_bug.cgi?id=11112 (bogus
RTC update IRQs reported) for rtc-cmos, in two ways:
- When HPET is stealing the IRQs, use the first IRQ to grab
the seconds counter which will be monitored (instead of
using whatever was previously in that memory);
- In sane IRQ handling modes, scrub out old IRQ status before
enabling IRQs.
That latter is done by tightening up IRQ handling for rtc-cmos everywhere,
also ensuring that when HPET is used it's the only thing triggering IRQ
reports to userspace; net object shrink.
Also fix a bogus HPET message related to its RTC emulation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Report-by: W Unruh <unruh@physics.ubc.ca>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces the new syscall inotify_init1 (note: the 1 stands for
the one parameter the syscall takes, as opposed to no parameter before). The
values accepted for this parameter are function-specific and defined in the
inotify.h header. Here the values must match the O_* flags, though. In this
patch CLOEXEC support is introduced.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_inotify_init1
# ifdef __x86_64__
# define __NR_inotify_init1 294
# elif defined __i386__
# define __NR_inotify_init1 332
# else
# error "need __NR_inotify_init1"
# endif
#endif
#define IN_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd;
fd = syscall (__NR_inotify_init1, 0);
if (fd == -1)
{
puts ("inotify_init1(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("inotify_init1(0) set close-on-exit");
return 1;
}
close (fd);
fd = syscall (__NR_inotify_init1, IN_CLOEXEC);
if (fd == -1)
{
puts ("inotify_init1(IN_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("inotify_init1(O_CLOEXEC) does not set close-on-exit");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: add sys_ni stub]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces the new syscall pipe2 which is like pipe but it also
takes an additional parameter which takes a flag value. This patch implements
the handling of O_CLOEXEC for the flag. I did not add support for the new
syscall for the architectures which have a special sys_pipe implementation. I
think the maintainers of those archs have the chance to go with the unified
implementation but that's up to them.
The implementation introduces do_pipe_flags. I did that instead of changing
all callers of do_pipe because some of the callers are written in assembler.
I would probably screw up changing the assembly code. To avoid breaking code
do_pipe is now a small wrapper around do_pipe_flags. Once all callers are
changed over to do_pipe_flags the old do_pipe function can be removed.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_pipe2
# ifdef __x86_64__
# define __NR_pipe2 293
# elif defined __i386__
# define __NR_pipe2 331
# else
# error "need __NR_pipe2"
# endif
#endif
int
main (void)
{
int fd[2];
if (syscall (__NR_pipe2, fd, 0) != 0)
{
puts ("pipe2(0) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
printf ("pipe2(0) set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0)
{
puts ("pipe2(O_CLOEXEC) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new dup3 syscall. It extends the old dup2 syscall by one
parameter which is meant to hold a flag value. Support for the O_CLOEXEC flag
is added in this patch.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <time.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_dup3
# ifdef __x86_64__
# define __NR_dup3 292
# elif defined __i386__
# define __NR_dup3 330
# else
# error "need __NR_dup3"
# endif
#endif
int
main (void)
{
int fd = syscall (__NR_dup3, 1, 4, 0);
if (fd == -1)
{
puts ("dup3(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("dup3(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_dup3, 1, 4, O_CLOEXEC);
if (fd == -1)
{
puts ("dup3(O_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("dup3(O_CLOEXEC) set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new epoll_create2 syscall. It extends the old epoll_create
syscall by one parameter which is meant to hold a flag value. In this
patch the only flag support is EPOLL_CLOEXEC which causes the close-on-exec
flag for the returned file descriptor to be set.
A new name EPOLL_CLOEXEC is introduced which in this implementation must
have the same value as O_CLOEXEC.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <time.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_epoll_create2
# ifdef __x86_64__
# define __NR_epoll_create2 291
# elif defined __i386__
# define __NR_epoll_create2 329
# else
# error "need __NR_epoll_create2"
# endif
#endif
#define EPOLL_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd = syscall (__NR_epoll_create2, 1, 0);
if (fd == -1)
{
puts ("epoll_create2(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("epoll_create2(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_epoll_create2, 1, EPOLL_CLOEXEC);
if (fd == -1)
{
puts ("epoll_create2(EPOLL_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("epoll_create2(EPOLL_CLOEXEC) set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new eventfd2 syscall. It extends the old eventfd
syscall by one parameter which is meant to hold a flag value. In this
patch the only flag support is EFD_CLOEXEC which causes the close-on-exec
flag for the returned file descriptor to be set.
A new name EFD_CLOEXEC is introduced which in this implementation must
have the same value as O_CLOEXEC.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_eventfd2
# ifdef __x86_64__
# define __NR_eventfd2 290
# elif defined __i386__
# define __NR_eventfd2 328
# else
# error "need __NR_eventfd2"
# endif
#endif
#define EFD_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd = syscall (__NR_eventfd2, 1, 0);
if (fd == -1)
{
puts ("eventfd2(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("eventfd2(0) sets close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_eventfd2, 1, EFD_CLOEXEC);
if (fd == -1)
{
puts ("eventfd2(EFD_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("eventfd2(EFD_CLOEXEC) does not set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: add sys_ni stub]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new signalfd4 syscall. It extends the old signalfd
syscall by one parameter which is meant to hold a flag value. In this
patch the only flag support is SFD_CLOEXEC which causes the close-on-exec
flag for the returned file descriptor to be set.
A new name SFD_CLOEXEC is introduced which in this implementation must
have the same value as O_CLOEXEC.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <signal.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_signalfd4
# ifdef __x86_64__
# define __NR_signalfd4 289
# elif defined __i386__
# define __NR_signalfd4 327
# else
# error "need __NR_signalfd4"
# endif
#endif
#define SFD_CLOEXEC O_CLOEXEC
int
main (void)
{
sigset_t ss;
sigemptyset (&ss);
sigaddset (&ss, SIGUSR1);
int fd = syscall (__NR_signalfd4, -1, &ss, 8, 0);
if (fd == -1)
{
puts ("signalfd4(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("signalfd4(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = syscall (__NR_signalfd4, -1, &ss, 8, SFD_CLOEXEC);
if (fd == -1)
{
puts ("signalfd4(SFD_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("signalfd4(SFD_CLOEXEC) does not set close-on-exec flag");
return 1;
}
close (fd);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: add sys_ni stub]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to compile the v850 port brings many compile errors, one of them exists
since at least kernel 2.6.19.
There also seems to be noone willing to bring this port back into a usable
state.
This patch therefore removes the v850 port.
If anyone ever decides to revive the v850 port the code will still be
available from older kernels, and it wouldn't be impossible for the port to
reenter the kernel if it would become actively maintained again.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Make some variables and functions static, since they don't need to be
global.
- Remove an unused function - arch/um/kernel/time.c::sched_clock().
- Clean the style a bit as complained by checkpatch.pl.
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Remove arch_validate(), because no one uses it.
- Remove useless macro HAVE_ARCH_VALIDATE.
- Make the variable 'empty_bad_page' static.
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make activate_fd() and free_irq_by_irq_and_dev() static. Remove
init_aio_irq() since it has no users.
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI defines a hardware signature. BIOS calculates the signature according to
hardware configure and if hardware changes while hibernated, the signature
will change. In that case, S4 resume should fail.
Still, there may be systems on which this mechanism does not work correctly,
so it is better to provide a workaround for them. For this reason, add a new
switch to the acpi_sleep= command line argument allowing one to disable
hardware signature checking.
[shaohua.li@intel.com: build fix]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the obsolete and no longer used include/linux/pm_legacy.h
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Pavel Machek <pavel@suse.cz>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The real option is named AGP_ALPHA_CORE.
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of this field need a PFN instead of a physical address,
so replace node_boot_start with node_min_pfn.
[Lee.Schermerhorn@hp.com: fix spurious BUG_ON() in mark_bootmem()]
Signed-off-by: Johannes Weiner <hannes@saeureba.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using the variable mmu_huge_psize to keep track of the huge
page size we use an array of MMU_PAGE_* values. For each supported huge
page size we need to know the hugepte_shift value and have a
pgtable_cache. The hstate or an mmu_huge_psizes index is passed to
functions so that they know which huge page size they should use.
The hugepage sizes 16M and 64K are setup(if available on the hardware) so
that they don't have to be set on the boot cmd line in order to use them.
The number of 16G pages have to be specified at boot-time though (e.g.
hugepagesz=16G hugepages=5).
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The huge page size is defined for 16G pages. If a hugepagesz of 16G is
specified at boot-time then it becomes the huge page size instead of the
default 16M.
The change in pgtable-64K.h is to the macro pte_iterate_hashed_subpages to
make the increment to va (the 1 being shifted) be a long so that it is not
shifted to 0. Otherwise it would create an infinite loop when the shift
value is for a 16G page (when base page size is 64K).
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 16G huge pages have to be reserved in the HMC prior to boot. The
location of the pages are placed in the device tree. This patch adds code
to scan the device tree during very early boot and save these page
locations until hugetlbfs is ready for them.
Acked-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 16G page locations have been saved during early boot in an array. The
alloc_bootmem_huge_page() function adds a page from here to the
huge_boot_pages list.
Acked-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an hugepagesz=... option similar to IA64, PPC etc. to x86-64.
This finally allows to select GB pages for hugetlbfs in x86 now that all
the infrastructure is in place.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straight forward extensions for huge pages located in the PUD instead of
PMDs.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The goal of this patchset is to support multiple hugetlb page sizes. This
is achieved by introducing a new struct hstate structure, which
encapsulates the important hugetlb state and constants (eg. huge page
size, number of huge pages currently allocated, etc).
The hstate structure is then passed around the code which requires these
fields, they will do the right thing regardless of the exact hstate they
are operating on.
This patch adds the hstate structure, with a single global instance of it
(default_hstate), and does the basic work of converting hugetlb to use the
hstate.
Future patches will add more hstate structures to allow for different
hugetlbfs mounts to have different page sizes.
[akpm@linux-foundation.org: coding-style fixes]
Acked-by: Adam Litke <agl@us.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
free_area_init_node() gets passed in the node id as well as the node
descriptor. This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.
I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The double indirection here is not needed anywhere and hence (at least)
confusing.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This uses the new vm_ops->access to allow gdb to access the SPU local
store. We currently prevent access to problem state registers, this can
be done later if really needed but it's safer not to.
[akpm@linux-foundation.org: fix typo]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds ioremap_prot and pte_pgprot() so that one can extract protection
bits from a PTE and use them to ioremap_prot() (in order to support ptrace
of VM_IO | VM_PFNMAP as per Rik's patch).
This moves a couple of flag checks around in the ioremap implementations
of arch/powerpc. There's a side effect of allowing non-cacheable and
non-guarded mappings on ppc32 which before would always have _PAGE_GUARDED
set whenever _PAGE_NO_CACHE is.
(standard ioremap will still set _PAGE_GUARDED, but ioremap_prot will be
capable of setting such a non guarded mapping).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use generic_access_phys as the access_process_vm access function for
/dev/mem mappings. This makes it possible to debug the X server.
[akpm@linux-foundation.org: repair all the architectures which broke]
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Benjamin Herrensmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to be able to debug things like the X server and programs using
the PPC Cell SPUs, the debugger needs to be able to access device memory
through ptrace and /proc/pid/mem.
This patch:
Add the generic_access_phys access function and put the hooks in place
to allow access_process_vm to access device or PPC Cell SPU memory.
[riel@redhat.com: Add documentation for the vm_ops->access function]
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Benjamin Herrensmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a lot of places that define either a single bootmem descriptor or an
array of them. Use only one central array with MAX_NUMNODES items instead.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag platforms as HAVE_CLK (or not) in Kconfig, based on whether they
support <linux/clk.h> calls, so that otherwise portable drivers which need
those calls can list that dependency.
Something like this is a prerequisite for merging the musb_hdrc driver,
currently used on platforms including Davinci, OMAP2430, OMAP3xx ... and
the discrete TUSB6010 chip, which doesn't have a natural platform
dependency. (Used with OMAP 2420 in current Nokia N8x0 tablets.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds platform data to the AC97C platform device. This will
let the board add a GPIO line which is connected to the external codecs
reset line.
The platform data, ac97c_platform_data, must also contain the DMA
controller ID, RX channel ID and TX channel ID.
Tested with Wolfson WM9712 and AP7000.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
When I edit the x86_64 Makefile to -fno-unit-at-a-time, bootup panics
on 0xCCs in IRQ0x3e_interrupt(): IRQ0x20_interrupt etc. have got linked
into .data.percpu. Perhaps there are other ways of triggering that:
specify ".text" in the BUILD_IRQ() macro for safety.
I've been using -fno-unit-at-a-time (to lessen inlining, for easier
debugging) for a long time.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When implementing sysexit32, don't let Xen use sysret to return to
userspace. That results in usermode register state being trashed.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Call early_cpu_init() at the same (early) point in setup_arch().
The x86_64 code was calling it relatively late, after when other arch
code need to do cpu-related setup which depends on it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: hrtick_enabled() should use cpu_active()
sched, x86: clean up hrtick implementation
sched: fix build error, provide partition_sched_domains() unconditionally
sched: fix warning in inc_rt_tasks() to not declare variable 'rq' if it's not needed
cpu hotplug: Make cpu_active_map synchronization dependency clear
cpu hotplug, sched: Introduce cpu_active_map and redo sched domain managment (take 2)
sched: rework of "prioritize non-migratable tasks over migratable ones"
sched: reduce stack size in isolated_cpu_setup()
Revert parts of "ftrace: do not trace scheduler functions"
Fixed up conflicts in include/asm-x86/thread_info.h (due to the
TIF_SINGLESTEP unification vs TIF_HRTICK_RESCHED removal) and
kernel/sched_fair.c (due to cpu_active_map vs for_each_cpu_mask_nr()
introduction).
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
This patch adjusts the placement of a reference context from
a spu affinity chain. The reference context can now be placed
only on nodes that have enough spus not intended to be used by
another gang (already running on the node).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: Roland McGrath <roland@redhat.com>
Currenlt,, it is possible to lock aff_mutex and
cbe_spu_info[n].list_mutex in different orders, allowing a deadlock to
occur. With this change, aff_mutex is not taken within a list_mutex
critical section anymore.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: Roland McGrath <roland@redhat.com>
This adds a fast path for 64-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
This path does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Signed-off-by: Roland McGrath <roland@redhat.com>
This short-circuit path in sysret_signal looks wrong to me.
AFAICT, in practice the branch is never taken--and if it were,
it would go wrong. To wit, try loading a module whose init
function does set_thread_flag(TIF_IRET), and see insmod crash
(presumably with a wrong user stack pointer).
This is because the FIXUP_TOP_OF_STACK work hasn't been done yet
when we jump around the call to ptregscall_common and get to
int_with_check--where it expects the user RSP,SS,CS and EFLAGS to
have been stored by FIXUP_TOP_OF_STACK.
I don't think it's normally possible to get to sysret_signal with no
_TIF_DO_NOTIFY_MASK bits set anyway, so these two instructions are
already superfluous. If it ever did happen, it is harmless to call
do_notify_resume with nothing for it to do.
Signed-off-by: Roland McGrath <roland@redhat.com>
Based upon a report by Daniel Smolik.
We do it too early, which triggers a BUG in
cpufreq_register_notifier().
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
My copying of linux/init.h didn't go far enough. The definition of
__used singled out gcc minor version 3, but didn't care what the major
version was. This broke when unit-at-a-time was added and gcc started
throwing out initcalls.
This results in an early boot crash when ptrace tries to initialize a
process with an empty, uninitialized register set.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the old kgdb reminants from ARCH=powerpc and
implements the new style arch specific stub for the common kgdb core
interface.
It is possible to have xmon and kgdb in the same kernel, but you
cannot use both at the same time because there is only one set of
debug hooks.
The arch specific kgdb implementation saves the previous state of the
debug hooks and restores them if you unconfigure the kgdb I/O driver.
Kgdb should have no impact on a kernel that has no kgdb I/O driver
configured.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This patch adds the ARCH=arm specific a kgdb backend, originally
written by Deepak Saxena <dsaxena@plexity.net> and George Davis
<gdavis@mvista.com>. Geoff Levand <geoffrey.levand@am.sony.com>,
Nicolas Pitre, Manish Lachwani, and Jason Wessel have contributed
various fixups here as well.
The KGDB patch makes one change to the core ARM architecture such that
the traps are initialized early for use with the debugger or other
subsystems.
[ mingo@elte.hu: small cleanups. ]
[ ben-linux@fluff.org: fixed early_trap_init ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Deepak Saxena <dsaxena@plexity.net>
Thecus N2100 has leds and a buzzer attached to a pca9532 controller. Attach
the driver to the i2c bus and define the pca9532 pin coniguration for this
platform in n2100_leds.
With this patch, support for N2100 should be complete in mainline Linux.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
We're calling request_irq() with a IRQs disabled.
No straightforward fix exists because we want to
enable these IRQs and setup state atomically before
getting into the IRQ handler the first time.
What happens now is that we mark the VIRQ to not be
automatically enabled by request_irq(). Then we
make explicit enable_irq() calls when we grab the
LDC channel.
This way we don't need to call request_irq() illegally
under the LDC channel lock any more.
Bump LDC version and release date.
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the ColdFire head start up code to be in the .text.head segment.
And make sure that segment is at the start of the final linked text
segment. Fixes the linker warnings about section use mis-matches:
WARNING: vmlinux.o(.text+0xa8): Section mismatch in reference from the variable _clear_bss to the function .init.text:start_kernel()
The function _clear_bss() references
the function __init start_kernel().
This is often because _clear_bss lacks a __init
annotation or the annotation of start_kernel is wrong.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The PIT code has been changed in order to suppport GENERIC_CLOCKEVENTS.
The priority of the PIT clocksource has been decreased in favor of the
DMA timer.
pit_cycles_per_jiffy become a constant (PIT_CYCLES_PER_JIFFY) because it
is known at compile time and does not change afterwards.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
the ff1 and bitrev opcode appears in ISA C and ISA A+ what isn't
supported by all plattforms. The assembly optimization is automaticly
enabled if the compiler understand the required cpu keyword.
My m5235 seems to boot and run fine so far.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
with this printk() and other sched_clock() user use the more precise
timestamps. The highly optimized math is from arch/x86/kernel/tsc_32.c.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
do_set_rtc() isn't required because the work that is handled is
allready served if read_persistent_clock() & update_persistent_clock()
are implemented and CONFIG_GENERIC_CMOS_UPDATE is. sync_cmos_clock()
looks very familiar :)
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This patch creates two functions do_set_rtc() and read_rtc_mmss()
based on allready available code.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The old method is used when frame pointers are not available.
Also fix formating with CONFIG_KALLSYMS=n which eliminates \n.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This one could be used as a hrtimer.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove the old example m68knommu defconfig. Create a configs directory
for specific board configurations. Make the m5208evb the default.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32: pass -m32 when building vmlinux.lds
sparc: Fixes the DRM layer build on sparc.
ide: merge <asm-sparc/ide_64.h> with <asm-sparc/ide_32.h>
ide: <asm-sparc/ide_64.h>: use __raw_{read,write}w()
ide: <asm-sparc/ide_32.h>: use __raw_{read,write}w()
ide: <asm-sparc/ide_64.h>: use %r0 for outw_be()
sparc64: Do not define BIO_VMERGE_BOUNDARY.
kcalloc is supposed to be called with the count as its first argument and
the element size as the second.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Otherwise it breaks since we merged asm/page.h
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix crash due to missing debugctlmsr on AMD K6-3
x86: add PTE_FLAGS_MASK
x86: rename PTE_MASK to PTE_PFN_MASK
x86: fix pte_flags() to only return flags, fix lguest (updated)
x86: use setup_clear_cpu_cap with disable_apic, fix
x86: move the last Dprintk instance to pr_debug()
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
remove CONFIG_KMOD from core kernel code
remove CONFIG_KMOD from lib
remove CONFIG_KMOD from sparc64
rework try_then_request_module to do less in non-modular kernels
remove mention of CONFIG_KMOD from documentation
make CONFIG_KMOD invisible
modules: Take a shortcut for checking if an address is in a module
module: turn longs into ints for module sizes
Shrink struct module: CONFIG_UNUSED_SYMBOLS ifdefs
module: reorder struct module to save space on 64 bit builds
module: generic each_symbol iterator function
module: don't use stop_machine for waiting rmmod
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (49 commits)
powerpc: Fix build bug with binutils < 2.18 and GCC < 4.2
powerpc/eeh: Don't panic when EEH_MAX_FAILS is exceeded
fbdev: Teaches offb about palette on radeon r5xx/r6xx
powerpc/cell/edac: Log a syndrome code in case of correctable error
powerpc/cell: Add DMA_ATTR_WEAK_ORDERING dma attribute and use in Cell IOMMU code
powerpc: Indicate which oprofile counters to use while in compat mode
powerpc/boot: Change spaces to tabs
powerpc: Remove duplicate 6xx option in Kconfig
powerpc: Use PPC_LONG and PPC_LONG_ALIGN in lib/string.S
powerpc: Use PPC_LONG_ALIGN in uaccess.h
powerpc: Add a #define for aligning to a long-sized boundary
powerpc: Fix OF parsing of 64 bits PCI addresses
powerpc: Use WARN_ON(1) instead of __WARN()
powerpc: Fix support for latencytop
powerpc/ps3: Update ps3_defconfig
powerpc/ps3: Add a sub-match id to ps3_system_bus
powerpc: Add a 6xx defconfig
powerpc/dma: Use the struct dma_attrs in iommu code
powerpc/cell: Add support for power button of future IBM cell blades
powerpc/cell: Cleanup sysreset_hack for IBM cell blades
...
currently if you use PTRACE_SINGLEBLOCK on AMD K6-3 (i586) it will crash.
Kernel now wrongly assumes existing DEBUGCTLMSR MSR register there.
Removed the assumption also for some other non-K6 CPUs but I am not sure there
(but it can only bring small inefficiency there if my assumption is wrong).
Based on info from Roland McGrath, Chuck Ebbert and Mikulas Patocka.
More info at:
https://bugzilla.redhat.com/show_bug.cgi?id=456175
Signed-off-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
One place is just a comment, the other a conditional, unused
inclusion of linux/kmod.h.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Also includes a few Kconfig files (xtensa, blackfin)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
PTE_PFN_MASK was getting lonely, so I made it a friend.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rusty, in his peevish way, complained that macros defining constants
should have a name which somewhat accurately reflects the actual
purpose of the constant.
Aside from the fact that PTE_MASK gives no clue as to what's actually
being masked, and is misleadingly similar to the functionally entirely
different PMD_MASK, PUD_MASK and PGD_MASK, I don't really see what the
problem is.
But if this patch silences the incessent noise, then it will have
achieved its goal (TODO: write test-case).
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
(Jeremy said:
rusty: use PTE_MASK
rusty: use PTE_MASK
rusty: use PTE_MASK
When I asked:
jsgf: does that include the NX flag?
He responded eloquently:
rusty: use PTE_MASK
rusty: use PTE_MASK
yes, it's the official constant of masking flags out of ptes
)
Change a15af1c9ea 'x86/paravirt: add
pte_flags to just get pte flags' removed lguest's private pte_flags()
in favor of a generic one.
Unfortunately, the generic one doesn't filter out the non-flags bits:
this results in lguest creating corrupt shadow page tables and blowing
up host memory.
Since noone is supposed to use the pfn part of pte_flags(), it seems
safest to always do the filtering.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-and-morning-tea-spilled-by: Ingo Molnar <mingo@elte.hu>
beauty fix: /proc/cpuinfo will still show apic feature even if
we booted up with it disabled.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This converts all instances of bus_id in the sparc core kernel to use
either dev_set_name(), or dev_name() depending on the need.
This is done in anticipation of removing the bus_id field from struct
driver.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the new generic int attribute accessors for the x86 mce tolerant
attribute. Simple example to illustrate the new macros.
There are much more places all over the tree that could be converted
like this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have the dev_printk() variants for this kind of thing, use them
instead of directly trying to access the bus_id field of struct device.
This is done in order to remove bus_id entirely.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
binutils < 2.18 has a bug that makes it misbehave when taking an
ELF file with all segments at load address 0 as input. This
happens when running "strip" on vmlinux, because of the AT() magic
in this linker script. People using GCC >= 4.2 won't run into
this problem, because the "build-id" support will put some data
into the "notes" segment (at a non-zero load address).
To work around this, we force some data into both the "dummy"
segment and the kernel segment, so the dummy segment will get a
non-zero load address. It's not enough to always create the
"notes" segment, since if nothing gets assigned to it, its load
address will be zero.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Tested-By: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch changes the EEH_MAX_FAILS action from panic to printing an
error message. Panicking under under this condition is too harsh.
Although performance will be affected and the device may not recover,
the system is still running, which at the very least should allow for a
more graceful shutdown. The patch also removes the msleep() within a
spinlock, which can lead to a deadlock and is not recommended.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Introduce a new dma attriblue DMA_ATTR_WEAK_ORDERING to use weak ordering
on DMA mappings in the Cell processor. Add the code to the Cell's IOMMU
implementation to use this code.
Dynamic mappings can be weakly or strongly ordered on an individual basis
but the fixed mapping has to be either completely strong or completely weak.
This is currently decided by a kernel boot option (pass iommu_fixed=weak
for a weakly ordered fixed linear mapping, strongly ordered is the default).
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While running on a system with new hardware and a kernel where the
cpu_specs[] table does not recognize the new hardware, the identify_cpu()
routine will select the default case as it searches through cpu_specs[]
in an attempt to match the real PVR. Once the default case is selected,
non of the oprofile counters and/or fields have been set up or defined.
When identify_cpu() is called once more with the logical PVR, some of
the cpu specific fields are replaced with the exception of the oprofile
related ones. However, in the case where we have actually taken the
default case while searching for the real PVR, we need to tell
oprofile that we are now running in compatibility mode so it can pick up
the correct counters. We do this by setting the oprofile_cpu_type field
to be that taken from the cpu_specs[] for the cpu we are now emulating.
This change will detect that we are now altering the real PVR and determine
if we also need to update the oprofile_cpu_type field.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For C code spaces versus tabs is just a religious issue,
but for Makefiles it actually matters.
This patch fixes he following errors:
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:166: *** missing separator. Stop.
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:171: *** missing separator. Stop.
Since this was inside an ifdef DTC_GENPARSER it was not a problem unless
someone wanted to regenerate the shipped generated files.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The real option is above in the same Kconfig file.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace ifdef clutter with the PPC_LONG and PPC_LONG_ALIGN macros
for readability.
No change to the generated code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The OF parsing code for PCI addresses isn't always treating properly
the address space indication 0b11 (ie. 0x3) as meaning 64 bits
memory space.
This means that it fails to parse addresses for PCI BARs that have
this encoding set by the firmware, which happens on some SLOF
versions and breaks offb palette handling on Powerstation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
__WARN() is not defined for all configs, use WARN_ON(1) instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to pass the kernel stack pointer instead of the user space
stack pointer in save_stack_trace_tsk().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add sub match id for ps3 system bus so that two different system bus
devices can be connected to a shared device.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a defconfig from Dave Jones and should be similar (if not
identical) to the fedora ppc32 defconfig. The intent is to cover all
cache coherent 6xx based chips and platforms as reasonable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update iommu_alloc() to take the struct dma_attrs and pass them on to
tce_build(). This change propagates down to the tce_build functions of
all the platforms.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the power button on future IBM cell blades.
It actually doesn't shut down the machine. Instead it exposes an
input device /dev/input/event0 to userspace which sends KEY_POWER
if power button has been pressed.
haldaemon actually recognizes the button, so a plattform independent acpid
replacement should handle it correctly.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a config option for the sysreset_hack used for
IBM Cell blades. The code is moves from pervasive.c into ras.c and
gets it's own init method.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a cpufreq governor that takes the number of running spus
into account. It's very similar to the ondemand governor, but not as complex.
Instead of hacking spu load into the ondemand governor it might be easier to
have cpufreq accepting multiple governors per cpu in future.
Don't know if this is the right way, but it would keep the governors simple.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
DDR2 memory DIMMs on the Axon could be accessed only as one partition
when using file system drivers which are using the direct_access() method.
This patch enables for such file system drivers to access Axon's DDR2 memory
even if it is splitted in several partitions.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Axonram module registers one block device for each DDR2 DIMM found
on a system. This means that each DDR2 DIMM becomes its own block device
major number. This patch lets axonram module to register the only one
block device for all DDR2 DIMMs which also spares kernel resources.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: (25 commits)
mmtimer: Push BKL down into the ioctl handler
[IA64] Remove experimental status of kdump
[IA64] Update ia64 mmr list for SGI uv
[IA64] Avoid overflowing ia64_cpu_to_sapicid in acpi_map_lsapic()
[IA64] adding parameter check to module_free()
[IA64] improper printk format in acpi-cpufreq
[IA64] pv_ops: move some functions in ivt.S to avoid lack of space.
[IA64] pvops: documentation on ia64/pv_ops
[IA64] pvops: add to hooks, pv_time_ops, for steal time accounting.
[IA64] pvops: add hooks, pv_irq_ops, to paravirtualized irq related operations.
[IA64] pvops: add hooks, pv_iosapic_ops, to paravirtualize iosapic.
[IA64] pvops: define initialization hooks, pv_init_ops, for paravirtualized environment.
[IA64] pvops: paravirtualize NR_IRQS
[IA64] pvops: paravirtualize entry.S
[IA64] pvops: paravirtualize ivt.S
[IA64] pvops: paravirtualize minstate.h.
[IA64] pvops: define paravirtualized instructions for native.
[IA64] pvops: preparation for paravirtulization of hand written assembly code.
[IA64] pvops: introduce pv_cpu_ops to paravirtualize privileged instructions.
[IA64] pvops: add an early setup hook for pv_ops.
...
There are a couple of places where (P)Dprintk is used which is an old
compile time enabled printk wrapper. Convert it to the generic
pr_debug().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'x86/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (160 commits)
x86: remove extra calling to get ext cpuid level
x86: use setup_clear_cpu_cap() when disabling the lapic
KVM: fix exception entry / build bug, on 64-bit
x86: add unknown_nmi_panic kernel parameter
x86, VisWS: turn into generic arch, eliminate leftover files
x86: add ->pre_time_init to x86_quirks
x86: extend and use x86_quirks to clean up NUMAQ code
x86: introduce x86_quirks
x86: improve debug printout: add target bootmem range in early_res_to_bootmem()
Subject: devmem, x86: fix rename of CONFIG_NONPROMISC_DEVMEM
x86: remove arch_get_ram_range
x86: Add a debugfs interface to dump PAT memtype
x86: Add a arch directory for x86 under debugfs
x86: i386: reduce boot fixmap space
i386/xen: add proper unwind annotations to xen_sysenter_target
x86: reduce force_mwait visibility
x86: reduce forbid_dac's visibility
x86: fix two modpost warnings
x86: check function status in EDD boot code
x86_64: ia32_signal.c: remove signal number conversion
...
... so don't need to call clear_cpu_cap again in early_identify_cpu,
and could use cleared_cpu_caps like other places.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'kvm-updates-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (70 commits)
KVM: Adjust smp_call_function_mask() callers to new requirements
KVM: MMU: Fix potential race setting upper shadow ptes on nonpae hosts
KVM: x86 emulator: emulate clflush
KVM: MMU: improve invalid shadow root page handling
KVM: MMU: nuke shadowed pgtable pages and ptes on memslot destruction
KVM: Prefix some x86 low level function with kvm_, to avoid namespace issues
KVM: check injected pic irq within valid pic irqs
KVM: x86 emulator: Fix HLT instruction
KVM: Apply the kernel sigmask to vcpus blocked due to being uninitialized
KVM: VMX: Add ept_sync_context in flush_tlb
KVM: mmu_shrink: kvm_mmu_zap_page requires slots_lock to be held
x86: KVM guest: make kvm_smp_prepare_boot_cpu() static
KVM: SVM: fix suspend/resume support
KVM: s390: rename private structures
KVM: s390: Set guest storage limit and offset to sane values
KVM: Fix memory leak on guest exit
KVM: s390: dont allocate dirty bitmap
KVM: move slots_lock acquision down to vapic_exit
KVM: VMX: Fake emulate Intel perfctr MSRs
KVM: VMX: Fix a wrong usage of vmcs_config
...
